Power Supply is not working in Germany

Hi, I bought long time ago a notebook in USA. When I was back in Germany the notebook didn't charged any more. I asked for support, because of the guarantee, but they said there guarantee is for supplies only six month. I forgot the notebook in the cellar. Now I'm asking myself, if the is a possibility to get a "new" notebook running. I just used the notebook 2 hours. Thanks and regardsMosesKama P.S: I wouldn't recommend the service in Germany to somebody. I wrote them before months and I'm still waiting for a feedback.  

MosesKama wrote:
Do you know about any possiblities to get run a notebook that a bought in the Staates, but like to use ist in  Germany.The notebook is not charging. ThanksDid you check with HP support if the chargers are of different voltages standards which may require different chargers?

Similar Messages

  • My MagSafe Charger / Power Supply is not working

    I am using mid 2009 13" MacBook Pro with 85W MagSafe  . My operating system is Lion 10.7.4.
    I heard a "click" coming from the direction of where my charger and just before and now its not working.
    The light is not coming on the charger itself
    No power is shown be coming into the computer on the Desktop toolbar either, nor does my computer that there's a charger plugged in.
    I have tried the charger in a number of the different sockets around the apartment and still no joy
    The transformer "block" is cold
    Could this be a s simple as a blown fuse in the plug or something else altogether?
    I need to fix this asap. No power = no computer. All help much appreciated.

    I've copy and paste info from under AC. The MagSafe charger is physically connected, the report says that is not connected and not charging.
    Any tips on where I can get cheap new Apple charger (60W MagSafe)?  Thanks to you
    both.
    Battery Information:
      Model Information:
      Serial Number:          9G9460Q108VNC
      Manufacturer:          DP
      Device Name:          bq20z451
      Pack Lot Code:          0
      PCB Lot Code:          0
      Firmware Version:          3
      Hardware Revision:          2
      Cell Revision:          100
      Charge Information:
      Charge Remaining (mAh):          1669
      Fully Charged:          No
      Charging:          No
      Full Charge Capacity (mAh):          4936
      Health Information:
      Cycle Count:          507
      Condition:          Normal
      Battery Installed:          Yes
      Amperage (mA):          -2244
      Voltage (mV):          10881
    System Power Settings:
      AC Power:
      System Sleep Timer (Minutes):          180
      Disk Sleep Timer (Minutes):          0
      Display Sleep Timer (Minutes):          15
      Wake on AC Change:          No
      Wake on Clamshell Open:          Yes
      Wake on LAN:          Yes
      Display Sleep Uses Dim:          Yes
      PrioritizeNetworkReachabilityOverSleep:          0
      RestartAfterKernelPanic:          157680000
      Battery Power:
      System Sleep Timer (Minutes):          15
      Disk Sleep Timer (Minutes):          10
      Display Sleep Timer (Minutes):          3
      Wake on AC Change:          No
      Wake on Clamshell Open:          Yes
      Current Power Source:          Yes
      Display Sleep Uses Dim:          Yes
      Reduce Brightness:          No
      RestartAfterKernelPanic:          157680000
    Hardware Configuration:
      UPS Installed:          No
    AC Charger Information:
      Connected:          No
      Charging:          No

  • Satellite L650-1P4 - AC power supply is not working

    I have a problem with my computer:
    When I plug in the AC adapter to the computer, the computer did not work and the battery is no longer supported but computer works with battery and the charger works on another pc.
    +Message was edited: posting has been translated+

    I have a problem with my computer:
    When I plug in the AC adapter to the computer, the computer did not work and the battery is no longer supported but computer works with battery and the charger works on another pc.

  • HT1547 My mac book pro is 3 yrs old and today while watching something on it, it got power off suddenly. And power button is not working, left side round button to battery is not working but when I plugg in to charge it, then this round button shows 4 gre

    I am having MacBook Pro 3 yrs old and today while I was watching some movie on it suddenly it got power off and when I am trying to start it, it's power button is not working even the round button on external left side is not showing battery lights. But when I connect it to chrger then Charger only gives green light and even the external round button only shown 4 green lights (if charger connected). I don't know what to do now

    Sounds like you need a #1SMC Reset
    1. SMC reset
    >>Instructions to reset SMC
    Disconnect other non-Apple and external hardware except (if applicable) a mouse and keyboard until your finished repairing your machine.
    Problems solved: Fans blowing with no activity, machine is not booting, power button pressed and nothing happens, problems with indicators, Magsafe has wrong lights, battery is not charging, monitor and graphics issues etc.  If the battery is not charged (from like letting it sleep too long), let the Mac charge up awhile afterwards.
    Will not hurt the machine resetting if it's not broken.
    Other related hardware problems (optional):
    Check battery status: Hold option/alt key down while clicking on the battery icon in the menu bar, top right corner.
    Magsafe: Use the correct/matching power supply charger with your Mac, not a less powered one from another Mac.
    Apple: Laptop won't power up   Apple: Computer won't power up  Troubleshooting optical drive
    Magsafe problems   Magsafe problems more

  • Dead B&W G3 ? Only the power supply seems to work...

    Hi Everyone...
    Here's my setup:
    Powermac G3 B&W Rev.B
    Processor: Powerlogix G3 750FX (1Ghz)
    Ram: 1GB (4x256Mb)
    OS 10.4.9 (latest OS supported by Powerlogix)
    HD: IBM desktar 120MB
    DVD-Rom: Samsung DVD-/+R
    PCI 66Mhz -> Radeon 9200
    PCI 33MHZ -> M-Audio 2496 Audiophile Audio Card
    PCI 33MHZ -> Sonnet Tango 2.0 (USB/FW)
    PCI 33MHZ -> Sonnet Tempo ATA133 (my main drive uses this card)
    The B&W G3 has been one of my hobby machine for a year (I mostly use it as a jukebox to listen to AIFF disc images in PCM / uncompressed sound).
    Anyway... it died on Saturday night... just after upgrading to a Sonnet Tempo ATA 133 card...
    As I've been a Mac user for a long time (and I've been there before with a Gossamer MB in my beige G3 which died out of the blue once), I completely did empty the motherboard... adding one element at a time to isolate the issue but the fact is that:
    a) no startup sound
    b) black screen (nothing comes out of the Radeon 9200)
    c) only the power supply seems to work
    d) even when plugging the HD into the MB IDE socket, the HD doesn't even activate itself (no boot).
    Of course, I went through the CUDA switch, tried to reset the PRAM, checked the jumpers on the HD (master position)...
    I also tried to boot the system off the OSX Tiger Install DVD but nothing...
    I have a feeling that my MB may be DOA.
    What do you think ?
    If this is the case, since I'm using a Tempo ATA 133 PCI Card, does it make any difference to replace it with either a REV.A or B MB ?
    Thanks for your help,
    Pierre André.
    Message was edited by: pierreandre90403

    Hi Grant,
    I posted the following on another thread, but I haven't gotten any response.
    I'm having a similar problem with a B&W 350 MHz (rev 1 I think). I get the start up tone and nothing appears on the monitor. Not sure if the machine is actually booting or not.
    I am trying to repair this machine for a friend. They had been having a problem with the machine booting into a blue screen. I suspected a corrupt directory, so I ran Disk Utility (from another machine) and also Disk Warrior. Both Disk Utility's Disk Repair feature and Disk Warrior found problems. Disk Warrior was able to successfully rebuild the directory.
    I had removed the hard drive from the machine and put it in an external casing in order to run Disk Repair and Disk Warrior. Upon putting the hard drive back into the B&W and booting the machine, I was able to successfully boot the machine into Tiger. I tested the machine for a few minutes and it seemed to work fine.
    Next, I ran software update and installed a new version of Safari and then after the required re-boot, tried to repair disk permissions. During the repair of disk permissions, the machine froze up completely. The clock stopped ticking and there was no mouse or keyboard response. I tried using the re-boot button on the front of the machine, but the machine would not fully re-boot. I get a boot tone, but no video.
    I tried re-setting the CUDA chip by pressing the re-set button on the logic board, but to no avail.
    Finally, I did take the battery out and had it tested at Radio Shack. The battery is showing a good 3.6 volts.
    I have a second B&W (300 MHz) that is basically doing the same thing. Do you know what could be causing the lack of video signal?
    Cheers,
    Thomas
    PS: I tried re-setting the logic board as described in another post (unplugged machine, pressed power button, removed battery, waited 10 minutes). I have tried the CUDA reset several times, but I only press the button for a second, not 15 seconds. I have re-seated the RAM. I have removed all the RAM and tested each. Nothing seems to work.

  • T440p Fingerprin​t power-on is not working

    Hi , i just recieved my new T440p ,  Fingerprint @ power-on is not working although all config. is done typically in lenovo fingerprint manager pro & fingerprint security settings in the BIOS , i start my laptop it goes through windows normal startup & logon without any request for fingerprint .
    Solved!
    Go to Solution.

    Dear Ahmad
    Welcome in lenovo community
    Have you tried to first to enroll your fingers first , an application called Lenovo Think Vantage should be installed .
    Do you have this application installed ?
    Also you need to check the device manager , it's better to send us a screen shot of it .
    Let us know
    Thanks
    Alaa
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Froze on black screen and power button does not work

    my sons ipod touch is stuck on a black screen when plugged into the computer got a spinning wheel and will not connect now spinning wheel will not go away the power button does not work so can not reset it manually
    any suggestions would be appreciated

    - iOS: Not responding or does not turn on
    Neglect the reset and when it says place the iPod in recovery mode use one of thes programs
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer          
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • Is there anyway to power off an I-phone 4s if the power button is not working?

    Is there anyway to power off the phone if the power button is not working?

    Assistive Touch. Tap Settings App > General > Accessibility > Assistive Touch > ON > at bottom of screen tap button > Device > press and hold Lock Screen icon > when slide to power off appears > slide it. To turn iPhone ON connect to Power Source with USB cable, charger or USB port of computer.
    All iPhone 4S have full Warranty Coverage. Make Genius Reservation and take iPhone to Apple for resolution.

  • I have unabled 5 fingure gesture now not able to perform any task,also my power button is not working,please help me in removing this gesture,using I phone 4

    I have unabled 5 fingure gesture now not able to perform any task,also my power button is not working,please help me in removing this gesture,using I phone 4

    I have unabled 5 fingure gesture now not able to perform any task,also my power button is not working,please help me in removing this gesture,using I phone 4

  • My laptop keyboard is having problems. I took it if to change my bottom case it worked fine prior and then after just the power key worked. I cleaned everything nothing is bent in the cable. now my power key is not working

    Hi my keyboard is not working I took off the bottom case to change it prior my keyboard was fine and after just the power key worked. I checked everything no portions were bent and it plugged in good. I tried to turn it on this morning and now the power key doors not work??

    Back up all data.
    Triple-click anywhere in the line below to select it:
    pmset -g assertions
    Copy the selected text to the Clipboard (command-C).
    Launch the Terminal application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
    Paste into the Terminal window (command-V).
    Post any lines of output that appear below what you entered — the text, please, not a screenshot.

  • My ipad has a black screen and the power button is not working. Help!

    This is the second time my ipad screen has gone black. The power button is not working. I reset the ipad about two weeks ago  when this happened. However, this time I am not able to get itunes to recognize the device. It keeps asking to respond from the ipad (obviously with a black screen that isn't going to happen). Im not sure what to try next...thoughts?

    Have you tried to give it a reset?
    Reset
    Hold down the sleep and home keys for about 20 seconds. When you see the silver apple, let go and let it reboot. No data will be lost.

  • How can i restart my phone if the power button is not working?

    My power button is not working and my phone freezes every now and them. I read I should restart it. Is there another way to restart it without using the power button?
    Also, I use the on-screen assistance icon but it does not have a power off option.

    demeece wrote:
    My power button is not working and my phone freezes every now and them. I read I should restart it. Is there another way to restart it without using the power button?
    Also, I use the on-screen assistance icon but it does not have a power off option.
    That's correct.  Because how would you turn it back on again if the screen was off and your power button was on the screen?
    Yo need to fix the button, or try letting the iPhone die out completely, then connect it to power and after it's charged for a while, see what happens when you press the Home button.

  • My iphone power button is not working. What can I do?

    Hello, I bought an iphone 5 last year and it still in warranty . It has some regular scratches for the use but it never felt down.
    The power button is not working now and I sent to an apple retailer here in Brazil (SOMA - Revenda APPLE Solution Expert e Assis. Tecnica Autorizada) to fix it. They refuse to do it saying that the button is not working because of  the scratches what I believe is not true. And the retailler suggest to me to buy a new one.
    And more, I receive the iphone with the factory configuration and I don’t know why.
    I would know what can I do to fix the iphone. And How can I use the warranty here in Brazil.
    I couldn't find an e-mail from apple.com support to report this.
    I will stay in US next december. I can fix my phone in an Apple Store?
    I'm very dissapointed with the technical assistance here in Brazil.
    Thank You

    Meaning that you cannot restart or reset the phone?  If you haven't tried already, try both options.
    Otherwise, you can do a backup & restore, or even a restore as new (only after a successful backup).
    If the issue persists, then look at a replacement. Either it will be a hardware defect (free if within warranty), or physical damage ($49 with AppleCare Plus, $149 without it.)

  • Ac power adapter is not working

    i bought this item apox. 9/10 months ago from Tesco so i dont know if i have any cover?
    HP Photosmart Plus All-in-One Printer - B209a
    ac power adapter is not working and i ready own hp printers and dont want to have to splash out on another.
    please help... 
    This question was solved.
    View Solution.

    Hi,
    You should still be under warranty, but if not you should be able to buy one from HP Parts Surfer.
    I hope this helps
    JonW
    I work for HP

  • HT4623 Hi I have a question, I am operating my iPhone 4S on 6.1.1iOS, as my power button is not working, I have jailbreoked my device so that I have a option to restart and shutdown my device. If i upgrade to iOS 7 do i have such option?

    Hi I have a question, I am operating my iPhone 4S on 6.1.1iOS, as my power button is not working, I have jailbreoked my device so that I have a option to restart and shutdown my device. If i upgrade to iOS 7 do i have such option?

    Jailbreaking your iPhone forfeits your ability to receive any support on that phone, including from this forum.
    You'll have to search elsewhere for answers to your issue.

Maybe you are looking for