Premier Elements 9 and Canon HV20

Hi
Just installed a copy of Premier elements 9 onto a new laptop and when I capture footage in HD 1080i the captured footage is pixalated with green pixals.  When I import using same cable and port in Standard def the caputed footage is fine.
Any clues as to what I am doing wrong/
Many thanks
Graham
Morecambe
Lancashire

Just for grins I tried to capture directly from the HV20 into PrE instead of going through HDVSplit.  Capture worked without issue so I don't think there is a compatability problem between the camcorder and PrE.  NOTE: my HV20 is NTSC and not PAL.
You may want to attempt to capture from the camcorder without a tape to further isolate the issue.  This can be done by putting the camcorder in camera mode and simply capturing the footage.  If this works and the tape capture does not then there is an issue with tape playback.  If the non-tape and tape capture don't work then you either have an issue with the camera or the setup/hardware on your computer.  It would be worth while to try to connect the camcorder to another computer.

Similar Messages

  • I am trying to update Photoshop & Premier Elements 11 and get this Error Code: U43M1D207

    I am trying to update both Photoshop & Premier Elements 11 and get this Error Code: U43M1D207.
    Can anyone help ?

    Try downloading the updates manually from http://www.adobe.com/downloads/updates/
    Thanks
    Nikhil

  • I am trying to import a video into Premier Elements 11 and keep getting an error message

    I'm trying to import a video into Premier Elements 11 and keep getting an error message but it doesn't say what the error is.

    This is the Photoshop Elements forum. You want the Premiere  Elements forum:
    Premiere Elements

  • I have always used Nero wav editor to add eq, add volume and noralize recordings....do I have that feature in premier elements? and if so, where do I find it?

    I have always used Nero wav editor to add eq, add volume and noralize recordings....do I have that feature in premier elements? and if so, where do I find it?

    Zillenwater said: You can export a FLIP video clip using Picasa 3, and then bring it into Premiere Elements. The video and audio will successfully come in.
    Thanks much - this worked very well and was so easy. After spending hours looking at a lot of different converters and getting nowhere, I spotted this solution.
    I used Flip avi files directly from the camera, copied them into a folder that Picasa 3 could find, and then exported them. They showed up in my /My Documents/My Pictures/Picasa/Exported Videos folder as Windows Media Files (.wmv). I brought my test files into Premiere Pro 1.5, previewed them, placed them in the timeline and rendered them. they looked good here, so I exported my movie and the video looks pretty good, considering it was from the Flip.
    Picasa did something that a dozen other conversion programs couldn't get right (or at least I couldn't find the right combination of codecs and settings). It's a relief, alright, and information I'm happy to share.

  • Installed new Premier Elements 12 and dymamiclinkmanager has stopped working

    The Sw does not start at all I get several error messages:
    Installed new Premier Elements 12 and dymamiclinkmanager has stopped working
    Problem signature:
      Problem Event Name:    APPCRASH
      Application Name:    dynamiclinkmanager.exe
      Application Version:    6.0.0.0
      Application Timestamp:    523cc6d3
      Fault Module Name:    MSVCR100.dll
      Fault Module Version:    10.0.40219.1
      Fault Module Timestamp:    4d5f0c22
      Exception Code:    40000015
      Exception Offset:    0008d6fd
      OS Version:    6.3.9600.2.0.0.256.48
      Locale ID:    1035
    and after those a Message:
    Adobe Premier Elements 12 has stopped working
    Problem signature:
      Problem Event Name:    APPCRASH
      Application Name:    Adobe Premiere Elements.exe
      Application Version:    12.0.0.0
      Application Timestamp:    523cd4d5
      Fault Module Name:    dvamarshal.dll
      Fault Module Version:    11.0.0.0
      Fault Module Timestamp:    523cc62d
      Exception Code:    c0000005
      Exception Offset:    0000000000034961
      OS Version:    6.3.9600.2.0.0.256.48
      Locale ID:    1035
    So did I purchase piece of crap, or what should I do to get the SW working?
    Br
    -H

    First, note that this is a user-to-user forum. If you want to contact Adobe, you'll need to call or write them on their main site.
    That said, as the note says at the top of the forum, you're going to have to provide us a lot more information if you want us to help you. "Stopped working" doesn't tell us much. Does this mean that it was working in the past but then stopped? What stopped? What did it do that it's not doing now? What were you doing when it stopped? Was it when you were adding video to your project, for instance?
    What operating system are you using? If Windows, have you manually gone to Windows Update and made sure you've got the non-critical updates, which don't download automatically to your system? Have you ensured you have the latest version of Quicktime, per the program's requirements?
    How fast is your processor, how much RAM do you have and how much free, clean, defragmented space is on your hard drive?
    What model of camcorder is your video coming from and what format and resolution is it? Did you use Premiere Elements to get the video from your camcorder to your Premiere Elements project?

  • I have Premier Elements 12 and recently changed my computer to an iMac. I want to re-register my software on the iMac but the Adobe system won't let me. Anyone have an answer? Cheers Brian

    I have Premier Elements 12 and recently changed my computer to an iMac. I want to re-register my software on the iMac but the Adobe system won't let me. Anyone have an answer? Cheers Brian

    Brian Chapple
    I did not see your post 4 until after I had posted just now.
    That is one of the drawbacks related to purchasing Premiere Elements as a download from Adobe...the download is specific to the Windows or Mac operating system to which it is downloaded. So all you have purchased that way are the installation files and a serial number for Premiere Elements 12 Windows. If you had purchased Premiere Elements 12 in the box packaging, that comes with a disc for Windows and a disc for Mac.
    How long ago did you purchase Premiere Elements 12 Windows? If within 30 days of purchase, you can look into a 30 day money back from Adobe. But you cannot purchase the box packaging from Adobe. It only offers the download purchase from it. You would have to buy from an authorized reseller if you wanted the boxed purchase.
    The way it is now, you will need to purchase new installation files and serial number for Premiere Elements 12 for your iMac.
    That is the situation that I believe exists. More information if needed.
    ATR

  • Final Cut Studio 2 and Canon hv20

    I'm currently working on Final Cut Studio 2 and I'm looking at buying a Canon HV20. I've looked into some threads on this one and it seems that people are having trouble with this camera on FC Studio 2. Is there anyone out there that can attest to smooth and efficient workflow with this set up? A major selling point for me is the 24p, tell me it works well, please tell me it works well.
    thank you,
    t r e y v o n

    HV20 works perfectly at 24p in FCP 6.0.2.
    Added advantage is that you can capture uncompressed (with HDMI card and fast drive/RAID) at much higher quality and resolution than HDV.
    Quality is so good, you can create great 1920 x 1080 24p green screen shots (using 4:2:2 color space from HDMI) and dvMatte Pro 3.
    The next step up to get better quality at 24p is around $5K-$6K range (I think?).
    Here's a small image of a 24p frame shot on green screen with the HV20:
    http://www.ecophones.com/embed/printplace.jpg

  • Which firewire cable for new MacBook Pro and Canon HV20?

    I just bought a new MacBook Pro and want to transfer video from my Canon HV20 camcorder (using FinalCut Express). The Canon instructions say to use a "DV cable" and I've learned that the MacBook Pro only has an "800 fire wire" port. Can someone give me the exact type of cable that I should get (even my local Apple Store couldn't help me).
    Thanks!

    I'm surprised that the folks at the Apple Store couldn't guide you. You just need a firewire cable with the proper fw400 connector on one end and a fw800 connector on the other. Here's one source for both cables and adapters:
    http://www.pccables.com/cgi-bin/orders6.cgi?id=ID7468267&rsite=google.comsearc&r code=&action=Cat&search=FIREWIRE

  • Live capture with FCE 4 and Canon HV20 - End of Tape when capture in HD

    I have a Canon HV20 HiDef video camera that was given to me to record an event. I want to try and avoid using the tapes if possible and capture the video directly into my MacBook Pro using FCE 4.
    If I try and capture video when the camera is set to HD output, the capture screen comes up, I can see the image from the camera on the FCE4 screen for a split second, then I get a message indicating the end of tape has been encountered. (The tape isn't even being used and is no where near the end anyway).
    If I change the camera to DV output, I can change the FCE4 Easy Setup to simple DV control and it works fine to capture live, except that it is no longer in HD. I get no error message about the tape end being hit.
    I am unable to find any Easy Setup configuration that will allow me to record live. Any suggestions?
    Thanks.

    Play your tape forward to a position where there is continuous Timecode and try again.
    As Ian suggests the correct _AIC Easy Setup_ is the only way to get HDV in to your Mac via FCE.
    Note: Your camera must be set to output HDV assuming it recorded HDV.
    Al

  • Adobe Premier Elements 11 and Mac OS 10.9

    Yesterday I downloaded from Apple Apps Store Adobe Premier Elements 11 to my iMac OS 10.9 The process has gone untill "loading exporter quicktime host bundle" and nothing more
    What shall I do?

    franko2014
    It would appear the issue is not isolated.
    http://feedback.photoshop.com/photoshop_family/topics/premiere_elements_not_loading_with_m avericks?page=1
    http://feedback.photoshop.com/photoshop_family/topics/photoshop_elements_11_failing_on_ima c_after_upgrading_to_os_x_mavericks
    http://feedback.photoshop.com/photoshop_family/topics/premiere_elements_not_loading_with_m avericks
    I am in no position to know just how much support you can get from Adobe since Premiere Elements 11 is no longer the current version on these Mac Store purchased products.
    You could try Adobe Chat and see how far you can get. The following link typically proves helpful for that purpose.
    http://helpx.adobe.com/contact.html?product=premiere-elements&topic=using-my-product-or-se rvice
    When the link opens, click on "I still need help" to bring up the Adobe Chat pop up.
    Let us know the outcome.
    Thanks.
    ATR

  • Elements 11 and Canon CR2 Compatability

    Will Elements 11 open Canon CR2 files or Will I still need to convert to DNG?

    Each camera is supported specifically, so it depends on the model of the camera, how new it is, compared to the version of the camera-raw plug-in that PSE11 is using.  If the camera is newer than the plug-in then it won’t be supported because Adobe didn’t have a chance to profile ti before the plug-in was created.
    You can update your PSE11 to the latest compatible version with Help / Updates in the Editor module.
    If your camera is a 70D then it will be supported with ACR 8.2 plug-in version (use help/about plugsin/camera raw to determine the version) but because PSE12 comes out in a few days/weeks, as does ACR 8.2, then perhaps PSE11 will not be updated to ACR 8.2 and you’d need to buy PSE12.
    What camera model are the CR2 files from and what version of the ACR plug-in are you using?
    Here is a web-page at Adobe that lists the version of ACR (and other programs) for each model of camera they support raw files from:
    http://helpx.adobe.com/creative-suite/kb/camera-raw-plug-supported-cameras.html

  • Premier Elements 8 and Windows Media Output

    Hello,
    I recently bought a new computer (Win 7 64 bit) to replace my old PC (Vista 32 Bit).  On my old PC I had Premier Elements 7, but got Premier Elements 8 for the new PC.  I like to create Windows Media files as output so I can watch the videos from my XBox 360.  But I noticed that the output from PE8 takes takes up much less of the screen than the output from PE7.  In other words, when I play the WMV file (on either my computer or the XBox), there is a large black border around the video.  When running a WMV file from PE7, the video takes up the entire screen area.
    As an experiment, I imported about a 10 second clip from my video camera.  I then created a video in WMV from both PCs using the exact same settings (HD 1080i 30 - I went to the advanced settings and made sure every setting was the same).  And the results were consistent.  The video from PE7 took up the entire screen (in Windows Media Player), while the PE8 output had a significant border around it (I tried playing each file on both PCs and got the same results).
    It's much nicer when watching the videos on my HD TV from the XBox if the videos take up the entire screen rather than taking up a much smaller portion of the screen.  Any ideas on how to get the output the same would be appreciated.  Thanks!

    I unchecked the setting on the clip and it resolved the issue!  I found the setting under Edit, Preferences, General, Default Scale to Frame Size (no longer the last setting).  It looks like for existing projects I'll have to go and set this on a clip by clip basis (which some have a ton of individual clips).  Hopefully on new projects it will import it correctly.
    Thanks for the answers!

  • Photoshop Elements 8 and Canon Powershot G15.

    I have Photoshop Elements 8 and a Canon Powershot G15.  I need to download Raw from this camera, which appears to be impossible, although it will download from my Nikon D60.  Do I need a plug in to achieve the result with the Powershot; if so what will it cost and how do I get it?  Thanks,
    brucem

    Hi,
    The G15 is supported in Camera Raw 7.3 (or later) which, unfortunately, is not compatible with Photoshop Elements 8.
    You can either upgrade to Photoshop Elements 11 (or later) or download and install the free Adobe DNG converter. You copy your CR2 to a folder and then give the DNG converter that folder name. The converter will then convert those files to the DNG format. the DNG files can then be used by Photoshop Elements 8.
    DNG  Converter 8.7
    Mac – http://www.adobe.com/support/downloads/detail.jsp?ftpID=5858
    Win – http://www.adobe.com/support/downloads/detail.jsp?ftpID=5864
    Useful Tutorial
    http://www.youtube.com/watch?v=0bqGovpuihw
    Brian

  • Photoshop elements 13 and canon protoprinter pro driver

    I installed elements 13 to my computer and my automation tools such as canon photoprinter pro printer are no longer visible.  Yje driver still exsists for my photoshop elements 12 and prints without a problem. I reinstalled the canon drivers without and chnage to photoshop elements 13.
    There must be an issue with elements 13.1.  Any ideas?

    sillysully511 wrote:
    Thank you.  Right now I have Elements 11 and wanted to make sure if I purchased 13 it would work and I guess it does
    You can always download the trial version before paying for it.  Use it for 30 days and then buy the boxed version to activate your trial product.  You only need to insert the serial number to activate the trial version if you decide to buy the boxed version.

  • Photoshop elements 7 and canon powershot g12 - not compatible?

    Hello everyone,
    I'm trying to open the .cr2 files off my canon powershot g12 in elements 7. I know that the RAW update would be found in CAMERARAW 6.3 which is only for elements 9 and have installed the lastest compatible (5.4) on my system. Is there any way for me to open my files or will I have to upgrade or even switch to a different programme?
    Thanks for your help!

    I don't know if the language version has anything to do with it, but DNG isn't as universal as it was promoted as being and it's not always backwards compatible. You might try some of the different settings in the DNG converter prefs and see if they make any difference.

Maybe you are looking for