PPPoE on 7600

I need little confirmation, has any one tested the PPPoE, BRAS functionality on CISCO 7600 with SUP720+12.2SRC+SIP-400 topology, does it really work and does it really give some practical difference from 7200 NPE-G2.

I have these logs:
Feb 13 13:20:22.572: AAA/AUTHEN/PPP (0000015F): Pick method list 'default'
Feb 13 13:20:22.572: RADIUS/ENCODE(0000015F):Orig. component type = PPoE
Feb 13 13:20:22.572: RADIUS: AAA Unsupported Attr: interface         [194] 7
Feb 13 13:20:22.572: RADIUS:   33 2F 31 2F 30             [ 3/1/0]
Feb 13 13:20:22.572: RADIUS: AAA Unsupported Attr: client-mac-address[43] 14
Feb 13 13:20:22.572: RADIUS:   30 30 31 63 2E 37 65 36 30 2E 62 38      [ 001c.7e60.b8]
Feb 13 13:20:22.572: RADIUS(0000015F): Config NAS IP: 0.0.0.0
Feb 13 13:20:22.572: RADIUS/ENCODE(0000015F): acct_session_id: 341
Feb 13 13:20:22.572: RADIUS(0000015F): sending
Feb 13 13:20:22.572: RADIUS/ENCODE: Best Local IP-Address 80.78.66.245 for Radius-Server 80.78.66.72
Feb 13 13:20:22.572: RADIUS(0000015F): Send Access-Request to 80.78.66.72:1812 id 1645/71, len 91
Feb 13 13:20:22.572: RADIUS: authenticator D1 6A A9 97 1F 2E E2 A8 - 14 E1 15 64 EC AD F8 D3
Feb 13 13:20:22.572: RADIUS: Framed-Protocol     [7]   6   PPP                       [1]
Feb 13 13:20:22.572: RADIUS: User-Name           [1]   14 "ilir-optimal"
Feb 13 13:20:22.572: RADIUS: User-Password       [2]   18 *
Feb 13 13:20:22.572: RADIUS: NAS-Port-Type       [61] 6   Virtual                   [5]
Feb 13 13:20:22.572: RADIUS: NAS-Port            [5]   6   0
Feb 13 13:20:22.572: RADIUS: NAS-Port-Id         [87] 9   "3/1/0/1"
Feb 13 13:20:22.572: RADIUS: Service-Type        [6]   6   Framed                    [2]
Feb 13 13:20:22.572: RADIUS: NAS-IP-Address      [4]   6   80.78.66.245
Feb 13 13:20:22.576: RADIUS: Received from id 1645/71 80.78.66.72:1812, Access-Accept, len 66
Feb 13 13:20:22.576: RADIUS: authenticator 87 68 42 F1 C6 86 2D 73 - 00 E6 B1 F4 B0 CE 9D D5
Feb 13 13:20:22.576: RADIUS: Class               [25] 7
Feb 13 13:20:22.576: RADIUS:   53 76 63 3D 31             [ Svc=1]
Feb 13 13:20:22.576: RADIUS: Idle-Timeout        [28] 6   7200
Feb 13 13:20:22.576: RADIUS: Service-Type        [6]   6   Framed                    [2]
Feb 13 13:20:22.576: RADIUS: Framed-Protocol     [7]   6   PPP                       [1]
Feb 13 13:20:22.576: RADIUS: Framed-IP-Address   [8]   6   255.255.255.254
Feb 13 13:20:22.576: RADIUS: Reply-Message       [18] 15
Feb 13 13:20:22.576: RADIUS:   41 63 63 65 73 73 20 41 63 63 65 70 74     [ Access Accept]
Feb 13 13:20:22.576: RADIUS(0000015F): Received from id 1645/71
Feb 13 13:20:22.576: RADIUS/DECODE: Reply-Message fragments, 13, total 13 bytes
Feb 13 13:20:22.588: [333]PPPoE 330: State LCP_NEGOTIATION    Event SSS CONNECT LOCAL
Feb 13 13:20:22.592: [333]PPPoE 330: Segement (SSS class): UPDATED
Feb 13 13:20:22.596: [333]PPPoE 330: Segment (SSS class): BOUND
Feb 13 13:20:22.596: [333]PPPoE 330: data path set to Virtual Acess
Feb 13 13:20:22.596: [333]PPPoE 330: State LCP_NEGOTIATION    Event SSM UPDATED
Feb 13 13:20:22.596: AAA/BIND(0000015F): Bind i/f Virtual-Access2.1
Feb 13 13:20:22.596: [333]PPPoE 330: O
contiguous pak, size 20

Similar Messages

PPPoE Cisco 6500 + 7600-SIP-400

Hello,
we use a lot of Cisco 6500 switches across our network. I bought one 7600-SIP-400 with one SPA-5X1GE-V2 module.
Unfortunatelly I have found that there is no command support for PPPoE in my IOS version 12.2 SXI13.
Can somebody tell me which IOS version do I have to use to get command support for PPPoE Server?
Thank you.
Milan

"Doesn't have to be a Cisco box. "
If you're still interested in solving this (or haven't already), you can mail me at [email protected]
Cheers,
Anton

BRAS Config for MPLS carrying PPPoE

Hi all
DSLAM----(PPPoE)---7600----(Xconnect)----7600----(VLAN/PPPoE)---(BRAS ASR1K)
we currently have a distributed access network where the DSLAMs send us PPPoE packets which we are wrapping into xconnects back to a central BRAS.
the xconnects terminate on the upstream device to the BRAS. The BRAS is connected by a VLAN trunk and each DSLAM is identified by a unique VLAN-ID.
so the BRAS gets native PPPoE frames.
I wish to extend the MPLS to the BRAS itself. So that the xconnect ( or VPLS ) terminates on the BRAS itself.
I cant see how to stitch in the PPPoE features to get this to work.
I was thinking about an external looping cable on the same BRAS device but thats a bit crap
Is there a more elegant solution?
many thanks

Hi,
You can try pseudowire headend configuration. But I am not sure its avaliable for AS1K.
http://www.cisco.com/en/US/docs/routers/crs/software/crs_r4.1/lxvpn/configuration/guide/vc41vpls.html#wp1323446

7600 as BRAS

Does 7600 support pppoe termination? What modules is it necessary to use for termination?

Антон
7600 will not terminate VPDN connections (pptp or l2tp), you need MWAM module
http://newsroom.cisco.com/dlls/Cisco_76000_Multiprocessor_WAN_Application_Module.pdf

Carrying PPPoE over MPLS....

We are stuck in a situtation which is as follows:
Customer(PPPoE)------7600----MPLS---BRAS
The PPPoE session is to be terminated on the BRAS (a cisco 7200). The 7600 does not support the PPPoE Relay feature (which would've allowed the PPPoE session to be carryied over L2TP through the MPLS core). I do not want to use a L2 VPN to do this. Any suggestions???

Hey there... I m too stabbing the same problem... though unsuccessfully.. as a temporary arrangement I have installed another 'PPPoE Relay enabled' router... waiting for TAC guys to come back with some answers... would really like to know the solution for this one !!!
~sultan

Number of PPPoE sessions on ISR/ASR routers

Hello,
I am working on a design wherein i need some inputs in terms of the number of PPPoE sessions that can be terminated on the ISR-G2 devices especially 3945/3945 E routers and also ASR1K routers
If there is any official cisco document on the same it would highly help
Also any recomendations on using the 3945s as broadband routers ???...
Regds,
Sudhir

Hi,
I'm looking for the same document. For Cisco 10K, ASR1000 and also 7600.
I'm also interested if someone can share real experiance (not only on-paper number).
Thanks for your help.
Rgds,
Jerome

HP 7600 AIO Leopard update

I recently found the new release of HP 7600 software for Leopard. After some trouble, I was able to install it (apparently) successfully for our HP Officejet Pro L7650 (which apparently is the Costco version of the L7680).
I have a LAN based on an Airport Extreme and an ethernet switch, and the first problem for me was simply understanding how to hook up the cables. Simply running a USB from the Airport got me printing but nothing else (as your literature states). To get full functionality, however, I connected the L7650 to the ethernet switch.
In running the install program on each of our three computers, the program came to a point during setup where it said it could not find the AIO and concluded that the install program could not continue. I found, quite accidentally, that disconnecting and then reconnecting the ethernet cable from the switch to the AIO enabled the program to proceed. With that quirk, the software was installed on two computers; the third required removal of all the HP software I could find before it, too, accepted the new install.
After I got it installed and working, I received the following from HP "Customer Care" in response to an annoyed letter from me. I offer it without comment; I have not tried it:
*****beginning of HP communication quote******
Donald, here is the link from the HP.com website to download the required software for this printer to work with the Leopard operating system.
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-56883-1 &lc=en&cc=us&dlc=en&product=3203059&os=219&lang=en
Please follow these next steps provided in order to manually uninstall all software pertaining to this printer from your computer.
Double-click Macintosh HD .
Open the Applications folder.
Open the Utilities folder.
Double-click Activity Monitor . The Activity Monitor window should open. If the window does not open, select Window , then Activity Monitor .
When Activity Monitor opens, look for the following processes:
NOTE: Not all of these processes may be running.
HP Communications
HP Director
HP Image Zone
HP Trap Monitor
pipedaemon
HPIO Classic Proxy
HPIO Classic Proxy 2
Hpdot3d
HP AiO Notifications.app
Print daemon
Highlight them one at a time and click the Quit Process icon.
Click Force Quit to quit the process.
Close Activity Monitor after quitting all the found items.
Remove the following files and folders from the partition where the All-in-One software is installed:
NOTE: Some of the files described in the following steps may not be found.
Macintosh HD/Applications/HP AiO Software/Hewlett-Packard folder
Macintosh HD/Library/Application Support/hp folder
In Macintosh HD/Library/Caches , drag the following files to the trash:
Any files beginning with HP or hp
Any files beginning with Hewlett-Packard
Any files beginning with com.hp
Macintosh HD/Library/Documentation/Help/HP Photo and Imaging Help
Macintosh HD/Library/Frameworks/HPServicesInterface.framework
Macintosh HD/Library/Image Capture/TWAIN Data Sources/HP All-in-One Scan.ds
In Macintosh HD/Library/Image Capture/Scripts , drag the following files to the trash:
Import and View with iPhoto
View with HP
In Macintosh HD/Library/Preferences , drag the following files to the trash:
Hewlett-Packard Preferences
HP Registry
Any files that begin with com.hp
Move Macintosh HD/Library/Preferences/loginwindow.plist to the desktop.
NOTE: Not removing the file loginwindow.plist during the manual uninstall could cause the uninstall to be unsuccessful.
In Macintosh HD/Library/Printer/hp , drag the following files and folders to the trash:
aio
Frameworks folder
hpio folder
pipedaemon
Print Daemon
Utilities folder
In Macintosh HD/Library/StartupItems , drag the following folders to the trash:
HP IO
HP Trap Monitor
NOTE: On some systems it is necessary to enter the user password to delete those both folders from the StartupItems folder. Do the identification with entering the OS X admin password.
In Macintosh HD/Users/USERNAME (this should have a symbol of a house next to it)/Library/Preferences , drag the following folders to the trash:
Any files beginning with com.apple.print
Any files beginning with com.hp
Any files beginning with Hewlett-Packard
Any files beginning with HP or hp
In MacintoshHD/Users/USERNAME/Library/Printers , drag any All-in-One printers listed here into the trash.
Drag the HP Director or HP Image Zone icon from the Dock and drop it on an empty space on the desktop. The icon will disappear.
Close all open windows.
Restart.
Empty the Trash.
Quit any HP processes that may prevent items from being deleted from the trash.
After logging in, verify and possibly repair any permissions that might have been affected using these steps:
Open Macintosh HD/Applications/Utilities/Disk Utility and double-click on Disk Utility .
Upon the left side, select the Macintosh HD . It will be indented and usually is the second entry in that list.
On the right side beneath the white box select Repair Disk Permissions . This process may take several minutes.
Close Disk Utility by single-clicking the red dot at the top left of the dialog box.
Install the printer software. If there is other HP hardware that needs to be re-installed, install it afterwards.
Double-click the downloaded file containing the software for the printer.
Double-click the Installation file; it will be either All-in-One Installer or Vise Installer .
Proceed through the questions asked. If prompted for an account and password, use the information for the user account you are currently logged into.
NOTE: After installation is finished the HP Setup Assistant must be completed.
In some situations the All-in-One Setup Assistant will ask you to open the Printer Setup Utility in order to add the printer manually. If prompted with this, use the following steps:
If the All-in-One is directly connected to the Mac with a USB cable:
Click Printer Setup Utility .
When the Printer Setup Utility opens, click Add .
Single-click the entry for the HP All-in-One which is connected by USB.
Click Add .
*****end of HP communication quote******

Nobody has any ideas?

No wireless Internet access - DSL PPPoE modem

I have seen a few threads in the forum related to similar issues but have been unable to fully resolve my problem. I am trying to set up my Airport Express with a DSL router that runs PPPoE. When I attempt to set up the connection, my Express cannot locate the PPPoE server.
From what I understand, I need to disable PPPoE. I have done this on the Airport Express in the System Preferences (Network) but cannot figure out how to disable it on the Built-in Ethernet connection while running OSX 10.5.1.
The Airport Express indicator is solid green but I am unable to get through to the Internet. It just keeps looking for the connection but has yet to grab it.
I have used the device successfully with a DHCP set-up without any trouble but am visiting family with a different type of service. Any suggestions?
Right now I'm using an Alcatel Speed Touch broadband modem and have a Dynex Ethernet Switch that's splitting the connection between my family's PC and my Airport Express. If I hook up an Ethernet cable to my MacBook Pro and connect with the Built-in Ethernet connection, I have no trouble. So it's obviously something with my Airport Express settings.
Here's a summary of the Airport Express set-up:
Running firmware 6.3
Internet connection: Connect using PPPoE (Service Name left blank)
PPPoE: Connection always on
Wireless Security: WEP 128 bit
Any advice is more than welcome.

See if installing this driver helps any:
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=cp-97536-1&cc=us&dlc=en&lc=en&...
Also see this to setup your wireless router, near the top right hand side be sure to select Windows 7
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=cp-97536-1&cc=us&dlc=en&lc=en&...
Please mark my post as SOLVED if it has resolved your problem. It helps others with similar situations.

ASA 5505 ISP Failover (PPPoE/DHCP)

Hello,
I have 2 WAN uplinks:
The primary is VDSL (PPPoE) - very fast, and I have a static IP + /29 subnet 'assigned' to me.
The secondary is DSL (DHCP) - slower
What I'm trying to do is setup ISP failover on my ASA 5505 with security plus licence... and the way I have it currently setup 'half-works'. If the primary goes down - the primary route is removed from the routing table and the secondary route is 'inserted'. I have the NATs setup so I have internet access and all seems well. The problem however is when the primary ISP comes online again, the ASA doesn't switch back over. It maintains the backup route until I manually switch it (by temporarily disabling the backup ISP switch port).
This is what I did to configure it:
config t
sla monitor 10
type echo protocol ipicmpecho x.x.x.x interface outside-primary
frequency 5
exit
sla monitor schedule 10 life forever start-time now
track 1 rtr 10 reachability
route outside-primary 0 0 x.x.x.x 1 track 1
route outside-backup 0 0 y.y.y.y 2
nat (inside,outside-primary) after-auto source dynamic any interface
nat (inside,outside-backup) after-auto source dynamic any interface
Have I missed anything? Is there a better way to set this up? I noticed in the ADSM if you edit an interface there seems to be the ability to set tracker IDs, SLA IDs, etc - but couldn't really find anything on google that helped.
Any assistance would be greatly appreciated.
Thanks!
Robert

Hi Robert,
you need this command:
no ip verify reverse-path interface outside_primary
Problem:
SLA monitoring does not work after the ASA is upgrade to version 8.0.
Solution:
The problem is possibly be due to the IP Reverse-Path command configured in the OUTSIDE interface. Remove the command in ASA and try to check the SLA Monitoring.
For reference:
http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/70559-pix-dual-isp.html
https://supportforums.cisco.com/blog/150001
HTH
"Plz don't forget to choose correct answer and rate help full answer "

ASA 5505 PPPoE via DSL

Having trouble getting a public IP on the outside interface.
ASA 5505 running 8.0(2)
Westell E90610030-06 DSL box running current firmware.
Service provider is AT&T (Bellsouth)
DSL modem is in bridge mode.
Outside interface of 5505 is set to PPPoE with known good credentials.
I've tried CHAP and PAP authentication.
Last attempt, using MAC cloning, showed a PPPoE address of 0.0.0.0 255.255.255.255 in the client monitor in ASDM. Authentication is still set to CHAP.
I've read that AT&T does a 2-hour IP lease, so my next step is to shut down the DSL router for 2 hours and try again.
I believe PPPoE debug is still broken in this ASA version, unfortunately.
TIA

interface Ethernet0/0
nameif Outside
security-level 0
pppoe client vpdn group
ip address pppoe setroute
<--->
vpdn group request dialout pppoe
vpdn group localname
vpdn group ppp authentication chap
vpdn username password ******** store-local

Cisco ASA 5505 - problem with negotiating IP address from PPPoE

Hi all,
I have problem with negotiating IP address from PPPoE. There is following design: ISP providing vDSL ending on VDSL modem in bridge mode. Behind brigde modem is ASA 5505 terminting PPPoE on OUTSIDE. Everything works fine except negotiating IP address from PPPoE server.
I have configured ASA 5505 with (ASA Version 9.2(2)4) for PPPoE like this [1.]. But If i try to "show" IP address on OUTSIDE interface a get this [2.], ok strange but let's continue. If list "show vpdn pppinterface id 1" i get this [3.]. Seems that I got public IP addres what was right, but this IP address was not associated with interface OUTSIDE?
Well, if I set IP address manually like this [4.] and also set a default route everything works fine but what will happen when ISP change reservation for my IP address or default gateway.
I have tried different version of ASA OS like 8.4, 9.1 but without luck.
Can anybody help me. Thanks a lot.
Regards
Karel
[1.]
interface Vlan100
description >>VLAN pro pripojeni do internetu<<
nameif OUTSIDE
security-level 0
pppoe client vpdn group O2
ip address pppoe setroute
vpdn group O2 request dialout pppoe
vpdn group O2 localname O2
vpdn group O2 ppp authentication chap
vpdn username O2 password *****
interface Ethernet0/0
description >>uplink O2 vDSL<<
switchport access vlan 100
[2.]
ciscoasa(config-if)# show ip address vlan 100 pppoe
ciscoasa(config-if)# 0.0.0.0 255.255.255.255 on Interface: OUTSIDE
ciscoasa(config-if)# show interface vlan 100 detail
Interface Vlan2 "OUTSIDE", is up, line protocol is up
Hardware is EtherSVI, BW 100 Mbps, DLY 100 usec
        Description: >>VLAN pro pripojeni do internetu<<
        MAC address f44e.05d0.6c17, MTU 1492
        IP address unassigned
Traffic Statistics for "OUTSIDE":
        28 packets input, 1307 bytes
        31 packets output, 721 bytes
        0 packets dropped
      1 minute input rate 0 pkts/sec, 3 bytes/sec
      1 minute output rate 0 pkts/sec, 1 bytes/sec
      1 minute drop rate, 0 pkts/sec
      5 minute input rate 0 pkts/sec, 0 bytes/sec
      5 minute output rate 0 pkts/sec, 0 bytes/sec
      5 minute drop rate, 0 pkts/sec
Control Point Interface States:
        Interface number is 15
        Interface config status is active
        Interface state is active
[3.]
ciscoasa(config-if)# show vpdn pppinterface id 1
PPP virtual interface id = 1
PPP authentication protocol is CHAP
Server ip address is 88.103.200.41
Our ip address is 85.71.188.158
Transmitted Pkts: 20, Received Pkts: 16, Error Pkts: 0
MPPE key strength is None
MPPE_Encrypt_Pkts: 0, MPPE_Encrypt_Bytes: 0
MPPE_Decrypt_Pkts: 0, MPPE_Decrypt_Bytes: 0
Rcvd_Out_Of_Seq_MPPE_Pkts: 0
ciscoasa(config-if)# show vpdn session state
%No active L2TP tunnels
%No active PPTP tunnels
PPPoE Session Information (Total tunnels=1 sessions=1)
SessID TunID Intf     State       Last Chg
22298      2 OUTSIDE SESSION_UP 561 secs
[4.]
interface Vlan100
description >>VLAN pro pripojeni do internetu<<
nameif OUTSIDE
security-level 0
pppoe client vpdn group O2
ip address 85.71.188.158 255.255.255.255 pppoe setroute
route OUTSIDE 0.0.0.0 0.0.0.0 88.103.200.41 1

You're right that the ACL should not affect otherwise allowed communications to the interface address.
Try disabling the ip audit feature on your outside interface.
no ip audit interface OUTSIDE AP_OUTSIDE_INFO
no ip audit interface OUTSIDE AP_OUTSIDE_ATTACK

Cisco ASA 5505 - 2 PPPoE connection

Hi,
Please I would be very pleased if someone could give me a hand in this matter.
I have a Cisco ASA 5505 9.0(2), 2 dial-up connection (ADSL) with fix IP from the same ISP. I have 2 Linksys router (each dial-up has a router) as well. Both Linksys are connected directly to ASA configured in bridge mode.
I set up one dial-up on interface called “outside” with PPPoE configuration which is, in fact, up and running. I’m able to get my fix public IP.
My problem come from when I try to set up the second dial-up on interface called “outside-other”. I configure properly all PPPoE parameters however I’m not able to get my second fix public IP. Somehow, it’s not able to establish a connection with the ISP. (PPPoE session has not been established yet)
This could be useful information: the PPPoE Username is the same in both dial-up connection (given by my ISP).
I hope someone can shed light on this issue.
Thanks in advance,
Apologies for my lack of awareness.
Antonio

Hi,
This is my schema:
connection A ( interface outside) --> DSL --> Router Linksys mode bridge --> Cisco ASA , up and running with IP fix.
connection B ( interface outside-other) --> DSL --> Router Linksys mode bridge --> Cisco ASA, down : Status PADR_SENT
I tried to use two different VPDN_groups for the two connections A and B. However, B is still not working. Just one of them is able to get IP from ISP, connection A.
When I set up the Linksys router (connection B) in PPPoE, the connection works and get an IP fix from ISP.
What I want to do is set up a VPN on connection B so I need to configure this second dial-up on Cisco ASA. I cannot use connection A due to security reasons.
Thanks

How to connect my BBZ10 to a PPPoE wireless internet?

Hi,
I have an ADSL PPPoE wireless internet connection to which I'm not able to connect my BB Z10? My internet provider says I cannot connect mobiles to PPPoE dial up connection? Also I tried to connect to my cousin's hotspot which I could not not establish a connection to? Kindly advice......

hamza_fth wrote:
Hi,
I have an ADSL PPPoE wireless internet connection to which I'm not able to connect my BB Z10? My internet provider says I cannot connect mobiles to PPPoE dial up connection? Also I tried to connect to my cousin's hotspot which I could not not establish a connection to? Kindly advice......
I have an ADSL PPPoE wireless internet connection, should be 'I have a ADSL PPPoE WAN internet connection' with
wireless.
You can't connect direct to the dialup connection but you can connect any device via WiFi.
Does the router have small aerial(s) and is wireless enabled on the router ?.
If you don't know, to check you will need the IP address of the router, username and password is usually 'admin'.
I think there is a problem with the Z10 if it can't connect to other wireless hotspots.

Application Error - Faulting module name: KERNELBASE.dll, version: 6.1.7600.16385

Hi,
we have one Visual C++ application and this application also using few external dlls. while exiting from application, getting following error. This
is happened in Windows 7.
Please help us to resolve this issue.
Log Name:
Application
Source:
Application Error
Date:
28/07/2010 11:44:16 AM
Event ID:
1000
Task Category: (100)
Level:
Error
Keywords:
Classic
User:
N/A
Computer:
CRIWKS12.crillylaw.local
Description:
Faulting application name: WinTest.exe, version: 2.7.1.0, time stamp: 0x4b78d5b8
Faulting module name: KERNELBASE.dll, version: 6.1.7600.16385, time stamp: 0x4a5bdaae
Exception code: 0x0eedfade
Fault offset: 0x00009617
Faulting process id: 0x10b8
Faulting application start time: 0x01cb2df647dfd847
Faulting application path: C:\Program Files\xxx\xxx\xxx\ WinTest.exe
Faulting module path: C:\Windows\system32\KERNELBASE.dll
Report Id: a17377fd-99e9-11df-8941-90fba60d7539
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Application Error" />
<EventID Qualifiers="0">1000</EventID>
<Level>2</Level>
<Task>100</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2010-07-28T01:44:16.000000000Z" />
<EventRecordID>3773</EventRecordID>
<Channel>Application</Channel>
<Computer>CRIWKS12.crillylaw.local</Computer>
<Security />
</System>
<EventData>
<Data> WinTest.exe</Data>
<Data>2.7.1.0</Data>
<Data>4b78d5b8</Data>
<Data>KERNELBASE.dll</Data>
<Data>6.1.7600.16385</Data>
<Data>4a5bdaae</Data>
<Data>0eedfade</Data>
<Data>00009617</Data>
<Data>10b8</Data>
<Data>01cb2df647dfd847</Data>
<Data>C:\Program Files\xxx\xxx\xxx\ WinTest.exe</Data>
<Data>C:\Windows\system32\KERNELBASE.dll</Data>
<Data>a17377fd-99e9-11df-8941-90fba60d7539</Data>
</EventData>
</Event>
PS. I apologise for not being able to provide the application's name.

Hi Jesse ,
I am pasting the entire module where the code fails:
/// <summary>
/// Pool the job execution status
/// </summary>
private void PoolJobExecutionStatus()
int waitIndex = 0;
while (true)
try
lock (this.lockingObject)
this.ReOpenRegistryConnection();
currentJob = SR.Job.Load(this.currentJobId, this.poolingConnection);
JobStatusEventArgs jobStatusArg = (currentJob.Status == SR.JobStatus.Aborted) ?
new JobStatusEventArgs(currentJob.Name, currentJob.Status, currentJob.ErrorMessage) :
new JobStatusEventArgs(currentJob.Name, currentJob.Status);
this.dispatcher.BeginInvoke(new EventHandler<JobStatusEventArgs>(RaiseUpdateStatus), DispatcherPriority.Normal, new object[] { this, jobStatusArg });
if (currentJob.Status == JobStatus.Aborted || currentJob.Status == JobStatus.Completed)
this.PoolJobThread.Abort();
break;
catch (ThreadAbortException)
catch (ConnectionFailure ex)
TridentErrorHandler.HandleUIException(ex);
// If reconnection fails more than the max reconnection value then exit.
if (this.connectionAttempts >= this.maxConnectionAttempts)
break;
this.connectionAttempts++;
catch (BackendStorageException ex)
TridentErrorHandler.HandleUIException(ex);
// If reconnection fails 5 times then exit.
if (this.connectionAttempts >= this.maxConnectionAttempts)
break;
this.connectionAttempts++;
catch (Exception ex)
TridentErrorHandler.HandleUIException(ex);
break;
try
Thread.Sleep(500);
// If job is in waiting state, every 3 min show the user retry message.
// (waitIndex == 360) Specifes 3 min.
if (currentJob.Status == JobStatus.Waiting && waitIndex == 360)
waitIndex = 0;
JobStatusEventArgs jobStatusArg = new JobStatusEventArgs(this.currentJob.Name, this.currentJob.Status, TridentResourceManager.GetString("JobTerminatedByUserMessage"));
this.dispatcher.BeginInvoke(new EventHandler<JobStatusEventArgs>(RaiseUpdateStatus), DispatcherPriority.Normal, new object[] { this, jobStatusArg });
catch (Exception ex)
TridentErrorHandler.HandleUIException(ex);
waitIndex++;
public void StartDataProductService(Guid jobId, Connection poolConnection)
this.currentJobId = jobId;
this.poolingConnection = poolConnection;
this.ClearTempData();
this.HaltService();
this.PoolJobThread = new Thread(this.PoolJobExecutionStatus);
this.PoolJobThread.Start();
Hope this helps
Regards,
Rahul

I am constantly receiving an error message that says "Could not find a PPPoE Server." My wireless internet connection seems to working fine, I'm not having any issues. How do I get rid of this error message?

A few weeks ago my computer had lost the connection to the wireless internet. I set it up again and was able to connect to the internet, however since then I've been receiving an error message "Could not find a PPPoE Server." I went back into Preferences and unchecked the PPPoE server option but the error message still pops up.
Any idea how to fix it?

In the Network pane of System Prefences, do you have duplicate services on the left column? When you "set it up again", you might have duplicated a service and both (the good working one and the previous that lost connection) might be trying to connect at the same time.

PPPoE on 7600

Similar Messages

Maybe you are looking for