Powerline Ethernet with Time Capsule

Is it possible to connect a cable Modedm and a time capsule wired with powerline? if it is would there be any problems with speed?

Is it possible to connect a cable Modedm and a time capsule wired with powerline?
Possible, but not a guarantee that the connection will occur.
Remember that powerline products are designed to work over the same electrical circuit in a home. When you try to send the signal all the way back to the main power panel and then send it back out to a different circuit, the results can range anywhere from surprisingly good to no results at all.
For that reason, if you are considering powerline products, it would be a good idea to understand the store's return policy in advance before you buy......since you will not know how well.....or if.....the powerline products will work until you try them out in your home.
Sometimes, products from one manufacturer will work well in some homes, but not in others, and vice versa.
To get an idea of how much loss you will experience, conduct an Internet connection speed test with your computer connected directly to the modem and note the results.
www.speedtest.net is a popular site to use, or your ISP may have one that you prefer.
Then setup the powerline products and connect your computer at the far end of the connection and test the speed at that point.
Please post on your results so that other users will benefit from your experience.

Similar Messages

Airtune Over Ethernet with Time Capsule or Airport Extreme

Can the previous generation Time Capsule or Airport Extreme bridge an ethernet client to an Airtunes network?
Current Setup: I have an aluminum iMac wired to my Time Capsule; currently, I use the aluminum as a music server by connecting to several Airport Express clients over the the iMac's built-in Airport for Airtunes support.
Problem: I have 3-802.11g clients dragging my wifi network. I would like to dedicate the iMac's internal network to the g-clients so I don't have to use compatibility mode for my n-network. However, I will lose Airtunes speaker support when I use internet sharing over the built-in Airport. Airtunes does not appear to support the Time Capsule ethernet client.
Nodes:
-AE 802.11g (Airtunes only)
-AE 802.11n (Airtunes and USB printer)
-1st gen Time Capsule (Internet gateway, "creating network" 802.11 g/n,
-iMac 8,1 (Music server via internal wifi, wired TC client)
-Macbook 4,1 (wifi client)
-iPhone
-Canon MP620 (USB to iMac, wifi to Macbook)

Further to Bob's comments..
A Gen1 TC will be using marvel wireless chip and your 2008 and 2010 Macbook will use atheros and/or broadcom cards.. Just open your system profiler and look for info on the airport. We find the mixture of wireless chipsets especially older draft N and later N products can give very varied results.
The very fact you are linking at 270 and not 300mbps shows some reduction from theoretical max speed.. and really to get over 100mbps with any wireless you need perfect setup.. matched wireless chips etc.
Do a test uploading and downloading a file to the TC to see if the LAN speed is better than internet speed.
In reality I think you are doing especially well.. we see loads of people complaining about slow internet here who are getting less than 10% of the speed they get direct when routed through the TC. And on most occasions the limit in speed is not really going to affect what you do, as the real links to the internet are not that fast.

How do I add an Airport Extreme with Time Capsule to an existing non-Apple network?

How do I add an Airport Extreme with Time Capsule to an existing non-Apple network? I have an ISP provided wireless Router that has to remain as the base station. I am able to join my 1/2TB Airport Extreme and Airport Express to the network, but I can't access/use Time Machine.

One option would be to connect the Time Capsule (TC) to the ISP-provided wireless router by Ethernet. You can then configure the for a roaming network. Then, depending on what your goal is for the AirPort Express, you can either: 1) Add it to roaming network, 2) Configure the TC & the Express for an "extended" network, or 3) Configure the Express to "join" the roaming network for AirPlay.

Can I use Extreme with Time Capsule to extend my gateway router and still use Capsule as "external HD"?

Bought Airport Extreme with Time Capsule version 7.7.2 with 2 Terabytes Feb 2014. It was probably an expensive mistake, but after searching for weeks for a external hard drive, it seemed reasonably priced to just use the capsule as my external hard drive for the price I paid. Spend an hour with Apple Care to get it working-had to use ethernet cord to my iMac OS 10.8.5 processor 2.5 GHz Intel Core i5. I did not "need" the airport as we have a Winstream SAGEMCOM modem/router (Sagemfast 1704) But, I was desperate and about to lose my old external hard drive with literally had 3 computers worth of information on it. It had already "died" once, but got it back, so once I got the airport/capsule and was told I just paid for an expensive HD, I had no time to take it back to get something else-I had to transfer my info right then. We (Apple Care) could not get it to work as a HD wirelessly. It may be because it was being set up for the first time; I don't know. I was hoping I would get a transcript of all done so I could do it myself if needed later on, but when I looked at my email-they didn't do that. (Don't know if that is normal, I was used to other "techs" sending the email.) So now I really want to try to move my airport and "extend" our wifi as it said on the "box" that you could do...
Our Windstream router had to be placed in the lower level at the bottom of our stairs. The stairway is "open" (no door going down the steps). I want to place the Extreme at the top of the stairs so that we can use some things in our offices or not have Netflix on our TV lose connectivity when we all are on our computers.
I know I need an ethernet cord to connect directly with the modem/router to the Airport Extreme. I don't know what I will need to do after I connect it as it was so goofy when we set it up the first time (With the app it would disappear and not show up..) But my biggest concern is will I be able to still use the capsule as my hard drive and will I be able to do it wirelessly? (Even with it connected by ethernet, every day I have to re-connect to it before I can click on anything on the hard drive. It never shows up on it's own as my old HD did. That drives me nuts.) I do back up using the Time Capsule feature as well. I appreciate any help.

I am still willing to plug in the ethernet cord to the modem/router and try it IF I was able to get a step by step instructions..
Connecting the Time Capsule (TC) to the existing Winstream by Ethernet would be the basis for a roaming type network. This type of network allows you to basically "roam" with a wireless client and connect to either router. This, in essence, would provide you with an "extended" wireless network. The Apple routers can work with just about any manufacturers' routers in this fashion.
The keys to having a successful roaming network are as follows:
The routers must be interconnected by Ethernet.
Both routers will broadcast their own Wi-Fi network, but MUST use the same Network Name (or SSID), wireless security type (WPA or WPA2), and wireless password.
The TC MUST be reconfigured as a bridge.
Connect a single Ethernet cable between one of the Winstream's LAN ports and the WAN (circle of dots) port on the TC.
The basic steps are:
Power-down the Winstream.
Perform a "factory default" reset on the TC. Leave the TC powered-down after the reset has completed.
Connect the TC to the Winstream using an Ethernet cable.
Power-up the Winstream. Wait at least 10-15 minutes to allow it to initialize.
Power-up the TC. Wait at least 5 minutes to allow it to initialize. (Note: Since we just reset the TC it will be performing as a wireless router that will be broadcasting an unsecured Wi-Fi network with a Network Name of something like: Apple Network NNNNNN)
Connect your computer to the Winstream's Wi-Fi network.
Run the AirPort Utility. select the TC, and then, select Edit.
Go to the Network tab.
Change the Router Mode option to: Off (Bridge Mode)
Select the Wireless tab.
Verify that the Network Mode option is set to: Create a wireless network
For Wireless Network Name, enter the Wi-Fi network name used by the Winstream.
For Wireless Security, select the equivalent security type that is used by the Winstream. (Note: Use "WPA/WPA2 Personal" if the Winstream is using WPA/TKIP. Use "WPA2 Personal" is the Winstream is using WPA2/AES.
For Wireless Password, enter the same password used by the Winstream.
Select Update and allow the TC to restart.
As far as your external HD, yes you should still be able to use it as before.

No internet with Time Capsule

I cant get internet through my time capsule. When i run network diagnostics, the network status says that:
Airport, Airport Settings, Network Settings and ISP are fine, but the Internet and Server have failed.
I use a cable modem from virgin media.

gareth1962jones wrote:
I've just installed time capsule with one airport extreme - which is all working fine except that I now can't get into the internet: somehow, I've ended up with two wifi networks - a new one one that the Time Capsule works with but no internet and one that connects me to the internet but not Time Capsule (the wifi network I had beforehand)
I've connected my original wireless modem to the Time Capsule via an ethernet cable. Airport utilities tells me this cable is not connected so I suspect the problem is something to do with that.
Do I need a wireless modem at all with Time Capsule?
Unless you expect problems with range, you might try replacing your AirPort Extreme with the Time Capsule. There are ways to get them to work together, but you'll probably be happier and have less hassle just doing the replacement.
I'd start by using the "Manual Setup" option of AirPort Utility to do a "File -> Save A Copy As..." of your existing AIrPort Extreme configuration. Then connect the Time Capsule in its place and use "File -> Import..." to bring your old settings into the TIme Capsule. There are probably some things you'll need to tweak, but the old settings will at least get you going in the right direction.

Use Network ready printer with Time Capsule?

Recently bought a laser all in one Canon printer that was network ready. Canon tech support told me it would not be compatible with Time Capsule (500 GB) as the wireless source. Is this true?
If true, what printer brands will network easily with the Time Capsule?
Thank you!
In search of new printer

Welcome to the discussions!
If the all-in-one is "network ready", it will have an ethernet port to connect to the network. It will need to connect by ethernet if you want to be able to use the scan, fax, copy, etc functions.
If you are planning to connect the all-in-one to the Time Capsule USB port, the printing function will work if the device is compatible. The other functions will not be supported.

I'm trying to extend my wifi network with time capsule but it can't find the existing wifi network

I'm trying to extend my wifi network with time capsule but it can't find the existing BT wifi network even though it is there with a good signal strength. The Time Capsule is connected to a Netgear router via ethernet.

You will need to start over on the setup of the Time Capsule as follows:
Disconnect any Ethernet cables that might be connected to the Time Capsule, but leave it powered on
Hold in the reset button on the back of the Time Capsule for 8-10 seconds and release. The reset button is located next to the AC power socket.
Allow a full minute for the Time Capsule to restart to a slow, blinking amber light
Connect the Ethernet cable from a LAN <--> port on the Netgear to the WAN "O" port on the Time Capsule. The Ethernet cable must remain connected at all times.
Click the WiFi icon at the top of the Mac's screen
Look for a setting of New AirPort Base Station
Click on Time Capsule
The example below shows an AirPort Express. You will see Time Capsule on your screen.
That will get the setup wizard going. It will take a minute to analyze the settings, then display a screen that looks like this, except you will see a picture of the Time Capsule
Network Name..........Type in the exact name that the Netgear wireless is using
Base Station.............Type in a name that you want to call the Time Capsule. Use something short and simple. Mine is TC, for example
Password..................Type in the exact password that the Netgear wireless requires
Verify.........................Verify the Password again
Click Next
The setup wizard will configure everything for you automatically. When you see the message of Setup Complete, click Done.
That's it. Now you have one big "extended" network. Technically, this is called a "roaming" network.

Wi-Fi connectivity lost, ethernet through time capsule works fine. Wi-Fi adapter broken??

Weird... I have been using my iMac through Time Capsule.... Wi-Fi set-up works fine for iPod, iPad and Windows PC. Last week I lost my connectivity on iMac temporarily... it re-connected automatically several times, but after yesterday the connection didn't come back. Hooked up my Airport Express for speakers so now I'm connected through Airport Express and Ethernet connector on iMac. What can be wrong here??? Any help is appreciated, and hey, no, the iMac is within Wi-Fi distance!
Thans a lot..
Peter

Try downgrading your TimeCapsule to 7.5.2 (it proved to solve almost all the problems with Time Capsule). You can check how to do it here: http://support.apple.com/kb/HT1218

Using Airport Express as separate wifi network vs extender with Time Capsule?

Hello all. I recently converted my home computer network from Windows/PC based to an iMac with Time Capsule. On my previous setup, I had a Cisco/Linksys router with wifi, and I also had two Airport Expresses in separate areas of the house where the Linksys had a weak signal. Obviously, I had the Airport Expresses set up as "separate" wifi networks, as they could not be used as network extenders with the Linksys. This setup seemed to work really good, as the 3 wifi networks provided good blanket coverage in all parts of the house. Each network also seemed to "hand-off" to the other pretty well, meaning that Airport Express 1 would show as the active network when you moved far enough away from the Linksys (or insert any of the network names here, even though I'm pretty sure that the device accessing the network has more to do with this than the networks themselves). In particular, the speeds that I got from the Airport Expresses actually eclipsed the speeds that I would get from the Linksys wifi.
My issue is that after I converted everything, I left the Airport Expresses as "separate networks" and essentially removed the Linksys/Cisco router and replaced it with the Time Capsule. So I still have 3 separate wifi networks, just like before, with the Time Capsule network taking the place of the Linksys wifi network. While the Linksys and the Airport Expresses seemed to co-exist together nicely, I get the feeling that the TC and the AEs are somehow working against each other or at least competing with each other for bandwidth. For example, if I have my iPhone right beside my iMac and TC, and I run a speed test on the iPhone using the TC wifi network, I get download and upload speeds in the range that I am expecting (30-40 mbps download). However, when I walk down the hallway to the other end of the house, the TC tends to remain the dominant wifi network, even when I am in the same room with one of the AEs (this is where they used to "hand off" nicely between networks). When you run a speed test in this location still on the TC wifi, the speed drops down to 5-7 mbps, and worse, I believe the signal becomes inconsistent because webpages and data often seem to be freezing in the middle of downloading. I understand that the distance from the TC is causing this, because my solution has been to manually switch from the TC to the closest AE, and that fixes the issue. Run a speed test after I manually switch to the closest AE when I am in the same room as an AE, and the speeds pop back up to 30-40 mbps.
My question is this: would switching the AEs to "extenders" of the TC wifi network help this issue? Honestly, my laziness was one reason that I did not do this when I setup the TC initially, because I have several devices that access the AE wifi networks that I'd have to update with the new network name and password. Everything was working great before, and I just didn't want to upset the apple cart. But if I have created an unfriendly environment between the TC and the two AEs, I certainly have no problem making the change now. I just wasn't sure if making this change would fix my problem or not. I know it's a mundane thing, but I'd like to be able to roam the house without continuously having to manually switch between wifi networks to get a consistent signal.
Sorry if this is a simple issue. I am admittedly a newbie with the TC and its interaction with the AEs.
Thanks in advance!!

It is not a simple issue.
Exactly which method works best is going to take some experimentation.
The way you are trying to set it up as a roaming network is generally considered the best.. but the devices like iphones do not hand off neatly.
It is interesting that they in fact used to hand off better using the Linksys.. which could be due to its poorer range. The new TC having so much better range is causing the phones to not swap "towers" to the local express.
Test it with a Mac laptop.. as generally they do hand off better.
I cannot quite figure out if you are using roaming correctly. All the wireless should have identical names, with identical security setting and passwords.
The only thing that should be different is wireless channels on each item. And you are likely just using auto anyway.
So each device is creating a wireless network. And for 2.4ghz one should be channel 1, then another channel 6 and another channel 11. For 5ghz it will be same idea but there are more channels available.
When you extend wireless, everything runs the same channel. But the wireless speed is reduced. You must disconnect ethernet to each of the expresses.. and the problem is your 30-40mbps will reduce permanently to 15-20mbps for all clients. So take your choice.. 15-20mbps for all clients forced to double hop is better than 5-7mbps which you experience now when you walk around.. although I am not sure how much browsing you do whilst walking. You may need to compromise which is the better out of several not great alternatives.
I would have a test.. which is wrong btw.. but I have heard that it works.
In your roaming network at the present time. Try setting each router to a manual wireless channel.. and fix all of them the same. So for instance, set 2.4ghz to channel 11. Try fixing the 5ghz as well, say the TC is defaulting to 149, it might not actually respond to manual wireless channels.. you will need to test this.. say set to 36 or 40 and see if the TC is actually changed.. if not just set all the expresses to 149 as well. What you are doing is trying to reinforce the wireless in each area.. but this is actually wrong. So all will have same wireless name and same security wpa2 personal is the only valid one.. and all the same password.
Test with a few clients and see if the results give you decent local speeds as well as better roaming.. once you decide which to do, then you will need to change all the clients.

My MacBook Po can not connet with Time Capsule for Internet. Back-up are ok

Hi to all,
If I connect the ADSL line to Time Capsule no Internett available.
If connect the live with eternet cable to MacBook pro all is fine.
Mack book pro do all the backup with Time Capsule in WiFi
Hot to have the MacBook connectid to Time Capsule in WiFe for internet too??
Easy explanation please, I'm really beginner

Your original question was How to use Time Capsule for wireless back-up but not Internet?
There is no reason for you to connect the tower....or anything else...using Ethernet if your goal remains that same as you stated.
If you are asking if you can backup the Tower using Ethernet, and not wireless, then you can connect the tower to one of the LAN <-> ports on the Time Capsule....not the WAN port.
Yes, it appears to work without plugging into my tower.
Correct, it will work.
I just have to select the network that it created. Of course, I have no access to the Internet while this is happening and it can not auto backup, unless I am on that wireless signal.
As I stated, that is the downside to trying to back up without an Internet connection. You have to establish another network...and backup over that network.
If you are asking if you can stay connected to the work network while also backing up to your non-Internet "private" network, that is not possible.

I connected my Canon printer to time capsule, and can print OK. However, I can't get the printer scanner to work. How do you set up the scanner with Time Capsule?

I connected my Canon printer to time capsule, and can print OK. However, I can't get the printer scanner to work. How do you set up the scanner with Time Capsule?

You cannot use USB. It has to be a network capable printer.. is it?? You did not indicate how it is connected.. but by wireless or ethernet then scanning is possible otherwise not.

Clone with Time Capsule

I am currently using TC to back up my iMac and my Macbook.
Can I also use SuperDuper to make a clone of my iMac? I have a 500GB TC.

Hello Gerard and welcome to the discussions.
A few thoughts:
Continue to use your FireWire drive to backup the Entourage Database and Parallels Data Files.
Use Time Capsule to backup everything else, excluding the Entourage and Parallels files. With TC trying to backup every hour, this just won't work with files this large. I know that it is not possible to do incremental backups with Entourage because of the file structure (monolithic, I believe it is called) and assume from your description that Parallels is the same type of file structure. I exclude the Entourage database from my TC backups and instead backup to a small separate USB drive daily. All seems to be well.
If you do elect to use the Time Capsule in your system, you are smart to use ethernet for the first backup. Subsequent incremental backups will go much faster since only changed files will be backed up (assuming you exclude Entourage and Parallels),so wireless should work well assuming a good connection.
Another thought, if you do not need to backup hourly, take a look at Time Machine Editor, http://timesoftware.free.fr/timemachineeditor/, for options on setting the backups whenever you would like with Time Capsule and Time Machine.

Internet Problem with Time Capsule (Wi-Fi) and AT&T U-verse Motorola NVG589 (Bridge Mode)

I'm having a problem with my Internet connection. For some unknown reason it keeps cutting out every 5 min for about 5 seconds. The wi-fi signal doesn't drop or anything like that, just the internet connection stops working for a little bit and then its fine again (pages don't load, etc).
Here is my current set-up:
1. AT&T Motorola NVG589 - set to bridge mode as per instructions here http://www.dslreports.com/faq/17734 (followed instructions step by step)
2. Apple Time Capsule (latest model 2TB)
3. Motorola is connected to the Time Capsule through an ethernet cable.
I tried contacting AT&T and they just sent me a new Motorola router, I installed it, put it in bridge mode and still the same thing is happening.
I am thinking maybe there is some problem in settings or something. Airport Utility is showing everything in "green", no problems there.
Please let me know if anyone can help.

Ok, here is an update on how I decided to deal with the problem. I will include all of my troubleshooting step by step for easy reference.
1. At first I put the NVG589 into Bridge Mode and used the TC as the main wireless router. This didn't work as my connection kept dropping for no apparent reason.
2. Second, I tried to put the Time Capsule in Bridge Mode and connect it directly to NVG589. This didn't work as my connection would still lag out for 5 seconds about every 5 minutes.
3. Third, I bought an ASUS RT-AC87U Wireless AC2400 Dual-band Gigabit Router to try and substitute the TC in previous steps and see if it helps. Same problem persisted when I put the NVG589 into Bridge Mode and RT-AC87U as the main router as well as RT-AC87U into bridge mode and NVG589 as the main router. The problem was exactly the same as when I tried using TC initially so my conclusion was this is NVG589's fault of being not compatible with other wireless routers.
4. I looked around everywhere and came up with the only feasible solution possible (for me at least):
Currently I use NVG589 as my main wireless router. I works pretty well and even though it doesn't have the specs of TC or the ASUS router my WI-FI connection is pretty fast and stable. In order to have Time Machine wireless backups, I purchased a Western Digital My Cloud Drive that is connected directly to the NVG589. Everything seems to sync and work well together.
I know this is not the ideal solution most people are looking for. But it works for me. Patiently waiting for AT&T to start offering NVG599 (http://www.dslreports.com/forum/r28967809-NEW-U-verse-Gateway-Motorola-NVG599-WI RELESS-AC-AC1600) in my area. Once I get my hands on it will report back on how it will react to all the steps above and hopefully work well with Time Capsule.
Shoot me any questions you might have. Hope this was helpful for some of you.

Is PPTP-ADSL supported with Time Capsule?

As I figured out, internet connection via the WAN port with Time Capsule is only possible in two modes: Ethernet DHCP/static (mostly used with cable modems) and PPPoE (for DSL). However my ADSL modem requires a PPTP connection, which does not seem to be supported. I am stuck with this... any clues? No, and I don't want to use another router device to solve this issue... (which I have to do now).

Hi, I have the same Problem...
In Austria most of the DSL Prividers ONLY !!! support PPTP Protokoll for conecting to the WWW. Every 70 € DSL WLAN Router is able to support this Protokoll. I also hope that Apple will solve this problem with the next Firmware Update.

Intermittent internet problems with Time Capsule

Hi
I have the following set up for internet in the UK. TalkTalk broadband (8 meg) through BT landline - Draytek Vigor 120 ADSL Ethernet Modem - Time Capsule - Wireless n to Macs.
I am experiencing two problems, one that a couple of times a day the Time Capsule starts flashing orange and in Airport Utility the problem generally appears to be with the PPPoE server. Sometimes the issue spontaneously resolves itself within a couple of minutes. Other times I have to restart both the TC and the modem and then I get a green light and everything works again. I was experiencing similar problems with a previous modem and specifically bought the Draytek modem which translates the PPPoA service from TalkTalk to PPPoE which the TC prefers (as i understand it), but still I am experiencing the same issue.
The second issue I am experiencing, which is a common experience, occurring maybe half the time I use the internet is that I need to reload web pages a lot to get them to load. So I might click on eBay say and the page doesn't seem to want to load at all, so I either cancel the loading or try clicking again on the bookmark again (or a link) and if i'm lucky it will then load quickly. If not I will have to try again. This seems to happen more with some websites than others, and emptying the cache seems to help, but the problem soon re-emerges.
I am not sure if these two issues are interrelated, but it all adds up to a fairly frustrating online experience. I am not sure whether the issue is with the ISP, the modem, the TC, or some combination of these. I experience the same problems regardless of which Mac I am using (there are three in the house) and which browser, so I am presuming that the issue is not with the Macs, but why clearing the cache would help I am not sure.
I would be grateful for any help in resolving these issues
Thanks
Nick

Hi Nick,
No idea on the TC, but anyway you can elimunate it in the setup for a test?
So I might click on eBay say and the page doesn't seem to want to load at all, so I either cancel the loading or try clicking again on the bookmark again (or a link) and if i'm lucky it will then load quickly. If not I will have to try again.
Try putting these numbers in Network>TCP/IP>DNS Servers, for the Interface you connect with, Airport...
208.67.222.222
208.67.220.220
Then Apply
OOPs, you're on 10.5.8, it's in a little different place, Network>Advanced>Somewhere...
Message was edited by: BDAqua

Powerline Ethernet with Time Capsule

Similar Messages

Maybe you are looking for