PPPoE Cisco 7206VXR + NPE-400

Hi ,
i am wondering if 7206VXR + npe400 is good enough for terminating (as BRAS) 2000 pppoe sessions over ethernet.
What is max number of pppoe sessions on such hardware ?
Is it possible to make traffic shaping for each separate pppoe session ?

Hi,
Here is the link for the PPPOE session limit, which might be helpful:
http://www.cisco.com/en/US/docs/ios/12_2t/12_2t13/feature/guide/ftppp.html#wp1024557

Similar Messages

Cisco 7206VXR (NPE-G2) Error - %SW_MGR-3-CM_ERROR_FEATURE_CLASS: Connection Manager Feature Error: Class SSS: (QoS) - install error, ignore.

Dear Cisco Expert,
We are facing problem terminating PPPoE users on Cisco 7206VXR NPE-G2 router where in user connects to router but policy-map is not applying on user interface.
Below mentioned message is logged on router.
%SW_MGR-3-CM_ERROR_FEATURE_CLASS: Connection Manager Feature Error: Class SSS: (QoS) - install error, ignore.
Below is the "show version" output.
Cisco IOS Software, 7200 Software (C7200P-ADVIPSERVICESK9-M), Version 12.2(33)SRC, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Fri 11-Jan-08 02:44 by prod_rel_team
ROM: System Bootstrap, Version 12.4(12.2r)T, RELEASE SOFTWARE (fc1)
aggr03 uptime is 1 day, 6 hours, 4 minutes
System returned to ROM by reload at 05:45:18 IST Wed Sep 3 2014
System restarted at 05:46:53 IST Wed Sep 3 2014
System image file is "disk2:c7200p-advipservicesk9-mz.122-33.SRC.bin"
Last reload reason: Reload command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco 7206VXR (NPE-G2) processor (revision A) with 1966080K/65536K bytes of memory.
Processor board ID 31782123
MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.2
6 slot VXR midplane, Version 2.7
Last reset from power-on
PCI bus mb1 (Slots 1, 3 and 5) has a capacity of 600 bandwidth points.
Current configuration on bus mb1 has a total of 0 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
PCI bus mb2 (Slots 2, 4 and 6) has a capacity of 600 bandwidth points.
Current configuration on bus mb2 has a total of 0 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
Please refer to the following document "Cisco 7200 Series Port Adaptor
Hardware Configuration Guidelines" on Cisco.com <http://www.cisco.com>
for c7200 bandwidth points oversubscription and usage guidelines.
1 FastEthernet interface
3 Gigabit Ethernet interfaces
2045K bytes of NVRAM.
500472K bytes of ATA PCMCIA card at slot 2 (Sector size 512 bytes).
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
Can somebody help please?
Thanks,
Nilesh.

Hi Inayath,
We are applying policy-map on user virtual-interface via radius attributes.
Cisco-Avpair+="lcp:interface-config#1=service-policy input 256k"
Cisco-Avpair+="lcp:interface-config#2=service-policy output 256k"
Below is the relevant configuration for cisco router.
aggri03#sh policy-map 256k
Policy Map 256k
    Class 256k
     police cir 520000 bc 32000
       conform-action transmit
       exceed-action drop
aggri03#sh run int virtual-te1
Building configuration...
Current configuration : 398 bytes
interface Virtual-Template1
mtu 1492
ip unnumbered Loopback100
no ip redirects
no ip unreachables
no ip proxy-arp
no logging event link-status
peer default ip address pool poolname
no snmp trap link-status
keepalive 60
ppp authentication pap callin
ppp ipcp dns 203.187.x.y 203.187.x.y
ppp timeout ncp 30
ppp timeout authentication 20
ppp timeout idle 480
end
Below is the complete log line on router.
Sep 3 16:41:31: %SW_MGR-3-CM_ERROR_FEATURE_CLASS: Connection Manager Feature Error: Class SSS: (QoS) - install error, ignore.
-Traceback= 4A9C88 4AAC20 4AB350 12B6040 12C8B38 2C2F24C 2C2F2FC 12C8E0C 12C9000 12C94D0 12B4788 12B4D40 12B4E84 12AFEB0 12B02FC
Please let me know if you want further information & thanks for your inputs.
Thanks,
Nilesh.

Cisco 7206VXR (NPE-G2)

Hi
Need to upgrade IOS for Cisco 7206VXR (NPE-G2) please suggest me the stable image and also please let me know if need to upgrade boot helper as well.
TRV-777-MPLS-RT1#show bootflash:
-#- ED ----type---- --crc--- -seek-- nlen -length- ---------date/time--------- name
1 .. image EDD729F8 955DD4 29 9264468 Jan 18 2000 16:50:10 -05:00 c7200p-kboot-mz.124-15.T7.bin
2 .. crashinfo 77E206C7 98E518 25 231105 Apr 21 2013 18:16:03 -04:00 crashinfo_20130421-221603
56040168 bytes available (9495832 bytes used)
TRV-777-MPLS-RT1#dir
Directory of disk2:/
1 -rw- 31915084 Jan 18 2000 16:59:46 -05:00 c7200p-advsecurityk9-mz.124-15.T7.bin
2 -rw- 6389760 Feb 6 2009 09:55:48 -05:00 sdm.tar
3 -rw- 1505280 Feb 6 2009 09:56:00 -05:00 common.tar
4 -rw- 1038 Feb 6 2009 09:56:06 -05:00 home.shtml
5 -rw- 112640 Feb 6 2009 09:56:12 -05:00 home.tar
6 -rw- 527849 Feb 6 2009 09:56:18 -05:00 128MB.sdf
7 -rw- 793739 Feb 6 2009 09:56:26 -05:00 256MB.sdf
8 -rw- 1697952 Feb 6 2009 09:56:38 -05:00 securedesktop-ios-3.1.1.45-k9.pkg
9 -rw- 415956 Feb 6 2009 09:56:46 -05:00 sslclient-win-1.1.4.176.pkg

Hello
its not very clear why you want to upgrade and what features you need to support. You seem to be running T train image which generally has a number of new features., and I believe 12.4 is now rather old. Perhaps you should look at 15.2 and check feature navigator and release notes to see if it has all the features you need.
i believe it is good practise to use the correct boot image too to match your chosen ios.
hope this helps
mark

Bandwidth point on Cisco 7206VXR (NPE-G2)

After greeting...
PCI bus mb1 (Slots 1, 3 and 5) has a capacity of 600 bandwidth points.
Current configuration on bus mb1 has a total of 0 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
PCI bus mb2 (Slots 2, 4 and 6) has a capacity of 600 bandwidth points.
Current configuration on bus mb2 has a total of 800 bandwidth points.
is there any effect on router when bandwidth points exceeded it's point like i marked above???if there is please point it to me...

Hello Sami,
Trust you are doing great.
When installing cards into a 7200, there are clear guidelines as to the order in which slots should be used, in order to maximize the available backplane bandwidth. The bandwidth is divided between two pci buses that are used to connect left and right hand cards. The available bandwidth is split between the left and right slots on the chassis. Cisco uses a system of bandwidth points, whereby the different types of interface cards have a bandwidth points value. For instance a PA-A3-OC3 card has a value of 300 points. On a 7206VXR router, the total bandwidth points for the either the left or right-hand side slots must not total more than 600 points. The bandwidth points should be evenly distributed between the left and right slots
Now from the logs which you have shared, it seems that you have installed Port Adapters on left half whose Bandwidth point sum is exceeding the 600 Bandwidth Point limit for the left side.
Effect of this: The effect would be that the Port Adapters you have used in Left side may be working in "Half Bandwidth Point".
This would allow to use only one interface out of two in the Port Adapters.
When there is any oversubscription, below message is also displayed in "show version"
The set of PA-2FE, PA-POS-2OC3, and I/O-2FE qualify for "half
bandwidth points" consideration, when full bandwidth point counting
results in oversubscription, under the condition that only one of the
two ports is used. With this adjustment, current configuration on bus
mb1 has a total of 600 bandwidth points
Please let me know if there is any concerns about these.
Regards,
Mohit
**Please rate if you find this helpfull

Does 7206VXR (NPE-G2) with c7200p-advipservicesk9-mz.150-1.M7 supports DMVPN phase 3?

Hello,
We have a cisco 7206VXR (NPE-G2) with IOS c7200p-advipservicesk9-mz.150-1.M7.bin.
We want to implement DMVPN phase 3 but the command "show ip nhrp shortcut" is not included.
does 7206VXR (NPE-G2) with c7200p-advipservicesk9-mz.150-1.M7 supports DMVPN phase 3?
Is there any other command to verify the DMVPN phase 3 implementation?
Thank you in advance!

Hi Inayath,
We are applying policy-map on user virtual-interface via radius attributes.
Cisco-Avpair+="lcp:interface-config#1=service-policy input 256k"
Cisco-Avpair+="lcp:interface-config#2=service-policy output 256k"
Below is the relevant configuration for cisco router.
aggri03#sh policy-map 256k
Policy Map 256k
    Class 256k
     police cir 520000 bc 32000
       conform-action transmit
       exceed-action drop
aggri03#sh run int virtual-te1
Building configuration...
Current configuration : 398 bytes
interface Virtual-Template1
mtu 1492
ip unnumbered Loopback100
no ip redirects
no ip unreachables
no ip proxy-arp
no logging event link-status
peer default ip address pool poolname
no snmp trap link-status
keepalive 60
ppp authentication pap callin
ppp ipcp dns 203.187.x.y 203.187.x.y
ppp timeout ncp 30
ppp timeout authentication 20
ppp timeout idle 480
end
Below is the complete log line on router.
Sep 3 16:41:31: %SW_MGR-3-CM_ERROR_FEATURE_CLASS: Connection Manager Feature Error: Class SSS: (QoS) - install error, ignore.
-Traceback= 4A9C88 4AAC20 4AB350 12B6040 12C8B38 2C2F24C 2C2F2FC 12C8E0C 12C9000 12C94D0 12B4788 12B4D40 12B4E84 12AFEB0 12B02FC
Please let me know if you want further information & thanks for your inputs.
Thanks,
Nilesh.

Cisco 7206vxr randomly rebooting

I have a cisco 7206vxr router that has been randomly rebooting.
This is the error I am getting.
System was restarted by bus error at PC 0x623F6FD0, address 0xB0D0B0D at 10:48:15 CST Fri Dec 17 2010
Reading through some stuff on the cisco site I see that the address shown is not a vaild memory location. Do any of you guys have any ideas?

CVFTC_7206#sh ver
Cisco IOS Software, 7200 Software (C7200-IS-M), Version 12.4(3), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Fri 22-Jul-05 09:13 by hqluong
ROM: System Bootstrap, Version 12.2(8r)B, RELEASE SOFTWARE (fc1)
BOOTLDR: 7200 Software (C7200-KBOOT-M), Version 12.2(15)B, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
CVFTC_7206 uptime is 2 days, 15 hours, 40 minutes
System returned to ROM by bus error at PC 0x623F6FD0, address 0xB0D0B0D at 16:28:24 CST Fri Dec 17 2010
System restarted at 16:31:04 CST Fri Dec 17 2010
System image file is "disk2:c7200-is-mz.124-3.bin"
Cisco 7206VXR (NPE-G1) processor (revision A) with 491520K/32768K bytes of memory.
Processor board ID 20402731
SB-1 CPU at 700MHz, Implementation 1025, Rev 0.2, 512KB L2 Cache
6 slot VXR midplane, Version 2.0
Last reset from power-on
PCI bus mb1 (Slots 1, 3 and 5) has a capacity of 600 bandwidth points.
Current configuration on bus mb1 has a total of 0 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
PCI bus mb2 (Slots 2, 4 and 6) has a capacity of 600 bandwidth points.
Current configuration on bus mb2 has a total of 0 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
Please refer to the following document "Cisco 7200 Series Port
Adaptor Hardware Configuration Guidelines" on CCO ,
for c7200 bandwidth points oversubscription/usage guidelines.
3 Gigabit Ethernet interfaces
509K bytes of NVRAM.
62720K bytes of ATA PCMCIA card at slot 2 (Sector size 512 bytes).
16384K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x2102

Nice People HELP ME!!! IPv6 over PPPoE Configuration on Cisco 7206VXR

I have a 7206VXR which connects to a DSLAM via the router's ATM/DS3 interface. A CPE home router connects to the DSLAM. So it's like:
PC -----ethernet---- CPE Router ------ dsl line ------ DSLAM ----- atm/pppoe ------- BVI/Virtual-Template/PPPoE on Cisco 7206VXR
Now the problem is:
- PC CAN ping the BVI interface of Cisco, but NOT beyond that. For instance he can't ping 7206's loopback ipv6 address.
- I found something interesting on the CPE, that CPE itself can't ping BVI interface of Cisco, AND it doesn't have a default gateway ::/0 set on itself. I manually added a default router like "route -A inet6 add ::/0 gw <BVI's IPv6 addr>", and the problem got solved and PC can ping Cisco's loop back IP now. But this is not a solution since I want this thing to be automatically ready.
Note both CPE and PC are happy with global IPv6 addressed assigned.
I believe this problem is related to how PPPoE/IPCPv6 handles addresses and prefixes.
Ok, now some configuration details: I use 2001:7:7::/64 for the "WAN" side of CPE, and 2001:8:8::/64 for its LAN side (PCs). And here's the Cisco config (only related stuff is shown here):
ipv6 unicast-routing
ipv6 cef
ipv6 dhcp pool foo
prefix-delegation pool test
address prefix 2001:7:7::/64
bridge irb
bba-group pppoe global
virtual-template 2
sessions max limit 256
interface Loopback0
no ip address
ipv6 address 2001:9:9::1/64
ipv6 enable
interface Virtual-Template2
description Public PPP CHAP
mtu 1492
ip unnumbered BVI1
ip pim sparse-dense-mode
ip igmp version 3
ipv6 unnumbered BVI1
ipv6 enable
ipv6 mtu 1492
ipv6 nd managed-config-flag
ipv6 nd other-config-flag
ipv6 nd router-preference High
no ipv6 nd ra suppress
ipv6 dhcp server foo
peer default ip address dhcp-pool Public
peer default ipv6 pool test
ppp authentication chap
ppp pap refuse
interface BVI1
description Public IP ADSL
ip address 12.230.197.129 255.255.255.224
ip pim sparse-dense-mode
ip igmp version 3
ipv6 address 2001:7:7::1/64
ipv6 enable
ipv6 mtu 1492
ipv6 nd managed-config-flag
ipv6 nd other-config-flag
ipv6 nd router-preference High
no ipv6 nd ra suppress
ipv6 nd ra lifetime 60
ipv6 nd ra interval 40
ipv6 local pool test 2001:8:8::/56 64
NICE PEOPLE PLS HELP ME! ^_^

Thanks Andrew for your response and sorry for the confusion: actually I didn't include all my config lines. For bridging, actually I did what you mentioned and everything works fine with IPv4:
interface ATM1/0.3 multipoint
description Public DHCP
bridge-group 1
pvc 1/1060
encapsulation aal5snap
bridge 1 protocol ieee
bridge 1 route ip
bridge 2 protocol ieee
bridge 2 route ip

"IPSECcard: an error coming back 0x007F" error on Cisco 7206vxr router having SA-VAM2+

Hi,
I am getting "IPSECcard: an error coming back 0x007F" error on Cisco 7206vxr router having SA-VAM2+ having IOS c7200-jk9s-mz.124-19.bin & NPE-G1
The Configuration is like below
crypto isakmp policy 1
encr 3des
hash md5
authentication pre-share
group 2
lifetime 28800
crypto ipsec transform-set kotakbank esp-3des esp-md5-hmac
crypto ipsec df-bit clear
Impact: After getting this error, the VPN tunnels are impacted.
Can any one tell us the solution ?.
Thanks...Pramod.

Upon replacing SA-VAM2+ issue got resolved... Thanks..

DMVPN on a 7206 with NPE-400

Has anyone deployed or tested the capabilities of DMVPN on a 7206 platform with a NPE-400?
I have two spare 7206 routers that were pulled from production and have NPE-400 cards, and NO vpn acceleration modules available. I would like to use these for DMVPN hub routers but can't seem to find any good documentation on the scalability of the NPE-400 and mGRE/IPsec.
Thanks!

Following links may help you
http://www.cisco.com/en/US/prod/collateral/iosswrel/ps6537/ps6586/ps6660/prod_white_paper0900aecd803498b1_ps6658_Products_White_Paper.html
http://www.cisco.com/en/US/products/hw/routers/ps341/prod_brochure09186a0080092130.html

QoS on Cisco 7206VXR DMVPN

Hello,
one of my customers wants to implement VoIP in his existing DMVPN Network Topology. I have read about the "Per-Tunnel QoS for DMVPN" but when it comes to configure it on my hub router (Cisco 7206VXR with c7200p-advsecurityk9-mz.124-15.T14.bin) I am lacking the option to set the "ip nhrp map group" command.
My question now is, is it generally not supported by the 7206VXR platform? Or can I get the option by upgrading the IOS to a newer version? If so, which one could I use ?
Kind regards
Thomas

Hello Victor,
thanks for your answer, I did not know, such an tool exists. very helpfull.
For those who might be interessted, here is the link: http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp
Thanks again.
Greetings, Thomas

7206VXR NPE-G2 IOS 15.1(3)2 netflow problem

Hello,
I am trying to configure netflow on 7206VXR NPE-G2 and IOS 15.1(3)2. Put ip flow ingress on interfaces, but cache is empty. Rollback to 12.2(33)SRE3 and netflow is working good (I see traffic in cache flow). Any idea?

Ops, sorry IOS 15.1(3)S2.

Port adapter gigabit router 7204vxr npe-400

Hi, I want to find a gigabit port adapter to my router. I found pa-ge port adpater but this port is for fiber link and I want a gigaport adapter for copper not fiber and I do not find that. Anyone knows a gigabit port for copper?

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
BTW, often "fiber" (e.g. SFP) ports support copper modules.
As others have noted, a NPE-400 is rather underpowered to support gig ports. (Wirespeed gig, for minimum sized Ethernet, in just one direction, requires up to 1.488 Mpps, or about 3 Mpps for full duplex. Consider a NPE-400 offers 400 Kpps, a NPE-G1 1 Mbps, a NPE-G2 2 Mpps, and a NSE-1 3.5 Mpps.)

PPPoE Cisco 6500 + 7600-SIP-400

Hello,
we use a lot of Cisco 6500 switches across our network. I bought one 7600-SIP-400 with one SPA-5X1GE-V2 module.
Unfortunatelly I have found that there is no command support for PPPoE in my IOS version 12.2 SXI13.
Can somebody tell me which IOS version do I have to use to get command support for PPPoE Server?
Thank you.
Milan

"Doesn't have to be a Cisco box. "
If you're still interested in solving this (or haven't already), you can mail me at [email protected]
Cheers,
Anton

Cisco 7206VXR and 2611XM

Hi.
I have the following routers 7206VXR(HO) and 2611XM (remote).
And they are currently connected via Serial using E1 link.
And we are planning to upgrade the link from E1 to (ATM)6-10 mpbs.
Could I install a DS3 card on both of the routers to accommodate the link upgrade?
Cisco 7206XVR --- PA-A3-T3 1-Port ATM Enhanced DS3 Port Adapter
Cisco 2611XM ---- ???
I believe that I could install a PA-A3-T3 card on the 7206. But I am not sure about 2611XM.
Advance thanks for your response.
Regards,
Gil

There is no DS-3 card for the 2600 series router. The 2600 is EoL so IMA probably isn't even supported. You'll need a new remote router.
Hope it helps.

Cisco 880 NPE how to change license?

Hello,
i have cisco 880 with NPE licence, but i need encryption on this device. I change IOS to c880data-universalk9-mz.151-3.T1.bin, but i still have NPE License and only Evalution without NPE. How can i have permanent license?
thanks.
show license all
License Store: Primary License Storage
StoreIndex: 0   Feature: advsecurity_npe                   Version: 1.0
        License Type: Permanent
        License State: Active, Not in Use
        License Count: Non-Counted
        License Priority: Medium
StoreIndex: 1   Feature: advipservices_npe                 Version: 1.0
        License Type: Permanent
        License State: Active, Not in Use
        License Count: Non-Counted
        License Priority: Medium
License Store: Evaluation License Storage
StoreIndex: 0   Feature: advipservices                     Version: 1.0
        License Type: Evaluation
        License State: Inactive
            Evaluation total period: 208 weeks 2 days
            Evaluation period left: 208 weeks 2 days
        License Count: Non-Counted
        License Priority: Low
StoreIndex: 1   Feature: advipservices                     Version: 1.0
        License Type: Evaluation
        License State: Inactive
            Evaluation total period: 208 weeks 2 days
            Evaluation period left: 208 weeks 2 days
        License Count: Non-Counted
        License Priority: Low
StoreIndex: 2   Feature: advipservices                     Version: 1.0
        License Type: Evaluation
        License State: Active, In Use
            Evaluation total period: 208 weeks 2 days
            Evaluation period left: 208 weeks 1 day
            Expiry date: Mar 24 2016 17:24:32
        License Count: Non-Counted
        License Priority: Low

you need new license file from Cisco for advipservices (Cisco 897VA comes with advipservices by default)
send the below details to Cisco licensing team and request for new licese file
Router#show license udi
Once you have the new lic file from Cisco - copy it to router flash and type below command to active it
Router#license install flash:.lic
Installing licenses from "flash:.lic"
Installing...Feature:advipservices...Successful:Supported
1/1 licenses were successfully installed
0/1 licenses were existing licenses
0/1 licenses were failed to install
Router#
once done - reload the router.
Hope this helps

PPPoE Cisco 7206VXR + NPE-400

Similar Messages

Maybe you are looking for