Premiere Pro CS5 firewire out

Just downloaded the trial and noticed that the firewire out is still not working alongside with the program monitor. I couldn't even half the time get the video to preview via firewire. It's like the signal kept going in and out. Now I brought an AVCHD clip in and can tell it scrubs much better. However I'm dissapointed that someone can't watch their timeline in the program monitor and firewire out at the sam time like it has been for years. Anyone else experiencing this too?

Not to swing this completely off topic...but am I the only person who uses DVI out to preview on a separate monitor? As of CS4 it's available and works without error, so far as my personal usage indicates.
I know some folks want to use IEEE 1394 out, but with the delay issues and seemingly constant headaches with Adobe support/non-support of this workflow, why not just use an available DVI port (if you have one) and run to a DVI or VGA capable monitor (or run DVI > HDMI, just as well)....?
I ditched my IEEE 1394 preview method as of CS4 because there are less parts involved and the preview is perfectly good for my non-major-motion picture work. I don't need the audio signal out to the same device (I have a somewhat more refined audio monitoring solution) so the DVI/VGA/HDMI solution works fine for me.
Just asking....anyone else?

Similar Messages

Premiere Pro CS5 runs out of memory

I have the same problem with Premiere running out of memory loading a project with lots of images in it. Running task manager, you can see it eat memory at 250MB per second until it pegs the meter after a short time and then things start failing. The CS4 version does not have this problem and opens the project without error.

What are the pixel x pixel dimensions of those still images? If they are overly-large, there is a very heavy load, when working with that Project. For Scaling them to fit the Sequence Frame Size, with automation in PS, see this ARTICLE.
If one's computer is already on the borderline for resources, overly-large stills can shove it over the brink. There are few reasons to use overly-large images, as one can only ever see the pixels in the Sequence's Frame Size. The only reason for using images larger than that Frame Size are to Pan on Zoomed out images, with Effect>Motion>Position.
Good luck,
Hunt

Exsternal harddrive drops out, when using adobe premiere pro cs5. Cant load projects. any one had this problem or the answer to it?

I have two WD external hard drives that i keep all my video files, music and adobe premiere pro cs5 projects on. Up until 2 days ago they were working perfect, now they drop out when i try and load my projects from them, or watch a movie from them. tried restoring from two weeks ago and nothing changed. I get that error msg when i try and load something. The error msg is the one that comes up when you disconnect a usb drive without ejecting it correct. I don't think its the drives as i only use one most the time, and the other just sits there not connected, but that are now having the same issues. Help me plaza

yea i am using the right sequence
here are 4 screen shots of 2 different things i was editing, both used to record my xbox 360 with Hauppauge, Seems adobe is the only program playing the video file with the audio out of sync/mixed up
[URL=http://imageshack.us/photo/my-images/803/screenshotlrh.png/][IMG]http://img803.imageshack.us/img803/1669/screenshotlrh.png[/IMG][/URL]
[URL=http://imageshack.us/photo/my-images/826/screenshot2yv.png/][IMG]http://img826.imageshack.us/img826/3012/screenshot2yv.png[/IMG][/URL]
[URL=http://imageshack.us/photo/my-images/841/screenshot3aa.png/][IMG]http://img841.imageshack.us/img841/7042/screenshot3aa.png[/IMG][/URL]
[URL=http://imageshack.us/photo/my-images/5/screenshot4on.png/][IMG]http://img5.imageshack.us/img5/6096/screenshot4on.png[/IMG][/URL]
The Yellow Devil May Cry video is the video with the audio problem,
The metal gear rising video is red because of the pic above it, and the sound works ok on that, infact that video is finished and uploaded to youtube now.

Premiere Pro CS5.0.4 -Will not play any video- reinstall didn't help

here's my system info -
Model: MacPro5,1, BootROM MP51.007F.B03, 4 processors, Quad-Core Intel Xeon, 3.2 GHz, 16 GB, SMC 1.39f11
Graphics: ATI Radeon HD 5870, ATI Radeon HD 5870, PCIe, 1024 MB
   ----------------I only use one monitor, 1920x1200, 32bit color depth
   ------------------No Capture Card, No Sound Card or I/O box
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8E), Broadcom BCM43xx 1.0
Bluetooth: Version 2.4.5f3, 2 service, 19 devices, 1 incoming serial ports
Serial ATA Device: HL-DT-ST DVD-RW GH61N
Serial ATA Device: TSSTcorp CDDVDW SH-222AL
Serial ATA Device: Hitachi HDS722020ALA330, 1.82 TB
---------- This 2tb Hitachi is my data drive - there are 600GB free (33%)
Serial ATA Device: OWC Mercury Extreme Pro SSD, 223.57 GB
   ---------This 250gb SSD drive is my system/application drive - 120GB free (50%)
Serial ATA Device: OWC Mercury Extreme Pro SSD, 111.79 GB
------------this 125GB SSD I use as a project-specific drive to serve up video very quickly when i'm generating Video material using the software VDMX
USB Device: Keyboard Hub, 0x05ac (Apple Inc.), 0x1006, 0xfd300000 / 2
USB Device: Apple Keyboard, 0x05ac (Apple Inc.), 0x0220, 0xfd320000 / 3
USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x5a100000 / 2
USB Device: Bluetooth USB Host Controller, 0x05ac (Apple Inc.), 0x8215, 0x5a110000 / 3
FireWire Device: built-in_hub, Up to 800 Mb/sec
i've been using Premiere Pro for about a year and a half with no trouble, no crashes that i can remember.   I updated to 5.0.4 when it came out and experienced no problems.
I have not made any changes to my system (drivers, programs, etc.) since the last time i worked with Premiere Pro with no trouble. The only difference is that i generated approx. 52GB of new video files (mov. uncompressed 32bit 640x480 resolution) that i was beginning to edit in to a music video.
My current problem is:: there is absolutely no playback of video in 5.0.4.   not in the tiny project window preview, not in the source preview, and not in the timeline/canvas window.   when i push PLAY, the button turns into a square STOP button, but nothing happens.   this is independent of project or file type. The project i was working on when playback stopped is using uncompressed 640x480 32bit Quicktime files and one 44khz/16bit .AIFF file.   as a quick doublecheck, I just added a 640x480 Apple Intermediate Codec file and it also will not play back.   I opened older projects and none of them will playback.
My problem started while i was working on a project. I was working on the project for probably an hour and a half with no trouble. Then it seemed to get a bit sluggish and i could hear the HD churning a little more.   After rendering out a short section (just under 10 seconds), PPro did not play back the just rendered (now greenline) section. Immediate playback of rendered material was the default behavior, and this was the first time ever that the just rendered section did not play back.   I then discovered that no video would play back at all--in any of the windows.   I can scrub through all the video without any trouble--all the frames are there.
I shut down PPro, & restarted. No change.   I restarted my computer. No change.
Realizing that the problem was likely related to a lack of space on my data drive, i deleted approx. 500GB of files off my 2 TB drive, leaving just under a 1/3 of it free. i checked the drive for errors, and defragmented it. Premiere Pro still wouldn't play any file from any project.
The files are fine, they will playback anywhere else (several different file types involved in different projects). The files are compatible with Premiere Pro (uncompressed VGA resolution Quicktime .mov), i was editing on the timeline with them for hours before all video playback stopped.   All other Adobe programs (After Effects, Photoshop work fine).
I tried to find an answer/solution on these forums, unsuccessfully.   After uninstalling PPro and reinstall (did not help), and entire Suite uninstall, Adobe Clean, and reinstall, neither version 5.0.0 or 5.0.4 will play video --the no playback problem has persisted.
I was running out of HD space --i had less room than i thought -- down to about 7% of free space, a bone-headed move on my part. I'm not surprised that playback performance got compromised due to lack of space.   But i'm shocked that the problem is persisting.   Fortunately, i had just backed up my entire system the day before. (i've backed up many times before and this never affected PPro performance)
i tried to "CLEAN" the media cache for the sequence but it had no effect (in searching the forums, i saw somebody else have their 'crashing Premiere Pro' problem solved by hitting this button). I just took a look in the user/application support/adobe/common/5.0 to look at the "Media Cache" folder and the "Media Cache Files" folder.   Neither of them are empty, even after hitting the CLEAN cache button in the main preferences 'Media' settings window.   I don't know if this is the correct behavior or not.   (i'd expect a "clean" command to empty the folder, but i'm not the programmer)
This does not appear to be the ATI/5.0 problem that so many Mac users suffered (i was lucky to never have that problem).    Again, i've never had any problems with Premiere Pro over the last year and a half, until working on this latest project with the Hard Drive very low on space.   I'm 99.9% positive that's at the heart of the issue.
I don't understand why a clean reinstall did not help in this regard. The problem is clearly PPro specific.   I found one topic in the forum where someone else experienced this same "no video playback" problem, but there was never follow-up from the user saying whether or not his problem was solved (or what was done to correct the problem).
I'd love to get some help--- seems to be a very rare issue, but right now, i can do no video editing. btw, i started a new project as well and imported a .mov file -- same problem, no video playback.
the weird thing is that i can actually still edit video. i just rearranged my timeline assets and rendered out a minute-long quicktime (Apple Intermediate Codec) .mov and it looks and plays as it should.    This is really weird. I'm baffled -- there must be some way to fix this.   I don't want to have to go back to Final Cut, certainly not when i've already paid for Create Suite 5 Production Premium and EVERYTHING works except for video playback in PrPro.
thanks in advance for your help
Message was edited by: magneticjak
Message was edited by: magneticjak

hello.   hey, thanks very much for writing back. i got some good info with a search or two. (info about what regedit is and what corresponds to it in OS X -- regedit allows you to edit "preference" keys for individual programs, OSX's equivalent for these keys are the .plists in User & System: Preferences and Application Support)
what i ended up doing was uninstalling Premiere Pro (not the suite, just PPro).   Then i deleted a few preference files:
from User /Preferences/Adobe:
com.adobe.AdobePremierePro.plist
com.Adobe.Premiere Pro.5.0.plist
and from System Preferences:
the file: Adobe Premiere Pro Prefs
and..
/.../Premiere Pro/5.0/...
AMEPrefs.xml     (i noticed that there's also a preference file in Media Encoder's own folder so i didn't sweat this one)
Debug Database.txt
Placeholder Preset.epr
PostEncodeCmds.pref
PresetCache.xml
Trace Database.txt
NOTE:
of course i don't know if deleting any files beyond the 2 .plist files in User Prefs was necessary, but... it seems to have worked.
I then reinstalled Premiere Pro CS5, and fired up an old project and i've got playback of HD and DV files, and snappy editing and rendering, so hopefully i'm good to go.   I'm just going to stick with v5.0.0 because i actually don't remember ever having any trouble with it, and i don't remember v5.0.4 adding anything i was 'missing' or 'needed'
hopefully, this thread will be useful for any future folks that run into trouble - and it's got a solution for both Windows and OS X
happy editing,
peace

Using my JVC BR-DV3000E DVR with Premiere Pro CS5

I have been testing out the use of my JVC BR-DV3000E DVR (Digital Video Recorder) using a new PC running Windows 7 (64 bit) and Premiere Pro CS5. The connection is via the firewire cable supplied with the device. It worked fine on my original PC running Windows XP with Premiere Pro 1.5.1.
When I open the capture window in CS5 it shows the message "Device Offline" at the top of the capture window and all the transport controls are greyed out. I have played around with the settings but nothing seems to overcome the problem. I am trying to capture miniDV footage in SD. Has anyone come across this problem before on either the same device or similar and has anyone any suggestion on how to fil the problem please?

Try these to see if they work
SD capture http://windv.mourek.cz/ or http://www.scenalyzer.com/main.html
I do know that the demo of Scenalyzer puts a mark in the video, so don't do anything real until you pay and enter the registration code
I don't know about the other program

Microphone Issue using Adobe Premiere Pro CS5.5

I have also posted this at the Adobe forums. I'm just hoping someone, somewhere can help.
I am a recent convert from Final Cut to Adobe Premiere Pro CS5.5, mainly so I can start burning to blu-ray. I am finding the switch a frustrating experience. The latest issue I have is with audio recording. I have an external firewire mic set up that worked flawlessly with Final Cut for two years for recording commentary tracks. Yesterday, I tried recording a commentary track in Premiere Pro, and it worked fine for about an hour, at which point it suddenly stopped. Now I can only reocrd about 6 seconds of audio before it stops recording, and repeated attempts result in a "serious error" and Premiere crashing.
I have searched everywhere and tried everything I can think of. Restarted Premiere. Uninstalled/reinstalled premiere. Shut down/unplugged/replugged in C-1 microphone. Updated software. Restarted iMac. Nothing works. I am out of things to try, and hoping someone here might have a suggestion. I have tried using the iMac's internal microphone just as a test (since the quality of the recording would be unusuable for my purposes) and Premiere won't even use that for the six seconds it will the C-1.
Thanks in advance for any advice.

So, just in case anyone else is wondering, we never did solve this issue. However, we upgraded Soundbooth to Audition, and were able to move the project there and finish the commentary track. So, that's a workaround, anyway. (A workaround that did not work in Soundbooth).

Capturing with Premiere Pro CS5 & Canon Legria HV40

Hello everyone,
I have an issue trying to capture footage from my Canon Legria HV40. My desktop operates with Windows 7 / 64bit and I use a firewire port when attempting to capture from the DV cassette on the Canon Legria HV40. After opening Premiere Pro 5 (not a trial version) I connect my camera via all the correct ports and open the capture window in the software. After setting up all my preferences for the capturing process the software recognises the camera and I am able to operate the camera from my desktop (fast forward, rewind, play etc...).
The issue starts at this point. When i press "Tape" or "Play" then "Record" to start the capturing process the camera kicks into action. However the software does not record anything from the camera.
Does anyone have any suggestions or have they come accross this issue before. Any help would be appreciated.

MKoffy Hi,
It works just fine here, same set up, but with CS5.5.2 not older version.(5.5.1 or 5.5 did not work), other contributers spoke of a "LEGACY" driver?, I think Harm Millard he may know more than I do. We are PAL, the camera obviously works, make sure you have camera set at 1920 x 1080 i.And the same setting in PP, however PP should automatcally set that for you.
In fact when Exporting to Tape it is amazing and starts the camera with out having the record button executed., it (the HV40 is Anamorphic at 1440 x 1080 (the limitation for Pro tape) and will record at Progressive, the pixels are rectangle not 1.0 , but the output is i). Do not save clips to another DRIVE.It is best in the RAID set up. according to Canon Specs it records at HDV 1080/50i , 1080/25i (PAL) These settings must match the set up in Premiere Pro 5.5.2 exactly.I do not set IN or Out points, it might have been a good thing to stripe the tape in the first place as it will recognise the Indexing numbering better that way.
I must add the quality of the Export even to Blu-ray astounded me. Nearly as good as the Canon 5D Mark II 1920 x 1080p but, that was from a CF card.
Good luck
Ps. Frankly the Premiere Pro CS5.5.2 surprised me when it recognises all that when it went to work. Because when you used Premiere Pro 1.5.1 everthing was manual, well nearly.

Premiere Pro CS5 unstable on (two) Macs - Help!

We've had Premiere Pro CS5 for a while and have tried using it a lot over the months. The problem is it's not very stable on either of out Macs so we keep going back to FCP7 for major projects.
Given Apple's recent discontinuation of support for pro video apps issues (I can't wait for FCPX to mature) and the massive transcoding delays we're currently facing in order to use FCP7 I'd really like to get Premiere Pro CS5 (5.0.3) to a place where we can use it day-in-day-out and be able to rely on it. I can accept that software occasionally crashes - but that's not where we're at. It crashes 10 times a day!
System 1:
Mac Pro - 8 core 16GB Ram, 4xSATA HDDs (1 boot 3xRAID), ATI 5770, 30" main monitor, 23" second monitor
Software installed includes Production Premium (5.0.3), Final Cut Studio (FCP7, Motion 4 etc), Lightroom 3, Aperture 3]
Snow Leopard 10.6.7 (fully updated)
System 2:
iMac 27" i7 Quad, 12GB Ram, 1 SATA drive, external Firewire Drives, ATI 5770, 24" second monitor.
Software installed includes Production Premium (5.0.3), Final Cut Studio (FCP7, Motion 4 etc)
Snow Leopard 10.6.7 (fully updated)
Just some simple stuff....
If I ever touch the handle to move a window while playing - it crashes.
Multicam crashes.
Moving clips on the sequence - sometimes crashes
Right clip and remove filters - crashes most of the time
Using the Colorista II plugin - if PPro tries to auto save a project while using the plugin - it crashes
These are just a few examples. It crashes a LOT.
So, are there any known incompatibilities between software installations? The iMac was a clean install not that long back.
Are there any known compatibility issues with these sets of hardware? If so, what? How do I fix them?
PPro also crashed when I had the older ATI card in the Mac Pro.
HELP!

> Can you point me to the change log to see what I'd lose by going back to 5.0.0 ?
Here are the details of what changed in 5.0.3 and 5.0.2.
> Do you have a ballpark idea of release time (in weeks rather an that days or hours
I'm prohibited from saying exactly---in case something goes wrong and we need to change it---but it will be very, very soon.
> I see CS5.5 trial can now run with all the codecs. If I download this
will it run side by side with 5.0.3 on my system for 30 days while I
evaluate it?
Yes, the trial version is made to run just fine on a system that has the previous version on it.

Premiere Pro CS5 Playback and Performance Issues

I upgraded (2) separate editing work stations to CS5 from CS4 about a month ago. I moved from 4 to 5 to try and get rid of some problems which both work stations were encountering.
The problems since the upgrade are similiar: playback from timeline has intermittent audio drop out and video going to black during playback, (new one)-video locked up but audio kept playing-system hung and had to be rebooted.
Also, when clicking around on the timeline or scrubbing the timeline, Premiere crashes.
This type of performance on playout or timeline usage is consistent on both machines which have indentical setups and builds. None of this happens all the time but happens enough to causes problems with workflow. We edit on the work stations, dub files to playback system for air, and use a shared server to move files back and forth as needed but files are always stored locally instead of using straight from server.
These machines are:
Premiere Pro CS5.02
OS WIndows 7 Pro 64 bit
12 GB Ram, DDR3-1333 (6-2GB modules)
CPU Intel Xeon Quad Core [email protected] GHZ, 2 processors, 8 MB Cache
500 GB SATA 2 hard drive, 7200 RPM, 32 MC (System Drive)...309 GB of space avail
(3) 1 TB SATA 2 hard drives, 7200RPM, 32 MC (3 TB, RAID0 STorage) 2.16 TB of space avail
Nvidia GE Force 9800 GT Graphics card, DUAL DVI, 1 GB
REaltek High Def Audio, Drivers 6.0.1.5953
(1) monitor in use
output of system runs to ADVC-700 breakout box to feed playback system
I have all of my software installed on C: (309 GB of 500 GB avail)
I have all of my videos files stored on D: (Raid Storage with 2.16 TB of 3 TB avail)
The only changes I've made since installing CS5 would be to change the auto save from 20 minutes to 60 minutes. Don't know if an auto save would cause an issue on playback as I've noted above.
I'm not a computer whiz by any stretch of the imagination but I can follow directions if given for testing/eval.

Do the PPBM5 Benchmark and send the results to me by PM, in addition to sending the results to Bill as indicated. I'll have a look at what might be going on here.

While importing clip getting error "The file contains too many audio channels" in premiere pro cs5

Hey,
I am using video clips from sony digital hi8 camera and trying to import video clips (.mov) 720*480 fps 29.97 .But unable to get into premiere pro cs5.System configuration:
MAC 10.6.4
2.66ghz intel core i7
4gb ram
nvidia geforce gt 330 mn.
Error :
Actually ,i have checked the inspector panel and i found same infomation in
in this panel for both clips .please check these clips screen shoots seprately .
Actually i have a long video clip and i have scatterred this clip into 6 diffrent portions
where i am not able to import the last video clip.It is giving me same error "file contain too many audio channels"".
Regards
Manoj

I too am getting this error in Premiere CS5. I was digitizing a Broadcast VHS and since I did not have a breakout box, I hooked it up to a Sony DV deck so I could connect via firewire and capture inside Premiere. I was able to capture and import 1 of the 3 clips and it did have 4 audio channels attached to it. However, upon closer inspection only 2 channels had a waveform. I captured the other 2 clips the same way, but this time, Premiere give the error "The file contains too many audio channels."
Any ideas?

Mov files in Adobe Premiere Pro CS5 - XDCAM (MPEG) resp MPEG 1/2 (xdvc)

Problem description:
I got a bunch of MOV files on a HFS+ formated disk for editing on Premiere Pro CS5 (5.0.3). When I import to Premiere, Premiere says "Codec missing or unavailable". Paragon HFS+ is used to handle the HFS+ formated disk. I copied the data to a NTFS formated disk before using.
The reseach I did give the following indications:
I did try to play in Quicktime and Quicktime told that I would need additional software to play the .mov file. But I could execute show movie inspector and it shows "XDCAM EX 1080i 50 (35Mb/s VBR)".
VLC plays (!) and tells that it is a "Mpeg 1/2 Video (xdvc)"
MediaInfo says "MPEG Video (XDCAM)"
Sound is (L)PCM according to the mov inspector programs.
The MPEG2 format seems to be supported by Premiere (also in HD), forum entries tell me I should be at version 5.0.2 as there Adobe supports the MOV container. So now my question: What am I missing?
I have no idea on the Camera used to film, but it could be a JVC, as it is told that the JVC writes mov files.

Hi Colin,
The explanation is quite simple and it appeared to me sometime during the weekend when executing completly different tasks.
The video source is different! The small clips (and your test clip) are what came from the camera and was transcoded to mov, my test clip was the edit out of FCP! It was by chance the only mov-file left, all others have been deleted after transforming to mp4, not to keep the data in double and fill up the disks with unnessecary data. So I tested this clip, which was the mistake!
Testing one of the original input files confirmed your result!
The difference between the files is having indeed 2 mono audio streams (input mov) vs one stereo stream (edit mov), all 3 obviously PCM.
Input MOV
Audio #1
ID                               : 2
Format                           : PCM
Codec ID                         : lpcm
Duration                         : 2s 760ms
Bit rate mode                    : Constant
Bit rate                         : 768 Kbps
Channel(s)                       : 1 channel
Sampling rate                    : 48.0 KHz
Bit depth                        : 16 bits
Delay relative to video          : 4h 14mn
Stream size                      : 259 KiB (2%)
Audio #2
ID                               : 3
Format                           : PCM
Codec ID                         : lpcm
Duration                         : 2s 760ms
Bit rate mode                    : Constant
Bit rate                         : 768 Kbps
Channel(s)                       : 1 channel
Sampling rate                    : 48.0 KHz
Bit depth                        : 16 bits
Delay relative to video          : 4h 14mn
Stream size                      : 259 KiB (2%)
Edit MOV:
Audio
ID                               : 2
Format                           : PCM
Format settings, Endianness      : Little
Format settings, Sign            : Signed
Codec ID                         : sowt
Duration                         : 9mn 26s
Bit rate mode                    : Constant
Bit rate                         : 1 536 Kbps
Channel(s)                       : 2 channels
Sampling rate                    : 48.0 KHz
Bit depth                        : 16 bits
Stream size                      : 104 MiB (4%)
Thanks,
Lucien.

How to work with Premiere Pro cs5.5 and After Effects cs5 together?

I have edited my movie in premiere pro cs5.5 and made the rough cut. In premiere, i have edited the video, put in soundtrack and foley. Now, i need to add muzzle flashes & blood splatters in some scenes and final color correction using After Effects cs5.
When i import the premiere project in AE and make the changes, and then i export it back as premiere project. When i open this prmiere project, it shows vaious kind of errors and no changes are retained that i did in AE. Also, when i import the premiere project (which has 4 different sequences) in AE, all the media that has been imported in the premiere project also opens in AE making it difficult to organize the media.
How should i work now so that i add vfx and color correction using AE cs5?
I thought of exporting the video from Premiere pro and then open the video in AE and add vfx to some scenes and color correction to the full video and render it out again. But, this is the first time i am using AE and i am not sure if this is the best way. PLEASE HELP.
Or, i could import the whole project in AE, add vfx, do color correction AND then export to video from AE. But i think, it will be better if i export the video from Premiere as it has loads of options to choose from while exporting to a movie.
The dynamic link does not work between Premiere Pro Cs5.5 and After Effects cs5. Even if it does, its not working on my pc.
All the footage is in HD and i want the final result in best quality HD too. PLEASE Help!

If you are working between After Effects and Premiere Pro but with versions that are not the same number, you need to just work with movies rendered and exported as intermediate, lossless files.
Dynamic Link only works between After Effects and Premiere Pro of the same version number, and only when they are installed as part of the same suite.

Premiere Pro CS5. Media Encoder .dll interace message.

Out of the blue, when I am working in Premiere Pro CS5 and want to export media, I get an error message about "this software could not find the required software interface .dll. Reinstall the software and try again..."
This just started several days ago. I have changed nothing. I did do as asked and reloaded the Adobe Premiere program and that worked for about a day. And now it is back. Also, my Premiere CS5 is starting to crash fairly often where as before it never did. I haven't changed anything on the computer. No new software added. No windows 7 updates of any kind.
Any ideas on what to do.

I experienced this at one point. Searching the WEB I saw suggestions that there was a problem with a recent version of Quicktime. (I have no idea why the quicktime player would have an impact.) However, reverting to an earlier version of Quicktime fixed the problem. Search this board using quicktime as a search phase. The quicktime web site allows you to download the earlier versions. I'm not at my editing machine, but I believe that I am at version 7.5.2.

Adobe Premiere Pro CS5 Dynamic Link not working as part of Production Premium CS5

I ran into a situation whereby I recently reinstalled my Production Premium CS 5 onto a new computer and when trying to run the Dynamic Link out of Premiere PRO CS 5 to create a new After Effects composition, After Effects tried to start up but then crashed with the error that Production Premium was needed.
Yet, I had Production Premium CS5.
(Note: The crash didn't occur when I simply tried to use Dynamic Link without anything selected in my project or timeline - but the moment I had a clip in my timeline selected to work on it, the dynamic link would not work as covered above.)
In checking around the forums I found various answers to this problem such as rebooting the computer, reformatting hard drives and/or whatever. This all may be correct.
However, as I just went through that nightmare, I was not anxious to do that again. So, I called Adobe and the following solution solved the matter in 5 minutes:
1. Close all your other Adobe applications such as After Effects.
2. Open up Premiere Pro CS5 and then deactivate it by going to HELP>DEACTIVATE and then Permanently Deactivate.
3.Close the application and restart Premiere Pro CS5.
4.Then do the same to Activate it.
5. Have your serial number handy and plug it in when prompted.
Solved it right away and worked beautifully.
Not to say there couldn't be more complicated situations, but the above worked and the simpler the better is good for me. And I thought I would post this in case anyone else ran into this problem.

Thanks for posting your solution.

What's New and Changed in Premiere Pro CS5.5 - Free Course!

Hi All,
I just wanted to point out some new video training, totally free of charge, called, "What's New and Changed in Premiere Pro CS5.5." Todd Kopriva flew all the way to Austria's "Video2Brain" studios to record these detailed tutorials and I think they're very good. Have a look gang, and see what you think!
Link: http://www.video2brain.com/en/products-117.htm#/content?t=2

Thanks, Todd, much appreciated. Such information is always welcomed by all users (at all levels), I'm sure.

Premiere Pro CS5 firewire out

Similar Messages

Maybe you are looking for