Powersave mode does not work

Hi,
This is my first post.  I have a new HP Laserjet CP2025dn.  The printer is connected to a home network via an ethernet cable (the printer has a built-in connector for this).  It is not connected wireless.
The powersave mode kicks in intermittently.  The printer should go into powersave 15 minutes after it's been idle, as long as I do not print to it or touch the control panel.  But when it goes into powersave mode, it comes out of it by itself into the "ready" mode, without any print job having been sent to it or anyone physically touching the printer.  It later goes into powersave mode, but the time it takes to do this varies.  I have tried installing the latest firmware but it makes no difference.
Now if I disconnect the network cable, it works properly, that is that it will go into powersave by itself and stay there (since I cannot send any print jobs to it with the cable disconnected).  So I must assume that some network activity is causing the printer to come out of powersave mode, but I would assume the printer is designed to do this only when a print job is sent to it, regardless of any network traffic or PCs on the network turning on or off.
Is this printer behaving as it should?  If not, is there a solution?  HP tech support seems at a loss to fix this.
Thanks.

hello its not firmware  9.42 causing....
Powersaver - Automaticaly KeyPad will Off by seconds
Sleepmode - it will be Stand by ---> you see its normal to see your wallpaper/screensaver when the screen light was off but in your screen its Stand by and nothing else ....
 Also Tip...
Try to on your Automatic Keypad Lock Standby its a Combination of SLEEPMODE of your Phone
You can set the timer of Keypad
 menu-->Setting-->Phone-->Automatic keyguard
and try to update your firmware ver9.42 into new ver10.10
i change my firmware 9.42 into 10.10 it will be fix your fullscreen als.
Message Edited by neverwinter on 08-Jun-2009 11:37 AM
Message Edited by neverwinter on 08-Jun-2009 11:38 AM
My Phones
Nokia 3210,3310,8250,2610
Nokia (ExpressMusic) 3250,5310
Nokia (Nseries) N70 N73
[IMG]http://i121.photobucket.com/albums/o220/holodeck3/untitled-3.jpg[/IMG]

Similar Messages

  • I have a mac which plays the boot sound but the screen stays black. Recovery mode does not work, as the keyboard is wireless. What do I do?

    What it says in the title.
    I have an older mac and it worked perfectly until about an hour ago when I shut it down because we needed the room dark for a presentation and the screen saver was putting out light.
    Now it won't turn back on. It plays the start up music but the screen stays blank.
    The CMD+OPT+R for recovery mode doesn't do anything, the keyboard is wireless so the command doesn't get to the computer and that's the only keyboard I have since that's the one it came with.
    I'm looking at making a USB recovery disk but it says that I should click on "Options" in the Disk Utility but there is no options button or menu to click.
    From here: OS X: About Recovery Disk Assistant in step 3 I get stuck.
    Also it says that if I make a drive on this computer which has an older OS it might not work on the broken machine with Mavericks.
    This machine literally worked and I turned it off and now it does not work and there seems to be nothing I can do... ***...

    kodemage wrote:
    well, then recovery mode does not work. I've tried all the key combinations I've seen on line. Command+R, Command+Option+R, Command+Option+P+R, none of these work.
    I don't believe there is anything we can do on a forum to help then, you need to take it into a AASP and have it professionaly diagnosed. If you don't know how to locate an AASP in your area you can begin by using Contact Apple for support and service
    Good luck.

  • Clamshell mode does not work with Mountain Lion.

    Installed Mountain Lion on 11" MacBook Air last Friday night.  Now system does not appear to work in Clamshell mode, as it won't wake or connect to external monitor.

    Apple Tech Support was very helpful.  The MBA works in clamshell mode next to my monitor now -- but does not work in the Henge Dock.  Henge Dock has been contacted.

  • Digital ICE epson scan (professional mode) does not work

    Hello,
    I am running the latest Mountian  Lion OS on my IMAC and have recently started running some test scans with  my Epson Perfection V700 scanner. The supplied Epson software , Epson Scan offers a variety of operating modes, "professional mode" offering the most features. Professional mode offers Digital ICE as an option, however when selected, the Digital ICE does not work.I have compared scans with  and without digital ICE and they are exactly the same. Scratches and dirt are not removed by the scan.
    If I select a more basic mode ("Home Mode") Digital ICE does  work. But this other mode does not offer the range of options offered in porfessional mode.
    Has anyone out there used Epson Scan software?  Has anyone else experienced this problem? Is there other scanning software out there which could fully exploit the features of the Epson scanner I have?  I tried Vuescn and it does not seem to be compatible with my scanner, so that is off the table.
    Dean

    You should first read the user manual that came w/your scanner and/or contact Epson tech support.
    How is the scanner connected to your iMac?  USB cable?  Wireless?  Firewire?
    Has anyone out there used Epson Scan software?
    I have an Epson scanner.  It only work when it's connected directly to my iMac via USB cable.
    Has anyone else experienced this problem?
    Initially.
    Is there other scanning software out there which could fully exploit the features of the Epson scanner I have?
    http://support.apple.com/kb/PH11070 OS X Mountain Lion: Troubleshoot a network printer 
    http://support.apple.com/kb/PH11143 OS X Mountain Lion: Reset the printing system
    http://support.apple.com/kb/HT3669 Printer and scanner software available for download
    What to do when you can't print/scan
    Sometimes, installing the GIMP drivers help with printing/scanning issues: http://gimp-print.sourceforge.net/MacOSX.php

  • Antares autotune 4 graphic mode does not work in Logic

    Has anyone found a workaround for the following issue:
    Using Antares autotune 4 or 5 in Logic pro 8, I cannot use the graphical mode how it was intended. Using Cubase, I was able to launch the plugin, switch to graphic mode, and track the pitch vs time. This was useful to manually correct the pitch for each syllable. For some reason, this function does not work in Logic Pro 8. Any thoughts as to why? Am I doing something wrong? Please advise.

    I haven't used AT in years, but I do still have AT 4.
    Graphic mode works just fine here in Logic 8, and I'm still on Tiger as well, albeit 10.4.11
    Not that you asked, but seriously, look into Melodyne. AT is so archaic as far as it's graphic mode is concerned. 30 seconds back with it and I can't seriously see why anyone would use that plug-in, other than maybe manual mode, for a quick "run a comb through it" fix.
    Sorry I couldn't give you an answer as to why this is happening. have you contacted Antares?

  • In printing a document my preview mode does not work??

    in printing a mail recieved message my preview mode sends a message stating Preview is not supported???

    I have paid the full extended version, but it is not working. See my screenshots.

  • EA6700 bridge mode does not work - error 2218

    I've just bought WiFi router EA6700-EE and now trying to configure it.
    After connecting to Internet I upgraded its firmware to the latest version.
    I want it to be just a bridge but when I select this option and press OK I get a message (translated from Russian):
    "Unexpected error 2218
    An unexpected error occurred. If this problem persists, please visit our web site technical support.
    Details
    /jnap/ui/SetRemoteSetting"
    Is it possible to fix it?

    What Hardware version is your router?
    What Firmware version is currently loaded?
    What region are you located?
    Was a Factory Reset performed before and after any firmware updates then set up from scratch?
    I recommend doing the following: Download the FW file from the support site first.
    Disable the auto update feature on the router.
    1. Save router config to file first using IE or FF with all security add-ons disabled.
    2. Factory reset the router with all other devices disconnected or turned OFF accept for 1 wired PC.
    http://kb.linksys.com/Linksys/ukp.aspx?pid=80&app=vw&vw=1&login=1&json=1&docid=9d2ff02077f645679972a...
    3. Reload or Update the FW using IE or FF. Just download the FW file to your local wired LAN PC.
    http://kb.linksys.com/Linksys/ukp.aspx?pid=80&app=vw&vw=1&login=1&json=1&docid=0a6881b90224439b92c8d...
    4. Factory reset the router and then set up from scratch first using the local log in link and test with out loading the saved config from file. Check to see if any problems are fixed before loading the saved config from file. Sometimes you need to set up from scratch with out loading the saved config file. Just safer that way.
    PC Web Browser Configurations
    What browser are you using?
    Try Opera or FF? If IE 8, 9, 10 or 11, set compatibility mode and test again.
    Disable any security browser Add-ons like No Script and Ad-Block or configure them to allow All Pages when connected to the router.
    Clear all browser caches.
    Be sure to log into the Admin account on the router.
    Try this as a test and see if cascading method works:
    http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=169333b784cf4c78b8db5490f85c518a_Setting_.xml&pid=...
    morales2k wrote:
    I am also having this issue (with the exact same error details), the ip is indeed ipv4.
    My current setup is that this router is connected to another router. 
    The router giving out the error was previously set up to use automatic dhcp, but then it had dhcp disabled on another screen, instead of setting it up in bridge mode in the first place. 
    I went in and tried to set it up in bridge mode, but then it gave out this error.

  • Ever since updating my LG G2 to VS98026A the Quiet mode does not work properly and is not controllable.

    My LG G2 started to have problems since the latest system update.  Previously, the phone worked perfectly! 
    I now cannot control the Quiet mode settings and the vibrate and silent modes are no longer selectable.  This is not acceptable.  I have no way of silencing the phone if I need to.
    Is there a way to return the phone to the previous state?

    http://www.verizonwireless.com/support/knowledge-base-87344/
    No can't go back but if you reset you g2 make sure you use cloud storage ahead of time on WiFi to backup data or connect to a computer and know your Google account. If on more everything plan you can use the free 25gb of vcloud storage

  • My iphone 4 is disabled for 22 million minutes and the recovery mode does not work? How can I fix this?

    I have tried to do the standard recovery mode where you hold down the home button and plug in the USB but Itunes is not recoginizing the phone. How can I fix this issue?

    Hello there, Itraziel.
    Thanks for providing further clarification on your issue. The following Knowledge Base articles offer up some assistance depending on which Operating System your computer is running:
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/ts1538
    or
    iOS: Device not recognized in iTunes for Mac OS X
    http://support.apple.com/kb/ts1591
    If you are still unable to restore the iPhone, this article may provide some more information:
    If you can't update or restore your iOS device
    http://support.apple.com/kb/ht1808
    Use recovery mode
    Recovery mode erases your device and restores it, which should resolve the issue. If you previously synced with iTunes or iCloud, you may be able to restore from your backup after recovery.
    Turn off your device. If you can't turn it off, press and hold the Sleep/Wake and Home buttons at the same time and wait a few seconds for it to turn off.
    Plug the device's USB cable into your computer only.
    Hold down the device's Home button as you connect the USB cable to it.
    When you see the Connect to iTunes screen, release the Home button. If you don't see this screen, try steps 1 through 3 one more time.
    iTunes should open and display a message such as: "iTunes has detected an iPhone in recovery mode. You must restore this iPhone before it can be used with iTunes."
    Use iTunes to restore your device.
    Thanks again for reaching out to Apple Support Communities.
    -Pedro

  • Firefox crashes on startup and safe mode does not work. This is not the first time this has occurred and I usually have to reinstall to correct it.

    Crash id:bp-c139f06f-3d8e-4ff9-8614-323b52130920

    Certain Firefox problems can be solved by performing a ''Clean reinstall''. This means you remove Firefox program files and then reinstall Firefox. Please follow these steps:
    '''Note:''' You might want to print these steps or view them in another browser.
    #Download the latest Desktop version of Firefox from http://www.mozilla.org and save the setup file to your computer.
    #After the download finishes, close all Firefox windows (click Exit from the Firefox or File menu).
    #Delete the Firefox installation folder, which is located in one of these locations, by default:
    #*'''Windows:'''
    #**C:\Program Files\Mozilla Firefox
    #**C:\Program Files (x86)\Mozilla Firefox
    #*'''Mac:''' Delete Firefox from the Applications folder.
    #*'''Linux:''' If you installed Firefox with the distro-based package manager, you should use the same way to uninstall it - see [[Installing Firefox on Linux]]. If you downloaded and installed the binary package from the [http://www.mozilla.org/firefox#desktop Firefox download page], simply remove the folder ''firefox'' in your home directory.
    #Now, go ahead and reinstall Firefox:
    ##Double-click the downloaded installation file and go through the steps of the installation wizard.
    ##Once the wizard is finished, choose to directly open Firefox after clicking the Finish button.
    Please report back soon.

  • Firefox immediately crashes at launch; Safe Mode does not work

    Firefox automatically crashes upon launch, and takes me to the Crash Reporter tool.
    I have attempted to reinstall both the application itself, as well as deleting any/all preferences and cache files I could locate within my Home folder's Library folder—however, nothing has worked so far.

    With which Firefox version do you have that problem?
    Your system details list show a Firefox 3.6.24 version, but your user agent shows a TenFourFox signature.
    See:
    *http://kb.mozillazine.org/Firefox_crashes
    *https://support.mozilla.org/kb/Firefox+crashes

  • Sleep Mode in Windows 10 Does not work

    Ever since I upgraded to Windows 10 Sleep mode does not work properly when closing the lid or pressing the shutdown button when you set these to sleep.  I have updated the BIOS, Intel Chip Set Drivers, and Video Driver to the latest.  All HP and Windows UPdates installed. Problem is not everthing goes to sleep, typically my ethernet connection, audio and fan stay on.  Must use the Power Button and Hold to recover.  Each time I close the lid and open it I have a black screen.  I can tell when it is not going to sleep by noticing the Ethernet jack is still lit and the fan making noise after closing the lid or pressing the power button. Here's the kicker, make a change to any of the power settings, save and come back into them and reset to sleep and it will work with the lid ONE TIME ONLY.   There after its back to never working, never fully sleeping and having to reboot. Need Help.

    I just discovered that HP has posted a new support page for people who are having issues with the computers after converting to Win 10. I was particularly interested in the section on issues with Sleep/Hibernation and found this whole page: http://support.hp.com/us-en/document/c03383935 Looks like apart from the driver issue, it could be that the settings in the Device Manager for your KEYBOARD are not set correctly!!! - yeah, that's what I said.  Anyway, the full resource is located here and may be of some help. http://support.hp.com/us-en/document/c04773236/ PS: I also checked to see if there were new drivers for my notebooks and see that it has now been two days since they were last updated. Perhaps there is hope!

  • My MacPro 1,1 will only boot if I resert PRAM each time, and then that does not work each time. When it does boot all is fine. Any idea before I head off to genius bar.

    To boot my MacPro now, I have to go thru the reset Pram. Doesn't work each time. I usually don't turn my machine off. Booting in Safe mode does not work...when it doesn't boot I get only a gray screen, no icons in the screen like bad disk etc. I have replaced the battery. My professor son tells me to setup a new drive internally and install a new system and see if the new OS works. I have 3 internal drives with all data on bays 3 and 4... Bay 1 is the system drive with apps only. I'm 70 miles from the closest Apple store and thought I would ask tonight before driving in.

    Replacing the PRAM ("backup") battery on the machine may be needed.  Here's how, go to page 50 of the user manual:
    http://manuals.info.apple.com/en_US/Mac_Pro_User_Guide.pdf

  • ITunes organizing music does not work and deletes my files

    When I have checked box nex to where it said something like : keed folder organized, scince i have so much music, it decided to move my music into compilations folder it had created by itself. After wards i was moving files from compilations folder to artist music belonged to. Little while later it decided to move all my music to the trash. And scince trash doesn't hold everything, it deleted 95% of my music. iTunes decides also to create and decide where to put music by itself, moves half to under artist name half somewhere else. Just to let apple people know, next time I'll get an mp3 player, but rather go with Zune or something, so I wouldn't have to use iTunes

    Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
    iOS: Wrong passcode results in red disabled screen                          
    If recovery mode does not work try DFU mode.                         
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings         
    For how to restore:
    iTunes: Restoring iOS software
    To restore from backup see:
    iOS: How to back up      
    If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
    You can redownload iTunes purchases by:
    Downloading past purchases from the App Store, iBookstore, and iTunes Store         

  • CRVS2010 Beta - Printing does not work in Google Chrome

    I 've run into an issue with printing crystal reports using Google Chrome. I've tested this on 4 different computers with the same result. When a user clicks print the printer dialog does not appear and the report will not print.
    The version of Google Chrome tested is 6.0.472.63

    ActiveX print works on IE. But I had to do a bunch of ActiveX and security configurations in IE (Using Server 2008) - allow ActiveX download, etc., etc.
    PDF print mode does not work on my computer either. However I have the same build on this box as the public download. The latest internal build does print and export to pdf with no issues. So, I suspect this was a bug, but it is now resolved and should be OK at RTM.
    Ludek

Maybe you are looking for