Powerbook crashes with DSL modem voyager 105

Hi,
I use a Voyager 105 USB modem for broadband access. About every second or third time I use this, my Powerbook crashes with kernel panic and requires a reboot. Any ideas how to solve that?
Thanks.
Gernot
Powerbook 12 Mac OS X (10.4.5)

As suggested by Daniel and Gareth, USB modems like the Voyager can be prone to driver issues. Problems can sometimes be resolved through updated drivers from the manufacturer.
However the best way to resolve the problem is to invest in an ethernet modem/router instead as these do not require any drivers. Most of them also allow you to share the internet connection with other computers on the network.
Assuming you are UK-based, there are many vendors who can supply perfectly capable ethernet-based products for comparatively low cost. Amongst them are ADSL Nation and DSL Source (I have no affiliation to either of them except being a customer).
You can also get further information on ADSL products and services from ADSLguide, which also has a dedicated Apple section (with some very helpful and knowledgeable people) on their discussions forum.
15 1.25G/12 1G PBs, Mac minis, iBooks G3/G4, Mac OS X (10.4.3) Cube, TAMs, iPods 2G/4G, iPs, AEBS, AX

Similar Messages

Trouble using Airport Express Base Station with DSL modem, Router and Hub

About 18 months ago, I had an Airport (802.11b) with WAN & LAN ports and modem hooked up to support two laptops, a Titanium Powerbook G4/600 and G3/400. The setup went from DSL modem -> Linksys router -> to Airport -> Hub (which had desktop and ethernet laser printer plugged in). The network worked fine.
Then, I got a G4 iBook to replace G3/400. Wanted to get 802.11g to support “g” Airport card in iBook. Got a Linksys 802.11g Wi-Fi with 4-port router for $50. Hooked it up directly with DSL modem. (Couldn’t get it to send out to hub). Hooked the desktop and ethernet laser printer into Linksys Wi-Fi/router. The only way I could use the printer was by having it be a shared printer from the desktop. This was often problematic.
Two months ago, I got a refurbished Airport Extreme Base Station. I can’t get the AEBS to interface directly with the DSL modem, so I hooked it up as follows:
DSL modem -> Linksys router -> to AEBS -> Hub. I plugged my Epson 820 (USB) into the AEBS and can see it to print to.
I have a static IP. That info is entered into Linksys router. Router set as Gateway, with DHCP enabled. AEBS is set to Connect using Ethernet, Configure using DHCP. Network setting: Distribute IP Addresses is unchecked.
Here’s my issue:
I can’t see the ethernet laser printer. It will occasionally flash available, but is gone in less than a minute. The printer is HP 2100 series.
Sometimes I can connect to the desktop G4 tower; most times I can’t.
I have checked and double-checked the cables.
Both the printer and desktop are connected to the Hub.
What can I do so that I can see the HP 2100 series printer and the G4 tower?

Don,
Thanks for the suggestions. Glutton for punishment that I am, I tried this again, “just for grins.“ The six other times I tried this, I couldn’t get the AEBS to “see” the Internet. And lo, this time it worked. Here’s the setup now:
DSL modem -> AEBS -> 4-port hub (which is connected to G4 tower and HP 2100 Ethernet printer). My USB Epson is connected to the AEBS, and I can print from the laptops. AEBS is set up: manual IP info, Network: distribute IP address; share a single IP using DHCP.
When I still couldn’t see the desktop G4 and the Ethernet HP 2100 connected via the hub (not), I got a flash. I had swapped out the cable a number of times to no avail. Then I realized, the hub is old and all the cables I was using are the new CAT5s. I dug out an old four-wire with RJ45 connectors that my husband made years ago (probably a cross-over cable). It was quite an effort as the cable is 30 ft. long and wrapped around the perimeter of the office behind desks and file cabinets, entwined with all the other wires. But I plugged it in and, Shazam! I am WORKING!
And, Don, thanks to you, I have eliminated the router from my gaggle of electronic boxes.

Best Router with DSL Modem for use with AT&T DSL and Airport Express?

I recently had my old 2WIRE from AT&T DSL service die, so purchased a new 2WIRE 2701HG-B. My old 2WIRE worked with my Airport Express, which is hooked up to my DVR for DirecTV use. The new 2WIRE apparently is not compatible with the Airport Express, so I returned it and purchased a NetGear Wireless-N 300 Router with DSL modem. While this one does work with the Airport Express setup, it runs very slow. This router has mediocre reviews, so I'd like to find a better one.
I'd appreciate any suggestions for a Router w Modem that would work best with my AT&T DSL and Airport Express (802.11n) within the $100 - $150 price range. Thanks!

Configure the Express as a bridge: Connect via "Ethernet", and set Connection Sharing to "off (bridge mode)".
The switches ought not to be a problem, and I don't know why your router froze. The Express is simply another wired client, just like a computer might be.
do I turn off DHCP on the router,
No. Something has to provide routing functions so leave the Linksys alone.

Airport Expess with DSL Modem Router

I had a DSL Modem Router with 3 computers plugged into it via ethernet and was working fine. I then replaced one of my computers with a laptop so bought an AE and plugged it into an ethernet port on the DSL modem router. It worked fine for about 4 days then all three computers internet connections went down. I have got the two desktops working again with the AE disconnected but am worried that if i connect the AE again the same thing will happen. Is there any way that i can avoid this from happening? is this because i am doubling up the routing if you know what i mean?
MacBook Pro 17" Mac OS X (10.4.7)

First welcome to the discussions,
This isn't that uncommon, many of us expieriance drops in service and have to reset our systems.
There could be any number of reasons that cause this from a Power Spike to surges from power company, to storms from wind and lighting.
If you are lucky nothing gets fried and a simple reset will take care of the problem. Other times it can fry about any component and sometimes it's hard to find exqactly what is fried. If you are able to reset and get everything up and running again I wouldn't worry to much, I would consider a Battery Back-up to add to your Network to save your equipment though.
Cheers and Good Luck.
Don

RV110w wont connect with dsl modem for VPN

Hello,
I have bought a RV110w router and I also have a D-Link 320B DSL modem (which is replacing my standard Sky broadband router/modem) and I am having problems getting them set up correctly, firstly for the internet to work and secondly to use the VPN function on the router.
The D-Link 320B DSL modem works when connected directly into my laptop via an ethernet connection, however when I connect the modem into the RV110w the internet will not work. The dashboard on the RV110w says that the internet is "up" and gives an IP address but the internet does not work on any computer on the network. Any help here would be hugely appreciated!
After I have overcome the problem above I then want to be able to get the VPN working which I have also had no luck with.
The RV110w is set to 192.168.1.250 and the D-Link is set to 192.168.1.1. If I turn off DHCP on the D-Link I cannot then get access to the modem at all, the only way I can then get access is to hold down reset and go back to factory settings.
I have been trying to do this for about two weeks now with no luck, no matter what settings I try it just does not seem to work!!
Matt.

Dear Matthew,
Thank you for reaching Small Business Support Community.
In order to accomplish both needs, you would first need to configure the PPPoE and DHCP settings on the RV110 and set the D-Link for bridge mode only so that the xDSL negotiation is performed by the Cisco router and be the DHCP server for the LAN at the same time.
You need to first configure the PPPoE parameters on the RV110; please refer to page 23, chapter 2 of the admin guide;
http://www.cisco.com/en/US/docs/routers/csbr/rv110w/administration/guide/rv110w_admin.pdf
The required PPPoE settings are provided by your ISP and you may also copy those current settings from the D-Link modem (unfortunately I cannot tell you where they are since I am not familiar with the 320B model). You also need to set the D-Link for bridge mode since the PPPoE settings are now going to be entered on the RV110.
To set the RV110 as a DHCP server please refer to page 31, chapter 2 on the same admin guide.
You can have either a remote access VPN or a site to site VPN configured on this RV110, please check chapter 5 on admin guide. Notice for either one you would need to have static public IP addresses or a domain name provided by your ISP intended for a VPN tunnel, and in case they do provide you with neither one, then you would have to get a third party dynamic DNS service to accomplish this task. I have personally used DynDNS and it works just fine.
I hope you find this information useful and please do not hesitate to reach me back if there is any further assistance I may help you with.
Kind regards,
Jeffrey Rodriguez S. .:|:.:|:.
Cisco Customer Support Engineer
*Please rate the Post so other will know when an answer has been found.

Configure airport extreme with dsl modem

Need Help-I have a new DSL modem CenturyLink Q1000z, that is providing wireless to my home. I want to put it in bridge mode and use my aiport extreme base station(square one). Please explain how to configure it with aiport utility 6.0. I will need step by step as I cannot seem to find it in any forum. thanks

I have a new DSL modem CenturyLink Q1000z, that is providing wireless to my home. I want to put it in bridge mode
I suppose that it is possible that another CenturyLink user might have done this and will see this post...but at the same time it is also highly unlikely that this might occur.
Your best bet may be to refer to the Support Site for Centurylink for answers:
http://qwest.centurylink.com/internethelp/modems.html
Once you have the modem in Bridge Mode, you can configure the AirPort Extreme as follows using AirPort Utility 6.0:
Connect and Ethernet cable from the Centory Link modem to the WAN port (circle icon) on the AirPort Extreme
Open AirPort Utility 6.0
Click on Other AirPort Base Stations in the upper left hand corner of the window
Click on the AirPort Extreme
AirPort Utility will take a moment to analyze things and then suggest that you configure the AirPort Extreme to "Create a wireless network"
Edit the name of the Wireless Network and Base Station as you wish
Enter a Password and Confirm
Enter your user name and password for your provider's service
Leave the Service Name area completely blank
Set Connection to Always On
Click Next
When you see the message that AirPort Utility has configured your AirPort Extreme, click Done

MacBook-Apple Modem use with DSL Modem

I have a MacBook and also purchased an Apple USB Modem. Have not installed it as I now have DSL and their modem. Don't appear to be able to fax with the DSL modem, thus want to know if it's a problem installing the Apple USB Modem for faxing purposes? Is it possible and do I need to disconnect the DSL modem to do so?
<Post Relocated by Moderator>

Hi IMAC LADY!
You cannot be connected to the Internet, while you are sending, or receiving a FAX.
You must use a Dial-Up connection, to FAX.
Not all DSL Cable Modems can be configured to send a FAX using the OS X FAX function.
Review this KB Article Can I fax with my cable, ADSL, DSL, or ISDN modem using Mac OS X 10.3?.
I have DSL as well, and when I want to send or receive a FAX, I disconnect the Ethernet cable from the Mac Ethernet port, and plug a phone connection cord, from the wall jack to the Internal Modem port on the Mac.
If using an External Modem, connect to that.
I have a two port Splitter/Filter plugged into the wall jack.
The Cable/DSL Modem wire, is always plugged into one of the ports on that splitter.
When I want to use the FAX function, I plug the phone connection cord into the other port, but I do not unplug the Cable /DSL Modem.
The Splitter/Filter may not be a necessity. If you don't have one, just unplug the Cable Modem wire from the wall jack, and plug in the phone connection cord.
I then set the Network System Preferences, back to the Internel Modem, or External Modem, deselect the Built-in Ethernet, select Internal or External Modem, and drag it to the top of the window.
This of course will disconnect the Mac from the DSL connection, and you can then use the Internal Modem to send or receive a FAX.
Also review this Topic Faxing, for additional tips.
Additionally, when you enter the recipient FAX number, use this format 1-area code-xxx-xxxx.
ali b

Setting up Time Capsule as router with DSL Modem as bridge

Hi All,
I want to work this out in my head before I start disconnecting wires. So let me run down what the situation and plan is. If you see a potential issue, I would appreciate the feedback.
What I have:
Verizon DSL. The DSL modem is also doing duty as the router. For a lot of reasons I don't need to get into here, I no longer want the DSL modem to be the router. I have gotten instructions on how to setup the DSL modem to serve ONLY as a bridge. In that configuration, you simply connect the DSL modem to the phone line as usual, then connect your router to one of the ethernet ports. My time capsule has been serving only as a wireless access and backup drive until now. So here is what I plan to do:
1) Connect via ethernet cable, the WAN port on the TC to the ethernet port on the DSL modem.
2) Using the manual setup screen on the TC, select the "Internet" tab.
3) Set "Connect Using" to "Ethernet"
4) Set "Connection Sharing" to "Share a public address"
5) TCP/IP set to "Using DHCP"
At this point, everything should work. At least I think it should. Am I missing something?
Any suggestions appreciated.
Thanks,
R

I haven't worked with the Verizon gateways, but configuring the device as a simple bridge might require that the Time Capsule be setup to furnish the PPPoE service. You won't know until you try.
If you are not able to "Connect Using - Ethernet", then that would be an indication that you would need to instead "Connect Using - PPPoE". In this case, you'll need to enter your user name and password that you have established with the service provider in the Time Capsule setup configuration. Be sure to leave the Service Name area completely blank if you setup using PPPoE.
If you are able to "Connect Using - Ethernet" and you configure the Time Capsule to "Share a public IP address", you may see a warning during setup that this is producing what is known as a Double NAT on your network. This is normally not too serious, unless you are trying to setup online gaming, which requires a different type of NAT setting.

Install RVS4000 with DSL modem / router combo?

I'm trying to install a RVS4000 VPN router in our small office. My problem is that AT&T has installed a Netopia 3347-02 DSL combination Modem / router. So I can't connect the RVS4000 directly to a dsl modem, the only access I have is on the Lan side of the Netopia. When I tried to set the WAN side of the RVS4000 to the same subnet as our Lan, it wouldn't let me do that. I tried setting the Lan side of the Netopia and the Wan side of the RVS4000 to (the same) slightly different subnet, but that didn't work either. The only way I can get internet access going through both devices is to connect the Lan side of the Netopia to the Lan side of the RVS4000, but that bypasses the VPN, correct? The reason I bought the RVS4000 is for the VPN. Is there a way to configure the RVS4000 in this situation, or do I need to get a plain old DSL modem without a built in router?
Thanks, Scott

Scott,
You should not need to get another device to use the VPN functions of the RVS4000. To setup the equipment you have, you just need to place the Netopia DSL router into "bridge" mode. This will then allow you to connect the DSL router to WAN (internet) port on your RVS4000. Once in bridge mode, your WAN port on the RVS4000 will receive its IP address from AT&T, which will then take over all routing functions, and enable you to use the VPN feature of this router.
If your DSL provider is using PPPoE, you will need to select "PPPoE" on the WAN setup page of the RVS4000, then enter the username and password into the RVS4000 so that it can authenticate and get an IP address from AT&T.
To place the Netopia DSL router into "bridge" mode, I am including a link to one of their user guides. The section for placing it in bridge mode starts on page 107.
http://www.netopia.com/support/hardware/SoftwareUserGuideV761-Clsc.pdf
Thank you,
Darren

RV120 Bridged with DSL modem/router

Hello,
I am working overseas for a small company, trying to get an RV120 VPN router to connect to our network back home. Part of the problem is that I have to use a DSL modem here which is also a router, and so the WAN IP given to the modem is not the same one used by the VPN router.
Do we need to create a bridge between the two routers so that the VPN router can use the WAN IP from the ISP instead of a DHCP address on the local network? Or is this the wrong approach?
Any assistance is appreciated. I am a software engineer, not a networking/IT person so most of this is unfamiliar to me.
Thanks,
Dan

The DSL router does have VLAN capabilities, would that help? I briefly tried the DMZ solution, but didn't seem to make any progress. So when using the DMZ, would the VPN router still have an IP relative to the DSL router (10.1.1.x, etc. in this case, if the DSL router is 10.1.1.1), or should it try to takeover the actual WAN IP that the router uses?
Thanks

Can't connect to internet..self assigned ip address problem with DSL Modem

I've run into this before, without resolution, and now again on a friend's iMac. Time to ask around...
Basically, everything appears to be assigned and configured perfectly, but the network status always shows, "...you have a self assigned IP address and may not be able to connect to the internet". Sure can't connect to the net when it says that.
I've gone thru the procedure advise before that details the sequence of events needed to insure the modem resets and recognizes the Mac and it's incoming DSL (sbcglobal) signal. The order of network priority is set properly by dragging built in ethernet to the top of the list. Modem was powered down, plugged in, and then connected to the Mac, but no solution. Any ideas? thanks

This continues to be a mystery. I've had my powerbook on several networks, and connection has, most of the time, been an automatic process. Additionally, I've installed new systems for people with the same isp, and all has been well. So easy is the process, it's never been an issue. However, following explicit procedural instructions (including powering the Mac down), has proven unsuccessful on 2 different occasions.
There is little help with the isp support in India, which is where the call routes too.
The only thing I have not done is to swap out the cable at one of the locations, but the other location, which has the same issue, works fine on the iMac there. Only when I connect my Powerbook to the modem, does the "...self assigned ip address...not be able to connect to the internet" appear.
I just keep thinking there has got to be a small detail that is being overlooked.

Why does my guest's MacBook Pro crash my DSL modem?

My brother-in-law is visiting and brought his MacBook Pro running system 10.6 4. Whenever he turns on his computer and his Airport looks for my modem, he crashes my modem. I had him walk down the street and turn off his Airport. Then we tried connecting him with ethernet cable and he crashed the modem again. So, it's not specifically Airport but it is something with his computer. AT&T tech support is stumped. Any wizards here?

Take it back to the store since you just bought it, you have 3 months of free hand holding and a 1 year hardware warranty.
3 years for both with paid AppleCare.
If you want to fix it yourself, there is a list here
Step by Step to fix your Mac
Lemons occur with all products, most of the time Mac's are pretty good.

RV110w wont connect with dsl modem for VPN - HELP!

Hello,
I have bought a RV110w and also a D-Link 320B modem (replacing my standard Sky broadband router) and I am having difficulty setting them up. The D-Link modem works when connected directly with my laptop via ethernet but when connected into the WAN port on the RV110w none of the computers on my network have internet access. The RV110w dashboard says that the WAN connection is "UP" and gives an IP address?? Any help with this would be much appreciated.
After the above issue has been solved I would then like to use the RV110w VPN facility which I have been unable to set up correcty using QuickVPN. The laptop that I want as a VPN client is running Windows 8.
I have been trying to sort this for two weeks with no luck!!!
Matt.

Hi Matthew, thank you for using our forum, my name is Luis I am part of the Small business Support community. I apologize for your inconvenience; I have a couple of questions, what firmware are you running? The last firmware is 1.2.0.9 and you could download it here, are the computer connected to the RV110W receiving DHCP?
I want to have this information in order to provide better assistance.
Also I will share an article for QuickVPN, here you will find the configuration for your QuickVPN
https://supportforums.cisco.com/docs/DOC-29399
I hope you find this answer useful
Greetings,
Luis Arias.
Cisco Network Support Engineer.

Airport extreme stopped working with dsl modem was set on ppoe and changed to bridge then lost internet does not show up in utility

No internet or discovery on airport extreme after trying to resolve a conflict. Switched ppoe setting to bridge as suggested by utility got solid green light but lost everything else to include discovery in utility.

having similar problem. Internet is dropping frequently. Modem appears to work OK when I connect laptop via ethernet and configure modem to PPOE. After resetting modem to bridge mode and connecting airport, it'll work for some time but then I'll lose a connection. it'll sometimes reconnect but not always. using airport extreme as base station
recently added express as extender. connected via ethernet and appeared to work for awhile. still have drops.
then deleted extreme from network and tried to run with just express. again, worked a bit but dropped frequently.
now back to extreme as base and express as extender. with some fooling around, my Airport Utility still shows express as green. Except it's unplugged. so now airport utilitiy thinks there's a ghost router our there. any usggestions on how to clear that?
thx. mc

PowerBook crashes with power cord connected

I have just upgraded my memory. I added another 512MB to the existing 512MB. Everything runs fine until I connect the power cord. The system crashes/ freezes as aoon as the power cord is connected, and the system will not start with the power cord connected. I have tried taking out the battery and starting with just the power cord witht the same results.
This would not be such a big deal if my battery had some life left in it, at the most I can get 45 minutes before I have to recharge.

Try setting your energy saver processor speed settings to "highest" for both battery and power adapter operation. If this fixes the problem, your second ram chip is not "bus slewing" compatible. See http://discussions.apple.com/thread.jspa?threadID=227369&tstart=0

Powerbook crashes with DSL modem voyager 105

Similar Messages

Maybe you are looking for