Powermac Dual 2.0Ghz hard drive upgrade

Hi,
I was wondering if I could upgrade my hard drive. I was in Best Buy the other day and they had 2tb internal hard drives for a great price and was wondering if I could upgrade? Any if I can could I do it myself or would it be easier to take it to a computer store like Apple? Is it hard to put a hard drive in. Cheers everyone!
Garett

Hard drives are relatively easy to remove and install. Look in your manual (or download it from the support site) and you will see that it's pretty easy.
Manuals site: http://support.apple.com/manuals/#powermac
2TB drives run fine in these machines, with the popular caveat about avoiding "green" drives for the volume your system boots from. 2TB drives are getting pretty inexpensive now.
Now, you need to transfer data from your old drive to the new drive, and probably the easiest way to do that is put the new drive in the lower bay first. (If you still have the overmold screws in the fan tab to the left of the drife bays, you should use those, but I would suggest putting the screws in the rear holes and the middle holes on the side of the drive, as that makes it a lot easier to get the drive back out. When moving the new drive to the upper bay, though, you need to move those screws from the middle holes to the front holes on the side.) Use Disk Utility to erase the drive, selecting Mac HFS+ (Journaled) as the format, then use SuperDuper! to clone your old drive to the new one. (If your old drive has multiple partitions, then you can partition the new drive to the same number of partitions, if desired and clone each partition.)
http://www.shirt-pocket.com/SuperDuper/SuperDuperDescription.html
Then move the new drive to the upper bay and you should be good to go.
Oh, and be prepared to see that "great" price you paid for your new 2TB drive continue to fall after you pull the trigger. I started at $108 on special and then hit $98 and I think they are largely going for under $90 on special in my area.

Similar Messages

How can I browse T.M. backups made BEFORE internal hard drive upgrade?

Hi, all. I have googled and googled with no info on my particular situation. Maybe one of you can help. Here's hoping...
I have a MacBook Pro and use Time Machine to back up to a Firewire hard drive. I do not back up my System and Applications, just files. Consequently, when I recently upgraded my internal hard drive I restored all my data and settings from the original internal hard drive (not the Time Machine).
From there Time Machine began making NEW backups of the NEW hard drive, no problem, but I cannot browse the backups of the previous internal hard drive. Is there any way I can get Time Machine to recognize all of these backups as existing from the same machine and let me browse back beyond the internal hard drive upgrade?
Any help is greatly appreciated!

I think you have to browse them separately, but you should be able to do so by right-clicking (control+click) on the Time Machine icon in the dock or by holding the option key when clicking the icon in the menu bar.
Choose "Browse other Time Machine Disks" and you should see the old series of backups.
~Lyssa

Hard Drive upgrade

I'm considering a hard drive upgrade but i dont know crap about them. I went over to newegg because i heard it was a good site and found this one......
"Western Digital Scorpio Blue WD5000LPVT 500GB 5400 RPM 8MB Cache 2.5" SATA 3.0Gb/s Internal Notebook Hard Drive -Bare Drive"
The only problem is, I dont know wheter it is compatible with my Early 2009 13 inch macbook pro..... Should I go with this one or are there better ones out there? I'm not really worried about price. I was aiming to get a 500gb. Thanks.

It is compatilbe if it's a 2.5" notebook SATA II 3.0 Gb/s model. Take Csound1's advice. If you buy a WD drive or any other makers' drives do not purchase any "green" drives as they don't work well in Macs.
If you want better performance get a drive rated for 7200 RPM with as large a cache as possible (typically 16 MBs.) Other makers to consider include Hitachi, Seagate, and SamSung.
If you want faster speed consider the Seagate XT500 hybrid. Or visit OWC and look into their DataDoubler that enables you to replace the optical drive with an SSD (or another HDD.)

Hard Drive Upgrade - Incorrect Capacity Shown In Disk Utility After Installation

I have an older model Macbook Version 2.1 that had an 80GB hard drive installed. I have just installed a Western Digital Scorpio Black 500GB internal hard drive upgrade and successfully cloned my data over using Carbon Copy Cloner. The problem I have encountered is that only 98.1GB of capacity is shown in Disk Utility for the new hard drive. After starting the computer using my bootable copy via an external USB drive, I formatted the newly installed 500GB drive with the appropriate Apple formatting (e.g. GUID and Mac OS Extended Journaled) but it only shows 98.1GB of space available on the new drive. I was able to successfully clone the information from my bootable back-up of the old drive to the new drive but I just don't have the full 500GB capacity available to me.
What should I do? Is this a problem with the new hard drive or is there something I need to change on my Macbook to "see" the whole capacity of my new drive?
Thanks for your advice,
Dave

Hi Andrew,
When I formatted the new drive did it with 1 partition and it displays a TOTAL of 98.1GB free space (both in Disk Utility and About This Drive). As far as I can tell, the Macbook is treating the new WD drive as if it is only a 98.1GB drive rather than the 500GB drive that it is.
Thoughts?
Dave

How do I reinstall my operating system after hard drive upgrade on MacBook pro? I have Snow Leopard install disc

How do I reinstall my operating system (Snow Leopard) after a hard drive upgrade. I did a Time Machine backup before the new hard drive was installed. I put in the Snow Leopard install disc and don't get the icon I'm supposed to double click to install Snow Leopard and then the backup.
HELP PLEASE!!

Is the new HHD in the MBP?
Is the new HDD formatted Mac OS Extended (Journaled)?
Where is the old HDD? In an enclosure? What is on the old HDD, your user data? Is the Snow Leopard System on it?
Do you have a separate Time Machine Disk with your user data?
Answers to these questions should give an exact status of your situation so that one can proceed in the right direction.
Ciao.

IPod sync problems after hard-drive upgrade/change

Hello all,
Can anyone PLEASE help?
I have just had my hard drive upgraded/changed from the original 640GB drive to a new 2TB drive. I've also had an additional 4GB of RAM added to now give me 8GB RAM.
Absolutely everything else seems to be working fine (unusual for me and I'm often at the end of bad luck in such circumstances). The only thing I'm having problems with is syncing my iPod Classic with iTunes. Incidentally, I have the latest version of iTunes and my iPod software was up to date the last time I checked.
Before I go further, my system specs are:
iMac
24-inch, Early 2009
Processor 2.66 GHz Intel Core 2 Duo
Memory 8 GB 1067 MHz DDR3
Graphics NVIDIA GeForce 9400 256 MB
Software OS X Mountain Lion 10.8.2 (12C60)
When I connect my iPod Classic, the iPod screen initially shows 'Synchronisation in progress' (or whetver similar wording it actually is)... but this is just very briefly. It then indicates "Connected", and that's the way it stays and doesn't change at all.
It takes time to actually show up in iTunes, and when it does, I now have to very quickly click the iPod button (to bring up the iPod screen on iTunes) before the pointer turns into the spinning beach ball.
Now, it hangs... and hangs... and hangs... and hangs.
During this, I notice that "Manually manage music and videos" is ticked (which I didn't have ticked before), and also 'Enable disc use' is also ticked, although greyed out.
Occasionally, the spinning beach ball will disappear and the pointer will return, but this is very very briefly and I have a split-second to try unticking - first - the "Manually manage music and videos" box and then - later, if I'm lucky - untick the 'Enable disc use' box. However, on the odd occasion I've managed this, I haven't been able to go further except for two occasions when I managed to click "Apply". The iPoid on those to occasions started to update... but went nowhere... it just did nothing.
When the thing finally just hangs and hangs, I eventually have to 'force quit' iTunes and unplug the iPod without first ejecting. There was one other occasion when I managed to - split-second when the spinning beach ball disappeared - to click "eject" and the iPod succesfully did so.
There were a couple of occasions in the past when I had trouble with my iPhone and was told to delete/trash the iPhone photo cache folder. Remembering this, I tried this for the iPod (iPod photo cache) and it made no difference... same situation.
I did notice on one occasion at the beginning of all this that when I managed to unplug my iPod from iTunes, all the album covers were missing from the iPod (although still in iTunes). This was long before I tried deleting the iPod photo cache folder though.
Any help would be greatly appreciated.
Best regards
BionicDan

First things first the spinning beach ball is usually an indication that Search is going nuts.
Turn off Search entire Library by clicking on the downward pointing arrow to the right of the Magnisying glass and untick Search entire library.
Is your music still in iTunes on your new hard drive or is it only on your ipod?
If it is in your itunes then you should be able to plug in the iPod and uncheck Manually Manage music and sync
If the music is only on the ipod connect up as above click on the device and Drag all the music from your device to the library. then you can uncheck manually manage music and sync as normal

Time Machine confused after iMac hard drive upgrade

Here's the deal. I had my 24" iMac internal 250-gig hard drive upgraded to a 1-Terabyte drive. Tech guy cloned them with SuperDuper. New drive booted right up and works great. My question is regarding Time Machine, which I have set up to backup to an external drive. I assumed because old drive was cloned to new drive, Time Machine would think it was the same drive and just keep backing it up as it always has. But what happens is Time Machine just keep saying "processing" and nothing ever happens.
Is there a way to tell TM to start backing up the new drive as it always did or do I need to delete my current (1 1/2 yr. old) TM files and let it start from scratch again? I really don't want to do that. Any ideas?

As V.K. says, that procedure may or may not work.
The reason for the long preparing stage is that TM, seeing a different drive, is examining every file and folder on your system, and may do a full backup of your entire system.
Download the +Time Machine Buddy+ widget. It shows the messages from your logs for one TM backup run at a time, in a small window. You'll probably see a message about a UUID error referencing your internal drive --that means TM doesn't recognize it as the same one it last backed-up.
Then you'll probably see one about a "deep traversal." That means TM is looking at every file and folder on your system to see what needs to be backed-up. This takes quite a while, of course, and you won't see anything being backed-up (xx MB of yy GB) until it's done.
If TM does perform a full backup, it may have to delete a lot of your old backups to make room for the new one. If it can't delete enough, it will fail.

G40 2384-A9U Hard drive upgrade

I updated the bios to 1.21 which seems to be the latest bios 2006. The hard drive upgrade listed for purchase 2004 was an 80G. I was hopeing that I could put a larger dirve in because the newer bios was 2 years past the hard drive upgrade listing. I tried a 250G but it does not seem to be recognized. Does anyone know what the max hard drive size the latest bios supports?
Solved!
Go to Solution.

I first entered CMOS (setup) and under security, and set the desktop to disable. I was able to transfer the data to the 250G from the 40G using Ghost 2003 and selecting the image setting -IB (Image Boot). I was fortunate enough to have a floppy drive on the notebook (G40 2384-A9U). I attached an external USB 40G drive to the notebook, booted with Norton's Ghost 2003 boot disk created with USB support enabled. I went into options and selected Image Boot under the image tab and then copied the existing 40G drive to the external 40G USB drive. I then replaced the 40G drive in the notebook with the 250G drive, booted with the Norton Ghost disk and selected the image boot again and copied the 40G USB drive to the new 250G drive now in the notebook. I went back into the CMOS (setup) and put the security for the desktop back to normal. The only thing different seem to be the utilities are missing if you hit the IBM access button. I notice that when you disable the security for the desktop in CMOS, you will see an unpartitioned space of almost 2Gigs. This appears to be where some of the 4 sectors that lenovo uses to hold the boot information and probably their utility programs. The norton -IB switch does seem to get the boot sector information but not the utility portion of the unused area. The result is the unused space is reduced to only 2 megs on a 40 Gig drive and shows up as 4 megs on the 250 Gig drive.

Spinning beach ball after hard drive upgrade

Im running a macbook pro i7 2.2ghz 8gb ram version 10.6.8 SL
I recently upgraded my 128gb ssd to a 512gb ssd drive. I cloned the drive to new drive and ever since then, I get the spinning beach ball very often whereas I never got it prior to the hard drive upgrade. Is there anything I can check or do to eliminate the freeze ups? It is VERY annoying. Or do I just need to do a fresh install on the new hard drive.
thanks in advance

Did you properly prep the drive first:
Drive Preparation
1. Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
If you are preparing an external or a non-startup drive, then open Disk Utility in your Utilities folder.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID (for Intel Macs) or APM (for PPC Macs) then click on the OK button. Click on the Partition button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.

Hard Drive Upgrade in Vista

I have an IBM T60p with original 90 gig HD. I spent a weekend trying to upgrade to a larger capacity drive. Downloaded several commercial programs. None of them worked properly. I finally found a way to use Vista to complete the task. This procedure works, have a new 320 gig WD 7200 RPM drive working correctly in my computer. Hard drive Upgrade in Windows Vista
This procedure was used on an IBM ThinkPad T60p with 90 gig SATA HD.Machine was upgraded with a Western Digital 320 gig BEKT SATA drive (Scorpio Black).
Before you start:You need to change the BIOS setting for Windows to recognize your new drive.
Reboot and enter BIOS
Select “Config” => Serial ATA (SATA) => SATA Controller Mode Option: => COMPATIBILITY
Save and exit
Review Boot priorities to enable the Boot from CD option
Have a copy of Windows Vista on CD; the version does not matter, you will use this only to boot from CD.
See WD product description at following website
http://www.wdc.com/en/products/products.asp?driveid=477
You will need an external USB hard drive to back up your existing hard drive.
It needs to be large enough to back up your existing drive.
Plug in the drive, Windows should recognize it.
Format the external hard drive so it is clean.
Backup Existing Drive
Back up drive C to the external drive using Windows Vista.
Go to Control Panel => Backup and Restore Center
Select the “Back-up files or your entire computer” option
Select “Back up computer
”Windows displays “Where do you want to save the backup”
Select “On a hard disk”
Windows displays hard drives available,
Select the drive you just plugged in
Click “Next”
Review the screen “Confirm your backup settings”
Windows displays “Local Disk (C) (System)” in the bottom window.
Click “Start backup”.
Backup will take 1-2 hours.
When completed, you have a complete image of your drive created by Windows Vista on the external HD
Install new Hard Drive
Shut down the machine.
Install the new hard drive per manufacturer instructions.
http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-62826
Boot the computer using the Vista CD.
Once files are loaded, Vista will open
Click “Next”
Click “Repair Your Computer”
Windows displays a window showing operating systems available, the window will be blank.
Click “Next”
Windows displays “Choose a Recovery Option”
Select “Windows Complete PC Restore”
Windows displays the saved image from your external drive
Click “Next”
Windows displays the restoration information
Click “Finish”
Remove the Windows CD
Restore will take 1-2 hours
Set up the new drive
After restoration, the system will reboot and you should be at the Vista Log In screen.
Log in normally and check to be sure your programs work.
You now need to tell Vista you have a new drive, and resize the partition to the capacity of the new drive.
Tell Windows to recognize the new drive
Start Menu, L click “Computer”
Drive C displays the stored image with the same capacity of the old drive.
R click on drive C => properties
Select the “Hardware” tab
Highlight drive C
Select the “Properties” tab, bottom right
Click on “Change settings”, bottom left
Click on the “Volumes” tab
Click the “Populate” tab
Windows will now populate the table with the settings for the new drive.
Save the settings and Reboot the computer.
Windows will now recognize the new higher capacity drive.
After reboot
Start Menu, R click “Computer”
Select “Manage”
In the L window, select “Storage” => “Disk Management”
Disk “0” is your new drive
Select Drive C
R click Drive C, select “Extend Volume”
The Extend Volume Wizard will open
Click “Next”
Click “Finish”
The new drive capacity is now operational.
You will now have two partitions, one for Windows, one for programs and data.

I'm also interested if anyone knows. I called the Square Group in London (Nex Oxford Street) but they said they'd get back to me ... but they didn't ...

MacBook Pro2012 : How can you get hard drive upgraded in Netherlands without losing warranty?

My MacBook Pro (2012) hard drive is almost full, Apple refuses to provide hard drive upgrade service, how can you get hard drive upgraded in Netherlands without losing warranty?

Dear Ralph, and All
My MBP is indeed non-retina.
I also have Apple care support for 3 years
I was in touch with Apple suport since last week. Response I got on Phone was pretty astounding (waiting email confirmation). They say following
- Apple support does not provide such service of upgrading hard drive
- Doing it yourself means you will lose warranty (due to nature of operation one would need to perform on the computer)
- None of authorised delars will provide such a service
So as such there apparantly is no way to get your hard drive upgraded without losing warranty.
Leaves me a bit perplexed
I do understand MBP retina (or iPAD / iPhones) are manufactured in way that makes it technically impossible to upgrade certain parts. But why non-retina MBP?
What do you all think? is this reasonable? is this what a MBP customer would expect?
Really appreaciate the quick responses i have recieved from you and others on this forum.
Many thanks
Tirath Shah

Need help picking the correct hard drive upgrade for my MBP

I need help picking the correct/best hard drive upgrade for my MBP. It is the 15" 2GHz Core Duo. Came with a spacious 90GB drive.
Suggestions and recommendations very appreciated.

It will take almost any 2.5 inch sata drive.
Take a look at www.newegg.com and www.macsales.com to see what's out there and how much it costs.
Toshiba have a 320gb 2,.5 inch drive in the works, but it's not quite out yet and will be expensive.
I'll start you off..
http://www.newegg.com/Store/SubCategory.aspx?SubCategory=380&name=Laptop-Hard-Dr ives

G5 Dual 2.0 Hard Drive removal issues (Top slot)

I must have an older G5 Powermac cuz the top hard drive is higher than the edge of the case, making it impossible to remove without some serious case deconstruction. the side screws on the sides that allow it to slide into the bay are keeping it from dropping down and sliding out. Does anyone have any suggestions on how to remove the top hard drive? Any online docs? I have searched and found nothing so far.

Hi miles loretta;
Now, now. Don't be so hard on yourself. This is how we learn.
I have to admit that when the drive in my PM Quad when bad it took me longer to get the drive then I care to talk about. Now we both know how to do it.
Allan

PowerMac G4 "Mirrored Drive Doors" 2x1GHz Hard Drive Upgrade

I have a PowerMac G4 "Mirrored Drive Doors" 2x1GHz with one 75 GB PATA hard drive.
I want to install two 500 GB PATA drives.
1) How is this done while transferring all the data from the 75 GB drive to the new drives?
2) Is a master/slave configuration the only option for two PATA drives?
Regards,
David

I prefer not to cut pin 28 wire so I’ll go with the master/slave (device 0/device1) configuration.
I do not know to what you refer. I have two 300 gig drives in my MDD, connected without modification to the cable (to which the original 80 gig was connected). The drive jumpers are set as cable select. Repeat - no modification of the cable was ever done. In fact, but this is from memory, I believe I could not boot from drives that were jumpered as "master" / "slave".
Can anyone confirm the number of PATA drives that will fit in a MDD?
As shipped, the MDD is wired for up to four hard drives. There are two cables and each will let you connect two drives. One of the buses is slower than the other - the faster one is where the original drive is located.
Are the bays under the CD/DVD drive set-up for SCSI drives?
No. You need a scsi card to use scsi drives.

Mac Pro 2.66 Dual Core Intel Xeon (April 2007) - Hard Drive Upgrade

My hard drive is making rather worrying clicking noises so I think it's time to (very quickly) pick up a new drive.
I'm a little confused about what kind of drive I should order. The drive it came with is a Seagate Barracuda ATA. Would anyone be kind enough to advise if I would be able to use an SATA II drive? I'm looking at the WD Caviar Black 1TB as they seem to have good reviews.
Any help would be greatly appreciated...

Please excuse my ignorance but when I look at my drive in about my Mac it says ATA. There wouldn't be any issues given this is an older Mac Pro from April 2007?
There is an ATA section in System Profiler (from "About This Mac"'s "More Info" button), but it for the optical drives. The hard drives are in the "Serial-ATA" section.

Powermac Dual 2.0Ghz hard drive upgrade

Similar Messages

Maybe you are looking for