Premiere elements 3 rendering problem

Every time I place a shot into the timeline, the thin red render line appears and I need to render the shot, even though I haven't done anything to the shot like grading it or changing it in any way. Now my hard drive is full with all of the rendered shots and I've run out of drive space. I thought premiere only needed to render a shot if it had been changed in some way. Any help would be appreciated.
thanks

What format are your video clips, if they are anything other than DV-AVI (type 2) or HDV then the clip will require rendering.
You can delete these temporary render files from one of the options at the top of the editing window... cant recall which one off hand. This will clear your harddrive and then you can render to clear the red line over the timeline for smooth playback.

Similar Messages

Adobe Premiere Elements 4 - Rendering Problem

If I create small slide shows in Photoshop Elements 6 (ranging from 59 - 125 JPEG Still Shots with captions and/or added text)I can then send each slide show separately into Premiere Elements 4, make further adjustments and add title pages, I can then render and save as a project.
If I take several of these slide shows as a block and send them to Premiere Elements 4, I get a Premiere Elements window stating "Adobe Premiere Elements is running very low on system memory, please save your project and proceed with caution". So I click OK and save. I then go to render, after 2-4% rendering I get a video Preview Error window with various warnings including, "Out of Memory - Unknown Error" or "Disc write error:- verify drive connections, available disc space and disc access privileges. Then save close and relaunch project".
If I open a slide show project in Premiere Elements 4 and try to add a second slide show to it via the get media button - in the Add Media window I get Look in 4.0 and five folders appear (no icons for projects) I can then look in files of type and there is no listing for .prel files so tried "all files" and the icons for the slide shows appear. I then select a second slide show to add to the first and click open. I now get an Add Media Failure window which gives file addresses and the error reads "File format not supported/ one of the necessary components may not have been installed".
I have run the installation disc again to repair any installation errors but to no avail.
My computer is an Intel core 2 duo 3.16 GHz on an Asus P5Q P45M M/board with Gigabyte GF9600GT Graphics card.750GB HDD & 4GB Ram.
Hope somebody can help.
Bob Smith.

Most likely your photos are too large. We recommend using no larger than photos no larger than 1000x750 pixels in size. (The actual file size of the JPEGs has nothing to do with this, since JPEGs can be highly compressed.
http://www.adobeforums.com/webx/.3bb8822c
Resize your photos and you'll see a huge boost in performance.

Have to re install elements 11 & premiere elements 11. cause problem with upgrade windows 8.0 to 8.1

have to re install elements 11 & premiere elements 11. cause: problem with upgrade windows 8.0 to 8.1. Lost all software and data.
how to re install elements11. (downloads purchased in your store 2013-05)
[email protected]

have to re install elements 11 & premiere elements 11. cause: problem with upgrade windows 8.0 to 8.1. Lost all software and data.
how to re install elements11. (downloads purchased in your store 2013-05)
[email protected]

Premiere Elements 12 output problem

I am having problems outputting my project. Different errors messages. One says transcoding error. Another time it says export error. Other times it crashes. And then the program won't even open.
Any suggestions?
bwatson9

Steve,
First, thank you for your prompt response. This is the first time I have used Premiere Elements 12. I don't seem to have a manual for the software.
The product was bought with my new computer. I am using windows 8.1 (64-bit) with Intel Core i7-4770 CPU @ 3.40GHz. I have 12 GB of installed RAM. I have 1TB hard drive of which this is the first project I done.
I have checked to make sure that I am getting all Windows and Microsoft Updates. I even manually went to Windows Update and installed the optional updates.
The project is a 20 min. video using mostly photos and 2 small video clips. The project is saved in its own folder.
When I go to the timeline in Expert view I do see an orange-yellow line above the timeline. It runs the whole length of the project.
I understand from reading the FAQ's that each photo cannot be larger than 1000 x 750 pixels. I will check that and reduce their size. Is there anything else that I need to do?
Where can I find a manual?
Thanks,
bwatson9
Date: Sun, 23 Mar 2014 06:31:03 -0700
From: [email protected]
To: [email protected]
Subject: Premiere Elements 12 output problem
    Re: Premiere Elements 12 output problem
    created by Steve Grisetti in Premiere Elements - View the full discussion
A lot depends on a lot.
What operating system are you using? What processor do you have and how much RAM and how much free space is on your hard drive?
How long is your project? What model of camcorder is your video coming from and what format and resolution is it?
Have you ensured that your project file is saved to its own folder, with no other project files in this folder?
When you add your video to your timeline in Expert view, do you see a yellow-orange line above the clips, along the top of the timeline? This indicates a mismatch between project settings and video specs.
If you are on a Windows computer, have you set up your computer to get both Windows and Microsoft Updates -- and have you manually gone to Windows Update and ensured you have even the optional updates that don't install automatically?
When did you last run Disk Cleanup and Disk Defragmenter?
     Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/6234402#6234402
     Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/6234402#6234402
     To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/6234402#6234402. In the Actions box on the right, click the Stop Email Notifications link.
           Start a new discussion in Premiere Elements at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

Premiere Elements 9 technical problem - please help

Hello,
I have very serious problem with my Premiere Elements 9 for Mac.
This program is turning off over and over again.
I have started to prepare my new project and during the playback oraz during the operations on texts Premiere turns off very often.
It wasn't huge problem for me because I was using save very often but the main problem is that now I can not create any DVD nor export this project to any video file because during the encoding process Premiere is turning off again (usually between 65-95% of the process of encoding)
I tried to open this project on my PC with Windows with Premiere Elements 7 but 7 shows this file is not compatibile with previous version. So I installed ver. 9 on Windows (I bought Mac/Windows) and again Premiere Elements 9 for Windows has shown that my mac file is not compatibile??
I was trying to find any bug fix files on Internet but I haven't found.
Can anybody help me? It's 4 pm here and I need to burn my dvds invitation of my son's birthday for tomorrow and I have stucked.
Here are some additional information:
Adobe Premiere Elements 9 Mac/Windows edition (seperate installing dvds) - legally purchased
Latest MacOs - orignal
No external codecs
No illigal programms
Only legal software
I will appreciate you help.
Kind regards,
Tom
p.s. I use Premiere Elements for few years so I know what to do or wat to click to export file or create DVD

Ha!!!
I found the source of problem
I mentioned that my problems have started when I had added text so I removed all text made by Elements text tool (I noticed that after rendering these object was still with red line instead of green).
So now everything is ok so I'll prepare all texts as a psd transparent files and it will be great
So it is Adobe's error - I hope they will prepare some fix for it.
Anyway, thank you guys for help and support.
I hope I'll finish my project this night because two unsleeping nights are to much for me
Take care,
Tom

Premiere Elements 12: Rendering not on the exact frames

I'm using Premiere Elements 12 and cutting MOV files in most cases.
Now I detected that PE isn't rendering always correctly: In some cases the rendered file shows at the end of a clip 1 more frame than in it shows in the cutting window.
Meaning: The original MOV clip contains 2 scenes. I import the MOV file into my PE12 project and put it into the cutting window.
Then I'm moving the viewing bar of the cutting window exactly to the end of scene 1 and click "cut".
When I separate both scenes in the cutting window, PE12 show exactly the result I want to get: scene 1 ends with the last frame of scene 1, scene 2 starts with the first frame of scene 2.
Then I delete scene 2 and render scene 1 to a MP4 file.
When viewing the result file in any player (e.g. Windows Medie Player, VLC, Quicktime), all these players show at the end of scene 1 the first frame of the original scene 2.
Again: even if I couldn't see this first frame of scene 2 in the cutting window!
So the cutting window doesn't show EXACTLY the result I will get!
I already tries different ways of importing the original MOV files, different codecs and so on - nothing helped.
In roughly 50% the cuts of the final file are like planned, the other 50% of cuts show one frame too much at the end of a scene.
Problem: In a lot of cases the scenes are already very short, so I can't give always "one frame plus" before I cut: sometimes I really need every single frame.
And I can't believe that a programm like Premiere Elements should not be able to cut exactly at the frame where it is supposed to!
So does anyone have a clou what I'm doing wrong?
Or this this a knows issue of PE?
Thanks in advance!

Dear ATR,
I now found some time to check this out.
Let me describe exactly what I'm doing:
Source file is a MOV file full HD.
Drag & drop it onto the timeline.
Set half frame option (is it called "field"?) to "reduce flickering" - because if I don't (default option: "none"), the rendered result is not that stable, meaning the picture is totterling a little. Is this normal? Could this setting cause the trouble with the last frame at cutting/rendering?
Switched Timeline to frame display instead of timecode.
By the way: this CTRL + clicking the area above the Timeline doesn't work ...
Moved the Timeline bar with the arrow keys to the position where I want to cut; the Monitor Window above the Timeline showed the first frame of scene 2. Doublechecked by moving the cursor with the arrow keys one frame forward and back again to really got the right position (twice). Clicked "cut" icon on Timeline.
Repeated the same at the end of scene 2 - the Monitor showed the first frame of scene 3.
Moved scene 2 to another position on the Timeline with the mouse (drag & drop).
Checked cuts on the timeline: scene 2 showed the first and last frame as it should.
Repeated all this with 10 scenes from the original MOV file, brought all of them into a new position and thus order.
Deleted the rest of the original MOV file from the timeline.
Put the 10 scenes together, placed them at the left side of the Timeline.
Rendered the result.
Settings: AVCHD - MP4
PAL, 1920 x 1080 px, 30 fps, Widescreen 16:9, Profile: High, Level: 5.0
rendern with max depth: "no"
VBR, 2-path
target: 15 mbps
max: 25 mbps
Audio; AAC, stereo, 48 Khz, Quality: high, 160 kbps
Priority: Bitrate
The result file showes on 4 of 10 scenes that one frame too much at the end of the cut scene.
And it always happens at the same scenes, not randomly!
So it does not depend if I'm viewing frames or timecode in the Timeline. Surprise!
But what I detected: When I'm using a "new project", this issue does not occur!!!
So I looked at the project settings: The "new project" I let the default settings be, because it I should import a file and drag this to the Timeline, the software would give me a message if the project settings should not match.
Default settings are: NTSC-ADCHD-AVCHD 1080p60.
But what I normally do is using a template file with all my intro, outro, audio, logo and so on, copy that *.prel file where I want to edit it, rename it and then open this copied prel file. Here I the project settings show:
HD 1080i, 25 fps, 1920 x 1080 (I guess I once selected this under PAL because there is no PAL 1080p25 oder 30, just 1080p50). And I'm from Germany, so I chose PAL instead of NTSC ...
So I guess this makes a difference - even if I do not have a clue, why.
Big question now: How can I chance my project settings in my template file without making it anew?
Because I cannot copy all the objects from one project to another, right? At least I never managed to do so...
To built the template anew would take about 6 hours, and on this basic template are based 6 more templates for special formats. So makeing all templates anew would cost me up to 2-3 days!!!
So I really hope for a better solution
Kind regards,
Lutz

Adobe Premiere Elements 11 Effects Problem - HELP

I use Adobe Premiere Elements 11, and when I use effects the footage ends up speeding up, repeating itself, and just not staying the same as it originally was. Does this have to do with what type of footage it is. I am using screen-captures that I got when using Bandicam. If anyone could help me with this problem, it would be greatly appriciated, thanks.

Gamerwalk,
One option would be to convert your odd AVI-MPEG file to DV-AVI, which is what PrE loves most. This FAQ Entry will give you some tips on doing that: http://forums.adobe.com/thread/415317?tstart=0
I use an older file conversion program, DigitalMedia Converter 2.7, but it is NOT freeware. Also, Deskshare, the publisher, has released newer versions.
Good luck,
Hunt

Adobe premiere elements 11 rendering at lower bit rate than i select

Hi, I'm using Adobe Premiere Elements 11, 64-bit Windows.
I keep trying to render a project at a bit target bit rate of 10.05 MB/S (.h264 1080p MP4) but the resulting .mp4 file keeps coming out with an average bit rate of around 7000kb instead of 10,000kb...
The source files used in the project are 17mbs..
Other projects are rendering fine.
Would be very grateful for some advice.
Edit: Now realised it's happening to a substantial fraction of my projects. I am being very careful to select the right render settings

Sminty
Please confirm
Premiere Elements 11
a. Export as
Publish+Share
Computer
AVCHD
with presets = MP4 H.264 1920 x 1080p30
and, under the Advanced Button/Video Tab of the preset, what are your setting for Maximum Bitrate to go along with the 10.5 Mbps Target Bitrate (the units there are Mbps or Mb/second which is megabits per second).
b. I believe that each encode needs to be looked at separately.
One example...Original AVCHD.mov file, 1920 x 1080p29.97, 69.9 MB, 12.579 seconds, and Bitrate Overall 46.6 Mbps and Bitrate 45 Mbps.
I decided that i would try for an AVCHD.mp4 export whose properties read out would include bitrate 10.5 Mbps.
I selected Publish+Share/Computer/AVCHD with Presets = MP4 H.264 1920 x 1080p30, and, in the Advanced Settings set Bitrate as VBR 2 Pass
Target 10.5 Mbps and Maximum 15 Mbps.
The result was an AVCHD.mp4 1920 x 1080p30 file with a Bitrate Overall 10.8 and Bitrate 10.6 Mbps.
Second example..Original AVCHD.mov file from another camera, 1920 x 1080p30, 24.0 MB, 14.14 seconds, and Bitrate Overall 14.4 Mbps and Bitrate 12.2.
I selected Publish+Share/Computer/AVCHD with Presets = MP4 H.264 1920 x 1080p30, and, in the Advanced Settings set Bitrate as VBR 2 Pass
Target 5 Mbps and Maximum 10 Mbps.
The result was an AVCHD.mp4 1920 x 1080p30 with a Bitrate Overall 5.17 Mbps and Bitrate 5.006.
Please review and consider.
Thank you.
ATR

Premiere elements trial download problems

I seem to have downloaded adobe premiere elements 10 but I can't extract it? I keep getting this "invalid checksum" pop-up.

If the download is completed in the Adobe Download Assistant you can temporarily turn off the feature to verify the checksum. The following steps will allow you to temporarily disable this feature:
Open the Disk Utility located in Applications/Utilities
Go under the Disk Utility menu and select preferences
Deselect the option to verify checksums
Try mounting your DMG file
I would recommend turning this feature back on though after the installation is complete. Also if you notice this happening on additional files it can indicate a problem with your Internet connection.

Adobe Premiere elements 12 publishing problem.

After making a video in Adobe Premiere Elements 12, I decided to publish it to my computer. However, once it finished rendering it only came out as an audio. The visual video didn't show at all. It played as if it were a song. How can I fix this?

Sparkles3216
If your videos worked with Premiere Elements 10, then they should work with Premiere Elements 12.
From what I have read in this thread, your source seems to be files in amv video format (proprietary) which seem to have relations to MotionJPEG video compression and .avi file extension. Challenging, but. What is the actual file extension of your amv files?
AMV - MultimediaWiki
If you can post a sample of one of these videos that are going into your Premiere Elements 12 project and losing sound in the export from Premiere Elements 12, I would be glad for the opportunity to check it out for you in various versions of Premiere Elements, including 10 and 12. You might send the sample in a Dropbox link posted in your thread reply.
My only requirement is the assurance that you have permission to work with these videos. YouTube license does not allow for downloads of its videos. A person can create a YouTube account, sign into YouTube, can upload a video, and later download his or her own, but not the video of others without permission.
I still do not see the support for the file in Premiere Elements (any version). But if you say that the file worked in Premiere Elements 10, as I said, it should work in Premiere Elements 12.
More later.
Thanks.
ATR

Uploading using Adobe Premiere Elements 12 Network problems

Hi,
Is there a place in Adobe Premiere Elements 12 that we can insert our company proxy details, the reason being. When I go to Publish and Share and click "Social Websites" and want to upload a video to youtube and push next it gives the following error "Online Services encountered an error. The services will be terminated or paused if possible."
If I use a 3G card it allows us to upload. Our network must be blocking this link or programme, yet we have made sure from our side adobe is not blocked on the network and I have access to all websites.
My question is can we insert proxy details somewhere or can I get the link of where that link is taking us to when pushing next trying to upload with youtube via adobe . I know it is going to youtube but I need the exact URL to make sure we allow this link to work.
Anyone have the answer for me?

MaudeSt
This is not Adobe. Rather user to user. For network problems when using the current version which is now Premiere Elements 12, please contact Adobe via its Adobe Chat.
Click on the following link, and then find and click on Chat Panel to discuss
Premiere Elements
Downloading, Installing, Setting Up
Downloading, Installing
Chat Panel
Contact Customer Care
I have set the web page to the Chat Panel level. If it does not hold the setting, then you will need to navigate to Adobe Chat using the topics
above as guidelines. If you end up seeing only Ask the Community instead of Chat Panel, then try again later. Chat has been having in times
when it is unavailable due to updating. It is an on and off situation lately. Chat has the option to do remote control of your computer for
troubleshooting purposes. We do not.
At the moment that I am hitting the "Add Reply" for this post, only Ask the Community option is being displayed at the Adobe Chat contact link.
Please let us know the outcome.
Thank you.
ATR

Re: Premiere Elements 8 NVidia problem

I can't work with windows seven 64 bits with this new version.
After few seconds run time error VC++ when i insert video and accept improve mode
Crash without message in effect module
I don't know if the problem comme from seven RC version or Premiere Elements 8.

Heron62 wrote:
Crash without message in effect module
This sounds like the nVidia driver problem many of us have had (there are around half-a-dozen threads about this).
If you have an nVidia graphics card and are running nVidia driver 190.62 then remove (and do not reinstall) the PhysX / Steroscopic3D features from Add/Remove Programs in Control Panel.
Who knows - this may also fix the VC++ problem. If it does, please let us know as it extends the forums knowledge of this nVidia bug.
Cheers,
Neale
Insanity is hereditary, you get it from your children

Premiere Elements 9.0 problem uploading Project

Premiere Elements 9.0 will not fully upload a Project. It uploads to 100% and then stalls. Just prior to this problem it gave me a lack of memory and proceed with caution notice. Solutions?

hodgson
Basically, what are you uploading your project to?
Your Premiere Elements question should be posted in the Adobe Premiere Elements Forum (video editing) rather than in the Adobe Photoshop Elements Forum (photo editing). A moderator should be along shortly to move your thread there.
In the meanwhile I will ask the following
1. On what computer operating system are you running Premiere Elements 9 and are you running Premiere Elements as the 9.0.1 Update?
2. When you talk about uploading a project, exactly where are you in the project....Share/Online/YouTube or some place else?
3. What are the properties of what you have on the Timeline? And, what have you set as the project preset based on the properties of those source media? What is the total duration of your Timeline content?
4. Please describe your computer resources: 32 or 64 bit system, installed and available RAM, free hard drive space?
The properties of your source is important since their format may be a factor in the low memory messages.
Looking forward to your follow up in the Adobe Premiere Elements Forum.
Thanks.
ATR

Abobe Premiere Elements 12 Rendering Issue

After clicking "Render" button, the program runs about a few seconds and stop. Meanwhile, a error message pops up, asking to copy and paste the provided serial number on the given adobe website to get decode. When you do it, the website shows another error message which says something like that the website dose not support any adobe premiere elements below the version 8. This doesn't make any sense at all! We need the answers to this issue, please.

premiere elements 12
Assuming Premiere Elements 12 on Windows 7, 8, or 8.1 64 bit for now....
On what computer operating system is your Premiere Elements 12 running on? Have you updated 12 to the 12.1 Update yet? If not, please do so from an opened new project's Help Menu/Update. Is your computer connected to the Internet?
In some cases, I have seen where Premiere Elements will need to do a one time activation of a feature. Rendering may be the feature in your case.
There have been several reports from users of Premiere Elements 8 and earlier about messages for MPEG2 activation that cannot be done because Adobe no longer supports MPEG2 Activation for Premiere Elements 8 and earlier. But, you have version 12.
What I would suggest is
1. Uninstall the program the usual Control Panel way
2. Do a free ccleaner run through
CCleaner - Download
3. Reinstall the program with the antivirus and firewall(s) disabled....be sure of the integrity of your Internet connection.
You could try before the above the deletion of the Adobe Premiere Elements Prefs file or the whole 12.0 Folder in which the Adobe Premiere Elements Prefs file exists.
Local Disk C
Users
Owner
AppData
Roaming
Adobe
Premiere Elements
12.0
and in the 12.0 Folder is the Adobe Premiere Elements Prefs file that you delete. If that does not work, then delete the whole 12.0 Folder in which the Adobe Premiere Elements Prefs file exists. Be sure to be working with Folder Option Show Hidden Files, Folders, and Drives active so that you can see the complete path cited.
Please review and consider and then we will plan further troubleshooting strategy accordingly.
Thank you.
ATR

Premiere Elements 4.0 Probleme beim Exportieren

Hallo liebe Profis,
nun habe ich es endlich geschafft, das Hochzeitsvideo zu schneiden und einen richtig tollen (meinen ersten) Film mit Menü, Kapitel usw. daraus zu machen.
Die Länge des Films beträgt ca. 01:48:00 Stunden.
Ich bin mit Windows XP, Premiere Elements 4.0, einer großen externen 300 GB Festplatte, von der lediglich 40 GB belegt sind und einem Arbeitsspeicher von 1024 MB ausgestattet.
So, nun möchte ich natürlich das Video exportieren und ich dachte erst einmal auf die externe Festplatte, denn ich weiß nicht, wie groß der Film am Ende sein wird und welche DVD ich dafür brauche. Das wäre dann irgendwann mal eine andere Frage.
Das Problem:
Ich kann den Film nicht exportieren. Die Fehlermeldung ist Nicht genügend Speicherplatz auf Laufwerk zum Erstellen von temporären Dateien für den Brennvorgang
Ich exportiere so: Ich geh auf den Reiter Verteilen, dann Datenträger, wähle Ordner 4,7 GB oder auch 8,5 GB, habe beides probiert, dann die Ordnerposition (mein externes Laufwerk), PAL_Widescreen_DolbyDVD und bei der Qualität habe ich schon alles durchprobiert. Die beste wäre natürlich toll, auch bei der niedersten klappt es nicht.
Ich wäre Euch dankbar für Hilfe, ein paar Tipps, Anregungen, Hinweise oder was Euch so einfällt, denn ich weiß erst einmal überhaupt nicht weiter. Die Mühe soll ja auch nicht umsonst gewesen sein....
Bei google und den Foren habe ich mein Problem bisher nicht gefunden. Auch über einen Link, in dem dieses Thema bereits besprochen wurde, würde ich mich sehr freuen.
Danke schon jetzt!
Derya

Hallo Achim,
da du anscheinend häufiger größere Projekte bearbeitest, kannst du mir sicher auch eine Meldung erklären, die mich bei der Neuanlage von Projekten in Premiere Pro CS3 permanent nervt:
Wenn ich versuche Videoclips von meiner Datenpartition zu öffnen, so taucht diese, im Gegensatz zu der Partition mit dem Betriebssystem und den Programmen, nicht in der Liste der Laufwerke auf.
Und zudem erscheint das rotierende bunte Etwas (Mac OS) und schließlich nach einer Ewigkeit die Meldung:
Verbindung fehlgeschlagen. Möglicherweise ist der Server nicht vorhanden oder zurzeit nicht in Betrieb ...
Ich vermute, dass dies eventuell mit den Voreinstellungen - Arbeitslaufwerken zu tun haben könnte. Habe in der Hilfe nachgelesen jedoch keinebefreidigende Antwort dort gefunden.
Gibt es da eine Auflösung? Danke schon mal für einen Tip
Herbert

Premiere elements 3 rendering problem

Similar Messages

Maybe you are looking for