PowerMac G5 DUAl 2.5Ghz and older ATA drives, HOW ?

Hi everybody.
I have question maybe someone could help me with.
I now have a G5 Dual 2.5 and also 3 ATA133 drives from my old G4. I need to install the 3 ATA133 drives into my G5, but from what i have read someware, the G5 uses another system, right ? its not ATA133 anymore.
So how is the easyest way to get my 3 ATA133 drives to work indside the G5 ?
Do i need a ATA133 controller card (PCI) or something else, does the G5 have PCI at all ?
If somebody could help me out here, i would be very happy indeed.
Thx a lot.
Mugge

This depends on which model of dual 2.5 you have. The dual processor 2.5 has PCI slots. The dual core dual processor 2.5 (quad) has PCI-Express slots. Both G5 models use SATA (Serial ATA) hard drives so you do need a controller card to attach your ATA drives.
Apple doesn't support mounting more than two hard drives internally in the G5s so it might be easier to just get firewire cases for your hard drives and make them all external.

Similar Messages

Networking a G5 dual 2.5ghz and a Powerbook G4/550 (Gigabit Ethernet)

I have two macs. A PowerMac G5 dual 2.5ghz with 2 gigs ram. My other one is a Powerbook G4/550 (Gigabit Ethernet)(with PCMCIA Slot). I have the G5 at my desk and the Powerbook upstairs (about 100 feet by walking 40 feet as the crow flies. I have a 115 year old house with unGodly thick mortar walls that make any networking a challenge so I do not want to guess. I want the best networking solution afordability wise and efficiency wise. Mobility is not that big of a deal and speed of data transfer is paramount. I also do not want slow download or transfer speeds on either machine. I don't transfer mush from BIG MAC to small mac but the internet thing (SPEED) is important. I do movie and music editing on both and maintain a web site daily with tons of each on it. Should I wire the thing to avoid slow wireless speeds and what all do I need. I know my laptop (Original Airport) speed is 11mbs. but I can't seem to find any comparison to ethernet wired speeds. I have DSL and no airport card and don't mind wiring if the speed is lots better. Can someone straighten me out or point me to the andwers? Please? indigorob

If speed is important then you want to run ethernet cable between the computers. The Mac's ethernet (10/100/1000) connector is capable of 10 megabits/second, 100 megabits/second, and 1000 megabits/second (Gigabit Ethernet). The original airport is about 11 megabits/second. The Airport Extreme/Express is 54 megabits/second.
You can easily get at least 100 megabits/second by running wired Ethernet.

Hi, I am going to buy a new iMac desktop. I am going for the 3.4GHz Quad-Core Intel i7, 16 GB RAM and 2TB ATA Drive. I want to know whether I should go for the dual drives option i.e including the 256 GB SSD. I do a lot of 'heavy' media work. Brian

Hi, I am going to buy a new iMac desktop. I am going for the 3.4GHz Quad-Core Intel i7, 16 GB RAM and 2TB ATA Drive. I want to know whether I should go for the dual drives option i.e including the 256 GB SSD. I do a lot of 'heavy' media work.

by looking at the specs the laptop is better but if your not a gamer or graphics designer then you most likly wont notice a difference in the performance at all so with that said a few downsides
the processor is i5 the i7 processor is the better processor the graphics card has half the dedicated memory that the laptop has and the hdd compared to the solid state is not much of a difference unless you wanna move your computer all the time you wont need a solid state drive
but like i said before if your not a gamer or graphics designer on your computer you will not notice the difference most likely

One IDE drive and one ATA drive in a single RAID enclosure?

I just got an OWC AL Elite dual-drive RAID enclosure, and was told, by OWC, that I could drop an IDE drive and an ATA drive into the enclosure and it would work fine.
It's not - If I unplug one of the drives, it works fine: the drive mounts and shows up in Disk Utility, but when both drives are plugged in, it doesn't mount, and Disk Utility sees the drive as a single 2TB drive (one drive is 300GB the other 160GB).
any thoughts? I have the jumpers on the drives set at Cable Select, I tried them both on Master and the drive wouldn't even show up in Disk Utility.
thanks

Yes. I have it. They sell a model for ATA drives and SATA drives. Go into the "external enclosures" section and scroll down about halfway. It's in the multi-drive section.

Powermac G5 dual 2.5GHz won't boot

Hi,
I've recently started having issues with my dual 2.5GHz G5 Powermac. When I switch it on I can hear the drives start up and data being read from them. But there's never any chime and the screen stays black. The drives stay quiet (spinning but no data being read). After a minute or two the fans ramp up to full speed.
If I leave it off for a while (eg. overnight) it resolves itself somehow and boots up without any issues. Once it's booted up there are no issues at all and it will run fine for weeks and days, until it needs to be rebooted again. I just put it to sleep when I'm not using it and it wakes up fine.
I've tried the following without any success:
- unplugging all peripherals (usb + firewire etc)
- reseating the ram
- swapping out the ram
- trying to boot into open firmware (it won't get that far)
- resetting the pmu with the button on the motherboard
- installed the latest updates to os x
- reseated the graphics card
- replaced the battery on the motherboard with a brand new one
This started roundabout the time I upgraded to 10.5.5 though that could be a coincidence. I also cleaned dust from the inside of the machine at that time as well (including off the graphics card fan and heatsink which was getting clogged up). So, that may have caused it. But again it could just be a coincidence.
Does anyone have any suggestions? All fans and both fans spin up, so I don't think it's the PSU, but I could be wrong. My only thought at the moment is a possible problem with one of the drives. So, I could try installing to a firewire drive and booting from that, but given that I can't even get into openfirmare, I'm not confident in that working. Similarly I don't have much hope of it booting from CD.
Any suggestions or help would be very much appreciated
Phil

Hi Phil Brayshaw-
What does the little white power light do? This should be helpful: About the Power Mac G5 (Late 2005) diagnostic LEDs
Although it sounds to me like you have tried most of the troubleshooting steps, this document is a good overall reference to address this particular problem: Power Mac G5: What to do if you see black, white, or no video at start up
Have you tried another monitor and/or double-checked your cable and its connections? If everything else is working as expected that would certainly be a major suspect.
Luck-
-DP

Using SATA and 2 ATA drives

I'm having some trouble getting the last ATA drive to be found, the normal primary ATA, as the sata drive has been set to primary.
Where can i set it so i can use it. can't really seem to find it.
Any help is more than welcome.

Assuming W2K or XP, set for
Native mode
SATA only (to boot from PATA) or PATA only (to boot from SATA)
SATA keep enabled - yes
PATA keep enabled - yes

I am trying to gather all of my music into one place, but it is scattered throughout my computer and external hard drive, how can I put it all in one folder and then create one library off of it?

My first problem is that I need to get all of my music files in one folder, they are scattered throughout my computer and external hard drive and I am trying to get them all together. Afterwards I want to send this music to my microsd hard in my Samsung Galaxy s4, is there a way to proceed through this? Or at least one part of it?

Consolidate your iTunes Library
As for the other part of the question, iTunes syncs with Apple devices.
Simply copy the media desired from the computer to the microSD card. This has nothing to do with iTunes.

Dual Band (5ghz and 2.4 ghz) Wireless Network Config and Dropped Connection

Hi, I have an Airport Extreme (802.11N) and a Motorola WR850G (802.11A/B/G) that I'm trying to connect in a dual band setup - but something in my setup is causing the Airport to drop it's connection (before the connection is dropped - everything works great). After I lose connectivity, both routers show up in my list of wireless networks, the light stays green, but I don't have local or internet access. When I try to reconnect, the log on times out. Also, the Airport isn't displayed in the Airport Utility (light is green on the airport itself though). Unplugging and resetting the Airport Allows all computers on the network to connect locally and to the internet for a few hours until the connection drops again. While it is up and running, I have no problems streaming movies off the connected Airdisk, navigating the internet, and connecting both N and G devices to the network.
I'd love to hear from you if you've gotten a similar setup to work, and if possible, have you provide the settings you used to make this work. I've looked around quite a bit and haven't seen a detailed description of the process (even from the Apple documentation). Also, advice from anyone would be greatly appreciated since my wireless networking knowledge is pretty basic.
My configuration:
Time Warner cable modem connected to the Airport's WAN port. WR850G connected by LAN port to Airport's LAN port. Bridge Mode check box selected on WR850G. Airport setup for 802.11n (5Ghz). Unique SSIDs to determine which network is 'N'. Same password for both networks. My Firmware and utilities are up to date.
Computers/Devices on Network:
Two Macs with Airport Extreme N cards. A Vista PC with a D-link N card (only compatible with 2.4 Ghz so it connects to the G network). A Vista PC with a GB ethernet card connected to the Airport Extreme. Various other G devices like iPod touches and an old iBook. Airdisk connected to the Airport Extreme.
Thanks,

I removed the second router (Moto wr850g) and everything seems to be working smoothly. It must be some settings on that one that are causing the problem, but I haven't been able to get it configured correctly. I noticed there were some IP conflicts with my wireless wanting to use the old Moto router IP and trying to assign my Mac an IP from that router. Does anyone know specifically what needs to be disabled on a router in bridge mode? Since I have a third party router there aren't any handy wizards that can configure it for me.
Thanks again

PowerMac G5 Dual 2.5GHz Remote Power Button ??

Hi,
I'm moving a G5 to a place where it would be hard to get to the power button. Is there any way to add a remote power button?? Any help would be great thanks.

Hi Ampex351-
Did you by any chance search the forum regarding this subject? I know that this has come up more than once and the most eloquent solution seems to require a small amount of surgery on your Mac in order to install the contacts of a small 12V relay in place of the power button and have that switched from a remote location via the application of 12V.
Luck-
-DP

MSI K7N2 Delta ILSR and Serial ATA Drive

I've got a very strange problem....
Yesterday i have installed my new motherboard (MSI K7N2 Delta ILSR) but i have a problem with the SATA feature.
I've got two drives : one 40GB ATA (Western Digital) and one 160GB SATA also from Western Digital.
My SATA drive is recognized by the FastTrak BIOS (v2) but i'm unable to reinstall Windows XP Professional (with SP2 Slipstreamed) because Windows Setup didn't recognize the SATA disk. I have loaded the Promise Serial ATA Drivers at the begin of the installation (F6)...
I have also tried 2 different versions of the Promise SATA Drivers; the one that cames with my motherboard CD, and the most recent from the MSI website. But with both drivers the same result. How can i get my Serial ATA Harddisk get work with this motherboard?
Any help will be appreciated.
Thanks,
Computerfreakje.
PS : My specifications are the following:
MSI K7N2 Delta ILSR (Rev. 7.4)
AMD Athlon XP 2500+
2x 256MB Kingston PC3200 Dual Channel
ATI Radeon 9800 Pro 128mb (R360)
Western Digital 40GB ATA
Western Digital 160GB SATA

Thanks for your reply Richard,
My motherboard didn't came with a floppy (I have bought an bulk version..) I have created a SATA floppy by myself. (I have got the drivers from the motherboard cd..) These drivers are also good, right?
Which type of RAID Array should i create? Because i have only one SATA drive.....
I think the "auto" feature is the easiest way?
Thanks.
Computerfreakje.

Tried to replace RAM but now computer not starting...PowerMac G5 dual 2.0 - are my hard drives safe? What's up?

Hello - I tried to increase the RAM in my old and trusted Power Mac G5 (dual 2.0...2005) tonight and now I'm in trouble. It has only 4 slots for RAM. It came installed with 2X256 and 2X512 ram cards. I bought 2X 1GB of Ram from Crucial.com after sending them the specs of my computer they assured me it was the right RAM. I installed the RAM just how the youtube tutorials instructed.... I replaced the 2 256 cards with the new 1GB cards and closed up the computer......note: I also "dusted" the inside of the mac very carefully and lightly with a barely damp rag.....
I plugged her in and the power button light immediately went on but the computer did not. The button wouldn't respond to being held down either. No sign of a startup or a fan noise. Nothing on the screen, no signal.... Nothing..... So I tried reversing the order of the RAM, I installed the 1GB along with the 512's. Nothing again, just the light turns on when I plug her in. Then I returned the RAM to the original configuration.....again NOTHING...just the light on.
I reset the SMU. (little button underneath the RAM area) I haven't tried to reset the PRAM yet, but I'm pretty sure that will not work either as she is not starting up at all....just the light is on... I didn't get a noticeable shock or static spark during the entire operation either. ****....whats up?
Are my Hard Drives safe in there?
Any ideas out there? Thanks in advance to your advice, T

ToddMusic wrote:
note: I also "dusted" the inside of the mac very carefully and lightly with a barely damp rag.....
Are my Hard Drives safe in there?
Any ideas out there? Thanks in advance to your advice, T
Ouch! That was not the way to get dust out. Running that damp rag anywhere near an electronic component, even if you were wearing a properly grounded writs strap, was way dangerous.
Did you lay the machine on its left side when you replaced the RAM? That is much safer (though the recommendation only shows up in the service documentation, not the user guide, for some reason).
What I would do at this point is to remove all RAM and try to power the machine. If other stuff is OK, you won't start but you will see the lunar LED flashing in a repetitive pattern above the power switch. If you don't see that happening, then things are exceptionally serious.

I have lightroom 5 and no dvd drive how do I install

How do I install lightroom 5 without a DVD player? I have disk and number.

Download from Adobe
Mac: Adobe - Lightroom : For Macintosh : Adobe Photoshop Lightroom 5.7.1
Win: Adobe - Lightroom : For Windows : Adobe Photoshop Lightroom 5.7.1

I want to wipe my computer files and empty the drive, how do i do this?

I want to empty my computer of all data and files. How do I do this?

Hello,
Could you be hitting the key combo of Control+Eject, (F12), perchance?

PowerMac G4 Dual 1.25Ghz won't let me install updates to Leopard

Hi there.. I just bought a PowerMac G4 Dual 1.25Ghz and for some reason, I can't install Leopard through the DVD drive. I get an error saying something about <Base System> and when I did install it leopard by making the powermac a firewire drive, now I can't do any updates. I get a message that the file is corrupt and contact the software vendor. I tried doing a Repair Permission, but it wont do it and keeps going and going.... Has anyone had any issue like this?

First, did you install Leopard using a retail version installer. Using an installer from another Mac model won't work.
Second, is this the update file you tried to use? http://support.apple.com/downloads/MacOS_X_10_5_8_ComboUpdate
It's best to download the update file & install off line, rather than use the auto update feature. Repair permissions before & after installing the update.
 Cheers, Tom

Difference between ULTRA ATA and SERIAL ATA

Hello,
What is the difference between ULTRA ATA and SERIAL ATA ?? Is the connector different for each type ?? Thanks in advance.
Robert Lespérance

Was wondering why you are considering a ATA drive? The iMac G5 als has a serial ata drive already.
If you are considering an external drive, then you have a problem. The most important thing there is that you get a drive with firewire interface because I think they are the fastest, but USB is an ok choice. If there is an external firewire drive that also uses a serial ATA drive inside of it, then that would be an excellent choice for speed. USB or Firewire are standards for connecting a peripherial to you Mac. An external drive will probably have a very common, read Mactor, WD, Seagate, ATA drive in it. The external drive case has a interface inside of it which allows USB or Firewire to speak with the ATA drive, any flavor. Some people just purchase a powered external 3 1/2 case and install the hd they like the best, that is the nice thing about standards.
I think serial ATA will pretty much spell the end of all of the older ATA drives. The serial drives are actually very competitive in price now and faster.
Suggest you go to Western Digital, Maxtor, and/or Seagate's web sites to learn what drives they offer.
iMac G5 17" ALS with 1 Gigglebyte ram Mac OS X (10.4.4) Also a homebuilt Sempron, a Compaq, and a Dell laptop...oh my!
iMac G5 17" ALS with 1 Gigglebyte ram Mac OS X (10.4.4) Also a homebuilt Sempron, a Compaq, and a Dell laptop...oh my!

PowerMac G5 DUAl 2.5Ghz and older ATA drives, HOW ?

Similar Messages

Maybe you are looking for