PPPoE Connection Drops streaming video on my Linksys WRK54G

So I just set up my Linksys WRK54G Version 1.1 to handle my PPPoE connection, meaning I entered the username and password assigned to me via my ISP. It works for a bit and then seems drop the connection all together. When this occurs, I cannot even ping the router (192.168.1.1). I have to unplug the AC Adaptor and then plug it in, inorder for the connection to pick up again. It seems when I try to access streaming video from a certain site (http://www.mtv2.com/#videoPremiere/1552982) and I have PPPoE setup via my router, the connection drops. If I change the setting to "Obtain an IP Automatically" and send my PPPoE credentials through my Windows XP client all is well. No issues what so ever.
I called Linksys and they had me try setting my MTU to 1400 but that did nothing. I have the most recent firmware as well. He then said that I will need to call my ISP and increase the bandwidth on my modem to get it to work (connect directly to my modem).
I have since reset the router, downloaded the newest episode of "Heroes" and fired up You Tube and watched a few streaming videos while grabbing the torrent. Everything looked ok.
I then went back to the MTV2 link I posted above (http://www.mtv2.com/#videoPremiere/1552982) and clicked play. At the same time I set up a continuous ping to the router. Sure enough, the connection dropped completely. Unplug the AC Adaptor to the router for 1 second, plug it back in and all is well. I am truly stumped here.
Is the issue perhaps a port issue with the video I am trying to stream from MTV2? It seems regular stress tests work ok.
PS - It seems someone else was having a similar problem here: http://www.dslreports.com/forum/rema...?hilite=wrk54g
UPDATE: I went to bed and woke up and my connection has dropped completely, and I was not even downloading anything?! Can someone please help me with this issue?

well...i guess u have tried almost everything possible on the router...try TCP optimiser .. this should adjust the MTU settings of the NIC card on the computer....
if u are having issues on the wireless computer, change channel - 1 or 11 , change beacon interval - 50 , RTS and fragmentation threshold - 2304 ...

Similar Messages

Lose connection watching streaming video

I bought a WRT54G v7.2 router some time ago, it works perfect but i had one little problem which plenty of people have reading this forum.
I'll put this new message here because people have thesame problem using different routers.
My router kept disconnecting streaming video on the web, it caused a hell of a headache because i tried everything suggested on the forum.
But i can tell you it's not a router problem according to me, i tried watching streams with VLC media player which i downloaded for free on the web and now i can watch streams without losing my connection.
VLC streams UDP, RTP, HTTP, HTTPS, MMS and RTSP.
I don't have a sollution for streaming with Realplayer or other programs but for a lot of streams VLC works, i hope this will solve some people's problems.
You can download VLC for free here http://downloads.videolan.org/pub/videolan/vlc/0.8.6h/win32/vlc-0.8.6h-win32.exe
People have a million faces.
Evil just one.

Tried that too, didn't work either...
People have a million faces.
Evil just one.

Safari no longer can show streaming video from Linksys webcams?

Since upgrading my iPhone and iPad to iOS6 yesterday, Safari no longer displays the streaming video from my Linksys webcams. I can trick it into displaying a still image by going to the camera's main page then hitting the browser back button to the page that should show the stream. This problem is also reported in the Safari on Mountain Lion community with no apparent fix for that platform. Any ideas?

I have this same exact problem my iPhone 4s as well as my iPad 2nd gen and my iPod Touch 4 gen,,,,... Tried clearing history and cookies and it worked one time on some of my cameras but then almost immediately went back to the problem you just described.
A few of the cameras were streaming well when I first tried accessing them from my iPod touch but after viewing a couple of the cameras none of them worked from then on. At least we know that Safari ios6 has the ability to successfully steam the cameras but something is happenening after you begin accessing the cameras. Its like something in Safari kicks in which prevents the actual streaming. The inter face all around the steaming box is all there and I can easily access the utilities sections of the cameras. Its just a streaming issue I think...
Anyone have any idea what in Safari could be blocking the streaming? Thanks!

WRT54G version 3.0 Streaming Video Issue

I have a WRT54G v3.0 wireless router that constantly drops connection when I try to stream video from the internet. If I eliminate the router and connect my laptop or desktop directly to my cable modem streaming video works perfect. Once I put the wireless router back into play and try to stream video I lose connection to the router. Normal internet use (e-mail, sports sites, etc.) work fine but as soon as I go to a site like youtube or espn and try to stream video the wireless connection drops. I have read numerous message boards that talk about firmware upgrades that will fix the problem but all of the message boards talk about WRT54G versions other than mine. Can anyone out there tell me why my WRT54G v3.0 router constantly drops connection when streaming video as well as tell me how to fix it?
By the way I currently have firmware version 3.03.6 (Jan 6, 2005) installed

I think the latest for v3 is firmware 4.21.1. Check out your model and version on http://www.linksys.com/download
The box said windows xp or better... So I installed Linux!

FLVPlayback and streaming video

I am reading about the different between progressive and
streaming video on the web. I want to use FLVPlayback to play
streaming video. In Flash help, to use streaming video we have to
create a connection to server right? And the code to connect to
streaming video on the server (FCS or FMS) is:
nc = new NetConnection();
nc.connect( url);
ns = new NetStream(nc);
ns.connect();
Also in the Flash help, in the FLVPlayback section, how to
play video using FLVPlayback is shown, but I could not see anything
related to the connection or NetStream variable as the above code.
So how can the FLVPlayback play streaming video? Could anyone help
me please?

Unless the video is completely downloaded to the iMac you can not rule out the Internet connection.
Since it plays all other video with no problem the downloading stream would seem to be the source of the problem.
I had cable modem and it is no guarantee of a fast connection. Also even having a fast connection on one end doesn't mean that the source of the video is pushing it all that fast.

AS2 to AS3 Streaming Video Player

Ok so Im trying to convert a video play that i made in AS2 to
AS3 (I had a problem with nested movie clips and the control bar
and i want to learn AS3) and i am having troblem even connecting to
my rtmp server. With the player i made in AS2 i was able to connect
and stream video no problem. But with AS3 I am not even able to
connect to the rtmp server. Here is the AS2 code and the AS3 code:
AS3:
var video:Video = new Video(853,480);
addChild(video);
var nc:NetConnection = new NetConnection();
nc.connect("rtmp://[ip of server]/sumone4life/videos");
var ns:NetStream = new NetStream(nc);
ns.addEventListener(NetStatusEvent.NET_STATUS,
onStatusEvent);
function onStatusEvent(stat:Object):void
trace(stat.info.code);
var meta:Object = new Object();
meta.onMetaData = function(meta:Object)
trace(meta.duration);
video.attachNetStream(ns);
ns.play("AdobeBand_640");
And I get the error:
ArgumentError: Error #2126: NetConnection object must be
connected.
at flash.net::NetStream/construct()
at flash.net::NetStream()
at videoPlayer_fla::MainTimeline/frame1()
Error #2044: Unhandled AsyncErrorEvent:. text=Error #2095:
flash.net.NetConnection was unable to invoke callback onBWDone.
error=ReferenceError: Error #1069: Property onBWDone not found on
flash.net.NetConnection and there is no default value.
at videoPlayer_fla::MainTimeline/frame1()
Flash media server 3 Administrative Panel also shows that I
am infact connected to the server but there is nothing being
streamed from the server.
AS2 Works:
//Video Loading Controls
var fileName:String = "AdobeBand_640";
var nc:NetConnection = new NetConnection();
var ns:NetStream;
nc.onStatus = function(info){
trace(info.code);
if(info.code == "NetConnection.Connect.Success"){
playVideo();
function playVideo(){
ns = new NetStream(nc);
ns.onMetaData = onMetaDataHandler;
videoObject.attachVideo(ns);
_root.createEmptyMovieClip("vSound",
_root.getNextHighestDepth());
vSound.attachAudio(ns);
ns.setBufferTime(5);
ns.onStatus = function(info){
trace(info.code);
if(info.code == "NetStream.Buffer.Full"){
bufferClip._visible = false;
if(info.code == "NetStream.Buffer.Empty"){
bufferClip._visible = true;
if(info.code == "NetStream.Play.Stop"){
ns.seek(0);
ns.play(filename);
//connects the stream
nc.connect("rtmp://[ip of server]/sumone4life/videos");
Can anyone offer any insite as to why it would be workin in
AS2 and not in AS3? Or what i am doing wrong...

I have a similar problem. Did you get your to work?

Why does my ipad 2 keep dropping the connection to my BT Home Hub, whilst streaming video, since upgrading to IOS 6?

Ever since i have upgraded to IOS6 My connection to my BT Hub 3 wifi router keeps dropping out whenever i am streaming video. I have an Apple TV connected as well which is fine as are other devices, its just the Ipad since the move to IOS6. It is really frustrating and i had hoped the 6.01 release would have resolved it, but it didnt. I have seen other similar comments, i just want to know if this is a common known fault which Apple are going to fix.
The strength of Apple has always been 'it just works' , i can't help but feel that there are cracks appearing in this.
David

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Need Help Streaming Video From Web Server Built Into Application - Linksys WRT54g Router

Very much appreciate any help getting streaming video feed from web server built into video application to work properly using port forwarding on my Linksys WRT54g wireless router.
Here is the situation:
My PC is connected to the internet via a Linksys WRT54g wireless router.
The Windows XP Pro SP2 firewall is enabled, with a firewall exception established for the video camera application.
On the router, forwarding of port 80 is enabled for the LAN IP address of the PC running the video application with an embedded web server, and the web server in the video camera application is also set to use port 80.
I have a free DYNDNS account and also run the DYNDNS updater program on the PC running the video application with embedded web server. According to the DYNDNS web site and the DYNDNS updater program, the IP address assigned to the machine running the video application with embedded web server is set correctly in my dyndns account.
When I open a browser (Explorer or Firefox) on the PC running the video camera application with embedded web server, I am able to connect to the video application's web server by going to the dyndns address linked to the machine running the video application. The video application's web server is set to use the dyndns address. That's the good news. The bad news is that I can't connect to the video application's web server from any machine that connects to the internet that uses a router other than the router used by the PC running the video application. I am only able to connect to the streaming video from the application's web server only on machines that connect to the internet using the same (home) router used by the PC that is running the video application.
Since I am able to connect to the video app's embedded web server successfully on the machine running the video application, it seems that at least something about the current port forwarding settings is correct. For example, if I uncheck 'enable' for forwarding of port 80 on the router settings page, I am no longer able to connect to the video app's web server when I try to do so in a browser running on the machine running the video app. When I re-enable port 80 forwarding on the router, I am again able to connect to the web server of the video application on the machine running the video app. I thought that by enabling forwarding of port 80 on the router and associating that port with the LAN IP of the machine running the video application, it would be possible to connect to the streaming video of the video app's embedded web server from ANY machine connected to the internet, but that is not the case. There must be some other router settings to update/change in order to get the port forwarding working to enable a successful connection to the video web server, but I am stumped. Very grateful for any suggestions as to how to get this working properly.
Thanks in advance...

The firewall log can be configured on the third tab in the window for the firewall settings, where you can turn the firewall on and off completely.
From your tests, though, it does not seem to be the firewall. However, to be sure, it would be good to check the log. It will help to eliminate the firewall as the culprit and you may find it handy in the future, too. ;-) Just don't forget to turn the log off again after you are done because it may cause some performance penalty on your system while on.
From what you write, it seems as if I should give a little networking background on the ip addresses you'll see. Your setup is (or should be) a modem connected to the WAN/Internet port of the WRT. The computer is connected into a LAN port of the WRT.
Your router has two IP addresses (that's what makes it a router): a WAN address and a LAN address. The WAN address is the address assigned by the ISP. It is a normal internet IP address. Everyone is able to send packets to this IP address. The WAN address is the one reported by whatismyipaddress.com, it should be listed in the dyndns record and it is the address that your router shows on the Status page. It's the public IP address of your router. Dyndns maps your dyndns.org name to that IP address.
Your router also has an IP address on the LAN side. You can configure it to be whatever you want. The default is 192.168.1.1 with netmask 255.255.255.0 and it is better to leave it like that or at least inside the network 192.168.*.*. 192.168 is a special, reserved IP address range for private networks. Basically, routers in the internet are not supposed to forward addresses in this range. That makes them suitable for private LANs as the packets never can get anywhere. Most people using Linksys routers have there LAN in 192.168.1.*.
The router acts as gateway, which means it forwards packets from PCs in the LAN to the internet and back. As all your PCs in your LAN share a single WAN IP address, the gateway does address translation (NAT). This works only in one direction: from the inside to the outside. The router remembers when a PC in your LAN sends something out and accepts the responses in and sending them back to the PC. If something comes in from the internet which cannot be associated with a ongoing communication the packet is dropped unless you use port forwarding.
All computers in your LAN either have a static IP address assigned or use DHCP to get it automatically. The router has a DHCP server as well which gives out IP address from 192.168.1.100-149 if not changed. With a router with default settings static IP addresses can be in the range of 192.168.1.2-99 and 150-254.
ipconfig /all reports your IP address in your LAN, i.e. an address 192.168.1.*. The gateway in this output should be 192.168.1.1 which is your router. And packet no in the LAN address range 192.168.1.* is send to the router which forwards the packets into the internet.
An address 192.168.1.* should not appear as internet address in the Status page of the router nor should it appear at dyndns.
Port forwarding is used to operate a server in the LAN. By default, a server in the LAN cannot be reached from the internet. You have to configure port forwarding for this. You configure that traffic bound for a specific port (e.g. TCP port 80 for http) on your WAN IP address is forwarded to the same port on a specific LAN IP address. If your server runs on 192.168.1.50 than traffic to your WAN IP address port 80 is forwarded to 192.168.1.50 port 80. That way your HTTP server can be reached from the internet. As you can only configure a fixed IP address in port forwarding it is recommended that the server uses a static IP address and not DHCP as in the latter case the IP address may change over time...
O.K. so much for networking. I hope that makes things a little clearer and you can verify that your setup is how it is intended to be.
I suggest the following: on the router's security page there is an option to block WAN requests. Remove the check if it is set (meaning: do not block). After you did that change you should be able to ping your WAN address (e.g. ping xxxx.dyndns.org) from the internet. That way we know that it is on the correct address.
Also on the Administration page make sure that remote management is disabled (should be like that per default) or that the management port is NOT 80 but for example 8080. What is your your UPnP settings on the same page?
O.K. that should be enough for the moment...

Ipad Air drops wifi when streaming videos, browsing. iPhone 4S fine

I recently bought an ipad air.
I have been experiencing numerous problems regarding the wifi connection and I have contacted apple support twice about it but I thought I'd ask here before returning my device for a refund.
Basically, ipad air is behaving inferior to all my other apple devices.
Problems:
Wifi drops randomly and sometimes it comes back by relaunching the application (e.g. Safari) or sometimes I have to turn of wifi off and on again to restore connection. This especially happens when I watch streaming videos either on YouTube app or safari.
At the same time when I perform speedtests ipad air gives always mixed results most of the time being slower than my other devices (iPhone 4S , iPhone 3GS, MacBook Pro 2011).
What I have tried Already:
Resetting the network settings
Restarting the ipad and the router (bt hub5)
Switching between 2.4 and 5 ghz networks
The most important thing is that all my other devices , my iPhone 4S , my iPhone 3GS and my MacBook Pro work great in every network where the ipad air seems to either give poor performance or drop the connection randomly.
I would be happy to know if there is an issue with ipad airs that is going to be resolved with an upcoming OS update, I am patient. It would save me the hassle of returning the ipad for a refund.
Thank you so much in advance for any help.

Hi Finalizer,
Thanks for visiting Apple Support Communities.
If you have not yet done so, I recommend backing up your iPad Air and restoring the device as new:
iOS: Back up and restore your iOS device with iCloud or iTunes
http://support.apple.com/kb/HT1766
iTunes: Restoring iOS software
http://support.apple.com/kb/HT1414
After the device is restored and updated to the latest version of iOS 7, test the Wi-Fi connection with Safari or another app before restoring a backup of your data.
All the best,
Jeremy

Streaming video disconnects my connection

Hi all
I am having a problem with my linksys befw11s4 router. The problem started when I upgraded the firmware on the router. Whenever I try and stream video from a source such as MLB.com my internet connection dies and I have to unplug/replug in my router and turn off/turn on my modem to reconnect.
If I connect via a manually made broadband connection under network settings it works, but this connection only works if I time it so I hit "connect" instantly when my modem connection light turns on. It's very weird and annoying. Any help?

ensure that the router has the latest firmware and change the MTU settings to 1452..
change the wireless channel - 11
beacon interval - 50
Fragmentation threshold - 2306
RTS Threshold - 2307

How to connect flash video player(like youtube) to live streaming video the programm like

How to connect flash video player(like youtube) to live
streaming video the programm like webcamXP?
Or through a browser to look in a videoplayer video from
other usual personal computer with the program for a video
broadcasting from the web chamber.

you can use google to search for tutorials on skinning the component.

Unable to configure Linksys E2500 to use PPPoE connection

I am using the Ubuntu Linux 12.04 operating system and have been able to use the Linksys E2500 router with Automatic Configuration – DHCP setting and my modem in PPPoE mode to use my DSL connection. But I would like to be able to use my router with the PPPoE connection setting so I can use a firmware like Tomato which has more advanced features like bandwidth logging.
I was able to log into the configuration page of my SpeedTouch ST516 modem and set it to bridge mode according to the instructions here: http://www.speedtouch.ca/bridgemode.php
I then tried to set up the router to use PPPoE according to the instructions here: http://kb.linksys.com/Linksys/ukp.aspx?pid=80&vw=1&articleid=3687
I get the message "Can not get an IP address from PPPoE" again when I try to set up the connection in step 4. Resetting the router does not help. I also tried running 'sudo service networking restart' and the 'sudo dhclient -r; sudo dhclient' in Ubuntu's terminal but still got the same message.
I double checked that I used right login information and vpi from my ISP. I used the same info to configure the modem to PPPoE mode again so I can connect to the internet. I had to reset the modem back to factory defaults using the reset button at the back to access the modem configuration page after I disconnected the ethernet cable from the router and plugged it into the modem.
Is there a possible bug with using PPPoE with this router? Is there anything else I can try besides what is stated in the instructions linked to above?

jaymay
"If you are getting an error "Can't get an IP from PPPoE Server", that would mean that it's possible that the account information you've typed in is incorrect or the modem is not set properly to bridged mode. You can test this by connecting your computer directly to the modem and create a PPPoE dialer. If it will let you connect successfully then you are using the correct username and password. If not then you might have to verify the correct info from your ISP."
> Again, "I double checked that I used right login information and vpi from my ISP. I used the same info to configure the modem to PPPoE mode again so I can connect to the internet." And yes I was also able to connect with a PPPoE dialer and computer directly connected to the modem.
"It could be possible that what you just need to do in the router is to change it's LAN IP address to a different range compared to what you are getting from the modem to avoid IP conflict. For more information about setting up the router with DSL connection, you may refer to this link: Setting up a Linksys router for DSL Internet connection."
> That link is exactly the same link in my sentence: "I then tried to set up the router to use PPPoE according to the instructions here: http://kb.linksys.com/Linksys/ukp.aspx?pid=80&vw=1&articleid=3687"
The router ip address used is set to http://192.68.2.1 which differs from the ip addresses of the modems I tried.

Having trouble streaming videos. Is there anything I can do to speed up the connection?

Having trouble streaming videos. Is there anything I can do to speed up the connection?

Here is the information....
Problem description: Having trouble with streaming videos. Slow and unresponsive. EtreCheck version: 2.1.5 (108) Report generated December 28, 2014 at 10:27:27 PM EST Click the [Support] links for help with non-Apple products. Click the [Details] links for more information about that line. Click the [Adware] links for help removing adware. Hardware Information: ℹ️ iMac (24-inch, Early 2008) (Verified) iMac - model: iMac8,1 1 2.8 GHz Intel Core 2 Duo CPU: 2-core 2 GB RAM Upgradeable BANK 0/DIMM0 1 GB DDR2 SDRAM 800 MHz ok BANK 1/DIMM1 1 GB DDR2 SDRAM 800 MHz ok Bluetooth: Old - Handoff/Airdrop2 not supported Wireless: en1: 802.11 a/b/g/n Video Information: ℹ️ ATI Radeon HD 2600 Pro - VRAM: 256 MB iMac 1920 x 1200 System Software: ℹ️ OS X 10.10.1 (14B25) - Uptime: 7:20:12 Disk Information: ℹ️ Hitachi HDP725032GLA380 disk0 : (320.07 GB) EFI (disk0s1) <not mounted> : 210 MB Macintosh HD (disk0s2) / : 319.21 GB (230.03 GB free) Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB USB Information: ℹ️ Apple Inc. Built-in iSight Apple Inc. BRCM2046 Hub Apple Inc. Bluetooth USB Host Controller Apple Computer, Inc. IR Receiver Gatekeeper: ℹ️ Mac App Store and identified developers Adware: ℹ️ Downlite [Remove] Problem System Launch Daemons: ℹ️ [killed] com.apple.wdhelper.plist one process killed due to memory pressure Launch Agents: ℹ️ [loaded] com.coupons.coupond.plist [Support] [invalid?] com.vsearch.agent.plist Adware! [Remove] [running] jp.co.canon.ScanGearMF.appl.Canon-MF-Scan-Agent.plist [Support] Launch Daemons: ℹ️ [loaded] com.adobe.fpsaud.plist [Support] [invalid?] com.vsearch.daemon.plist Adware! [Remove] [invalid?] com.vsearch.helper.plist Adware! [Remove] User Login Items: ℹ️ iTunesHelper Application (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app) Microsoft Messenger Application (/Applications/Microsoft Office 2008/Microsoft Messenger.app) apple-scc-20141118-211745 UNKNOWN (missing value) Internet Plug-ins: ℹ️ FlashPlayer-10.6: Version: 16.0.0.235 - SDK 10.6 [Support] CouponPrinter-FireFox_v2: Version: 5.0.3 - SDK 10.6 [Support] Flash Player: Version: 16.0.0.235 - SDK 10.6 [Support] QuickTime Plugin: Version: 7.7.3 Default Browser: Version: 600 - SDK 10.10 3rd Party Preference Panes: ℹ️ Flash Player [Support] Time Machine: ℹ️ Auto backup: YES Volumes being backed up: Macintosh HD: Disk size: 319.21 GB Disk used: 89.18 GB Destinations: moms stuff [Local] Total size: 0 B Total number of backups: 1 Oldest backup: 2014-11-19 03:42:00 +0000 Last backup: 2014-11-19 03:42:00 +0000 Size of backup disk: Too small Backup size 0 B < (Disk used 89.18 GB X 3) Top Processes by CPU: ℹ️ 14% VTDecoderXPCService 3% WindowServer 1% coreaudiod 0% AppleSpell 0% askpermissiond Top Processes by Memory: ℹ️ 86 MB Safari 52 MB com.apple.WebKit.WebContent 49 MB Mail 34 MB WindowServer 28 MB Microsoft Word Virtual Memory Information: ℹ️ 42 MB Free RAM 558 MB Active RAM 528 MB Inactive RAM 347 MB Wired RAM 3.53 GB Page-ins 67 MB Page-outs Diagnostics Information: ℹ️ Dec 28, 2014, 03:07:57 PM Self test - passed Dec 27, 2014, 03:32:55 AM /Library/Logs/DiagnosticReports/discoveryd_2014-12-27-033255_[redacted].crashPr oblem description: Having trouble with streaming videos. Slow and unresponsive. EtreCheck version: 2.1.5 (108) Report generated December 28, 2014 at 10:27:27 PM EST Click the [Support] links for help with non-Apple products. Click the [Details] links for more information about that line. Click the [Adware] links for help removing adware. Hardware Information: ℹ️ iMac (24-inch, Early 2008) (Verified) iMac - model: iMac8,1 1 2.8 GHz Intel Core 2 Duo CPU: 2-core 2 GB RAM Upgradeable BANK 0/DIMM0 1 GB DDR2 SDRAM 800 MHz ok BANK 1/DIMM1 1 GB DDR2 SDRAM 800 MHz ok Bluetooth: Old - Handoff/Airdrop2 not supported Wireless: en1: 802.11 a/b/g/n Video Information: ℹ️ ATI Radeon HD 2600 Pro - VRAM: 256 MB iMac 1920 x 1200 System Software: ℹ️ OS X 10.10.1 (14B25) - Uptime: 7:20:12 Disk Information: ℹ️ Hitachi HDP725032GLA380 disk0 : (320.07 GB) EFI (disk0s1) <not mounted> : 210 MB Macintosh HD (disk0s2) / : 319.21 GB (230.03 GB free) Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB USB Information: ℹ️ Apple Inc. Built-in iSight Apple Inc. BRCM2046 Hub Apple Inc. Bluetooth USB Host Controller Apple Computer, Inc. IR Receiver Gatekeeper: ℹ️ Mac App Store and identified developers Adware: ℹ️ Downlite [Remove] Problem System Launch Daemons: ℹ️ [killed] com.apple.wdhelper.plist one process killed due to memory pressure Launch Agents: ℹ️ [loaded] com.coupons.coupond.plist [Support] [invalid?] com.vsearch.agent.plist Adware! [Remove] [running] jp.co.canon.ScanGearMF.appl.Canon-MF-Scan-Agent.plist [Support] Launch Daemons: ℹ️ [loaded] com.adobe.fpsaud.plist [Support] [invalid?] com.vsearch.daemon.plist Adware! [Remove] [invalid?] com.vsearch.helper.plist Adware! [Remove] User Login Items: ℹ️ iTunesHelper Application (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app) Microsoft Messenger Application (/Applications/Microsoft Office 2008/Microsoft Messenger.app) apple-scc-20141118-211745 UNKNOWN (missing value) Internet Plug-ins: ℹ️ FlashPlayer-10.6: Version: 16.0.0.235 - SDK 10.6 [Support] CouponPrinter-FireFox_v2: Version: 5.0.3 - SDK 10.6 [Support] Flash Player: Version: 16.0.0.235 - SDK 10.6 [Support] QuickTime Plugin: Version: 7.7.3 Default Browser: Version: 600 - SDK 10.10 3rd Party Preference Panes: ℹ️ Flash Player [Support] Time Machine: ℹ️ Auto backup: YES Volumes being backed up: Macintosh HD: Disk size: 319.21 GB Disk used: 89.18 GB Destinations: moms stuff [Local] Total size: 0 B Total number of backups: 1 Oldest backup: 2014-11-19 03:42:00 +0000 Last backup: 2014-11-19 03:42:00 +0000 Size of backup disk: Too small Backup size 0 B < (Disk used 89.18 GB X 3) Top Processes by CPU: ℹ️ 14% VTDecoderXPCService 3% WindowServer 1% coreaudiod 0% AppleSpell 0% askpermissiond Top Processes by Memory: ℹ️ 86 MB Safari 52 MB com.apple.WebKit.WebContent 49 MB Mail 34 MB WindowServer 28 MB Microsoft Word Virtual Memory Information: ℹ️ 42 MB Free RAM 558 MB Active RAM 528 MB Inactive RAM 347 MB Wired RAM 3.53 GB Page-ins 67 MB Page-outs Diagnostics Information: ℹ️ Dec 28, 2014, 03:07:57 PM Self test - passed Dec 27, 2014, 03:32:55 AM /Library/Logs/DiagnosticReports/discoveryd_2014-12-27-033255_[redacted].crash

Live webcam video becomes choppy after 600 connections per stream

Hi!
Server conf:
2 x Intel(R) Xeon(R) CPU L5410 @ 2.33GHz
16Gb RAM
2 Gbit ethernet channel
OS - Linux CentOS 5.5 x86_64
FMS4 Interactive
Live stream parameters:
320х240
qua_=87
bw_=200000
kf_=5
fps_=18
So, after approximately 600 connections to one stream video becomes choppy (periodically freeze, slow motions). CPU-usage at this time is 100-120% (maximum is 800%, 100% per each core), network usage is 500 Mbit/sec.
But second live stream(with few connections) at this server looks fine simultaneously with 600 connections at first stream.
Experiments with recommendation in "Configuring performance features" documentation chapter(enabling/disabling aggregate messages and configure the size of stream chunks) do not help.
Please, help me to find bottleneck!
Thanks for answers.
Apologisw my english.

What Flash Player version are you using at client-side?? have you tried changing the FP to the latest (in case if you are already using latest FP, then try to switch to some previous version) and see if this issue still remains?
Regards,
Shiraz Anwar

Live stream - How To Detect connection success AND video stream receiving?

Hi,
I'd like to know how to catch the Event when the NetConnection has successfully connected,
And after being connected, but nostream is published to the server yet.
I'd to catch the Event in OSMF Player, when a real video stream has started to be pusblished to server, and of course is received in the player.
Because i dont find the Event making a difference between connection and stream receiving.
Thanks.
Seb

you should watch for a NetStream.Connect.Closed NetStatusEvent being sent to the NetConnection object, where the event.info.stream object is the NetStream in question.

PPPoE Connection Drops streaming video on my Linksys WRK54G

Similar Messages

Maybe you are looking for