Powerbook G4 17" Keyboard or touchpad not working at all.

So I have this computer and it used to work perfectly until i decided to add some ram. When I did, something must have shifted and caused a short circuit at the L90 inductor, right beside the keyboard/touchpad connector. The power button still works, and the computer is FULLY usable through VNC. And with my limited knowledge in Macs I cant figure out the precise type of inductor I blew. It's a 3 Cent piece that i can see is all charred and burnt but i don't know what to replace it with.
Any help would be appreciated.
Thanks

rich420 wrote:
Well I know what the problem is. Its the actual light and connection of the battery and light, it must be loose. Because when I pinch or mess around with the bottom of my phone just under my keys(where there seems to be a piece that could disasswmble from the phone), the light comes on and stays on when I hold it tight, and it flickers and flashes when I fiddle with it.
I wish you had the foresight to tell me upfront that you knew what the problem was -- there would be a little less guessing on my part and I would be able to get straight to the point.
rich420 wrote:
Would it be a good idea to disassemble my whole BB to see if I can fix in the problem inside? Or is that a bad idea? (I don't think I can return it, its my moms old phone, I don't know how long she has had it for). Thanks guys!
I don't know if you can fix it or not... someone who has done it before might could, for sure.
For a loose battery connection? Just place a business card a folder sheet of typing paper on top of the battery, replace the battery door and see how that works.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Similar Messages

Keyboard and touchpad not working after Windows 10 update

after udating windows 10 on my probook 4440s keyboard and touchpad not working. if i press a key for 10seconds the key then shows up in the screen. and touchpad is worst. it freezes all the time barely moves. but with usb mouse it works fine

It's known that installing Windows from an external DVD drive on a Mid 2013 MacBook Air causes that the keyboard doesn't work after finishing the installation. The fix is to install Windows by using a USB drive. See > http://support.apple.com/kb/TS4599

Keyboard and touchpad not working

Good day My keyboard and touchpad stopped working all of a suuden, and I need help. My computer is Toshiba Satellite E55 A-5114, this has happened to me before but only the touchpad stopped working and it fixed whenever there was a system update, now I've updated the system and installed the recent drivers and still not working, any ideas?

Satellite E45t-A4300
There appears to be an epidemic. My guess is that a Windows update which changes a driver causes it.
So turn off automatic update and inspect them one-by-one. They are offered on the second Tuesday of each month.
Windows Update: Frequently Asked Questions
I install only those marked Important or Critical. In particular, stay away from those which change a device's driver. Get driver updates only from Toshiba.

Laptop keyboard and touchpad not working in Windows 8.1

I just upgraded my S875-S7248 to Windows 8.1 last night. At first, everything seemed to be fine. However, this morning, the keyboard and touchpad had stopped working, and nothing I've tried has fixed it. After some research, I figured out how to open the Device Manager, and the both devices are showning the infamous yellow triangle. When I click on the device, I see the message "Windows cannot start this hardware device because its configuration information (in the registry) is imcomplete or damaged (Code 19)". Both devices are PS/2 devices, and I have tried uninstalling and reinstalling the device, and updating the driver, but to no avail. In addition, I've run the Toshiba Service Station driver update, but it doesn't retrun any new updates either.
So, short of unstalling Windows 8, what can I do to fix this?
Solved!
Go to Solution.

Hi rmikereese
I had the same issue - but luckily you dont have to uninstall Windows 8 (at least I didn't need to)
Running a system restore should bring your computer before you installed the "critical updates" from Toshiba. Fortunately I had a usb mouse already installed (because like you, my touchpad was also not working)
1. Restart Computer and Sign In
Note: I had to use the on-screen keyboard option found on the Ease of Access found at the bottom left of the screen
2. Right Click on "My Computer" (aka "Computer" aka "This PC") and click on Properties
3. Click on System Protection (3rd option on the left menu)
At this point a new System Properties window will pop up already on a System Protection tab
4. Click System Restore...
5. Choose restore point --> I had an option for "Windows Update" which was a "Critical Update"
My computer reset the registry and my touchpad and keyboard began working again!
When Toshiba tells you that you have Updates (Toshiba Support Driver) IGNORE IT!
Hope this works for you!
-Joe

HP Pavilion DV 6000 Mouse/Touchpad Not Working at All PLS HELP!

I have an HP Pavilion DV 6000. When it is powered on and I log in a screen pops up showing the mousepad with a red line going through it. The mouse does not move at all. Therefore I can not recover or do anything with the computer. Has anyone heard of this????
Also, the mousepad is not locked & I have tried rebooting the computer numerous times.

Kbrandt29 wrote:
I did try a USB mouse a while back. I know it didn't work but I'm not sure what happened.
How do you reinstall drivers? Sorry I'm not completely tech-savvy.
Thanks so much for your help.
First was it a corded usb mouse or a cordless?
If it was a corded it should've auto installed drivers from Windows itself to get it up and runnig.
If it was a cordless it should have again auto installed drivers for the dongle when inserted, But the mouse may have needed paired to the dongle, Which is done by usually clicking first on the discover/matching button on the bottom of the mouse itself, then pressing on the button on the dongle itself and that should match them together.
If it was a newer cordless mouse though most are already matched at the factory so there's no need for pairing much anymore.
As for installing the drivers it's fairly simple.
If you have a drivers and application DVD either that you bought from HP, or made yourself if you did a default factory image onto a DVD when you first got your computer, put that disk in your drive and navigate it till you find the driver, It should be marked Input Device Driver.
Or you can go to HP's Support Site and download the latest driver for your TouchPad and reinstall it from there.
You'll most likely have to reboot after doing this?
Let me know if this helps.
If not I've a couple other ideas, I just don't want to overwhelm you at this point.

[Solved]Synaptics Touchpad not working at all on Fujitsu Siemens UH552

Hi,
I have just installed Arch on my Fujitsu Siemens UH552 laptop. Everything works except for the touchpad which seems to get loaded by Xorg, but when in X it doesn't work. I have tried both using /dev/input/event* and /dev/input/mouse0 as device paths, neither works.
xf86-input-evdev and xf86-input-synaptics are installed.
I have tried running both with the default 10-evdev.conf, with 10-synaptics.conf, with both, and without both.
TLDR SOLUTION: https://bbs.archlinux.org/viewtopic.php … 3#p1189603
My current 10-synaptics.conf:
Section "InputClass"
Identifier "Touchpad Catchall"
MatchIsTouchpad "on"
MatchDevicePath "/dev/input/event*"
Driver "synaptics"
Option "TapButton1" "1"
Option "TapButton2" "2"
Option "TapButton3" "3"
EndSection
Xorg.0.log
[ 2275.127]
X.Org X Server 1.12.4
Release Date: 2012-08-27
[ 2275.130] X Protocol Version 11, Revision 0
[ 2275.131] Build Operating System: Linux 3.4.8-1-ARCH x86_64
[ 2275.132] Current Operating System: Linux corvo 3.5.3-1-ARCH #1 SMP PREEMPT Sun Aug 26 09:14:51 CEST 2012 x86_64
[ 2275.132] Kernel command line: root=/dev/sda2 rootflags=subvol=__active ro initrd=/boot/initramfs-linux.img BOOT_IMAGE=/boot/vmlinuz-linux
[ 2275.134] Build Date: 27 August 2012 08:04:39AM
[ 2275.135]
[ 2275.136] Current version of pixman: 0.26.2
[ 2275.138] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 2275.138] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 2275.142] (==) Log file: "/var/log/Xorg.0.log", Time: Sat Sep 1 13:16:01 2012
[ 2275.143] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 2275.144] (==) No Layout section. Using the first Screen section.
[ 2275.144] (==) No screen section available. Using defaults.
[ 2275.144] (**) |-->Screen "Default Screen Section" (0)
[ 2275.144] (**) | |-->Monitor "<default monitor>"
[ 2275.144] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[ 2275.144] (**) | |-->Device "Intel Graphics"
[ 2275.144] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 2275.144] (==) Automatically adding devices
[ 2275.144] (==) Automatically enabling devices
[ 2275.144] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 2275.144] Entry deleted from font path.
[ 2275.144] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 2275.144] Entry deleted from font path.
[ 2275.144] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 2275.144] Entry deleted from font path.
[ 2275.144] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 2275.144] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 2275.144] Entry deleted from font path.
[ 2275.144] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 2275.144] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/
[ 2275.144] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 2275.144] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 2275.144] (II) Loader magic: 0x7c8b00
[ 2275.144] (II) Module ABI versions:
[ 2275.144] X.Org ANSI C Emulation: 0.4
[ 2275.144] X.Org Video Driver: 12.1
[ 2275.144] X.Org XInput driver : 16.0
[ 2275.144] X.Org Server Extension : 6.0
[ 2275.144] (--) PCI:*(0:0:2:0) 8086:0166:10cf:16c2 rev 9, Mem @ 0xf0000000/4194304, 0xe0000000/268435456, I/O @ 0x00002000/64
[ 2275.144] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 2275.144] (II) LoadModule: "extmod"
[ 2275.144] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 2275.145] (II) Module extmod: vendor="X.Org Foundation"
[ 2275.145] compiled for 1.12.4, module version = 1.0.0
[ 2275.145] Module class: X.Org Server Extension
[ 2275.145] ABI class: X.Org Server Extension, version 6.0
[ 2275.145] (II) Loading extension MIT-SCREEN-SAVER
[ 2275.145] (II) Loading extension XFree86-VidModeExtension
[ 2275.145] (II) Loading extension XFree86-DGA
[ 2275.145] (II) Loading extension DPMS
[ 2275.145] (II) Loading extension XVideo
[ 2275.145] (II) Loading extension XVideo-MotionCompensation
[ 2275.145] (II) Loading extension X-Resource
[ 2275.145] (II) LoadModule: "dbe"
[ 2275.145] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 2275.145] (II) Module dbe: vendor="X.Org Foundation"
[ 2275.145] compiled for 1.12.4, module version = 1.0.0
[ 2275.145] Module class: X.Org Server Extension
[ 2275.145] ABI class: X.Org Server Extension, version 6.0
[ 2275.145] (II) Loading extension DOUBLE-BUFFER
[ 2275.145] (II) LoadModule: "glx"
[ 2275.145] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 2275.145] (II) Module glx: vendor="X.Org Foundation"
[ 2275.145] compiled for 1.12.4, module version = 1.0.0
[ 2275.145] ABI class: X.Org Server Extension, version 6.0
[ 2275.145] (==) AIGLX enabled
[ 2275.145] (II) Loading extension GLX
[ 2275.145] (II) LoadModule: "record"
[ 2275.145] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 2275.145] (II) Module record: vendor="X.Org Foundation"
[ 2275.145] compiled for 1.12.4, module version = 1.13.0
[ 2275.145] Module class: X.Org Server Extension
[ 2275.145] ABI class: X.Org Server Extension, version 6.0
[ 2275.145] (II) Loading extension RECORD
[ 2275.145] (II) LoadModule: "dri"
[ 2275.145] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 2275.145] (II) Module dri: vendor="X.Org Foundation"
[ 2275.145] compiled for 1.12.4, module version = 1.0.0
[ 2275.145] ABI class: X.Org Server Extension, version 6.0
[ 2275.145] (II) Loading extension XFree86-DRI
[ 2275.145] (II) LoadModule: "dri2"
[ 2275.145] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 2275.145] (II) Module dri2: vendor="X.Org Foundation"
[ 2275.145] compiled for 1.12.4, module version = 1.2.0
[ 2275.145] ABI class: X.Org Server Extension, version 6.0
[ 2275.145] (II) Loading extension DRI2
[ 2275.145] (II) LoadModule: "intel"
[ 2275.146] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 2275.146] (II) Module intel: vendor="X.Org Foundation"
[ 2275.146] compiled for 1.12.3.901, module version = 2.20.5
[ 2275.146] Module class: X.Org Video Driver
[ 2275.146] ABI class: X.Org Video Driver, version 12.1
[ 2275.146] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
Sandybridge Desktop (GT1), Sandybridge Desktop (GT2),
Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1),
Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+),
Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2),
Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server,
Ivybridge Server (GT2), Haswell Desktop (GT1), Haswell Desktop (GT2),
Haswell Desktop (GT2+), Haswell Mobile (GT1), Haswell Mobile (GT2),
Haswell Mobile (GT2+), Haswell Server (GT1), Haswell Server (GT2),
Haswell Server (GT2+), Haswell SDV Desktop (GT1),
Haswell SDV Desktop (GT2), Haswell SDV Desktop (GT2+),
Haswell SDV Mobile (GT1), Haswell SDV Mobile (GT2),
Haswell SDV Mobile (GT2+), Haswell SDV Server (GT1),
Haswell SDV Server (GT2), Haswell SDV Server (GT2+),
Haswell ULT Desktop (GT1), Haswell ULT Desktop (GT2),
Haswell ULT Desktop (GT2+), Haswell ULT Mobile (GT1),
Haswell ULT Mobile (GT2), Haswell ULT Mobile (GT2+),
Haswell ULT Server (GT1), Haswell ULT Server (GT2),
Haswell ULT Server (GT2+), Haswell CRW Desktop (GT1),
Haswell CRW Desktop (GT2), Haswell CRW Desktop (GT2+),
Haswell CRW Mobile (GT1), Haswell CRW Mobile (GT2),
Haswell CRW Mobile (GT2+), Haswell CRW Server (GT1),
Haswell CRW Server (GT2), Haswell CRW Server (GT2+)
[ 2275.146] (--) using VT number 7
[ 2275.149] drmOpenDevice: node name is /dev/dri/card0
[ 2275.149] drmOpenDevice: open result is 7, (OK)
[ 2275.150] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
[ 2275.150] drmOpenDevice: node name is /dev/dri/card0
[ 2275.150] drmOpenDevice: open result is 7, (OK)
[ 2275.150] drmOpenByBusid: drmOpenMinor returns 7
[ 2275.150] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
[ 2275.150] drmOpenDevice: node name is /dev/dri/card0
[ 2275.150] drmOpenDevice: open result is 8, (OK)
[ 2275.150] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
[ 2275.150] drmOpenDevice: node name is /dev/dri/card0
[ 2275.150] drmOpenDevice: open result is 8, (OK)
[ 2275.150] drmOpenByBusid: drmOpenMinor returns 8
[ 2275.150] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
[ 2275.150] (II) intel(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 2275.150] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[ 2275.150] (==) intel(0): RGB weight 888
[ 2275.150] (==) intel(0): Default visual is TrueColor
[ 2275.150] (**) intel(0): Option "AccelMethod" "sna"
[ 2275.150] (--) intel(0): Integrated Graphics Chipset: Intel(R) Ivybridge Mobile (GT2)
[ 2275.151] (**) intel(0): Framebuffer tiled
[ 2275.151] (**) intel(0): Pixmaps tiled
[ 2275.151] (**) intel(0): 3D buffers tiled
[ 2275.151] (**) intel(0): Throttling enabled
[ 2275.151] (**) intel(0): Delayed flush enabled
[ 2275.151] (**) intel(0): "Tear free" disabled
[ 2275.151] (**) intel(0): Forcing per-crtc-pixmaps? no
[ 2275.151] (II) intel(0): Output LVDS1 has no monitor section
[ 2275.152] (II) intel(0): found backlight control interface acpi_video0 (type 'firmware')
[ 2275.152] (II) intel(0): Output VGA1 has no monitor section
[ 2275.153] (II) intel(0): Output HDMI1 has no monitor section
[ 2275.193] (II) intel(0): Output DP1 has no monitor section
[ 2275.193] (II) intel(0): EDID for output LVDS1
[ 2275.193] (II) intel(0): Manufacturer: LGD Model: 371 Serial#: 0
[ 2275.193] (II) intel(0): Year: 2012 Week: 0
[ 2275.193] (II) intel(0): EDID Version: 1.3
[ 2275.193] (II) intel(0): Digital Display Input
[ 2275.193] (II) intel(0): Max Image Size [cm]: horiz.: 29 vert.: 16
[ 2275.193] (II) intel(0): Gamma: 2.20
[ 2275.193] (II) intel(0): No DPMS capabilities specified
[ 2275.193] (II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 2275.193] (II) intel(0): First detailed timing is preferred mode
[ 2275.193] (II) intel(0): redX: 0.589 redY: 0.347 greenX: 0.343 greenY: 0.555
[ 2275.193] (II) intel(0): blueX: 0.160 blueY: 0.124 whiteX: 0.313 whiteY: 0.329
[ 2275.193] (II) intel(0): Manufacturer's mask: 0
[ 2275.193] (II) intel(0): Supported detailed timing:
[ 2275.193] (II) intel(0): clock: 70.0 MHz Image Size: 293 x 165 mm
[ 2275.193] (II) intel(0): h_active: 1366 h_sync: 1402 h_sync_end 1438 h_blank_end 1476 h_border: 0
[ 2275.193] (II) intel(0): v_active: 768 v_sync: 772 v_sync_end 780 v_blanking: 790 v_border: 0
[ 2275.193] (II) intel(0): LG Display
[ 2275.193] (II) intel(0): LP133WH2-TLF1
[ 2275.193] (II) intel(0): EDID (in hex):
[ 2275.193] (II) intel(0): 00ffffffffffff0030e4710300000000
[ 2275.193] (II) intel(0): 00160103801d10780afc359658578e29
[ 2275.193] (II) intel(0): 1f505400000001010101010101010101
[ 2275.193] (II) intel(0): 010101010101581b566e500016302424
[ 2275.194] (II) intel(0): 480025a5100000190000000000000000
[ 2275.194] (II) intel(0): 00000000000000000000000000fe004c
[ 2275.194] (II) intel(0): 4720446973706c61790a2020000000fe
[ 2275.194] (II) intel(0): 004c503133335748322d544c463100ce
[ 2275.194] (II) intel(0): EDID vendor "LGD", prod id 881
[ 2275.194] (II) intel(0): Printing DDC gathered Modelines:
[ 2275.194] (II) intel(0): Modeline "1366x768"x0.0 70.00 1366 1402 1438 1476 768 772 780 790 -hsync -vsync (47.4 kHz eP)
[ 2275.194] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 2275.194] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 2275.194] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 2275.194] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 2275.194] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[ 2275.194] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 2275.194] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 2275.194] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[ 2275.194] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[ 2275.194] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 2275.194] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 2275.194] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[ 2275.194] (II) intel(0): Printing probed modes for output LVDS1
[ 2275.194] (II) intel(0): Modeline "1366x768"x60.0 70.00 1366 1402 1438 1476 768 772 780 790 -hsync -vsync (47.4 kHz eP)
[ 2275.194] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz d)
[ 2275.194] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz d)
[ 2275.194] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz d)
[ 2275.194] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz d)
[ 2275.194] (II) intel(0): EDID for output VGA1
[ 2275.195] (II) intel(0): EDID for output HDMI1
[ 2275.236] (II) intel(0): EDID for output DP1
[ 2275.236] (II) intel(0): Output LVDS1 connected
[ 2275.236] (II) intel(0): Output VGA1 disconnected
[ 2275.236] (II) intel(0): Output HDMI1 disconnected
[ 2275.236] (II) intel(0): Output DP1 disconnected
[ 2275.236] (II) intel(0): Using exact sizes for initial modes
[ 2275.236] (II) intel(0): Output LVDS1 using initial mode 1366x768
[ 2275.236] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 2275.236] (**) intel(0): Display dimensions: (290, 160) mm
[ 2275.236] (**) intel(0): DPI set to (119, 121)
[ 2275.236] (II) Loading sub module "dri2"
[ 2275.236] (II) LoadModule: "dri2"
[ 2275.237] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 2275.237] (II) Module dri2: vendor="X.Org Foundation"
[ 2275.237] compiled for 1.12.4, module version = 1.2.0
[ 2275.237] ABI class: X.Org Server Extension, version 6.0
[ 2275.237] (==) Depth 24 pixmap format is 32 bpp
[ 2275.237] (II) intel(0): SNA initialized with IvyBridge backend
[ 2275.237] (==) intel(0): Backing store disabled
[ 2275.237] (==) intel(0): Silken mouse enabled
[ 2275.237] (II) intel(0): HW Cursor enabled
[ 2275.237] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 2275.238] (==) intel(0): DPMS enabled
[ 2275.239] (II) intel(0): [DRI2] Setup complete
[ 2275.239] (II) intel(0): [DRI2] DRI driver: i965
[ 2275.239] (II) intel(0): direct rendering: DRI2 Enabled
[ 2275.239] (==) intel(0): hotplug detection: "enabled"
[ 2275.239] (--) RandR disabled
[ 2275.239] (II) Initializing built-in extension Generic Event Extension
[ 2275.239] (II) Initializing built-in extension SHAPE
[ 2275.239] (II) Initializing built-in extension MIT-SHM
[ 2275.239] (II) Initializing built-in extension XInputExtension
[ 2275.239] (II) Initializing built-in extension XTEST
[ 2275.239] (II) Initializing built-in extension BIG-REQUESTS
[ 2275.239] (II) Initializing built-in extension SYNC
[ 2275.239] (II) Initializing built-in extension XKEYBOARD
[ 2275.239] (II) Initializing built-in extension XC-MISC
[ 2275.239] (II) Initializing built-in extension SECURITY
[ 2275.239] (II) Initializing built-in extension XINERAMA
[ 2275.239] (II) Initializing built-in extension XFIXES
[ 2275.239] (II) Initializing built-in extension RENDER
[ 2275.239] (II) Initializing built-in extension RANDR
[ 2275.239] (II) Initializing built-in extension COMPOSITE
[ 2275.239] (II) Initializing built-in extension DAMAGE
[ 2275.250] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 2275.250] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 2275.250] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 2275.250] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 2275.250] (II) AIGLX: Loaded and initialized i965
[ 2275.250] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 2275.251] (II) intel(0): switch to mode 1366x768 on crtc 3 (pipe 0)
[ 2275.276] (II) intel(0): Setting screen physical size to 361 x 203
[ 2275.319] (II) config/udev: Adding input device Power Button (/dev/input/event6)
[ 2275.319] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 2275.319] (II) LoadModule: "evdev"
[ 2275.319] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 2275.320] (II) Module evdev: vendor="X.Org Foundation"
[ 2275.320] compiled for 1.12.3.901, module version = 2.7.3
[ 2275.320] Module class: X.Org XInput Driver
[ 2275.320] ABI class: X.Org XInput driver, version 16.0
[ 2275.320] (II) Using input driver 'evdev' for 'Power Button'
[ 2275.320] (**) Power Button: always reports core events
[ 2275.320] (**) evdev: Power Button: Device: "/dev/input/event6"
[ 2275.320] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 2275.320] (--) evdev: Power Button: Found keys
[ 2275.320] (II) evdev: Power Button: Configuring as keyboard
[ 2275.320] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input6/event6"
[ 2275.320] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 2275.320] (**) Option "xkb_rules" "evdev"
[ 2275.320] (**) Option "xkb_model" "evdev"
[ 2275.320] (**) Option "xkb_layout" "se"
[ 2275.355] (II) config/udev: Adding input device Fujitsu FUJ02E3 (/dev/input/event3)
[ 2275.356] (**) Fujitsu FUJ02E3: Applying InputClass "evdev keyboard catchall"
[ 2275.356] (II) Using input driver 'evdev' for 'Fujitsu FUJ02E3'
[ 2275.356] (**) Fujitsu FUJ02E3: always reports core events
[ 2275.356] (**) evdev: Fujitsu FUJ02E3: Device: "/dev/input/event3"
[ 2275.356] (--) evdev: Fujitsu FUJ02E3: Vendor 0 Product 0x6
[ 2275.356] (--) evdev: Fujitsu FUJ02E3: Found keys
[ 2275.356] (II) evdev: Fujitsu FUJ02E3: Configuring as keyboard
[ 2275.356] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/FUJ02E3:00/input/input3/event3"
[ 2275.356] (II) XINPUT: Adding extended input device "Fujitsu FUJ02E3" (type: KEYBOARD, id 7)
[ 2275.356] (**) Option "xkb_rules" "evdev"
[ 2275.356] (**) Option "xkb_model" "evdev"
[ 2275.356] (**) Option "xkb_layout" "se"
[ 2275.357] (II) config/udev: Adding input device Video Bus (/dev/input/event9)
[ 2275.357] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 2275.357] (II) Using input driver 'evdev' for 'Video Bus'
[ 2275.357] (**) Video Bus: always reports core events
[ 2275.357] (**) evdev: Video Bus: Device: "/dev/input/event9"
[ 2275.357] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 2275.357] (--) evdev: Video Bus: Found keys
[ 2275.357] (II) evdev: Video Bus: Configuring as keyboard
[ 2275.357] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input9/event9"
[ 2275.357] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 8)
[ 2275.358] (**) Option "xkb_rules" "evdev"
[ 2275.358] (**) Option "xkb_model" "evdev"
[ 2275.358] (**) Option "xkb_layout" "se"
[ 2275.359] (II) config/udev: Adding input device Fujitsu FUJ02B1 (/dev/input/event2)
[ 2275.359] (**) Fujitsu FUJ02B1: Applying InputClass "evdev keyboard catchall"
[ 2275.359] (II) Using input driver 'evdev' for 'Fujitsu FUJ02B1'
[ 2275.359] (**) Fujitsu FUJ02B1: always reports core events
[ 2275.359] (**) evdev: Fujitsu FUJ02B1: Device: "/dev/input/event2"
[ 2275.359] (--) evdev: Fujitsu FUJ02B1: Vendor 0 Product 0x6
[ 2275.359] (--) evdev: Fujitsu FUJ02B1: Found keys
[ 2275.359] (II) evdev: Fujitsu FUJ02B1: Configuring as keyboard
[ 2275.359] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/FUJ02B1:00/input/input2/event2"
[ 2275.359] (II) XINPUT: Adding extended input device "Fujitsu FUJ02B1" (type: KEYBOARD, id 9)
[ 2275.359] (**) Option "xkb_rules" "evdev"
[ 2275.359] (**) Option "xkb_model" "evdev"
[ 2275.359] (**) Option "xkb_layout" "se"
[ 2275.360] (II) config/udev: Adding input device Power Button (/dev/input/event5)
[ 2275.360] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 2275.360] (II) Using input driver 'evdev' for 'Power Button'
[ 2275.360] (**) Power Button: always reports core events
[ 2275.360] (**) evdev: Power Button: Device: "/dev/input/event5"
[ 2275.360] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 2275.360] (--) evdev: Power Button: Found keys
[ 2275.360] (II) evdev: Power Button: Configuring as keyboard
[ 2275.361] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5/event5"
[ 2275.361] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 10)
[ 2275.361] (**) Option "xkb_rules" "evdev"
[ 2275.361] (**) Option "xkb_model" "evdev"
[ 2275.361] (**) Option "xkb_layout" "se"
[ 2275.362] (II) config/udev: Adding input device Lid Switch (/dev/input/event4)
[ 2275.362] (II) No input driver specified, ignoring this device.
[ 2275.362] (II) This device may have been added with another device file.
[ 2275.362] (II) config/udev: Adding input device FJ Camera (/dev/input/event7)
[ 2275.362] (**) FJ Camera: Applying InputClass "evdev keyboard catchall"
[ 2275.362] (II) Using input driver 'evdev' for 'FJ Camera'
[ 2275.362] (**) FJ Camera: always reports core events
[ 2275.362] (**) evdev: FJ Camera: Device: "/dev/input/event7"
[ 2275.363] (--) evdev: FJ Camera: Vendor 0x10f1 Product 0x1a44
[ 2275.363] (--) evdev: FJ Camera: Found keys
[ 2275.363] (II) evdev: FJ Camera: Configuring as keyboard
[ 2275.363] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.3/3-1.3:1.0/input/input7/event7"
[ 2275.363] (II) XINPUT: Adding extended input device "FJ Camera" (type: KEYBOARD, id 11)
[ 2275.363] (**) Option "xkb_rules" "evdev"
[ 2275.363] (**) Option "xkb_model" "evdev"
[ 2275.363] (**) Option "xkb_layout" "se"
[ 2275.364] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event10)
[ 2275.364] (II) No input driver specified, ignoring this device.
[ 2275.364] (II) This device may have been added with another device file.
[ 2275.364] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event11)
[ 2275.364] (II) No input driver specified, ignoring this device.
[ 2275.364] (II) This device may have been added with another device file.
[ 2275.365] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event12)
[ 2275.365] (II) No input driver specified, ignoring this device.
[ 2275.365] (II) This device may have been added with another device file.
[ 2275.365] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 2275.365] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 2275.365] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 2275.366] (**) AT Translated Set 2 keyboard: always reports core events
[ 2275.366] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 2275.366] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 2275.366] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 2275.366] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 2275.366] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 2275.366] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 12)
[ 2275.366] (**) Option "xkb_rules" "evdev"
[ 2275.366] (**) Option "xkb_model" "evdev"
[ 2275.366] (**) Option "xkb_layout" "se"
[ 2275.366] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event8)
[ 2275.366] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "Touchpad Catchall"
[ 2275.366] (II) LoadModule: "synaptics"
[ 2275.366] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[ 2275.367] (II) Module synaptics: vendor="X.Org Foundation"
[ 2275.367] compiled for 1.12.2, module version = 1.6.2
[ 2275.367] Module class: X.Org XInput Driver
[ 2275.367] ABI class: X.Org XInput driver, version 16.0
[ 2275.367] (II) Using input driver 'synaptics' for 'SynPS/2 Synaptics TouchPad'
[ 2275.367] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 2275.367] (**) Option "Device" "/dev/input/event8"
[ 2275.367] (II) synaptics: SynPS/2 Synaptics TouchPad: found clickpad property
[ 2275.367] (--) synaptics: SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5472
[ 2275.367] (--) synaptics: SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4448
[ 2275.367] (--) synaptics: SynPS/2 Synaptics TouchPad: pressure range 0 - 255
[ 2275.367] (--) synaptics: SynPS/2 Synaptics TouchPad: finger width range 0 - 15
[ 2275.367] (--) synaptics: SynPS/2 Synaptics TouchPad: buttons: left double triple
[ 2275.367] (--) synaptics: SynPS/2 Synaptics TouchPad: Vendor 0x2 Product 0x7
[ 2275.367] (**) Option "TapButton1" "1"
[ 2275.367] (**) Option "TapButton2" "2"
[ 2275.367] (**) Option "TapButton3" "3"
[ 2275.367] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[ 2275.367] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 2275.367] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input8/event8"
[ 2275.368] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD, id 13)
[ 2275.368] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) MinSpeed is now constant deceleration 2.5
[ 2275.368] (**) synaptics: SynPS/2 Synaptics TouchPad: MaxSpeed is now 1.75
[ 2275.368] (**) synaptics: SynPS/2 Synaptics TouchPad: AccelFactor is now 0.040
[ 2275.368] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
[ 2275.368] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 1
[ 2275.368] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[ 2275.368] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[ 2275.368] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[ 2275.368] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse0)
[ 2275.368] (II) No input driver specified, ignoring this device.
[ 2275.368] (II) This device may have been added with another device file.
[ 2275.368] (II) config/udev: Adding input device PC Speaker (/dev/input/event1)
[ 2275.368] (II) No input driver specified, ignoring this device.
[ 2275.368] (II) This device may have been added with another device file.
xinput
⎡ Virtual core pointer id=2 [master pointer (3)]
⎜ ↳ Virtual core XTEST pointer id=4 [slave pointer (2)]
⎜ ↳ SynPS/2 Synaptics TouchPad id=13 [slave pointer (2)]
⎣ Virtual core keyboard id=3 [master keyboard (2)]
↳ Virtual core XTEST keyboard id=5 [slave keyboard (3)]
↳ Power Button id=6 [slave keyboard (3)]
↳ Fujitsu FUJ02E3 id=7 [slave keyboard (3)]
↳ Video Bus id=8 [slave keyboard (3)]
↳ Fujitsu FUJ02B1 id=9 [slave keyboard (3)]
↳ Power Button id=10 [slave keyboard (3)]
↳ FJ Camera id=11 [slave keyboard (3)]
↳ AT Translated Set 2 keyboard id=12 [slave keyboard (3)]
running
dmesg | grep -i synaptics
doesn't show anything. However running
dmesg | grep -i psmouse
returns a lot of
psmouse serio1: bad data from KBC - timeout
Last edited by flako (2012-11-08 09:44:59)

I have tried doing that with both linux mint, and now fedora live usb. Neither one loads the touchpad correctly. So yeah, our problems weren't really related
Anyway, I tried looking into the
psmouse serio1: bad data from KBC - timeout
messages, and tried running psmouse proto (defined in /etc/modprobe.conf/psmouse.conf) as both raw and imps as per https://answers.launchpad.net/ubuntu/+s … ion/206950 Unfortunately, that didn't solve anything. Using the raw setting meant that the touchpad wasn't loaded at all (as in not appearing in the Xorg.log at all).
The laptop is quite new, but at the same time what i figured from the touchpad vendor & product ID, the touchpad itself isn't. So it should technically work. Before installing arch i booted into windows to see if everything worked, and found no issues with the touchpad. So I have ruled out any hardware errors. Maybe its just the Fn-key that doesn't work yet in Linux? But that doesn't explain the "psmouse serio1: bad data from KBC - timeout" Any pointers to where I should look/ what commands I should run to delve deeper into this issue?
Last edited by flako (2012-09-09 12:10:51)

S430 - touchpad not working at all out of the box

Hi all
I know there's a few people who have problems with the touchpad on their thinkpads, I've got another, different problem!
I got mine out of the box yesterday and neither the touchpad nor the red joystick controller in the keyboard work. The buttons on the touchpad also don't work.
Luckily I had a USB mouse at home and I've been able to the laptop up and running, but no luck trying to get the touchpad working. I've gone through the user guide, the help guide, the lenovo website etc, but not finding anything.
When I go into the "control panel", then "hardware and sound" and select "device manager", the only "mice and other pointing devices" that I have is my HID-compliant mouse which seems to be the USB mouse. The touchpad doesn't feature at all.
If I go into "control panel" and select "mouse" I don't actually have a tab for "UltraNav". Since all the help out there tells me to go to that tab, I don't really know what to do!
If I go through the Lenovo Solution Center, it tells me that the "ThinkPad UltraNav Pointing Device" is disabled and to fix it I need to go to the Device Manager.
But, as already said, in the device manager there's nothing I can do!
Any help would be much appreciated.
cheers
Harry

Hi
This notebook seems to belong to the PSAF5E series.
I wonder where you have found the drivers for this series ?:|
However, I have checked the Toshiba European page and didnt find the Vista touchpad driver especially for this series.
BUT the page provides some touchpad drivers (two drivers) for the Equium A200 PSAEE.
I would recommend installing the Alps Electric Touch Pad driver v7.0.301.4 and the Synaptics Touch Pad driver v. 9.1.14.0.
By the way; its always recommended to reinstall the OS with the Toshiba recovery CD. If you dont have such CD you could order it from the ASP which is responsible for you country.

Wireless Keyboard F Keys not working at all

Just got a new wireless keyboard. Love it other than none of the F keys work and I can't seem to figure out if it's something I need to change in Keyboard preferences or what? Volume, brightness, expose, playback, etc keys all are non-functional. Even if I press the Fn as well.. Also, while there is a dedicated "eject" key on the right, it's actually the F12 (also labeled volume) key that activates the eject icon on the screen. However, that doesn't eject the cd tray at all....
Total confusion, thanks in advance for any advice.

Did you install the keyboard software?
<http://www.apple.com/support/downloads/keyboardsoftwareupdate12.html>

HP Touchpad not working at all

I have a HP Touchpad which isn't responding at all. The screen is blank yet the button is lit up, I know it is charged from my last use. I have tried resetting it with the solutions given such as pressing and holding the home button with the power button, the power button with the volume buttons. I have held them for at least a minute and nothing happened. I have tried connecting it to a laptop, and the computer does not recognise it because its not responding.
Please help.
Thanks

Hi and welcome to the HP Support Community.
If you have not yet been through it, I suggest you review this thread which is "stickied" near the top of this board. It includes most of the suggestions out there to try to get a non-responsive TouchPad back into operation.
One of my TouchPads went wonky on me the other day, after it sat for several days on a TouchStone charging cradle. I plugged it in to a wall charger, let it sit again overnight, and the next day had to restart it several times (home and power buttons) before it finally booted up and behaved normally again.
Make sure you use the original charger it came with, a phone charger does not provide enough power. The micro-usb charging port could also be loose, or the charging cable could be bad.
Keep trying...good luck.
smkranz
I am a volunteer, and not an HP employee.
Palm OS ∙ webOS ∙ Android

Installed MAC OS 10.9 and lost my NUMBERS PAD. Does not work at all.

I installed MAC OS 10.9 and I lost use of the Numbers Pad inbuilt on my Apple keyboard. Does not work at all.

The option for Mouse Keys may have become turned on. To check for that, go to System Preferences > Universal Access, switch the view to Mouse, then turn Mouse Keys off if it is on.
Note that in that same pane there is shown a keyboard toggle for that feature - press the Option key five times in a row to turn it off or on. If Mouse Keys is the problem, that may have been how it got turned on. You can prevent that from recurring by unchecking that item.

HP notebook keyboard and mouse not working

Hi
I spilled tea on my notebook. Now the system boots but keyboard & mouse do not work. Therefore I am not able to
login at the windows screen. When I hardboot, on pressing esc it goes to boot menu, but then the keyboard stops working
so I cannot go to safe mode or recovery mode. I also tried pressing F11 to enter BIOS, but it does not work.
I can however access it via LAN and since I had shared the C drive, I was able to recover the data. Do you have any idea
how I can restore the system now ? I do not have the recovery disks.
Are there any particular function keys to press while booting ?
Thanks a lot for your help

Thoughts on a Soggy System:
Have you tried the obvious -- connecting an external keyboard and mouse? If you are not near a store where you can buy these, you can order them online as a set. Almost anything would do and Windows 7 and 8 install basic drivers for most keyboards and mice without problems when the system comes online.
If you have not waited for several days for things to REALLY dry out before attempting to get back onto the system, then you may get away with this yet - if you WAIT for a few days. Chances are not great, but ... ?
If you can get the system to a repair shop, it is not terribly expensive to have the keyboard / touchpad replaced -- assuming that is all that is wrong with the system -- and the repair is not a lengthy process. This might be something you can do yourself if you are skilled, disparate, in a tiny spot on the planet somewhere (without a repair shop), or like these things...
We can check for part numbers and all of that if you are interested. You can search for for yourself, too.
Start at
Support and Drivers
Enter your information -- Look along the colum and Click on Manuals. You are looking for the Maintenance Manual.
If you do not find it, provide your Exact Product number and I will look for you.
Locate the Notebook Product Number
I am pretty sure you are going to have to have some sort of keyboard control over that system to do more than just use the hard drive to do a hard recovery of the data. You are not at that point until you determine that you cannot access the data through the computer itseslf...
You can always send the system to HP and have it repaired. It is not free unless you have the warranty for it - but it is not horrible to do; HP makes the process pretty easy. It might be worth checking if you do not have a local option available!
Contact HP - USA
Good Luck!
Kind Regards,
Dragon-Fur

MSI GS70 20D Touchpad not working after login when I upgraded to 8.1

Short situation: I upgraded my laptop to windows 8.1, and the touchpad stopped working on the start/desktop screens. I could move it before I logged in, and after it would work for a few seconds, but then it would just stop. An external mouse works just fine, but I still don't want my touchpad not working.
I looked on the MSI USA technical support page, and it said to delete the old drivers for the touchpad and download new ones. I deleted the drives, but every time I try to download the new ones, I get a window that says my touchpad isn't plugged in, and that the drive isn't compatible with my touchpad, which doesn't make sense to me because I looked up my product specifically and tried all three touchpad drivers. None of them worked.
Now I can't use the touchpad at all because I deleted the drivers, so it would seem that the computer doesn't know it has a touchpad because it won't register the touchpad in my devices tab.
Does anyone know what I can do to solve this? Or to at least get the touchpad to register again? I just got this computer for Christmas, I've treated it very well so it hasn't banged up against anything or been dropped or mistreated, so I cannot understand why this is happening. It worked before the 8.1 update, so I'm pretty sure the issue has something to do with that.

UPDATE: So I managed to fix the touch pad by deleting the driver and rebooting, which is weird because I removed the driver completely and never reinstalled it, so the computer shouldn't really know it has a touch pad. But every time I reboot the computer after fixing it, the touch pad goes back to it's old problem and I need to redelete and reboot all over again.
Also, My computer has begun to randomly freeze and not respond to anything, with one such event leading to a blue screen with a WHEA_UNCORRECTABLE_ERROR message. The computer has frozen a total of 6 times, at different moments; when I'm typing on microsoft word, at the login screen, even right when it starts up and the msi loading screen is up. 5 of these times have required a forced shut down, the first time the computer shut off on it's own because it ran out of battery power.
Finally, my computer has begun to periodically for long stretches of time stopped detecting wireless networks and is asking to be plugged into an ethernet cable to connect to the internet. This has never happened to me before, and I know I haven't turned off my network sharing center.
I'm not sure why this is all suddenly happening. It's not like I'm banging my laptop against walls. I'm very careful when I move and use my GS70, so these problems are greatly concerning to me because I just got this computer at Christmas.

Windows 8.1 Onboard Keyboard and Touchpad Stopped Working.

After upgrading to Win 8.1 my keyboard and touchpad stopped working suddenly. They both worked fine for the entire Windows 8.0 release. When I upgraded to 8.1, they both worked for about 3 months. Then what started happening is the computer
would freeze during the startup process.
Now they both don't don't work. But a USB powered mouse works. So with a USB powered mouse and the on screen keyboard I have been troubleshooting. I have removed the drivers from the device manager, reinstalled the drivers, searched for
driver updates etc. Nothing works.
Can someone please point me in the right direction. PC is kind of useless at the moment.

Hi,
Kindly check this application that can show incompatible/unwanted/untrusted/ applications then remove these with different kinds of PC cleaner/Application removal tools.
http://www.getsysteminfo.com/
After Downloaded, Run the Application and Save Report, Upload the Report and Press Submit Button and Click Read the report as an Expert.
If you found anything in these 2 Auto analyses
then find the solution.
1) Driver To Update:
2) Application to Update:
Good Luck!

Rocketfish Bluetooth Keyboard RF-BTKB2 not working under Windows 7 64 bit

Rocketfish Bluetooth Keyboard RF-BTKB2 not working under Windows 7 64 bit
Anyone had successs in this or another Bluetooth Keyboard after a bit of a struggle? What did you do to get it working? When I Add Device in Bluetooth it sees the keyboard but enlessly scans for it when I try to select and connect. The Rocketfish Bluetooth mouse worked just fine.

My friend, i have both, the bluetooth mouse and keyboard here that your talking about. and the keyboard was a struggle to pair with the windows 7 64 bit.... i think i spent 2 days working with it. and i didnt try anything special, i just kept trying to pair
it, and unplugging the dongle and working with it... and after a while. it worked... Lately though, i have been looking into getting a wired mouse and keyboard becuase of the delays and sleep time i have with my current keyboard(rocketfish). supposidly there
is a way around the delays but it disables all the options on your keyboard. IE the media buttons, and web browsing features. and my mouse keeps dieing off too....
Also, after researching these products more, i found that alot of people experienced similar problems with them, Being delays and mouse failure. Even with fresh batteries and all. The products werent meant to be used long term(2-3 years) for extensive use...
I dont know about you but i thinki paid 100 bucks for the pair so thats only 25 bucks a year... Which is kinda silly considering i coulda got a better one that wont cough up on me.
If anyone reading this finds a good wireless keyboard that doesnt delay, and a mouth that doesnt delay...(my biggest concern). Please mention it. i am very interested in.

The Keyboard clicks are not working despite the Keyboard click in settings are ON. Am using IOS 6.1.3.Pls Help me to rech this problem.

The Keyboard clicks are not working despite the Keyboard click in settings are ON. Am using IOS 6.1.3.Pls Help me to rech this problem

Basic troubleshooting from the User's Guide is reset, restart, restore (first from backup then as new). Try each of these in order until the issue is resolved.

Powerbook G4 17" Keyboard or touchpad not working at all.

Similar Messages

Maybe you are looking for