Power PC G-5 and Leopard

I have a non-intel G-5. Will Leopard install and run on my computer when it comes out?
G-5 , 2.3 Mac OS X (10.4.9)

Yes.

Similar Messages

1st generation MacBook, battery and Leopard issues; looking for help please

I have a 1st generation MacBook that started having battery problems immediately after installing Leopard. it was the same issue many others have complained about; battery life shortened and shutting down while on battery power with no warning. I have never had that problem while using Tiger. I experienced this with both 10.5.0 and the stand alone upgrade of 10.5.1 using an erase and install method.
(BTW, as a side note: I'm religious about calibrating my battery every month and use a program called "CoconutBattery" to document the results. Prior to Leopard, the battery measured 97-99% capacity. Three days after Leopard was installed it was time for another check, the result was 74% capacity.)
I had a clone backup of Tiger and immediately restored my MacBook, but the problem followed Tiger. I have Applecare and called support. Both myself and the tech found it rather hard to believe that the battery just suddenly failed coincidentally after the Leopard install. We went through the regular things; SMC reset, firmware checks, diagnostics, repair permissions, etc.
We believe it has to do with the Battery Updater package. I had gone between both versions of 1.2 and 1.3, but the problem remained with both Tiger and Leopard. The tech decided to send me a new battery (it's on the way) and I wish to try installing Leopard again. As long as I have my cloned Tiger image, all I have to lose is my time, but hopefully, not another battery! I would honestly like to get Leopard running on this machine.
But... here's my question. In reading through these discussions in both the Leopard and MacBook forum, there doesn't seem to be any consensus of which BatteryUpdater package to use. The Apple tech honestly told me he didn't know. Also, if the BU package "writes" to the battery (which it states it does), can it be downgraded once v1.3 has been installed? I mean, should I leave the battery out, install Leopard, then manually update BU to v1.2 before installing the battery (if possible)? I do plan on testing the new battery with my Tiger install, just to verify it is working as it was before.
There are a lot of people here claiming to be knowledgeable about Leopard, never had any problems with a variety of machines, etc, etc, so I would appreciate your input. Please don't speculate, but if you're using a version of BU that works with Leopard and your 1st Gen MacBook, I would appreciate you telling me about it. I have tried to document and methodically relate everything I've done so far, but if you need additional information, just let me know.
I noticed Leopard had installed BU v1.3 when I checked it, so it must use that as default, since I noticed Tiger had v1.2.
OR, am I way off base on this? Can anyone think of another reason I may have had this problem? Am I barking up the wrong tree by concentrating on the BatteryUpdater package? Is it possible all these batteries are failing under a Leopard install maybe due to some unknown reason?
Any knowledgeable advice or suggestions are welcome, thanks!

Well, Ding Dang y'all... it appears the battery was the culprit. I received my replacement battery from Apple and followed the same steps and everything seems to be working fine.
It sure was strange that the battery started this problem immediately after Leopard was installed... I don't know what to say about that, unless BatteryUpdater v1.3 started the chain of events.
In case it helps someone else, here's exactly what I did (rebooted through each step):
- Backed up data; unauthorized computer from iTunes
- Erase and install from the Leopard disc, while keeping the old battery in
- Installed Leopard, did software updates except for delta 10.5.1 update
- Applied combo update of 10.5.1 from separately downloaded file
- Found BatteryUpdater Bundle (BU) of v1.3, moved to trash, rebooted
- Ran software updates, BU v1.2 was found and installed
- Then, swapped out battery to new battery
- Tested unit, seems to be okay now, no shutdown issues, battery runtime seems normal
Thanks to all that had advice and suggestions. It was enough to get me to try it again. Now, I have two more machines to upgrade, since these are production machines, I'll probably wait awhile. But, having this is a real treat.
Have a great holiday everyone!

"Moving" Tiger and Leopard OS's from G4 (32b) to G5 (64b)

I plan to image Tiger (10.4) and Leopard (10.5) from my Power Mac G4 (Quicksilver 2002) to a recently acquired a Power Mac G5 (Early 2005). My questions are:
1. Tiger and Leopard were installed on a G4, a 32 bit processor, but the G5 is a 64 bit processor. Do I need to do anything after I’ve “installed” the G4 Tiger and Leopard on the G5 to have them function as 64 bit Operating Systems (a.they can detect which processor they are installed on automagically and don’t need my intervention OR b.I have to toggle something OR c.I have to reinstall one/both of the Operating Systems on the G5 for them to function as 64 bit Operating Systems)?
2. How can I tell if the OS is running as a 32 bit or 64 bit process?
TIA.

Hi Barubin,
I'm no expert on OS X's internals, but I believe Tiger and Leopard's kernel still is 32-Bit, but allows 32-64-bit bridging. In Leopard's Activity Monitor I can only find two apps running in 64-Bit mode:
usbmuxd
IIDCAssistant
The best way of getting 64-Bit is to upgrade to Snow Leopard on Intel, I'm afraid.
Your target-disk method or BDAqua's suggestions should work just fine, but I usually find hdiutil to be generally more reliable, plus I can keep around a system image for safety's sake. When I say reliable, I mean that you can always interrupt the image creation by using CTRL-C or check whether it is actually throwing any errors. The GUI has hung on me on occasions. I also love UNIX, which helps!
I've never done a speed comparison between Disk Utility and its CLI counterparts, but I like the verbosity/flexibility provided by the CLI. It's a matter of taste, really. If you're not comfortable using the CLI, stick to the other options.
The purpose of asr -imagescan (asr stands for Apple Software Restore), is to rebuild the target image and replace it with a checksummed and reordered (optimised) version, so it can then be verified against the contents of your target volume after you're restored the data. Also, scanning the image allows you to do a block restore, which is effectively a blazingly fast blind copy. In a matter of minutes you can easily restore 15 GB of data into your chosen volume, as opposed to not scanning it with asr or Disk Utility and the restore operation defaulting to a normal image mount --> data copy operation, which is slow and inefficient. It's a tradeoff really. You can wait for ages restoring, or creating the image
I rather wait for image creation since it's the safest and cleanest option data-wise.
Check out:
$ man asr
$ man hdiutil
I'm confident it will all work just fine with your heart transplant!
Cheers

"disc is too slow or system overload" -- L8 and Leopard

Hi all, I'm mixing something on Logic -- a two track piece, one an a Addictive Drums drum track, and a bass with some effects from Guitar Rig 3, and L8 keeps freezing during playback with the message above ("disc to slow or system overload.") This never happened to me before. Can anyone suggest a culprit and solution?

yeah ...i've always had a dedicated firewire audio hard drive so i don't think its that....i think its the software instruments and 3rd party plugins....they're probably draining more power than usual<</div>
Right, the external hard drive only makes a difference with audio tracks.
although Addictive drums might be streaming samples from the hard drive.
You say the instruments and plugins might be draining more power than usual? Perhaps it's Logic 8 and Leopard using more CPU power than Logic 7 and Tiger. Have you had the CPU/Drive performance meters visible when the overload message appears? Is it the CPU meter that's spiking or the drive meter?
pancenter-

TS3938 I have a power pc processor g5 and cannot load adobe flashplayer. Anyone know how?

I have a power PC processor g5 and cannot load adobe flashplayer. Does anyone know how?

You can check here: http://www.adobe.com/products/flash/about/ to see which version you should install for your Mac and OS. Note that version 10,1,102,64 is the last version available to PPC Mac users*. The latest version,10.3.183.23 or later, is for Intel Macs only running Tiger or Leopard, as Adobe no longer support the PPC platform. Version 11.4.402.265 or later is for Snow Leopard onwards.
* Unhelpfully, if you want the last version for PPC (G4 or G5) Macs, you need to go here: http://kb2.adobe.com/cps/142/tn_14266.html and scroll down to 'Archived Versions/Older Archives'. Flash Player 10.1.102.64 is the one you download. More information here: http://kb2.adobe.com/cps/838/cpsid_83808.html
You should first uninstall any previous version of Flash Player, using the uninstaller from here (make sure you use the correct one!):
http://kb2.adobe.com/cps/909/cpsid_90906.html
and also that you follow the instructions closely, such as closing ALL applications first before installing. You must also carry out a permission repair after installing anything from Adobe.
(If you are running a PPC Mac with Flash Player 10.1.102.64 and are having problems with watching videos on FaceBook or other sites, try the following solution which fools the site into thinking that you are running the version 11.5.502.55:)
Download this http://scriptogr.am/nordkril/post/adobe-flash-11.5-for-powerpc to your desktop, unzip it, and replace the current Flash Player plug-in which is in your main/Library/Internet Plug-Ins folder, (not the user Library). Save the old one just in case this one doesn't work.

G4 MDD FW800 Dual Boot Tiger and Leopard

I have a Power Mac G4 1.25 Dual MDD FW800 currently running Tiger 10.4.9. I would like to install Leopard on a partition or a second hard drive so I can dual boot between Tiger and Leopard. Will the FW800 model allow this without eliminating Tiger or creating any issues with using Tiger? I recall reading somewhere that the MDD FW800 could not run Jaguar and Tiger concurrently but I don't know if this is true? Anyone running this Tiger-Leopard dual boot setup?
Thanks Della

Your MDD's are FW800 also?
What you are asking doesn't matter.
ALL G4 machines, including ALL MDD machines, including the FW800 CAN maintain two or more OS versions (such as Tiger and Leopard) and CAN boot back and forth between the versions.
Any G4 that I have ever had, Sawtooth to MDD/FW800 has run two, three and four OS versions.
I currently have OS9, Panther, Tiger and Leopard installed on this machine.
Another source had told me that the FW800 MDD could not boot back to a previous version OS once a newer version OS had been installed ie once Leopard was installed you could not boot from Tiger again from another startup disk?
Your source is incorrect, and is telling you contrary to all the content of the entire internet regarding the topic.
The FW800 cannot boot to OS 9 (any version) nor can it boot to OS X earlier than 10.2.3.
As with ANY G4, it cannot run OS X Snow Leopard (10.6).
Those are the ONLY limitations.
ALL other OS versions after OS X 10.2.3, in any number of combinations, may be present as boot volumes on the machine.
If you had 4 drives with 3 OS versions each, as long as the version was within the machines compatibility, it would be fine and boot would be supported.

IMac (Late 2006) Stalls with EFI 1.2 and Leopard

A few days ago, I installed both the iMac 1.2 EFI Firmware update and Leopard on my late 2006 20" iMac. Since then, I've seen random momentary stalls throughout the system.
It sometimes happens while scrolling a web page, displaying a sheet, opening a stack, browsing CoverFlow, and so on. I don't know how to intentionally recreate it, it just seems to happen. It often (always?) seems to coincide with some disk activity.
I don't remember this behavior on the same hardware in the past, so either it's something with the firmware update or Leopard. Has anyone seen anything else like this?
Thanks in advance.

Some people reported various bugs after installing the firmware update. Shutting it off and turning it back was all that was needed to fix the bugs.

I renamed a power point a file and now when I try to open it it keeps giving me the error code -108. If I try to open or copy it say: The operation can't be completed because one or more required items can't be found. (Error code -43). What do I do?

I renamed a power point a file and now when I try to open it it keeps giving me the error code -108. If I try to open or copy it say: The operation can’t be completed because one or more required items can’t be found. (Error code -43). What do I do?

Post in Microsoft's Powerpoint (Mac) message boards.

Endnote X1 and Leopard

Has anyone tried using Endnote X1 and Leopard? I can't open any files ("the document blabla couldn't be opened"), nor can I create a new library ("Failed to create library").
Anyone any ideas if this is fixable?

Fixed the problem. Originally I had no problems keeping the Endnote files wherever I liked, however it now only works with the Endnote files in Users/Library. A bit weird, but I can live with it.

I lost power to my MacBook Pro before I had saved anything that I was working on...usually I plug my computer it and power it back on and the documents pop right back up when the computer turns on. That did not happen this time.How can I recover this data

I lost power to my MacBook Pro before I had saved anything that I was working on...usually I plug my computer it and power it back on and the documents pop right back up when the computer turns on. That did not happen this time. How can I recover my documents?

If you never saved, auto save does not kick in.
Peter

Can I run Tiger and Leopard on the same computer

Hi folks.
I've been meaning to install Leopard for ages but have never got round to it (I bought the retail box when it first came out). I have upgraded my RAM to 2GB and my hard drive to 320GB with no problems.
My upgraded hard drive has been partitioned into 2 equal parts of 160GB. These appear on desktop as Mackintosh HD1 and HD2. HD1 is the disk with all my files, music, OS etc and HD2 is empty
I have 2 bootable clones of my present system - one is on a 160GB external and the other is the original 80GB HD that I replaced.
My question is this - can I install Leopard on to my 160GB external HD, then clone it on to the empty HD2. If I do this would I be able to run both Tiger and Leopard on the same Macbook?
Is there any problems with this plan? Would I be able to transfer between the 2 OS and how do I install Leopard on the external drive. Is it just a case of inserting the Leopard DVD and choose the external drive as the target?
As usual thanks in advance
Del

# Original Tiger in the internal HD, New Leopard in the external HD.
# New Leopard in the internal, Legacy cloned Tiger in the external.
# Split internal, one partition with Tiger, another with Leopard.
Leopard is backwardly compatible with older Macs, just make sure yours fulfills the minimum system requirements, both use the same filesystem format, so each can see the other. You can't run both at the same time, unless you purchase the server version of Leopard and run it virtualized. 99.9% of Firewire external HD's are bootable, some USB's are bootable but have to test first. You can choose which system to boot from by pressing the Option key at boot time, before the chime. Just make sure the external HDD is plugged in and turned on if that's where you want to boot from.
When I migrated my PBG4 from Panther to Tiger, got an external FW HDD, cloned Panther onto it, upgraded using Archive and Install, cleaned up, customized and tested it. When I was satisfied all was ok, cloned the original Panther onto another partition of the external HDD, wiped and tested for failure the internal HDD, then cloned the known good and tested Tiger into it. Only thing that died along the way was my old and ancient Photoshop v2.x, that refused to run on Tiger.

I have an older Power Mac G5 Quad, and my video card just went out. I am trying to find a video card that will work for my Power Mac. I have duel screens but I can't seem to find the appropriate video card

I have an older Power Mac G5 Quad, and my video card just went out. I am trying to find a video card that will work for my Power Mac. I have duel screens but I can't seem to find the appropriate video card. The serial number on my computer is: RM620603R6W. Apple won't help me because the computer is older than suggested. Please give me the exact video card that will work best for my computer.

Hi Mike, make sure the card has Mac ROM, or is a PC card with Mac ROMs flashed to it...
G5 PCIe options are listed here:
http://www.jcsenterprises.com/Japamacs_Page/Blog/71BBF3EF-9713-4C53-8B80-26771F8 A4087.html

I just dropped my iphone and the power botton stopped working and the screen went black i allready tried to connect it to the computer and nothing what can i do

my iphone fell on the floor and the power botton wont work and also the screen went black i already tried to reset it throun itunes but the phone did not connect and i dont know what to do

You can take it to Apple and get replaced as long as you pay for the replacement.
Allan

HP Laptop Power Cord Safety Recall and Replacement

Some power cords for HP and Compaq and mini notebook computers sold from September 2010 through June 2012 may be part of voluntary recall and replacement program launched on August 26, 2014.
The impacted power cords have the potential to overheat, posing a fire, and burn hazard.
To see if your cord may be affected, look for a “LS-15” marking molded into the connector that plugs into the AC adapter.
If you see a LS-15 marking please go to http://www.hp.com/support/PowerCordReplacement
Please note that there are two parts needed to charge your laptop.
1) The first part is the power cord that plugs into the wall.
Figure 1
2) The second part is the adapter.
Figure 2
HP is ONLY recalling the power cord used with HP and Compaq notebooks and mini notebooks and accessories such as docking stations. (See Figure 1)
To qualify your power cord and request and replacement, go here.
Since power cords for laptops are compatible, you can use another power cord with your AC adapter until the replacement one arrives.
I work for HP, supporting the HP Experts who volunteer their time and technical knowledge to help others.

Does HP really expect us to individually validate every single laptop in our fleet to see if the cord that originally shipped with the machine is included in the recall? That's putting your customers through a lot of hoops to resolve an issue that could result in a safety hazard.
Also, and as you yourselves point out in the bulletin, these cords are completely interchangable, and there's no guarantee that the cord in use on the machine is the one that shipped with it.
Please provide an easier method to determine if these cords are affected by the recall. Thanks.

I have a 2.4GHz DP Power Mac G5(ppc) and want to know if buying a new graphics card

I need an editing computer and don't have the money to buy a new $1500 or so system. I have a 2.4GHz DP Power Mac G5 (ppc) and want to know if it would be worth buying a new graphics card and more RAM. I'm looking at around a $300 or so upgrade. I am saving for a new computer but need a computer to edit videos for a job I have NOW. I am currently editing on a intel core duo laptop with 6 G of RAM, the computer is taking a real beating and would also like to know if the upgrade would make the G5 run faster than the laptop I am using now.

Hello,
It won't make the G5 run much faster, but we need more info please.
At the Apple Icon at top left>About this Mac.
Then click on More Info>Hardware>Graphics/Displays and report like this...
NVIDIA GeForce 7800GT:
Chipset Model:    GeForce 7800GT
Type:    Display
Bus:    PCI
Slot:    SLOT-1
VRAM (Total):    256 MB
Vendor:    nVIDIA (0x10de)
Device ID:    0x0092
Revision ID:    0x00a1
ROM Revision:    2152.2
Displays:
VGA Display:
Resolution:    1920 x 1080 @ 60 Hz
Depth:    32-bit Color
Core Image:    Supported
Main Display:    Yes
Mirror:    Off
Online:    Yes
Quartz Extreme:    Supported
Display:
Status:    No display connected
And which exact G5 please.
At the Apple Icon at top left>About this Mac.
Then click on More Info>Hardware and report this upto *but not including the Serial#*...
Hardware Overview:
Machine Name: Power Mac G5 Quad
Machine Model: PowerMac11,2
CPU Type: PowerPC G5 (1.1)
Number Of CPUs: 4
CPU Speed: 2.5 GHz
L2 Cache (per CPU): 1 MB
Memory: 10 GB
Bus Speed: 1.25 GHz
Boot ROM Version: 5.2.7f1
Also, Graphics cards are slim pickings for G5s.

Power PC G-5 and Leopard

Similar Messages

Maybe you are looking for