Powerbook will not startup with airport extreme card installed

I have a 2 year old powerbook using 10.3.9 an djust of late when my airport card is in, The computer just sends me to the open Firmware right after i turn it on.when i type mac-boot it comes up with a broken folder icon. however when i take my card out i dont have a problem. is there a wa i can ues my computer and the airport at the same time? what do you think i should do.

it is a 867 mhz g4 with 256 mb ddr ram. 40 gb hd and
a combo drive. i hope that is helpfull.
This PowerBook requires the original Airport card, you can not use the Airport Extreme card in that PowerBook, any attempt to do so could result in damage to both the card and the PowerBook.
Either change the AE card for an original Airport or use a third party 802.11g card in the cardbus slot.
iFelix

Similar Messages

1.5 TB Seagate drive will not work with Airport Extreme.

I have a 1.5 TB external drive connected to airport extreme. I cannot get this drive to be recognizedby the computers connected to the Airport Extreme. The drive show up as "-1.4 TB - Seagate FreeAgent 0138" under disks in Airport Utility can plug it in directly to my Mac Air and a PC and the drive will work. When I plug the drive in directly to a PC or Mac Air, it is recognized and can be used.
I can plug in a 250 GB external drive into the Airport extreme and they will work.
Also, the 1.5 TB works when plugged locally to a PC or Mac using USB.
Anyone know how to get it to work with the Airport Extreme?

Assuming that the drive has been formatted in Mac OS Extended (Journaled) or MS-DOS FAT32, you almost always need to use a powered hub with a drive attached to the USB port on the AirPort Extreme...even if the drive has its own power supply.....because the USB port is under powered and will not supply enough current to most hard drives.

Pc will not work with Airport Extreme LAN connection

I have setup my Aiport Extreme Base Station and my Mac and phone work just fine with the setup. However, I connected a PC directly to one of the LAN ports on the back, and the PC doesn't see the network. Above the port the light is blinking green. Any thoughts?

Is the AirPort Extreme Base Station (AEBS) the only router in your current network configuration? That is, it is connected directly by Ethernet to your Broadband Internet modem? ... or to another router between the AEBS and the modem?
When connected by Ethernet to the AEBS, can the PC "see" the Mac or vice-versa?

No boot with airport extreme card installed

a little history have had the no chime, no lower slot, memory problem fixed once under applecare. they replaced the logic board. much later the same problem has returned, but now i'm way out of warranty. so i removed the 500 mb sticks from both slots and installed a 1 gig in the upper slot. chime returned and computer normally until now. suddenly it will only boot if at all once in ten times to firmware and gives me the choice to type shut down or mac-boot. typing the latter also shuts down the computer. I learned that removing the airport card returns the computer to normal operation but with wifi of coarse. i can plug directly into the cable modem and internet then also works. i have tried all an known good airport with the same results. removing the airport card seems to be the only way to get it to boot. any suggestions would be greatly appreciated. thanks

Since there seems to be a hardware problem where your Powerbook won't work with even a good Airport card, you could take it out and install a separate wireless card in the card slot accessible from the outside of the Powerbook. If you google "cardbus mac wireless card" you'll find some choices.

Imac will not connect to Airport Extreme when configured WPA/WPA2

Imac will not connect to Airport Extreme when configured WPA/WPA2
Posted: Jul 5, 2007 8:22 PM Reply
I just got my Imac to connect to the internet using my Airport Extreme but only by using WEP. I had my Windows XP SP2 machines connecting using WPA/WPA2 with no problem. The Imac will not connect using anything other than WEP, and 1 of the XP machines will not connect using WEP.(I have not tried the other XP machines) I had to set the Airport Extreme for an open network in order to let both computers access the shared hard drive and access the internet.
I don't know what the problem might be and would appreciate any suggestions.
MacBookPro, Imac Mac OS X (10.3.9) Fujitsu tablet PC, 2 XP desktops

hehe...on the visuals. I figured it out already, and I have the old airport card. However, I did a chat with Apple support and while we were chatting I found a USB adapter with MAC drivers which will work. It is:
Hawking Technology HWUG1A Wireless-G USB Adapter with Removable Antenna for Macintosh
Manufacturer Part# HWUG1A
That is the only adapter that actually does WPA/WPA2 that I can find that is for a Mac and not just an older USB that only does WEP. It surprises me that Apple does not have a USB product like this. Anyway, for $56 including shipping, I will have it by Monday or Tuesday. Pretty cool.
Thank you so much for your assistance. It is appreciated.
Lynn

Time Machine will NOT work with Airport Disks!

It looks like Time Machine will not work with Airport Disks after all. All references to Airport have been removed from the Time Machine page:
http://www.apple.com/macosx/features/timemachine.html
It also specifically says: "You can designate just about any HFS+ formatted FireWire or USB drive connected to a Mac as a Time Machine backup drive. Time Machine can also back up to another Mac running Leopard with Personal File Sharing, Leopard Server, or Xsan storage devices."
Surely, they would have included the Airport Extreme Base Station in this list if it was supported.
I really hope there will be another firmware update for the AEBS which will bring compatibility with Time Machine, because Time Machine was the only reason for me to buy an AEBS. (I only use it as a small backup server, I don't even have wireless networking enabled. There were other solutions, e.g. from Synology, which are faster and more reliable than AEBS disk sharing, but Synology stated their network drives would not be compatible with Time Machine.)

Here's how you can potentially use your AirDisk with TimeMachine (beware that YMMV), but it should work as it works with every other "unsupported" device.
1) Mount your AirDisk so it appears on your Mac
2) Open Terminal.app
3) change directories to the AirDisk's root folder located in "/Volumes"
ie: cd "/Volumes/AirDisk Name"
4) execute this command to "bless" the drive to be used with time machine:
touch .com.apple.timemachine.supported
5) Start TimeMachine and if all went well, it should recognize your AirDisk drive and use it for TM.
This should also work on NFS shares, SMB shares, AFP shares, basically anything. It has worked up until the last developer seed, so unless they yanked this at the last minute, it should still work.
Now, the reason why Apple removed this feature may be due to the unreliability of the AirDisk, so be cautious.

I have a Macbook Pro running OSXLion. Do I have to have an Airport or Airport Extreme Card installed? Nothing of this was mentioned to me when I bought the Airport Express at the Apple Store.

I have a Macbook Pro running OSX Lion (10.7.3). Is it true that I must have an Airport or Airport Extreme Card installed in my Mac to set up my Airport Express? Nothing was said of this when I purchased this item at the Apple Store.

no u dont have to install any card...your mac will detect the airport express once its working and u can configure ur Airport xpress using ur macbook pro..

Power Mac G5 fails to start up with Airport Extreme card in.

Hello.
I just received a 'new' Airport Extreme card for my Power Mac G5 1.8 (900fsb). I just installed it and it failed to start up with it in. The mac started up but without my Apple LCD and any USB devices. I did a PMU reset on the logic board and took out the Crucial 3rd party 512mb RAM and tried again but it won't start up. When I take the card out it's business as usual.
Is it the card or the mac that's at fault? Has anyone had this problem too?
Your help will be greatly appreciated.

This problem can happen if:
- the card has not been fully seated into its socket (doing that can take a firm push) or if you installed the card upside down
- the card is defective
- the card socket in the PowerMac G5 has broken or bent contact pins
Check the installation you did with:
http://www.info.apple.com/usen/cip/pdf/g5/apec_c.pdf
If you are sure the card has been properly installed, you are gong to have to either (a) try a different Airport Extreme card or (b) let an Apple dealer or service center take a look at your PowerMac G5.

Is Duel Ethernet Airport Base compatible with Airport Extreme Card?

I am about to upgrade to the new Macbook Pro 15" from my Titanium G4. I currenty have the original Airport card and the dual ethernet Airport Station.
Question - will the new Pro with the Airport Extreme card be compatible with the old base station?
If it will, what would be the advantages of upgrading to a new Extreme Basestation?
maginme
Macbook Pro 15" 2.16 Mac OS X (10.4.7) Powerbook G-4 Titanium

magicnme, Welcome to the discussion area!
Question - will the new Pro with the Airport Extreme card be compatible with the old base station?
Yes, the MacBook Pro can connect to a 802.11b base station like the Dual Ethernet (aka snow) AirPort base station (ABS).
If it will, what would be the advantages of upgrading to a new Extreme Basestation?
The AirPort Extreme base station (AEBS) offers a USB printer port for wireless printing.
The AEBS offers WPA and WPA2 wireless encryption.
Also if you have other computers on your local network, large file transfers between your computers will be faster.

Very high latency on my MBP 3,1 (mid 2007) with airport extreme card 0x168C

Hi
I wanted to let you know that i filled a bug report concerning a problem involving a MacBookPro3,1 and my airport extreme card (AirPort Extreme (0x168C, 0x87) Firmware Version 1.4.16.2)
If you've got any feedback, please feel free to share it with me.
Here's the bug report:
Hello
I'm experiencing very high latency on my MBP when connected using Wi-Fi in my living room and I believe this is a software bug.
This is the trace of my ping test to my router (5m from me):
macbookpro:~ laurent$ ping 192.168.0.254
PING 192.168.0.254 (192.168.0.254): 56 data bytes
64 bytes from 192.168.0.254: icmp_seq=0 ttl=64 time=1536.229 ms
64 bytes from 192.168.0.254: icmp_seq=1 ttl=64 time=536.642 ms
64 bytes from 192.168.0.254: icmp_seq=1 ttl=64 time=3444.466 ms (DUP!)
64 bytes from 192.168.0.254: icmp_seq=2 ttl=64 time=2547.260 ms
64 bytes from 192.168.0.254: icmp_seq=3 ttl=64 time=2671.552 ms
64 bytes from 192.168.0.254: icmp_seq=4 ttl=64 time=1671.272 ms
64 bytes from 192.168.0.254: icmp_seq=5 ttl=64 time=2619.991 ms
64 bytes from 192.168.0.254: icmp_seq=6 ttl=64 time=1619.350 ms
64 bytes from 192.168.0.254: icmp_seq=7 ttl=64 time=2362.474 ms
64 bytes from 192.168.0.254: icmp_seq=8 ttl=64 time=1362.662 ms
64 bytes from 192.168.0.254: icmp_seq=9 ttl=64 time=363.461 ms
64 bytes from 192.168.0.254: icmp_seq=10 ttl=64 time=1407.557 ms
64 bytes from 192.168.0.254: icmp_seq=11 ttl=64 time=1020.437 ms
64 bytes from 192.168.0.254: icmp_seq=12 ttl=64 time=119.570 ms
^C
--- 192.168.0.254 ping statistics ---
14 packets transmitted, 13 packets received, +1 duplicates, 7% packet loss
round-trip min/avg/max/stddev = 119.570/1663.066/3444.466/937.468 ms
These are the details of my network when alt clicking on the network icon:
ca:69:50:37:c7:b2
Channel: 5
RSSI: -54
Transmit Rate: 54
I'm using Channel 5 where my router is the only device available (checked with iStumbler and KissMac).
I compared these results with another computer sitting at the same place:
This is the trace of my ping test to my router using a PC laptop:
C:\Documents and Settings\Laurent>ping -t 192.168.0.254
Envoi d'une requête 'ping' sur 192.168.0.254 avec 32 octets de données :
Réponse de 192.168.0.254 : octets=32 temps=2 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=2 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=3 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=4 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=3 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=4 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=2 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=3 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=3 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=6 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=4 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=8 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=4 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=4 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=4 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=1 ms TTL=64
Statistiques Ping pour 192.168.0.254:
Paquets : envoyés = 16, reçus = 16, perdus = 0 (perte 0%),
Durée approximative des boucles en millisecondes :
Minimum = 1ms, Maximum = 8ms, Moyenne = 3ms
(PC: Win XP SP3 with Linksys Wi-Fi card)
Obviously, my Mac has very high latency where my PC works as expected.
I tried resetting the PRAM, but i didn't affect my results.
I tried updating Airport with the latest AirPort Client Update (http://support.apple.com/downloads/AirPortClient_Update_for_MacBook_and_MacBookPro), but my hardware wasn't eligible for that update (Mid 2007 MacBookPro).
I believe this isn't a hardware bug because i get acceptable ping results when next to my router or in other rooms of my flat.
Can you help me with that bug ?
Regards,
Laurent
Hardware Overview:
Model Name: MacBook Pro
Model Identifier: MacBookPro3,1
Processor Name: Intel Core 2 Duo
Processor Speed: 2.2 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache: 4 MB
Memory: 2 GB
Bus Speed: 800 MHz
Boot ROM Version: MBP31.0070.B07
SMC Version (system): 1.16f11
Serial Number (system): W874551DX91
Hardware UUID: 00000000-0000-1000-8000-001B63B19195
Sudden Motion Sensor:
State: Enabled
AirPort:
Type: AirPort
Hardware: AirPort
BSD Device Name: en1
IPv4 Addresses: 192.168.0.2
IPv4:
Addresses: 192.168.0.2
Configuration Method: DHCP
Interface Name: en1
NetworkSignature: IPv4.Router=192.168.0.254;IPv4.RouterHardwareAddress=00:07:cb:3e:04:ef
Router: 192.168.0.254
Subnet Masks: 255.255.255.0
DNS:
Server Addresses: 212.27.40.241, 212.27.40.240
DHCP Server Responses:
Domain Name Servers: 212.27.40.241,212.27.40.240
Lease Duration (seconds): 0
DHCP Message Type: 0x05
Routers: 192.168.0.254
Server Identifier: 192.168.0.254
Subnet Mask: 255.255.255.0
Proxies:
Exceptions List: *.local, 169.254/16
FTP Passive Mode: Yes
Ethernet:
MAC Address: 00:1e:52:72:05:2c
Media Options:
Media Subtype: Auto Select
AirPort Card Information:
Wireless Card Type: AirPort Extreme (0x168C, 0x87)
Wireless Card Locale: Worldwide
Wireless Card Firmware Version: 1.4.16.2
Current Wireless Network: kalamar
Wireless Channel: 5

Ok, I must have jinxed myself.
High latency with my Negear WPN824v3. As previously mentioned, the other wireless computers connect fine. Latency remains regardless of the power connected or not.
Please advise.
PING 192.168.0.1 (192.168.0.1): 56 data bytes
64 bytes from 192.168.0.1: icmp_seq=0 ttl=64 time=11.607 ms
64 bytes from 192.168.0.1: icmp_seq=2 ttl=64 time=7280.106 ms
64 bytes from 192.168.0.1: icmp_seq=3 ttl=64 time=9209.019 ms
64 bytes from 192.168.0.1: icmp_seq=4 ttl=64 time=8237.475 ms
64 bytes from 192.168.0.1: icmp_seq=5 ttl=64 time=7262.603 ms
64 bytes from 192.168.0.1: icmp_seq=8 ttl=64 time=4313.763 ms
64 bytes from 192.168.0.1: icmp_seq=9 ttl=64 time=3336.361 ms
64 bytes from 192.168.0.1: icmp_seq=10 ttl=64 time=2339.579 ms
64 bytes from 192.168.0.1: icmp_seq=11 ttl=64 time=1344.110 ms
64 bytes from 192.168.0.1: icmp_seq=12 ttl=64 time=345.132 ms
64 bytes from 192.168.0.1: icmp_seq=13 ttl=64 time=1191.119 ms
64 bytes from 192.168.0.1: icmp_seq=14 ttl=64 time=3969.730 ms
64 bytes from 192.168.0.1: icmp_seq=15 ttl=64 time=3992.111 ms
64 bytes from 192.168.0.1: icmp_seq=16 ttl=64 time=3692.648 ms
64 bytes from 192.168.0.1: icmp_seq=17 ttl=64 time=2927.634 ms
64 bytes from 192.168.0.1: icmp_seq=18 ttl=64 time=2130.216 ms
64 bytes from 192.168.0.1: icmp_seq=19 ttl=64 time=1437.424 ms
64 bytes from 192.168.0.1: icmp_seq=20 ttl=64 time=2385.203 ms
64 bytes from 192.168.0.1: icmp_seq=21 ttl=64 time=1393.622 ms
64 bytes from 192.168.0.1: icmp_seq=22 ttl=64 time=396.783 ms
64 bytes from 192.168.0.1: icmp_seq=23 ttl=64 time=1.295 ms
64 bytes from 192.168.0.1: icmp_seq=24 ttl=64 time=115.793 ms
64 bytes from 192.168.0.1: icmp_seq=25 ttl=64 time=3.137 ms
64 bytes from 192.168.0.1: icmp_seq=26 ttl=64 time=10.240 ms
64 bytes from 192.168.0.1: icmp_seq=27 ttl=64 time=2.709 ms
64 bytes from 192.168.0.1: icmp_seq=28 ttl=64 time=9.958 ms
64 bytes from 192.168.0.1: icmp_seq=29 ttl=64 time=1818.371 ms
64 bytes from 192.168.0.1: icmp_seq=30 ttl=64 time=1470.613 ms
64 bytes from 192.168.0.1: icmp_seq=31 ttl=64 time=472.520 ms
64 bytes from 192.168.0.1: icmp_seq=32 ttl=64 time=2255.417 ms
64 bytes from 192.168.0.1: icmp_seq=33 ttl=64 time=18198.039 ms
64 bytes from 192.168.0.1: icmp_seq=34 ttl=64 time=23288.761 ms
64 bytes from 192.168.0.1: icmp_seq=35 ttl=64 time=25150.840 ms
64 bytes from 192.168.0.1: icmp_seq=36 ttl=64 time=26813.832 ms
^C
--- 192.168.0.1 ping statistics ---
63 packets transmitted, 34 packets received, 46% packet loss
round-trip min/avg/max/stddev = 1.295/4906.111/26813.832/7241.136 ms

Slow Speedtest results with Airport Extreme Card

Hi,
We just upgraded our internet to a 5G network with TWC. All the devices in our home are now speedtesting at 100 mb/s wonderfully.
Except one.
My Mac Pro 8 Core 2009 4,1. Running OSX 10.8.5
The mac pro is speedtesting at only 30 mb/s while everything else (MBP, MBA, iphone 5) all speddtesting at 100 mb/s. Alla re connected to the new network.
Is the problem the older airport extreme card? Or is there something I can do in settings or firmware upgrade to sort this?
Here are the specs of the Airport extreme card on the MP:
Card Type:    AirPort Extreme (0x14E4, 0x8E)
Firmware Version:    Broadcom BCM43xx 1.0 (5.106.98.100.17)
Locale:    FCC
Country Code:    US
Supported PHY Modes:    802.11 a/b/g/n
Supported Channels:    1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165
Wake On Wireless:    Supported
AirDrop:    Supported
Status:    Connected
Thanks!

tek_uk, Welcome to the discussion area!
(a) Did you connect the external 'T' AirPort shaped antenna to the back our your G5? This antenna shipped with your Power Mac G5.
(b) Compare the antenna wire connection at the AirPort Extreme card with the photos in KB 108039, Properly attaching the antenna on an AirPort Extreme Card.

Trickling down connection with airport extreme "card"

I recently bought an airport extreme card for my mac pro (older model, 2008?)
Anyways, the problem is that i live in an apartment that offers free wireless. Naturally i suspect the signal to be weak as it has been for a laptop ive used here before. Airport works fine except that when i connect and have a download it starts out high like around 200kb/sec and then slams down to about 12kb/sec then slowly trickles down to a request time out. (I am unable to update because of it.) At first i thought the problem was just well...the apartment, then booted up into Vista and started a download and it keeps a steady pace of about 9kb/sec without timing out.... I tried connecting the 1 and 3 wires, as well as the 2 and 3 and pretty much i noticed no difference. Any suggestions? What firmware is better to use for this?

thnx for the suggestion. That's not my problem.
I do have WiFI connection. So I am already connected tot the AE....the part I do not understand is why I can not connect to the external harddisk that is connected to the AE.
Especially because:
1) It used to be connected
2) My other macbook does connect to the external harddisk

Short short range with airport extreme card

Hello,
my neighbour bought an Airport Extreme Card for his iBook, in order to connect (wireless) to my airport express base station. (our flats are adjacent). His mac is an iBook G4 with OS X 10.3.4
We installed the card, the airport software, but no network appeared in the network menu...
We had to move to my flat and take his iBook very close from the Airport Express Base Station... and then, we were able to connect. But the quality of connection was very poor.
The network works fine, my computer and the one of my Wife (a Mac and a PC) connect perfectly.
Do you have an idea of what could be wrong ?
Compatibility between the iBook and the card ?
Card with a defect ?
Software problems ?
Thank you a lot for helping.

Charles, Welcome to the discussion area!
Did you properly connect the antenna wire to the AirPort Extreme card? Look at the photos in KB 108039, Properly attaching the antenna on an AirPort Extreme Card. It can take more force than most people think to get the antenna wire properly connected.

Cant connect to Netgear WPN824 with Airport Extreme Card

Hi,
I have a Netgear wireless router. I can connect to the router without a problem when I hard wire it. When I go wireless the Mac doesnt even recogonize the router. I have no security right now, so I could try to connect the easiest. This is a brand new Airport extreme card that I installed tonight in my Imac g5. Using OS 10.4.10. Please help!!! Thanks!!!
I would think it would at least be able to recognize the network (which the name is being broadcasted). But it doesnt even show up.

Did you connect the antenna wire to the AirPort Extreme card?
Compare the antenna wire installation with the photos in KB 108039, Properly attaching the antenna on an AirPort Extreme Card.

Connect to router with airport extreme card

Hello, I just oredered a iBook G4 off of Amazon (1.33 GHZ, 1 GB RAM, Combo, 12") with an Airport Extreme card. Can this connect to my Linksys WPA wireless router? I'm new with Macs, so sorry if noobish.

AirPort Extreme Card M8881LL/A
802.11 b/g
Frequency Range 2.4 GHz
Data Rate Up to 54Mbps
Channel Support 802.11b/g:
US/Canada/Latin America/Taiwan: 1-11
Japan: 1-14
Other countries: 1-13
Security 40/128-Bit WEP, WPA, NAT Firewall, MAC address filtering
Antenna Internal
Operation Distance 150 feet
Transmission Power 15dBm

Powerbook will not startup with airport extreme card installed

Similar Messages

Maybe you are looking for