PowerMac G5 hangs after going into screen saver power save mode

I have a PowerMac G5 and it's been working fine, but as of late has been hanging. I had a couple of external disks on the machine ( Maxtor OneTouch II and a OneTouch III). I recently added two more OneTouch III and stripped the three OneTouch III's together in a RAID set. I'm wondering if that is causing the hangs, but I've also seen it hang without the RAID so I'm not convinced it's the RAID.
Anyway, I can't figure out what's causing it to hang, but it seems to hang at some point after the screen saver runs and then the screen goes into power saver mode. It's not hung right when it shuts down the monitor, but at some point after that.
When it gets in this mode, I can't remotely login using ssh and I can't seem to wake it up. What I end up having to do is to hold the power button down for several seconds until the machine powers off.
In an attempt to see what's going on, I set the OS X monitor power save mode to "never", but I don't think I left it that way long enough and I never saw it hang.
Does anyone have any debugging tips that would help me identify the culprit?

I've been having the same troubles lately. Seem
since the JAVA update. It hangs completely after the
screen is shut down. Every morning I have to reboot
with the power button.
I am also joining the crowd with this issue. I have a 15" Powerbook G4 that has acted normally until recently. Not sure exactly when it started, but about the same time as the recent updates. Similar behavior to the previous forum posts.
When I manually put the laptop to sleep it freezes up before it sleeps and the multi-language reboot warning comes up. This also happens if it is set to auto-sleep after xx minutes.
When I try to wake it up, the screen is black and the power light shows it is on and it never unfreezes or I get the reboot message.
I have tried everything I can think of to troubleshoot this. I just re-installed the 10.4.8 update over the exisiting one (using an external boot drive made with SuperDuper) and it still happens... BUT when I put the laptop to sleep with the startup drive being external, it seemed to behave properly. I can't figure this out since the external clone was made only minutes earlier from the laptop... and it works. I have zapped PRAM, and done the battery removal / power button reset.
Below is the "report" I have been getting - and sending to Apple. They must be getting tired of the many I have sent.
Any thoughts out there?
Thanks.
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x0000000000000020 PC=0x00000000002FA2A4
Latest crash info for cpu 0:
Exception state (sv=0x32E70000)
PC=0x002FA2A4; MSR=0x00009030; DAR=0x00000020; DSISR=0x40000000; LR=0x002E31B0; R1=0x1793BCD0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x002E31B0 0x002AE920 0x002F2EF4 0x0003C884 0x000A9314
Proceeding back via exception chain:
Exception state (sv=0x32E70000)
previously dumped as "Latest" state. skipping...
Exception state (sv=0x2D24BC80)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): 0x300 - Data access
Latest stack backtrace for cpu 0:
Backtrace:
0x00095138 0x00095650 0x00026898 0x000A7E04 0x000AB780
Proceeding back via exception chain:
Exception state (sv=0x32E70000)
PC=0x002FA2A4; MSR=0x00009030; DAR=0x00000020; DSISR=0x40000000; LR=0x002E31B0; R1=0x1793BCD0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x002E31B0 0x002AE920 0x002F2EF4 0x0003C884 0x000A9314
Exception state (sv=0x2D24BC80)
PC=0x00000000; MSR=0x0000D030; DAR=0x00000000; DSISR=0x00000000; LR=0x00000000; R1=0x00000000; XCP=0x00000000 (Unknown)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
Model: PowerBook5,8, BootROM 4.9.5f3, 1 processors, PowerPC G4 (1.5), 1.67 GHz, 1 GB
Graphics: ATI Mobility Radeon 9700, ATY,RV360M11, AGP, 128 MB
Memory Module: SODIMM0/J20STANDARD, 1 GB, DDR2 SDRAM, PC2-4200S-444
AirPort: AirPort Extreme, 405.1 (3.90.34.0.p18)
Modem: Jump, , V.92, Version 1.0,
Bluetooth: Version 1.7.8f2, 2 service, 0 devices, 1 incoming serial ports
Network Service: Built-in Ethernet, Ethernet, en0
PCI Card: pci106b,4318, sppci_othernetwork, SLOT-A
PCI Card: TXN,PCIXXXX-00, cardbus, PC Card
PCI Card: usb, usb, USB20
PCI Card: usb, usb, USB20
PCI Card: usb, ehci, USB20
Parallel ATA Device: Hitachi HTS721010G9AT00, 93.16 GB
Parallel ATA Device: MATSHITADVD-R UJ-846,
USB Device: Bluetooth HCI, , Up to 12 Mb/sec, 500 mA
USB Device: Apple Optical USB Mouse, Mitsumi Electric, Up to 1.5 Mb/sec, 500 mA
USB Device: Apple Internal Keyboard / Trackpad, Apple Computer, Up to 12 Mb/sec, 500 mA
15" G4 PowerBook 1.67 Mac OS X (10.4.8)
G5 2.7 Gig Mac OS X (10.4.4) 3 Gig ram
15" G4 PowerBook 1.67 Mac OS X (10.4.8)

Similar Messages

When I start up my new Imac with my password, it works but after going into sleepmode, I can't go out of the sleep moed with this password

I did the configuration of my new Imac and entered and confirmed my password when asked.
When my computer is switched of, I can startup with this password but after going into sleepmode, this password doesn't work.
The same when I go to "system preferences" users & groups, it's not possible to unlock the lock with this password
I'm sure that I never used another password.

If Apple was the one that replaced the ribbon cable, return it. If not, run AHT (Apple Hardware Test).
Using Apple Hardware Test to troubleshoot a hardware problem
Your issues might be caused by a hardware problem. Running Apple Hardware Test can help you solve this problem by showing you the faulty hardware.
Shut down the computer by going to Apple () > Shut Down…
Select Shut Down or allow the computer to shut down automatically.
Plug in the MagSafe power adapter into a power source and then connect it to your Mac if you have not already done so.
Press the Power Button to turn on the computer.
Press and hold the D key on the keyboard before the grey starting screen appears.
Continue to hold the D key until the loading screen shows up. You should see a globe.
When AHT has loaded, select your Language and then press the Return (↩) key.
Select the Perform Extended Testing checkbox located under the Test button.
Press the T key, select the Test button, or press the Return (↩) key to start running the diagnostics.
Report any issues it shows in a reply.
I hope I helped.

HP Envy shutting down after going into sleep mode

Hi. I'm not sure where to post this so I'll try it here.
My laptop shut downs automatically when it goes into sleep mode. Not right away when going into sleep mode. Maybe like an hour later after going into sleep mode.
I'm not sure it's overheating because it never shuts down while I'm actually using the laptop.
Do you guy have any idea how to fix this?
Product name and number: HP ENVY TouchSmart Sleekbook 4-1115dx
Operating System: Window 8
Error Message: None
Any changes to your system before problem occurred: No

Hey Tecmo_SB_Guy,
I would suggest you take a look at advanced power settings. It can seem like the notebook is turning off when it is actually just hibernating. You can set it to not hibernate.
1. Windows key + Q to open the Search Bar
2. Type "power"
3. Click Settings under the Search Bar
4. Select Power Options from the results on the left.
5. In Power Options, Click Change when the computer sleeps, on the left.
6. Set the Put the computer to sleep setting so that it fits your usage best.
7. Click Change advanced power settings, at the bottom.
8. Expand Sleep and expand Hibernate after. If you want you can change the hibernation setting to Never by typing "Never" into the minutes field. See attached picture. You can do this for battery and/or plugged in.
9. Click Apply to save changes.
If you don't already shut it down periodically, I would suggest shutting it down at least 2-3 times a week if you use it daily. Leaving the computer running continuously can shorten its lifespan. Hard drive failures and motherboard issues are seen much more often on machines that are left running constantly. Computers get bogged down and run slowly when the memory is full. Memory only clears out and resets itself when the computer is shut down. Here is a link explaining more about memory accumulation and hardware aging.
I hope these suggestions help! Please let me know if you have any questions
Attachments:
PowerHibernateNever.jpg ‏59 KB

I am trying to import my cd's onto itunes on a new macbook pro. i can import the cd fine but can not get track names or album art work. after going into advanced it is just coming up with "CDDB information not available"

i can import the cd fine but can not get track names or album art work. after going into advanced it is just coming up with "CDDB information not available"
thank you

Use the trackpad to scroll, thats what it was designed for. The scroll bars automatically disappear when not being used and will appear if you scroll up or down using the trackpad.
This is a user-to-user forum and most people will post on here if they have problems. You very rarely get people posting to say there update went smooth. The fact is the vast majority of Mountain Lion users will not be experiencing any major problems with the OS, or maybe with apps which are not compatible, but thats hardly Apple's fault if developers don't update their apps.

Do I need to visit the Apple store since I do Not see the software update line, after going into setting?

Cannot locate the software update line, after going into settIngs on my IPad2. Did I miss something?
Help, need to upgrade to a minimum of IOS5
THANKS

You only have the option of you are already running iOS 5 already. If you are trying to update to iOS 5, you have to use iTunes on a computer to update the iPad.
Here are the instructions.
http://support.apple.com/kb/HT4972
Or you can connect the iPad to the computer, launch iTunes. Select the iPad under the devices heading on the left, click on the Summary tab and then click on Check for Update
You will only be able to update to iOS 6 now.

Bluetooth Audio dropping out when Phone goes into screen lock

I have a 3G running 3.0 and a Sony Bluetooth audio capable car stereo. The audio streams perfectly via bluetooth until the phone goes into screen lock or "sleep ", at which time the audio starts drooping out. As soon as you slide to unlock the screen everything works fine again.
Anyone else with this issue ?

Yup, that's exactly what I've had.
I paired a Jabra BT3030 BlueTooth stereo headset module to my 3G and it worked perfectly until the screen went off and then the audio could only be heard intermittently. When the screen came back on, audio was perfect again. This was completely repeatable.
I posted about this the other day, but just prior to that tried again to confirm and I could NOT get it to occur. No matter how many times I put the iPhone to sleep and woke it up, the audio played consistently with NO dropout which is somewhat frustrating and a bit bizarre.
Looks like there is an issue with A2DP if several of us are experiencing the same problem so bug report/feedback to Apple is required I think.
Has anyone else had the problem go away next time you try?

What do I do if an iPod shuts down after going into sleep mode

My friends iPod keeps shutting down after it goes into sleep mode. I just fixed it up (restored it, had to dry it out after it fell into water) and now it does that. Everything else works fine but if I put it in sleep mode or put it into sleep mode it shuts down. How do I fix this because I've never seen this happen before.

Hey Tecmo_SB_Guy,
I would suggest you take a look at advanced power settings. It can seem like the notebook is turning off when it is actually just hibernating. You can set it to not hibernate.
1. Windows key + Q to open the Search Bar
2. Type "power"
3. Click Settings under the Search Bar
4. Select Power Options from the results on the left.
5. In Power Options, Click Change when the computer sleeps, on the left.
6. Set the Put the computer to sleep setting so that it fits your usage best.
7. Click Change advanced power settings, at the bottom.
8. Expand Sleep and expand Hibernate after. If you want you can change the hibernation setting to Never by typing "Never" into the minutes field. See attached picture. You can do this for battery and/or plugged in.
9. Click Apply to save changes.
If you don't already shut it down periodically, I would suggest shutting it down at least 2-3 times a week if you use it daily. Leaving the computer running continuously can shorten its lifespan. Hard drive failures and motherboard issues are seen much more often on machines that are left running constantly. Computers get bogged down and run slowly when the memory is full. Memory only clears out and resets itself when the computer is shut down. Here is a link explaining more about memory accumulation and hardware aging.
I hope these suggestions help! Please let me know if you have any questions
Attachments:
PowerHibernateNever.jpg ‏59 KB

I purhased an apple usb cd/dvd and I have a cd disk that won't eject even after going into controls and selecting disk eject any ideas how I can take of the issue?

I have a cd disk stuck in my USB super drive, it won't eject even after going to control and selecting eject disk

Hi BCservant,
Welcome to the Apple Support Communities!
I know that it can be concerning when you cannot eject a disk from your external drive. There are a few troubleshooting steps that I would recommend to help you get this situation resolved. Please use the attached article for troubleshooting information.
Get help with the slot-loading SuperDrive on your Mac computer - Apple Support
Doesn't eject discs or discs eject slowly
If the drive ejects discs slowly or appears to be struggling, insert and eject a single disc several times. Check the disc to see if it has a label or other material stuck to the disc that increases the thickness. Remove the label if possible.
If the disc will not eject, try pressing the eject key on the keyboard. Some older keyboards may use the F12 key to eject discs.
If the disc will not eject, try dragging the disc icon to the trash.
If the disc will still not eject, try holding down the trackpad or mouse button after restarting the computer. The Superdrive should attempt to eject the disc.
If the disc continues not to eject, reset the System Management Controller (SMC) and try steps 1-4 again.
If the disc still does not eject, contact Apple or an Apple Authorized Service Provider, or make an appointment with an Apple Retail Store for additional assistance.
Best regards,
Joe

Pavilion H8 - 1240T goes blank due to power saver settiing ?

ok a while back I was having this same problem where my H8 - 1240T was going to a blank screen..... the fix was to completely turn off any screensaver and sleep mode..... blank screen/total freeze problem has come up when I stupidly tried to experiment with some power saving mode settings and now I can't get the screen to stay on for more than 5 minutes ! Multiple boots bring up a blank screen even though there are no error beeps when the computer powers on.... after an overnight shut down I am able to boot up into Windows 7 to try and turn off all power saver settings but the screen eventually goes blank...... in the past HP tech support has been unable to pin the problem down so I am asking if anyone has experienced this same situation and what the fix is..... I have an image of my hard drive when things were working good but I'd like to fix it without having to reinstall..... I'm thinking this is some sort of driver problem/conflict with the Nvidia card. I'd like to someday be able to use a screensaver with this machine !

Hi bigollo,
I saw your post and I will be happy to help. There is definitely something going on with the graphics card and/or drivers. Let's start by checking the hardware. Below is a document about how to use the HP Diagnostic Tools. I would do the System Check – Extensive Check and under Components do the Video Test.
Testing for Hardware Failures Windows 7:
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&dlc=en&docname=c01443317&lc=en&jumpid=reg_r1002_us...
If you are using the standard graphic card that came with the Pavilion here is the driver for it below.
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=cp-103282-1&cc=us&dlc=en&lc=en...=
Thank you,
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

Nokia N8 Screen Saver & Power-Saving Mode

Few issues after 24hrs of N8 usage...
1) My Screen Saver stopped working... screen stays lit indefinitely, even when locked... after multiple restarts and lots of frustration it came back, but this issue has already happened twice - surely a bug
2) Power-Saving mode doesn't really make sense unless it is customisable... I am on a 3G only network, power-saving enables GSM-only... see the flaw?
Appreciate your feedback,
Mike

Regarding ISSUE #1 (the screensaver failure), I have a PERFECT solution!!!
However, I am not sure if this will work for you, because I have SPB Mobile Shell, but it is worth a try!
1) Make sure you have the widget for the MUSIC PLAYER on one of your main operating page.
2) Turn OFF your phone regularly. (NO NEED to hard rest by hold over 8 secs)
3) Turn ON your phone.
4) Once the phone loaded up, immediate play any song through your music player. (Need to be done before your phone auto-locks)
5) Lock your phone with your side-lock button; your screensaver should come back.
Both my g/f & I owns a Nokia N8, and we both experienced the screensaver failure problem. My N8 was easy to fix by many people's solution of just simply reset, and it automatically fixed the problem. But My g/f's N8 was stubborn, and wouldn't turn the screensaver back on by this simple reset method. Later I discovered the above method, and it worked every time! I think somehow the music player is triggering the screensaver and forces it to stay on.
Well, although we somehow surpass this issue, but Nokia still need to fix this problem. Nokia N8 is a great phone, it shouldn't have such a simple mistake in it. This makes the perfect phone imperfect!!! Anyway, please let me know if this method works for you guys, thanks.

6120 - Blank screen in power saver mode

Hi everybody!
I have recenty become a proud 6120 owner (my first symbian :-)), and I have 1 question:
how can I prevent in power saver mode, my screen to go complety blank??? I would like to see the status of my phone (time, missed calls, messages, etc.)!
this is really annoying!
can anybody help me, how to change/prevent this?
many thx in advance
daniel

In menu/settings/themes/powersaver I have to tick one of three options (time/date, text or animation). Whichever is ticked I get at least the clock in powersaver mode. Events show under the date (or text if you choose text) so keypad locked has a symbol, missed calls have a number (of missed calls) and a symbol and so on.
However I have also noticed the screen is totally blank after a while and pressing a button starts the powersaver cycle again - briefly showing the dark main screen (including missed call message etc) before showing the clock with the symbols for a short while again. The time it takes to enter powersaving mode is in the display settings but I can't see a setting for how long it shows for.
Why the clock etc doesn't stay I do not know - I presume even this would eat the batteries more than strictly necessary. I can't see any option to keep it but it may there somewhere!!

N80 Radio interference with screen saver/power sav...

Hi all,
When listening to the Radio, (with Nokia's supllied ear phones), I can here distortion/interference. Has anyone heard this? When i press a key on the phone the noise goes away. I am convinced it's the screen saveer or power save functions thar cause it.
Anyone else had this?
Cheers!
Dave

09-Jul-2006
11:00 PM
mr_rolfi wrote:
Hi all, When listening to the Radio, (with Nokia's supllied ear phones), I can here distortion/interference. Has anyone heard this? When i press a key on the phone the noise goes away. I am convinced it's the screen saveer or power save functions thar cause it. Anyone else had this? Cheers! Dave
Yes, I have the same problem. Very annoying as the radio is otherwise very good. (As is mp3 playback.)Has anyone updated the firmware and noticed an improvement?

DMP edge 340 going into sleep or soft off mode

Is there any information available on what might cause an Edge 340 to go into sleep or soft off mode, and how to recover them, short of power cycling?
thank you

Hello mflanigan021,
Wake on LAN should bring it out of sleep mode. It needs to be enabled on the Edge 340 dmp.
Take a look at the bug below. It doesn't reference sleep mode, but it does reference no output.
Edge 340 Monitor Auto Detect issue
CSCur85499
Hope this helps.

Time Machine crashes every time after the computer sleeps or goes into screen saver for a period of time

Time Machine works for me about 90% of the time, until I leave the computer alone for over a hour it seems and gets into the late screen saver stage or goes to sleep. After it does this Time Machine will not work, yet the hard drive is still fully fuctional. Please Advise.

Time Machine works for me about 90% of the time, until I leave the computer alone for over a hour it seems and gets into the late screen saver stage or goes to sleep. After it does this Time Machine will not work, yet the hard drive is still fully fuctional. Please Advise.

Computer freezes after going into sleep mode

My computer freezes after being left idle and I am prompted to restart. I have the screen saver set to view the nature pictures, but that doesn't show. The screen goes blank and then I have to restart. I've read about sleep problems, but not a solution. Have any? Thanks! ~M
Dual 867 G4 Mac OS X (10.4.3)

Hello Dean,
Yes, the restart prompt looks like the kernel panic alert screen. And I did accesss the panic.log and it doesn't mean much to me! Here is what I copied from the two crashes today:
Mon Dec 12 11:19:08 2005
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x0000000000000008 PC=0x000000000012C76C
Latest crash info for cpu 0:
Exception state (sv=0x2D53AA00)
PC=0x0012C76C; MSR=0x00009030; DAR=0x00000008; DSISR=0x40000000; LR=0x0012C7A4; R1=0x177439D0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x0012C7A4 0x0012E020 0x0012F4A4 0x0012D310 0x0012F014 0x0028FDA8
0x00281698 0x0027D238 0x0027CF74 0x002A9BF4 0x000ABE30 0x00000000
Proceeding back via exception chain:
Exception state (sv=0x2D53AA00)
previously dumped as "Latest" state. skipping...
Exception state (sv=0x3C5FC780)
PC=0x9001452C; MSR=0x0000F030; DAR=0xE07FF000; DSISR=0x42000000; LR=0x0000CFAC; R1=0xF0080040; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.3.0: Mon Oct 3 20:04:04 PDT 2005; root:xnu-792.6.22.obj~2/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): 0x300 - Data access
Latest stack backtrace for cpu 0:
Backtrace:
0x00095698 0x00095BB0 0x0002683C 0x000A8304 0x000ABC80
Proceeding back via exception chain:
Exception state (sv=0x2D53AA00)
PC=0x0012C76C; MSR=0x00009030; DAR=0x00000008; DSISR=0x40000000; LR=0x0012C7A4; R1=0x177439D0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x0012C7A4 0x0012E020 0x0012F4A4 0x0012D310 0x0012F014 0x0028FDA8
0x00281698 0x0027D238 0x0027CF74 0x002A9BF4 0x000ABE30 0x00000000
Exception state (sv=0x3C5FC780)
PC=0x9001452C; MSR=0x0000F030; DAR=0xE07FF000; DSISR=0x42000000; LR=0x0000CFAC; R1=0xF0080040; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.3.0: Mon Oct 3 20:04:04 PDT 2005; root:xnu-792.6.22.obj~2/RELEASE_PPC
Mon Dec 12 12:44:48 2005
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x0000000000000008 PC=0x000000000012C76C
Latest crash info for cpu 0:
Exception state (sv=0x2D53AA00)
PC=0x0012C76C; MSR=0x00009030; DAR=0x00000008; DSISR=0x40000000; LR=0x0012C7A4; R1=0x177439D0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x0012C7A4 0x0012E020 0x0012F4A4 0x0012D310 0x0012F014 0x0028FDA8
0x00281698 0x0027D238 0x0027CF74 0x002A9BF4 0x000ABE30 0x00000000
Proceeding back via exception chain:
Exception state (sv=0x2D53AA00)
previously dumped as "Latest" state. skipping...
Exception state (sv=0x3C5FC780)
PC=0x9001452C; MSR=0x0000F030; DAR=0xE07FF000; DSISR=0x42000000; LR=0x0000CFAC; R1=0xF0080040; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.3.0: Mon Oct 3 20:04:04 PDT 2005; root:xnu-792.6.22.obj~2/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): 0x300 - Data access
Latest stack backtrace for cpu 0:
Backtrace:
0x00095698 0x00095BB0 0x0002683C 0x000A8304 0x000ABC80
Proceeding back via exception chain:
Exception state (sv=0x2D53AA00)
PC=0x0012C76C; MSR=0x00009030; DAR=0x00000008; DSISR=0x40000000; LR=0x0012C7A4; R1=0x177439D0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x0012C7A4 0x0012E020 0x0012F4A4 0x0012D310 0x0012F014 0x0028FDA8
0x00281698 0x0027D238 0x0027CF74 0x002A9BF4 0x000ABE30 0x00000000
Exception state (sv=0x3C5FC780)
PC=0x9001452C; MSR=0x0000F030; DAR=0xE07FF000; DSISR=0x42000000; LR=0x0000CFAC; R1=0xF0080040; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.3.0: Mon Oct 3 20:04:04 PDT 2005; root:xnu-792.6.22.obj~2/RELEASE_PPC
I'll check into Dr. Smoke's FAQ, and see if I can decipher any of it.
Let me know what the above text means to you.
Thanks again~
Michelle
Dual 867 G4 Mac OS X (10.4.3)

PowerMac G5 hangs after going into screen saver power save mode

Similar Messages

Maybe you are looking for