Poweron from sc men�

Dear all
I have V240 which is not comming up.
By feeding the server we get the green led on the feeding, but then, when we push the starting buttom or we make the poweron control from the sc menu, the led becomes green and it is nomore possible to access the menu ok,this because if we make the console -f control, or break and then console, the menu remains always sc. The problem might be owed to the fact that one cannot set up the poweron. Is anyone able to help me?
Please see follows:
ALOM BOOTMON v1.5.4
ALOM Build Release: 008
Reset register: e0000000 EHRS ESRS LLRS
ALOM POST 1.0
Dual Port Memory Test, PASSED.
TTY External - Intern
TTY External - Internal Loopback Test, PASSED.
TTYC - Internal Loopback Test, PASSED.
TTYD - Internal
TTYD - Internal Loopback Test, PASSED.
Memory Data Lines Test
Memory Data Lines Test, PASSED.
Memory Address Lines Test
Slide address bits to test open address lines
Test for shorted address lines
Memory Address Lines Test, PASSED.
Memory Parity Test
Memory Parity Test, PASSED.
Boot Sector FLASH CRC Test
Boot Sector FLASH CRC Test, PASSED.
Return to Boot Monitor for Handshake
ALOM POST 1.0
Status = 00007fff
Returned from Boot Monitor and Handshake
Clearing Memory Cells
Memory Clean Complete
Loading the runtime image...
SC Alert: SC System booted.
Sun(tm) Advanced Lights Out Manager 1.5.4 (pgw1)
Full VxDiag Tests
BASIC TOD TEST
Read the TOD Clock: WED NOV 07 09:42:33 2007
Wait, 1 - 3 seconds
Read the TOD Clock: WED NOV 07 09:42:35 2007
BASIC TOD TEST, PASSED
ETHERNET CPU LOOPBACK TEST
50 BYTE PACKET - a 0 in field of 1's.
50 BYTE PACKET - a 1 in field of 0's.
900 BYTE PACKET - pseudo-random data.
ETHERNET CPU LOOPBACK TEST, PASSED
Full VxDiag Tests - PASSED
Status summary - Status = 7FFF
VxDiag - - PASSED
POST - - PASSED
LOOPBACK - - PASSED
I2C - - PASSED
EPROM - - PASSED
FRU PROM - - PASSED
ETHERNET - - PASSED
MAIN CRC - - PASSED
BOOT CRC - - PASSED
TTYD - - PASSED
TTYC - - PASSED
MEMORY - - PASSED
MPC850 - - PASSED
sc> showlogs
Log entries since NOV 07 09:42:33
NOV 07 09:42:33 pgw1: 00060003: "SC System booted."
NOV 07 09:42:43 pgw1: 00060000: "SC Login: User admin Logged on."
sc> swohowsc
Advanced Lights Out Manager v1.5.4
parameter value
if_network true
if_modem false
if_emailalerts false
sys_autorestart xir
sys_bootrestart none
sys_bootfailrecovery none
sys_maxbootfail 3
sys_xirtimeout 900
sys_boottimeout 900
sys_wdttimeout 60
netsc_tpelinktest true
netsc_dhcp false
netsc_ipaddr 0.0.0.0
netsc_ipnetmask 255.255.255.0
netsc_ipgateway 0.0.0.0
mgt_mailhost
mgt_mailalert
sc_customerinfo
sc_escapechars #.
sc_powerondelay false
sc_powerstatememory false
sc_clipasswdecho true
sc_cliprompt sc
sc_clitimeout 0
sc_clieventlevel 2
sc_backupuserdata true
sys_eventlevel 2
ser_baudrate 9600
ser_parity none
ser_stopbits 1
ser_data 8
netsc_enetaddr 00:14:4f:5b:ff:e3
sys_hostname pgw1
sys_enetaddr 00:14:4f:5b:ff:da
sc> showplatform
SUNW,Sun-Fire-v210
Domain Status
pgw1 OS Standby
sc> showenvironment
=============== Environmental Status ===============
System Temperatures (Temperatures in Celsius):
Sensor Status Temp LowHard LowSoft LowWarn HighWarn HighSoft HighHard
CPU temperature information cannot be displayed when System power is off.
MB.T_ENC OK 25 -6 -3 5 40 48 51
Front Status Panel:
Keyswitch position: NORMAL
System Indicator Status:
MB.LOCATE MB.SERVICE MB.ACT
OFF OFF OFF
Disk Status information cannot be displayed when System power is off.
Fan Status information cannot be displayed when System power is off.
Voltage Rail Status information cannot be displayed when System power is off.
Power Supply Indicators:
Supply Active Service OK-to-Remove
PS0 OFF OB OFF
Power Supplies:
Supply Status Underspeed Overtemp Overvolt Undervolt Overcurrent
PS0 OK OFF OFF OFF OFF OFF
Current sensor information cannot be displayed when System power is off.
sc> bootmode diag
sc> poweron
sc> console
Enter #. to return to ALOM.
sc> break
Break command is disabled when system is powered off.
sc> reset -y

Hi,
Please check in the Table whether attachment is there
BBP_PDATT in the File name
Enter the GUID in this table. Get the GUID from the T.code: BBP_PD
G.Ganesh Kumar

Similar Messages

ZEN Vision:M problem selecting from the men

Just like the title says, I'm having trouble accessing any of the menus(photos,videos,extras, etc..) from the menu on my ZEN Vision:M. I've tried pressing the touchpad to select a menu option but no luck, I've also tried just pressing the "right" button to enter a sub menu but no luck. I can scroll up and down in the menu and if a song is playing I can also adjust the volume but its like i have no option to select. I downloaded the newest version of firmware by my model, I've tried formating the player but still stuck with the same problem.
Also, when in recovery mode I cant select any of the options listed in the menu.
I just bought this Device from DELL.com w/ Extended Service Protection but Im beginning to think I got a defecti've product.
If anyone could help with this frustration it'd be great
Thanks for reading.

I just contacted Dell and I'm returning for a refund. After several more attempts to try and reboot, relaod firmware to try and solve any problem with it I decided to call it quits and just chalk it up to a PoS mp3 player. I have had a 20g Samsung player for 3 years now and have had no problem with it at all. The only thing is that its not compatible with subscription services such as Napster to Go. I think I will look into a new Samsung or something else.
Good Luck

Creating template from template / editable regions

Hello all,
I'm hoping you can help me.
I am creating an online clothing shop website and am having trouble with creating category pages.
I have created the template with all headers, logos, footer, a spry menu etc.
I have then from the template (via new - Page from template etc) pages for mens / womens / shoes
This part is all fine.
However each of these pages ie. the 'mens' will have pages per category created from it for mens shirts, mens top etc.
For example I need a list of each category on the mens page that I dont want to appear on any other pages, just all of the mens category pages (tops, shorts etc) and this will also be done for the womens pages.
I saved the 'mens' page as a template but due to the section that the category list being in an 'editable region' when I have created new pages from the 'mens' template the changes wont filter through to each category page.
How can I insert a category list into the 'mens' template that will reflect the changes I make in the category pages? As I don't want to manually update each individual category page.
I hope this makes sense and someone can help me out
Thanks

What is your skill level with HTML and CSS?
I saved the 'mens' page as a template but due to the section that the category list being in an 'editable region' when I have created new pages from the 'mens' template the changes wont filter through to each category page.
This is not a good start. You do not want to begin using nested templates for anything.
One simple way (although not the optimal way) to do what you want to do is to make the place on the page where you want the lists to appear into an editable region in the template. Then create a variety of Library items (in DW) each of which contains only the list for each of your categories. On the appropriate child pages, insert the associated list into the editable region. So, for example, the men's page will have the men's list, etc.
A Library item is like a mini-template in that changes made to any given Library item are automatically propagated to all instances where that Library item is being used.
Is that what you are after?

After 7.0.2 long delay for menù showing up after restart

Good morning , after upgrading to 7.0.2 my ATV 3 restart with only family sharing and configuration menù....i think it was a fault on the fw upgrade so i reset to default configuration.
after restart everythings goes well and i restart configuring ATV but if i restart from the menù my ATV next boot again comes only family sharing and configuration...i think it was a fault in the 7.0.2 because if you also try to search for fw upgrade again i have error saying it was not possible to connect to the server...so i start thinking that after boot wireless interface is not ready...i left on ATV for about 5 minutes and magically all the menù appear...
before 7.0.2 there is no such problem...anyone experience the same ?
please let me know because i don't want to reconfigure the whole ATV to discover i need to hardware initialize again to try to solve the problem...

Assuming this is not the first time you have used your Apple TV
You might try restarting the Apple TV by removing ALL the cables for 30 seconds.
Also try restarting the router. (Also try removing it’s power cord for at least 30 seconds)
If the problem persists, try a restore, you may want to try the previous procedures several times before doing this.
If restoring from the Apple TV doesn't help, try restoring from iTunes using a USB cable.
If this is a new Apple TV, in addition to trying the above, it may also be that your network router is not allowing access to the timeserver, check that your router allows access over port 123.

Deleting unused transactions from roles

I am planning for unused transaction cleanup activity for SAP roles as mentioned below.
There are lot of roles which are copied from SAP menu due to which they consist of around 1000 transactions. Now I know there will be around 50 transactions which might be used and rest of them not used at all. I have made the strategy to find all the transactions which are not used during the last 3 months(using ST03N) and than consult the list with the role owners and delete the unused transactions.
I would like to know whether this is the correct strategy to follow, will the ST03N data-> transactional profile provides the relevant data to sort out the transactions not used in last 3 months. Please suggest or any alternative strategy can be followed. I know about sm19 audit log, but the problem is that it cannot be activated for all the users due to file space and performance issues.
Regards,
Sanjay

There are lot of roles which are copied from SAP menu due to which they consist of around 1000 transactions.
I am tempted to move this to the Test&Playground forum, because that is what building authorization roles from SAP Menü navigation nodes is.
If course if you do not care and it is better than manual profiles then it is not all bad, so I will leave it here in the security forum fir now.
From my side, if you have no clue... then go for the SAP standard roles and copy them into your own namepsace and work from there to start with. Check the objects included against audit check lists as step two. Take a closer look when you have a chance as step three (there are many manual auths in there...). You will be better off this ways than inventing roles of your own without any tcode or blue-print infos.
I would however still not call it "best practice" and it will backfire over time, but it can be done in a few days (so that you can get your bones out of the project and onto the next one without learning about the pain-points).
Eventually you become a professional bull-*******...
Cheers,
Julius

Buying Lr5.3 directly from Adobe online

I can't buy Lr5.3 directly from Adobe online in Dubai, UAE.
Anyone has similar problem?

Hi Elie,
Thanks for your response. I called up some local resellers in Dubai, UAE, there is a price difference of USD55/=. With the saving from Adobe store in US, I prefer to buy it directly online.
However, I keep getting the error message that my account was registered for another country, however i've registered for United Arab Emirates.
After many tries, the error message keeps appearing and another server error message as well.
Suddenly, the account opens up and allows me to enter my billing details. Finally purchased it from adobe mena region online via Digital River Intl.
Clicked on their link to download Lr5.3 and 4 hours later, it downloaded only 50% of it, so decided to cancel the download, it was taking way too long.
Tried what you mentioned, key in the magic password in my trial version and licensed it and it works perfectly!
Thanks, Elie

I am living in the UAE and I would like to download an install a Japanese version of Lightroom 6.

I am living in the UAE and I would like to download an install a Japanese version of Lightroom 6.
The only available version from the MENA store are English, Arabic, and French. And there is a region error when I change the region to Japan.

As I understand iTunes Gift Cards, they are for the specific country's iTunes Store where you acquired the Gift Card. To have an account in a specific country's iTunes Store the Terms of Use say that you must reside in that country, have a pernmanent billg address, not be visiting. It would be a bad idea to buy the iTunes Gift Cards. It would really complicate the authorization of the media in your iTunes library.

Need Help with iMac 350 - Won't boot - keyboard or mouse not working!

Hello,
I've scoured the web looking for answers, and can't find any, so maybe someone here would be kind enough to help. I'm working on an imac 350 blueberry for my sister and I'm having all sorts of trouble.
She bought it last week, it started up (8.6 os) no problem. Powered up and down a few times, then all of a sudden, it won't boot. I'm currently getting blinking folder/happymac/question mark when trying to start up.
Here's the big problem - the keyboard and mouse do not work now. I've tried three different mice and three keyboards and no dice with any of them. I have the 8.6 CD from her previous imac (bondi), and I can hear it spinning, but there is no way to start up from cd.
I've also tried 2 other hard drives with the same results.
Tried resetting CUDA on logic board, taking out battery, no change. Bought new battery- no change.
I would love to at least get the keyboard working to see if I can even startup from cd, anyone have any clues on how to get it working? The strange thing is that the keyboard has a power on button, and it works to start the thing up, but dies when it tries to boot. Sometimes I just get a grey screen with the pointer icon, and I can move the pointer with the mouse for a second or two, then no response.
I appreciate any help or suggestions on locating the issues!
Thank you!

When I said "but dies when it tries to boot" and "..then no response." I meant that the keyboard works to power up the computer, but won't work for anything else. So, I am figuring that the usb ports are supplying power to the keyboard and mouse, but the usb ports aren't relaying information from the keyboard or mouse.
How do you know the mouse isn't working? Won't you have to wait until later in the boot to tell?
The poweron key is a special case. I think that it works by lowering/changing the voltage on one of the usb cables. I read about this somewhere. Anyway, this function was eliminated from later usb keyboards and macs. Maybe a working power button doesn't mean what you think.
I would love to boot into open firmware
Could you try powering up from the machine? Is there a power button on the lower right of the machine?
Have you tried this key combo?
commandoption+of
The letters are in lower case. Hold all down then poweron the machine. I'd poweron from the machine as apposed to the keyboard.
You could try another usb keyboard.
We actually did boot up the computer several times with it upside down. Not for any reason, except it's become a real PIA to flip it over every two minutes to start it, then take it apart and boot again. When booting either upside down or right side up it shows the same thing - blinking folder w/finder icon and question mark.
Yes, I agree. You could try removing the clear plastic around the bottom of the machine. At least you will not have to slide in the carriage. Note. The tv portion will still be surrounded by plastic! Don't remove the plastic around the tv!
Hope I am not interfering with Richard and his comments.
Richard: Is this the orginal keyboard? When did Apple get rid of the poweron key from the keyboard? My iMac 600 didn't have the key and my iMac 233 does.
Robert
Robert

Inputting a list into an alternative to inputting it into an editable region in a template

Hello all,
I did ask this question yesterday but only got partial feedback so I'm hoping someone can help as I can't find the answer anywhere.
I'm hoping you can help me.
I am creating an online clothing shop website and am having trouble.
I have created a main template from scratch that reflects in the mens and womens pages, and the contact, about etc pages with all headers, logos, footer, a spry menu etc. I made these pages from the main template via new - Page from template etc so any changes I made to the header, logo etc will easily reflect in all of these pages.
This part is all fine.
This is my issue - in the main template I have an editable region so that I can input different content ie. 'about' info on the 'about' page, and product info on the mens / womens pages etc.
Basically in each page Mens / Womens I need category pages - tops, shirts etc. These are all in the drop down spry menu but I also want them as a list in the mens and womens pages.
From the template I created the mens and womens pages and have now saved these as a template as there will be around 10 categories for each mens and womens (tops, shirts etc) that I want to be able to replect any changes, ie. in the 'mens template' instead of having to do it in each category page - as this will take a long time.
The problem is that I put the list in the editable region in the mens template, but I now know any changes I make wont be relfected in the category pages I have made from the mens template as this is an editable region.
How can I make a category list in the mens template page that will be reflected in each category page?
I'm really stuck and have no idea how to do this, I'd appreciate any help.
Thankyou in advance

I don't recommend using multiple or nested Templates. There are much better ways to do what you want without going down this very slippery slope.
Use Server-Side Includes alone or with your main Template.
Build a Dynamic Site with databases and server-side programming.
E-commerce Solutions:
Cartweaver (extension for Dreamweaver)
http://www.cartweaver.com/
Web Assist
http://www.webassist.com/support/ecommerce-options.php
Building an e-comm site with DW & PHP (video training)
http://www.lynda.com/Web-Interactive-Web-Design-Projects-tutorials/Building-eCommerce-Web- Site-Using-Dreamweaver-PHP/83091-2.html?utm_medium=affiliate&utm_source=ldc_affiliate&utm_ content=524&utm_campaign=CD4386&bid=524&aid=CD4386&opt=
Nancy O.

Trouble with accordion panel

I'm trying to put an accordion panel in a page of the website i'm creating but i've a weird problem.
First of all, this is the link of the page
http://wwwipiniriolotermeit01.businesscatalyst.com/menù.html
As you can see, when i choose one of the option of the panel, the background begin to shake.
Of course i've tried with other panels, included muse's widget but the results is the same.
Can someone help me to resolve this issue?
Thanks in advance.

Thank you very much again.
Last time i've uncheck only the element of the master page's footer not the
entire "menu" page from the menù.
Now, as you say, the jittering is disappear.
Regards
Luca
2014-03-07 16:18 GMT+01:00 Aishvarya Raj Rastogi <[email protected]>:
Re: Trouble with accordion panel created by Aishvarya Raj Rastogi<http://forums.adobe.com/people/aishvarya+rastogi>in *Help
with using Adobe Muse CC* - View the full discussion<http://forums.adobe.com/message/6188378#6188378

Adobe Flash Media Live Encoder 3 and Dazzle 170

Hi, I have a trouble.
I'm working with: Vista Home Premium 32 Bit, Dazzle DVC 179 Rev.1.2, PCLEUSB2, Adobe Flash Media Live Encoder 3. I work with Firewire 1394 with Sony Pd100 Camcorder, and and Encoder 3 sounds well (PAL), with USB cam Encoder 3 sounds well (PAL), when I choice Dazzle from the menù, Encoder 3 tell to me: VIDEO FORMAT NOT SUPPORTED - Video format provided by video capture device is not supported by this application. (PAL or NTSC or SECAM).
What can I do for work with this device?
Thanks in advance
Vittorio

FMLE will work with all devices which have direct show based drivers and give data in raw format. Here is a list of devices which have been tested and certified with FMLE - http://www.adobe.com/support/documentation/en/flashmediaencoder/FMLE_DeviceMatrix3.0.pdf

Errors with Integrated Planning authorizations

Dear experts,
We are working with Integration Planning, and when we try to create or
modify whatever object (by the modeler or the wizard) we receive an error message like this:
"You have no authorization for Multiprovider XXXX"
Not only Multiprovider, but InfoCube....whatever object.
The curious thing is that we have with the user we are working a SAP ALL.
With the T-CODE bps0 we can do everything, but with T-CODE rsplan is
impossible.
Weve checked in the T-CODE su53 and everything is OK.
Weve checked in the T-CODE rsecadmin and nothing there.
Weve checked as well in the T-CODE st01, followed the actions with the
trace and all the return codes are 0.
Does anyone know what happens?
Thanks in advance
Cecilia

Hello Cecilia,
if you keep a carott in front of a donkey he will run faster... this is the same what I mean if I talked from experts: Men like to be the hero and instead of carott you need to need to laud him as an expert, he will reply faster
Lets come back to authorization: I am not sure whether RSECADMIN is a newer version of RSSM. Reason: In RSSM you can activate authorization check for a cube or MP but in RSECADMIN you administrate authorization for an user.
I am not sure, but I think that your problem is related to this issue. If not, there are very strange problems with the web authroization, its true: What we have done is to copy an exisiting BW user and assign him the same authorization like in web. Reason: To create a new user in the web does not work in all cases. We had very much problems with SP7, since we have SP10 we dont have those problems.
regards
Eckhard

Solaris 10 & Network [II]

Hi
I have a Solaris 10 SunFire V100 and am suffering from some very similar symptoms to the OP (which is how I found this place).
I am connecting to it from Windows PC using Hyper Terminal. Solaris boots on poweron from lom and I get the following errors:
Boot device: /pci@1f,0/ide@d/disk@2,0:a File and args:
SunOS Release 5.10 Version s10_69 64-bit
Copyright 1983-2004 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
Hostname: testboothost
Oct 28 11:44:38 svc.startd[7]: svc:/network/rpc/keyserv:default: Method "/usr/sbin/keyserv" failed with exit status 1.
Oct 28 11:44:38 svc.startd[7]: svc:/network/rpc/keyserv:default: Method "/usr/sbin/keyserv" failed with exit status 1.
Oct 28 11:44:38 svc.startd[7]: svc:/network/rpc/keyserv:default: Method "/usr/sbin/keyserv" failed with exit status 1.
[ network/rpc/keyserv:default failed (see 'svcs -x' for details) ]
testboothost console login: checking ufs filesystems
/dev/rdsk/c0t2d0s7: is logging.
I have also read the unofficial_install_x86.pdf which talks of Where is my NIC in chapter 6.1, which seems to match my problem exactly, however I cannot apply the fix, as matching the compatibility strig to etc/driver_alises isn't so easy.
Here is a snippet from prtconf -pv:
compatible: 'pci4554,434e' + 'pci128h,9102' + 'pci1282,9102' + 'pciclass,020000'
device_type: 'network'
subsystem-id: 0000434e
subsystem-vendor-id: 00004554
reg: 00006000.00000000.00000000.00000000.00000000.01006010.000000 00
.00000000.00000000.00000100.02006014.00000000.00000000.00000 000.00000100
name: 'ethernet'
devsel-speed: 00000001
class-code: 00020000
And here is a line from /etc/driver_alias that matches one of the 'compatible' strings:
dmfe "pci128h,9102"
I'm stuck - don't know where else to go. Do contact me on msn/aim/icq/email/here/whatever.
Thank you.
PS: No matter what I do, I can't stop the preview from centering all my text, sorry!

<table border="0" align="center" width="90%" cellpadding="3" cellspacing="1"><tr><td class="SmallText"><b>tcbarrett wrote on Fri, 28 October 2005 15:37</b></td></tr><tr><td class="quote">
SunOS Release 5.10 Version s10_69 64-bit
</td></tr></table>
Why are you trying to run an old obsolete pre-release version of Solaris 10?
I'd suggest that you install the final released product.

How did I get two "home folders"?

I suddenly got into problems with my backup because the home folder did not have the usual content. When I try to see what happened, it looks like I have two "home" folders.
When I select Go>Home from the men, it looks like this:
And when I click on the Data drive below the Data folder, it looks like this:
The juliusson-folder in the second image is the one that I thought was the home folder. It contains the stuff that I want to back up.
Can someone see from this what could be wrong? I don't really know how it should look.
When this happened, I also lost my user settings.

julle300 wrote:
I don't know if I moved the Home folder out of the start up drive on purpose It could have been part of my original configuration.
I set up my computer years ago by following some online instructions for an optimised set up for Photoshop work. I have three drives installed. One 1TB drive and two 2TB drives. The instructions that I followed were meant to put the system and programs on one drive (also used as scratch drive) and then have images and other stuff on the other two. Those two were set up as a mirrored RAID configuration.
Everything has worked fine for over three of years. Could the problems be caused by an accidental folder move?
It's hard to understand how an accidental folder move would cause this - the home folder path is also set within the system configuration. That means you can't just use any old folder as the home folder location.
I guess it's possible an accident moved it, but then there would have been some user interaction to have agreed to use it in the new location. It seems likely that you somehow managed to use the OS when the Data disk was offline - the folder got created in place of the old home folder, that caused a new one to be made (new home folders get the default template with Desktop, Documents, Music, Pictures etc).
Have you got another user account on the system? Is that user an admin? Does that user work OK?
You will need an admin account to fix this issue, please create one & leave the home folder for the admin on the main boot disk.
Do you have any data that you need within the current home folder (the new one inside the Data folder)?
Your original settings will be saved in the original home folder, but that is not being used at present. If you can abandon the new home folder here is what I suggest…
Disable automatic login if it is enabled - you need to stop logging in as 'juliusson' whilst you fix this, it can be re-enabled when it is fixed.
Create a new admin user account in 'System Preferences > User & groups', this is as a backup to allow you to manage the computer whilst fixing the home folder.
Reboot, login as the new admin account.
In 'System Preferences > User & groups', unlock the panel with the admin password (click the padlock)
Select the 'juliusson' user account, right click (or ctrl+click) the name & select 'Advanced Options…' in the popup.
Look at the 'Home Directory:' path. That needs to be set to the old location. By default that should be /Users/juliusson, yours looks like it should be /Volumes/Data/juliussonIf you are unsure use the Finders 'Go menu > Go to Folder…' to open '/Volumes/Data/juliusson' confirm that it contains some of your old user files.*
Save the correct path in the 'Home Directory' setting & reboot (do not edit any other Advanced fields)
*NOTE: In steps 6 you probably will not see the correct path since the Data folder is occupying the same location that the Data disk uses. To get around this you will need to rename the Data folder insider /Volumes, and reboot. I'd suggest you move the user home inside the Data folder to a new location as a backup & then delete the entire Data folder in /Volumes/. A reboot will be required to allow the Data disk to mount into the /Volumes/Data location. Once it mounts correctly login should work.
You can merge the home folders as Barney suggested, but this is probably safest via a manual approach unless you are willing to spend time & are experienced in comparing files with apps the can do selective copying (ChronoSync for example).
Please ask if you are unsure about any of this - it's major changes to your user data setup - a full backup is essential before beginning. Setting the home path is the correct way to relocate a home folder once the data is moved.

Classes and Static

1. i have Class a, this has static main
2. i have Class Conn, this connects the DB
3. i have Class Men, has Methods
4. i Create in Class Conn a Vector from Class Men.
5. main is static. i call Conn in main.
6. java doesnt allow me to call Conn from main if Conn methods are not Static.
7. ok i made Conn methods static.
8. now: if i want to call the Vector of Men Class in Conn Class. i cant. i have to make Men Class also Static.
9. well greate java. everything must get Static!!!! hmm.
whats the solution?
thx

I agree that you are probably best helped by reading an introduction to Java programming.
The "main" thing in this case is that you shouldn't try to do everything directly from your main method. In your class a (which should by convention be called A, or better yet, something a little more descriptive), you have a main method that is used to start your application. This method should look something like this:public static void main(String[] args) {
A myApplication = new A();
a.performDuties(); // this is a method you have to create
}That's it, no more. The method performDuties() (which is NOT static) will do all the work.

Poweron from sc men�

Similar Messages

Maybe you are looking for