Pre Requisites for Implementing the CUE

Hi,
I have an  IP Telephony set up with CME in 2 different branches.We need to implemet the AA in sites.
What are the pre requisites for hardware and license based  that need to check before implementing the CUE.
one site having cisco 2911 router with Version 15.2(2)T3 and with interface ISM module is present which would like to configure for the AA.
second site having 2901 with Version 15.0(1r)M16 and  with interface Embedded-Service-Engine0/0.
Attached is the Show tech support for each CME's .
Thanks in advance
Nithin Louis.

Hello
if there is no module installed you can completely ignore Embedded-Services-Engine as it won't be doing anything. Embedded Service Engine
Overview:-
Cisco Integrated Services Routers Generation 2 (Cisco ISRs G2) have dual  core CPUs on the motherboard. The first core runs Cisco IOS software as  Cisco Integrated Services Routers (ISRs) do; the second core, or the Embedded Service Engine, is capable of running Linux-based applications.
The following Cisco ISR G2 platforms support the Embedded Service Engine:
•Cisco 2911
•Cisco 2921
•Cisco 2951
•Cisco 3925
•Cisco 3945
Note:- As above 2901 not support embedded service engine . May be you got it on the CLI , because you run the same S/W version.Reference 
https://supportforums.cisco.com/discussion/11184226/interface-embedded-service-engine00
*That is why i did not mention for Embededd service engine module supportedwith Cisco 2901, so kindly check. The above post Cisco document for compatibality.If you need to try , so try with minumum memory 1G as 2911
Memory required for 2911,2921 is 1G , 2951 is 1.5 G , 39XX is 2.5 G.My advise to you to go through  ISM-SRE-300-K9 , and shut Embedded service engine .
Thanks
please rate all useful information

Similar Messages

  • What are the pre requisites for implementing ChaRM

    Hi
    We are planning to implement ChaRM & CTS+ in our organization. We are using three system landscape and we have EP, PI, BI and ECC systems.
    Can you please tell me what are the pre requisites for implementing ChaRM & CTS+ and what are the areas i need to look before starting the configuration
    Thanks & Regards
    Anand

    The listed pre-requisites for the implementation of ChaRM are;
    1.  Already completed the basic configuraiton of SAP Solution Manager
    2.  You have set-up your solution, landscape and installed base (iBase) for the systems to be integrated
    3.  you have setup business partners for the users (or at least 1)
    4.  satellite systems are at the minimum  support package level required (note 907768)
    5.  connections are available to the satelite systems
    6.  CTS+ if you wish to control non ABAP change requests through ChaRM

  • Pre-requisites for implementing WMS for an Existing Organization.

    Dear Folks,
       My client is planning to implement WMS for an Existing Organization.And this organization(warehouse) performs all the daily transactions.
    Are there any pre-requisites to be done before implementing WMS on this organization?
    Any help is  highly appreciated.
    Regards,
    Sri

    >
    venkatesan janardhanam wrote:
    > Hi Experts
    >
    > We are planning to implement charm & cts+ in our company. We are having 3 system landscape and we have ep, bi & ecc systems. 
    >
    > I want to know how much space and RAM will require for implementing this and please tell me what the Pre requisites for implementing ChaRM & CTS+.
    >
    > Thanks in advance
    >
    > Thanks & Regards
    Hello Venkatesan,
    There isnt a T-Shirt sizing available for a Solution Manager system per scenario usage. You will have to use the sizing tool available on the url : http://service.sap.com/solutionmanager --> Check the section Starting with EHP1 and under the planning section you would find the sizing tool.
    Once this tool is downloaded you can then add the scenarios that you would like to use and plan your system accordingly.
    Regards
    Amit

  • Pre requisites for implementing ChaRM & CTS+

    Hi Experts
    We are planning to implement charm & cts+ in our company. We are having 3 system landscape and we have ep, bi & ecc systems. 
    I want to know how much space and RAM will require for implementing this and please tell me what the Pre requisites for implementing ChaRM & CTS+.
    Thanks in advance
    Thanks & Regards

    >
    venkatesan janardhanam wrote:
    > Hi Experts
    >
    > We are planning to implement charm & cts+ in our company. We are having 3 system landscape and we have ep, bi & ecc systems. 
    >
    > I want to know how much space and RAM will require for implementing this and please tell me what the Pre requisites for implementing ChaRM & CTS+.
    >
    > Thanks in advance
    >
    > Thanks & Regards
    Hello Venkatesan,
    There isnt a T-Shirt sizing available for a Solution Manager system per scenario usage. You will have to use the sizing tool available on the url : http://service.sap.com/solutionmanager --> Check the section Starting with EHP1 and under the planning section you would find the sizing tool.
    Once this tool is downloaded you can then add the scenarios that you would like to use and plan your system accordingly.
    Regards
    Amit

  • Pre-Requisites for Implementing E Recruiting on ECC6.0

    Hi All,
    Can anyone please tell me what are the pre-requisites that are to be met to implement E-Recruitment on ECC6.0 (No EHP).
    And where can i find out the differences of Erecruitment on ECC6.0 and EHP6 (Functionalities that will be missed if we go without EHP6).
    Also is EP necessary to implement E recruitment. We even do not have ESS / MSS
    Our System is a Plane ECC (No EHP).
    Regards
    Syed

    Hello Ameen,
    Well ECC6.0 is R/3 Server and EHP6 is Portal server .
    E-recruitment works good with portal. It provides so may functionalities there .
    If u don't have EHP or don't want to use it .
    In that case u can Create Customized module pool  Application , but obviously u will not get feel and look and some other functionalities available over portal .
    You can create Role Matrix table, where u can save roles of Recruiter, manager and id password etc etc .
    Plus SAP has also provided traditional Recruitment in R/3 system, you can also use that . You can find that in SPRO .
    From EHP4 Sap moved on to Webdynpro abap  which was BSP till EHP3 , SO you can also use Webdynpro applications directly without portal . But there you need to customize more  . OR you can have Customised Webdynpro application for Recruitment also .
    Regards,
    Pran

  • Pre-requisites for using the Ajax in Portal

    Hi ,
    we are using the SAP Portal 7.01 on level SP 7. What is the prerequisite for using the Ajax frame work in sap portal. Is my current version which we are using is sufficient or need to upgrade to some other version. If the current version is sufficient to use the Ajax frame work, provide the steps for configuring the Ajax.
    Please reply to this
    Thanks

    Hi,
    Now regarding the activation of AFP, you have the do the following steps:
    - System Administration - > Portal Display -> Desktop & Display Rules
    - Open the rule collection from Master Rule Collection
    - Add IF expression with suitable user/group .
    - From the content catalog, navigate to portal content -> every user -> Standard portal users ->
      defaultAjaxFrameworkContent -> Ajax portal Desktop and add this to THEN expression.
    - Apply & Save.
    Now you will be able to use the AFP on your portal.
    Hope it is useful.
    Regards,
    Nishant Singh

  • E-recruiting : Pre-requisite for using the report HRALXSYNC

    what data must be present for an EMPLOYEE in order to use this report.
    Regards,
    Bharat

    Hello Bharat,
    running HRALXSYNC requires not much data for the employee. IT 0000, 0001, 0002 and 0105 subtype 0010 should be maintained. These infotypes are usually maintained after hiring action.
    More important to successfully run the report is setting up the full integration of e-recruiting to HR. This has shown much more difficult and much more effort on the systems I had to do it.
    Best regards
    Roman Weise

  • Is the Profit Center a pre-requisite for activating the New GL?

    We are currently using the Classic General Ledger in the ECC 6.0 and looking into activating the New General Ledger. However, we are not using the Profit Center. Can anyone help me if we can activate the new General Ledger without activating the Profit Center?
    Thanks

    Nope - that is incorrect information - there are many benefits to new GL. However turning on new GL and not using PC are not connected to each other. PC is activated in case if you genuinely feel the need to report Profits/revenues across a PC.

  • What are the pre requisites for E-Recruitment module?

    Hi all,
    What are the pre requisites for implementing E-Recruitment module ?
    Does it require Hr module or as stand alone it can work?
    Regards.
    Rajendra

    Thanks Aniket
    Will the following configuration work as e-recruitment stand alone mode.
    WAS with ABAP stack + E-Recruting 6.0 sp + Java stack + Portal + ESS MSS Business package ( for e recruiting).
    Regards
    Rajendra

  • What are the pre-requisite for ABAP Proxy communication?

    What are the pre-requisite for ABAP Proxy communication?

    hi,
    How to create proxy.
    http://help.sap.com/saphelp_nw04/helpdata/en/14/555f3c482a7331e10000000a114084/frameset.htm
    How to Activate Proxy.
    /people/vijaya.kumari2/blog/2006/01/26/how-do-you-activate-abap-proxies
    ABAP Server Proxies (Inbound Proxy)
    /people/siva.maranani/blog/2005/04/03/abap-server-proxies
    OutBound Proxy (Client Proxy)
    /people/sravya.talanki2/blog/2006/07/28/smarter-approach-for-coding-abap-proxies
    /people/ravikumar.allampallam/blog/2005/03/14/abap-proxies-in-xiclient-proxy
    File to R/3 via ABAP Proxy with good example
    /people/prateek.shah/blog/2005/06/14/file-to-r3-via-abap-proxy
    Debug your inbound ABAP Proxy implementation
    /people/stefan.grube/blog/2006/07/28/xi-debug-your-inbound-abap-proxy-implementation
    http://help.sap.com/saphelp_nw2004s/helpdata/en/48/d5a1fe5f317a4e8e35801ed2c88246/frameset.htm
    Synchronous Proxies:
    Outbound Synchronous Proxy
    https://www.sdn.sap.com/irj/sdn/wiki?path=/display/profile/abap%2bproxy%2boutbound%2bprogram%2b-%2bpurchase%2border%2bsend
    Inbound Synchronous Proxy
    https://www.sdn.sap.com/irj/sdn/wiki?path=/display/profile/abap%2bproxy%2binbound%2bprogram%2b-%2bsales%2border%2bcreation
    regards
    srinivasreddy

  • What are the pre requisites for SPLIT VALUATION OF A MATERIALS

    Dear friends
    What are the pre requisites for creating SPLIT VALUATION for  A MATERIAL in particular Plant
    regards
    Radha

    Hi,
    I am not sure what you mean exactly.
    But you would need to have the valuation category and all of the valuation types created in config in advance.
    Then you can allocate the appropriate valuation category to the material (accounting view) (as long as no stock or open POs etc. exist).
    then you can create your additional accounting views (one for each valuation type that you want to use).
    Steve B

  • What are the pre-requisites for learning OA Framework?

    Hi,
    Im new to oaf,can any body help on this
    What are the pre-requisites for learning OA Framework?
    Karthik

    In order to develop any OAF Application you need to know few concepts before doing any kind of development. The concepts are basically the Business Components for Java(BC4J) components.
    They are:
    Application Module(AM)
    Entity Object(EO)
    View Object(VO)
    Association Object(AO)
    View Link(VL)
    Now let us see the description of each component.
    Application Module:
    Application Modules serve as a containers for related BC4J components. The pages are related by participating in the same task. It also defines the logical data model and business methods needed.They provide the transaction context and also used for establishing database connection. AM’s can be nested to provide more complex AM’s.
    Entity Object:
    EO encapsulates the business logic and rules.EO’s are used for Inserting,Updating and Deleting data. This is used for validating across the applications. We can also link to other EO’s and create a Association object.
    View Object:
    View object encapsulates the database query. It is used for selecting data. It provides iteration over a query result set.VO’s are primarily based on Eo’s. It can be used on multiple EO’s if the UI is for update. It provides a single point of contact for getting and setting entity object values. It can be linked together to form View Links.
    Association Object:
    An association object is created where we link EO’s. For example take the search page where we link the same EO to form a association between the manager and employee. Every employee should have a manager associated. But if it President then no there is no manager associated. This is a perfect example to understand the AO.
    View Link:
    A view link is an active link between view links. A view link can be created by providing the source and destination views and source and destination attributes. There are two modes of View link operation that can be performed. A document and Master/Detail operation.
    -----Let me know if you need more information
    Regards
    Meher Irk
    Edited by: Meher Irk on Oct 23, 2010 10:45 AM

  • What are the pre requisites for SAP SRM7.0  DB Rrefresh?

    Hi,
    What are the pre requisites for SRM DB Rrefresh?
    Thanks

    Hello Peter,
    When it comes to DB refresh you need to know what all the client dependent data which needs to be retained.
    For example you need  RFC connections, Variants, User master etc.
    As a pre task of Database refresh you may need to export the tables which are related to this so that once the database is refreshed you need to import them.
    Ensure the proper backup of production database is available. Also check all the STMS configurations which need to be retained again.
    Make sure that you need to have enough disk space which can accommodate your production data in to the pre production system.
    These are some of the general consideration one needs to have but again it depends on the environment on which one runs SAP systems.
    Regards
    Vivek

  • What are the pre-requisite for JAVA Proxy communication?

    What are the pre-requisite for JAVA Proxy communication?

    Hi,
    You can install the Java proxy runtime on the SAP J2EE Engine Release 6.40 SP5 or higher.
    The messaging system that the Java proxy runtime uses to send messages to the Integration Server must also be installed on the J2EE server.
    To send messages from a J2EE application, the application must be programmed against beans that encapsulate all details about the Java runtime. The following classes are generated:
    ·        Proxy classes that send or receive messages using the Java proxy runtime.
    ·        Bean classes as an outer shell that conform to the J2EE standard. The beans call the proxy classes for communication.
    The classes must be deployed on the J2EE server together with their J2EE application
    see this link for the example scenario http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/f272165e-0401-0010-b4a1-e7eb8903501d

  • ADFS2012R2 Install: Why does this need Active Directory Domain Admin Account as one of the pre requisites for installating AD FS server

    Team,
    We were trying to configure AD FS through ADFS Wizard on Windows 2012 R2 box as part of ADFS upgrade from ADFS 2.0 to ADFS 3.0. But the installation got stuck in between as the domain account which we were using does not have admin privileges on the AD side. 
    We have to raise to AD team to elevate the rights of the service accountb we are using.
    Can any one please tell me why having an admin AD account is pre requisite for the AD FS configuration, what are the "Write" changes which occur at Active Directory side post ADFS installtion, we need this details to supply to AD team for the justification
    purpose.
    Would appreciate any detailed response on this query
    thanks
    Lav

    Hi,
    dont know all exact objects ADFS is trying to create in AD, but it needs to create some container and objects under cn=Programm Data,DC=domain,dc=com for sharing certificates.
    We had troube with this because the container does'nt exists.
    Regards
    Peter
    Peter Stapf - ExpertCircle GmbH - My blog:
    JustIDM.wordpress.com

Maybe you are looking for