PowerBook enters sleep mode with charger on and with new battery in Full

Hi all,
My powerbook enters in Sleep mode when it has a lot of energy. I have the powerbook with the charge on and battery in full charge and it still goes to sleep mode. It happens even when I'am working a lot with the computer. It appears that when a left my computer go to sleep over night the next day e goes a lot to sleep even when I'am working with the computer. I have tried to use just the charger, and just de battery but the error continues. I havemy power setting and it is e best performance (and it never goes to sleep in this mode).
I can only avoid this if I never put the computer to sleep, because I i put it i will start putting it self to sleep.
I have bought a new battery (7 months) and a new charger (2 month) recently, could be this the case?
What is happening to my computer?
It is my computer to ald and tired and needs to sleep a lot :/ ?
Thanks for any help!

The date only goes to 1970-01-01 if e click in power on without the battery and the AC adapter.
If I remove the battery and unplug the AC adapter e wait many minutes and put back on the battery and the AC adapter a switch the power back on the date staid the same.
I have notice one other think, some times the new battery that a bought in apple store does not charge (a have to remove the AC adapter a plug back in for it to charge), the AC adapter is correctly plug-in but it does not charge. I am begging to suspect that it is something wrong the the hardware (or the battery or the charger) sell by apple store.
Is the any place for replace bad hardware still in warranty in apple store?
What is the place to contact apple suport for this matters?
Thanks!

Similar Messages

  • X120e 0596 screen wont wake up after sleep mode until unplug it and remove the battery

    I recently purchased a Thinkpad X120e (0596) and am genneraly very happy with it however when it goes to sleep the screen does not wake up when the laptop does. when i wake it up i hear the fan spin up but the the screen remans powered off. ive tried waiting several minutes and it still doesnt wake up, ive also tried holding the power button for several (more than 5 ) seconds to force it to power off fully then start it again and the screen still doesnt wake up. the only way i can get it to work again is to make sure to unplug it and remove the battery for several seconds then i can get it to boot with the normaly expected complaints from windows after an abnormal shutdown.
    I have the latest updates from lenovo and microsoft installed including the latest firmware. I like the laptop so i would rather report the problem and provide any information neccisary to find a resolution than have to return it. Ive seen this problem with other laptops before and know its probably a  bug in the firmware thats not waking up the GPU is ther any tool i can use to provide the debuging info or any more direct way for me to report the bug I tried calling customer support and they told me they told me my only option was to return it and they could not report or record the issue.

    Same issue here, confirmed many times in linux, will likely recur at some point now that I am on windows (8).  The event log from the HAL says "The platform firmware has corrupted memory across the previous system power transition. Please check for updated firmware for your system" even after successful suspends, so who knows what happens when it fails. Since it's video-related, the problem could as well be in AMD's driver (also hinting at this is the fact the system periodically freezes when the screen is simply turned off from being idle).
    Also worth noting is the fact suspend seemed to work just fine on my system with the factory BIOS (1.08), with the issue appearing only in newer ones (the oldest one still available for download is already affected, and I am running the latest one). There are also slight differences in the issue between the legacy and UEFI boot modes, but none of them mitigate it.

  • My macbook pro 2.0 early 2011 will not go to sleep with the power source connected. only enters sleep mode when running on battery. Someone did this happen, and it could solve?

    Alo, my Macbook pro i7 2 GHz Intel Core i7 (early 2011) will not go to sleep with the power source connected. only enters sleep mode when running on battery. Someone did this happen, and it could solve?

    There is no output from that command line?   Maybe the pid changed.
    I'll repeat what I am trying to find out...
    1. You do a pmset -g on the terminal.
    2. The output from that pmset should have a line that says "sleep 0 (imposed by n)" where n is some number.
    3. The ps ax | grep n is supposed to display what the process associated with n is.
    It's the output from step 3 that should indicate what is causing you not to sleep.
    But speaking of sleep, that's where I am going.

  • MacBook starts and instantly enters sleep mode

    In the past few days I've been experiencing a reoccurring problem with my macbook pro. I press the power button, hear the startup of the drive, and then sometimes the display will turn on for a second(mostly stays off), and then enters sleep mode instantly. I can not get on my macbook unless I turn it on and let it sit for 15-20 minutes, then MAYBE the display will activate. Please help.

    Do you hear a chime at startup? How do you know it is entering sleep mode and not turning off? Does the cursor move on the screen? Here is something from another user's experience:
    I had the same issue with my 2008 iMac and Apple support walked me through the fix yesterday...
    1. Shut the computer down by holding the power button for 10 seconds
    2. Restart the computer and press shift at the same time until you see the progress bar start moving
    3. Once you reach the point where your screen goes dark and you see the cursor, type the first letter of the username for your computer, then hit Enter, then type your password, then hit Enter.
    4. After a moment, you should see the spinning beach ball
    5. Your screen should then move on to something along the lines of "Completing OSX Installation" (I can't remember the exact wording). Let it finish. After that it should go to your normal desktop and the issue should be fixed. (If your screen goes pitch black during this process, hit the space bar. I thought it wasn't working, but the screen was just sleeping).
    Apparently it's an issue with an automatic update that never quite got past the login screen.
    MacBook Pro (15-inch, Mid 2010)- Intermittent black screen or loss of video

  • Why is there a clicking sound when I close the cover and enter sleep mode?

    why is there a clicking sound when I close the cover and enter sleep mode?

    Hi katesvca,
    I too have an iPad smart cover, and all that clicking sound is is basically the standard lock sound for iOS. The Smart cover is equipped with magnets inside, and the iPad is also equipped with magnets, and when those magnets are closed together the iPad goes to sleep.
    I hope this answers your question.

  • TS1538 ipad does not come on once its unpluged from power source,it enters recovery mode when both power and home botton are pressed with usb on powersource but does not come up at all when connected to computer or out of power source

    ipad does not come on once its unpluged from power source,it enters recovery mode when both power and home botton are pressed with usb on powersource but does not come up at all when connected to computer or out of power source

    What model iPad do you have? If it's an iPad 1, the battery may have expired and needs replacement.
     Cheers, Tom

  • Mac mini keeps entering sleep mode

    Hi. I have a Mac mini that has this annoying problem where it keeps
    wanting to enter sleep mode. This problem seemed intermittent at first.
    What I notice is that my mini would enter sleep mode whenever I try to
    encode mp3. This seems reproducible. When it enters sleep mode,
    I can wake it up by pressing the power button. However, it goes back
    in sleep mode after a couple seconds after it wakes up. The only way
    I can get it out of sleep mode is to quit iTunes and eject the audio
    CD.
    Things I've tried:
    Energy Saver settings: Computer sleeps after 3 hours inactivity,
    display sleeps after 3 hours inactivity, unchecked "Put hard disk(s)
    to sleep when possible". I tried disabling energy save. No luck.
    I also tried to uncheck "Allow Nap" box in the Processor settings.
    However, it always checks this after a reboot.
    If I insert a DVD movie, I can watch it w/o any interruption.
    Anyone else seen this problem? Thanks in advance.
    Jim

    Hi Carl. I was unable to find com.apple.AutoWake.plist in my
    system. Deleting com.apple.PowerManagement.plist didn't
    help.
    I decided to try your open firmware instructions. I like the
    boot loader. It reminds me of the Sun's boot monitor.
    I did the reset-nvram, set-defaults, reset-all. It didn't
    help though.
    I don't think it is my power supply, either. The reason why I
    don't think this is the problem is I can watch DVD and listen
    to audio CD just fine. My sleep problem would only occur
    when I try to rip an audio CD. I can assure you that I draw
    plenty of power just playing a DVD movie.
    My guess is I have a power management configuration
    issue or a hardware problem. Since this has a Unix core
    underneath, I started poking around in the usual places
    for log files. I found the familiar /var/log and stumbled
    on system.log. Looking at the file, I found something
    that caught my eye.
    Aug 17 01:06:19 Jim-Fridlunds-Computer kernel[0]: Power Management received emergency overtemp signal. Going to sleep.
    Doing a 'grep overtemp system.log', I got the following:
    Aug 17 01:04:13 Jim-Fridlunds-Computer kernel[0]: Power Management received emergency overtemp signal. Going to sleep.
    Aug 17 01:04:37 Jim-Fridlunds-Computer kernel[0]: Power Management received emergency overtemp signal. Going to sleep.
    Aug 17 01:04:56 Jim-Fridlunds-Computer kernel[0]: Power Management received emergency overtemp signal. Going to sleep.
    Aug 17 01:05:37 Jim-Fridlunds-Computer kernel[0]: Power Management received emergency overtemp signal. Going to sleep.
    Aug 17 01:05:51 Jim-Fridlunds-Computer kernel[0]: Power Management received emergency overtemp signal. Going to sleep.
    Aug 17 01:06:00 Jim-Fridlunds-Computer kernel[0]: Power Management received emergency overtemp signal. Going to sleep.
    Aug 17 01:06:13 Jim-Fridlunds-Computer kernel[0]: Power Management received emergency overtemp signal. Going to sleep.
    Aug 17 01:06:19 Jim-Fridlunds-Computer kernel[0]: Power Management received emergency overtemp signal. Going to sleep.
    If you look at the time stamp, you'll see that each event
    is only a few seconds apart. This matches with what
    I was seeing. Machine goes to sleep. I press the power
    button and it wakes up and goes back to sleep. One
    big endless cycle. The only way I managed to get out
    of it is to quit iTunes and to eject the CD.
    Yes, I did install the Xcode 2 development kit that came
    with the Mini MAC OSX setup. I eventually want to write
    software for the Mac. So, I most likely installed the
    CHUD tools package that you had mentioned.
    I think the equivalent command line command for
    disabling the nap feature is 'hwprefs -v cpu_nap=false'.
    When I do that, I get the overtemp event and my mini
    goes to sleep. Zzz.
    In any case, my mini seems to be detecting false overtemp
    condition. Either I have a bad temp sensor or my power
    management overtemp threshold is set way too low. It's
    possible encoding audio CDs is enough to heat up the
    PPC core, but it happens way too fast. I'm thinking my
    temperature sensors are not set correctly. If anyone has
    schematics for the mini, it would most likely be a Dallas
    temp sensor chip. I'm not ready to open up my mini yet
    since it is still under warranty. I'll take it in the Apple
    store in Walnut Creek this weekend.
    Anyway, thank you guys for all your help. I found my
    experience on this forum to be quite pleasant. People
    here are very helpful.
    Jim

  • Lenovo thinkpad 8 not entering sleep mode when lid closed

    RECENTLY I BOUGHT THINKPAD 8. I HAVE A PROBLEM. IT CAN'T ENTER SLEEP MODE. I CLOSE THE LID AND THE SCREEN IS ON. AT POWER OPTION IT IS SELECTED WHEN I CLOSE THE LID TO GO TO SLEEP , ON BATTERY AND WHEN PLUGED IN. THANKS FOR ANY HELP.
    Solved!
    Go to Solution.

    I am not certain what you mean.  Are you saying that when you close the cover it does not sleep?  Are you certain you have a cover with the magnets that will put it to sleep?

  • Mac Pro unexpectedly enters sleep mode

    Ok so I installed Leopard last weekend on my Mac Pro and all initially went well with the install. After installation was done, software update appeared and stated I had approximately 4 downloads to install. So I had done this and prepared to reboot. Before rebooting, a window appeared stating that it needed to update the Boot cache. So I clicked on "OK" and the computer went into its shutdown sequence. When the computer reset, I noticed there was no start up chime and the system just sat there with a black screen. I thought perhaps it was updating the boot cache and it may take a while to finish. So I went afk for about an hour and came back. Still nothing. This is when I knew there was something seriously wrong with my system.
    After speaking with Apple support and trying several things to get it to boot, the support rep stated that it will need to go into the shop for repairs. I had taken it to an authorized service center and they diagnosed the problem as a bad logic board. They had replaced this and had ran their diagnostic tools on it to make sure it was running normally. They kept it overnight and ran Apple Service diagnostics in a repeating loop on the system. They had also cold booted the system 30+ times per the work order.
    After I brought it home and booted it, everything was seemingly running fine. Then I received a page from work (I'm a support rep) which required me to boot into Windows using Boot Camp to solve a client's problem. After I had done this, I booted Leopard back up and was playing around in it for a few minutes to check out some of the new features. I had then ran World of Warcraft to play a bit and to check out the performance increase in Leopard. After about 5 minutes of playing, my system unexpectedly entered sleep mode. Obviously I was confused so I had brought it out of sleep mode by hitting the enter key. The system came back for about 2 seconds and immediately went back into sleep mode again. This happened about 4 or 5 times before I finally shut the system down.
    The first thing I did after reboot is to check the energy saver options. Both hard drive and monitor energy options were set to "Never". I then checked for software updates. There was both an SMC firmware update and a Boot Camp EFI(?) firmware update. I had done the SMC firmware update first and then after successfully updating this, I had done the Boot Camp firmware update. After reboot, the system went into sleep mode on its own approximately 5 minutes after reboot. This time I had made sure NOT to run my game as I had a suspicion that this could be causing the problem. It entered sleep mode anyway unexpectedly. After waking it up again by hitting the enter key, the desktop appeared again for about 2 seconds before going right back into sleep mode. I called the service center again and they said I would have to bring it in for them to look at. Needless to say, I am NOT very pleased.
    Has anyone ever heard of anything like this happening with a Mac Pro? I had never had any problems when I was running Tiger with any application, not even my game. The service rep where I took it said it was just bad timing that the logic board went during my OS upgrade and that the two had nothing to do with each other. My brother has a Mac Pro as well and he had upgraded to Leopard. Of course his computer works fine where mine is a sleeping fool. Does anyone have any ideas or theories as to what could be causing this? More importantly, does anyone have any suggestions on how I might be able to fix this on my own? If you could please let me know, I would appreciate it. Thank you in advance for your time.

    Wow, who are you dealing with? The first time my logic board was replaced, the techs never bothered with looking at anything else as being the problem. However, when I pointed out the power supply fan problem, they focused on that being the cause of the problem and fixed just that. I was somewhat concerned as I know some of these techs do not look at other parts of the machine as potential problem causers. I was afraid that I would hook up my system only to experience the same problem as before. Luckily, that was not the case.
    I am glad that your system appears to have the same problem as mine did. I would suggest that if you take it back to them again for a fan fix to have them run the system for about an hour after replacing it. They should be opening apps, checking the iStat widget, etc to try and make it break. If they can't after an hour or so, I think it should be ok.
    This whole ordeal makes me question the quality of parts used by Apple. My brother has an iMac G4 where the hard drive died after 2 months of getting it new. Now this issue with mine and yours with the bad logic board and the power supply fan. Who knows how many other customers report hardware related problems?

  • Computer enters sleep mode shortly after leaving sleep mode. Defect?

    I have a problem. It's not a serious problem, but since it seems to be hardware related it might cause problem in the future.
    It's pretty simple. Let's say I fold the computer screen down and leave the computer in sleep mode. If I then fold it up again it will automatically enter sleep mode once again 25-30 seconds after waking up. It doesn't matter what I do. I can be completely passive or open any app and move the cursor as much as I like. After roughly 30 seconds the screen turns black and I have to press a key to wake it up.
    It never enters sleep mode any other time if I don't choose so, it's always after being in sleep mode already. And it happens 80-90% of the time, but I have not noticed a pattern for when it doesn't.
    Naturally my settings are in order. I just updated it today and no difference after one attempt with the new OS version.
    Any ideas?

    Sleep.
    Shutting down a Mac is never required. It is best to let it sleep, unless you are planning to not use it for a period of time considerably longer than a few days.

  • IMac beeps once before entering sleep mode

    My iMac 24 inch has started to beep once before entereing sleep mode. The LED thinks blinks whilst it is asleep, which I assume is normal. Is this indicative of a hardware fault? I understand that a single beep on startup indicates a ram problem.

    If you listen carefully, you may find this beep is
    coming from the hard drive, not the speakers (plug
    headphones in and find out if it still makes the
    beep).
    Some hard drives make this beep if they have a
    re-positioned write, which is a non-fatal error. You
    can usually reformat to re-allocate the block and
    stop the error, or you can live with it.//
    Hi
    Yes you're correct, it doesn't come from speakers. It not makes the same faint beep (rather like a heart monitor blip) when closing down and always after the screen has gone blank. I have noticed that if you put a CD-ROM in the DVD drive and its still spinning when you put it into sleep mode you don't get the sound.
    P.

  • T530 wakes up immediately after it entered sleep mode or hibernation mode.

    My brand new T530 comes with windows8, but I found a strange thing that it can 't enter sleep mode or hibernation mode, every time it will wake up immediately even I close the lid.  The battery will be ran out in several hours.
    Anybody has same problem?

    Attempt to enter sleep or hibernation, then when it wakes up right after, go to Command Prompt and run "powercfg -lastwake". It'll tell you what woke up the system.
    W520: i7-2720QM, Q2000M at 1080/688/1376, 21GB RAM, 500GB + 750GB HDD, FHD screen
    X61T: L7500, 3GB RAM, 500GB HDD, XGA screen, Ultrabase
    Y3P: 5Y70, 8GB RAM, 256GB SSD, QHD+ screen

  • All-in-one 6830 printer Does not enter sleep mode when connected to a phone line

    HP staff  help. HP all-in-one printer 6830 does not enter sleep mode when conntected to a phone line via 1-Line jack.  The Firmware is PNP1CN1521AR. On August 1, 2015,  I purchased an HP all-in-one 6830  printer and upgraded to firmware PNP1CN1521AR.When a phone line is connected to 1-Line jack of 6830, the printer will no longer enter  sleep mode and the display remains on indefinitly.Removing the phone connection either from the wall outlet or from the printer causes the sleep mode to work correctly again where the control panel display turns off after 5 minutes (or optionally  after 10 or 15 minutes).This problem was previously reported by a user and has not been resolved, see:http://h30434.www3.hp.com/t5/Other-Printing-Questions/Sleep-mode-of-Officejet-Pro-6830/td-p/4772182 The user did not receive a resolution to this problem according to the thread.
    There seems to be a  6830 printer firmware or hardware problem causing this. HP  should be able to confirm this problem on 6830 easily.
    Please advise ASAP.
    Thanks 

    It's a regular analog phone line. I've tested it with other phone lines. No difference. I have another all-in-one printer which works fine (goes to sleep mode) when plugged into the same phone line.
    The 6830 works ok in other aspects. The only problem is the sleep mode. Any 6830 with the firmware I mentioned should replicate the same result, regardless of anything else. The previous firmware to PNP1CN1521AR also created this problem according to the original report of this problem by another user.
    I'm sure there's a bug in the firmware. A subroutine in the firmware monitoring the incoming fax ringing, mistakenly, sees the voltage across the phone jack pins as an event and wakes up the printer instantly even though there's no ringing. As the previous user also suspected, there seems to be an error in the phone line voltage threshold used by the firmware. The present firmware always sees a ringing at the phone line which causes it to never stay in sleep mode.

  • 27Xi stays on displaying "no source signal" after I turn off my PC or PS4, doesn't enter sleep mode.

    I started having this issue a few weeks ago. The monitor no longer enters sleep mode for whatever reason after I turn off my devices connected to it (currently my PC via DVI and my PS4 via HDMI), it turns on and displays a box with "no source signal" and never goes to sleep. Before it displayed a box with "monitor going to sleep" for a few seconds and the panel turned off as the montor entered sleep mode. This is extremely annoying. How do I fix it? What's wrong with it? I already tried a factory reset.

    Hello, try this...
    "Try Disk Utility
    1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
    2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
    *Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
    3. Click the First Aid tab.
    4. Select your Mac OS X volume.
    5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
    http://docs.info.apple.com/article.html?artnum=106214
    Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
    (Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive & clear caches.)
    If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.
    If 10.7.0 or later...
    Bootup holding CMD+r, or the Option/alt key to boot from the Restore partition & use Disk Utility from there to Repair the Disk, then Repair Permissions.

  • Windows 10 - won't enter sleep mode

    So I updated to windows 10 roughly a week ago. I have had sleep issues from day one with it not being able to wake up if it didn't enter sleep mode properly. I ended up just remembering to hit the power button or shut the lid and that was enough to put it into sleep mode and was able to wake it after opening. I saw another user said to update the Bios driver... that was working til a windows update. Two/Three days ago windows had an automatic update and that seemed to cause the problem again. But now I cannot get it into sleep mode at all even with the power button,  closing the lid and even going to start and hitting sleep. it turns off the screen and the power light continues to just be on without blinking and the fan keeps running.  This computer is only 6 months ago and I am getting frusterated. I will probably go back to 8.1 as having to hard power down the computer can't be good for it everytime I walk away and forget to completely power it down. Does anyone have another solution I can try before I jump ship?

    I have installed all updates from Windows Update and all drivers from Toshiba US website. I can't find the Service Station for Windows 10 from Toshiba website.  I only found the one for Windows 8.

Maybe you are looking for