Preparing SATA drive

G'day guys
Just wondering if anyone can help, I have just purchased a 200 Gb Seagate SATA HDD and want to have it as my primary drive. It will be partitioned using Acronis partition manager and I am going to copy the contents from my current 80 Gb ATA HDD including the OS onto the 200 Gb SATA, is this ok. I still want to keep my 2 existing 80 Gb ATA drives for home videos and other assorted files and photos, backups etc. Is it fine for me to have the 2x 80 Gb HDD still in the IDE 1 slot on my mobo, with the SATA drive in the SATA port? Windows should configure this correctly won't it, it won't keep searching the ATA's for the primary partition? Do the ATA's need to be set to slave or cable select with regards to the jumpers. I will also change the existing primary part on the 80 Gb ATA to a logical partition. Is this correct?
All correspondence greatly appreciated, thankyou.
Cheers

No, it's because after you clone your drive you are going to have two identical drives that differ only in size.
SATA only and PATA only determine which drive is going to place higher in the bios internal IDE list. PATA only puts the SATA drive higher, and vice versa. You want your boot drive higher in the list.
The Keep Enabled settings keep the other type of drive enabled for use.
PS: Any time you change a setting that rearranges drives in the IDE list, on the very next boot you need to go back into the bios to set the boot drive again.

Similar Messages

Filesystem and SATA drive performance

Hi you all,
I'm in the process of installing ArchLinux for the third time on my system and I'm in need for some suggestions. The previous installations went without problems but I have realized that the system was not really tuned for some video stuff I'm working with i.e that I need support for large files on my system. Did a google and found references on xfs system that should do the trick. All went ok and I could work without problems on dv files 10-13 GB in size but suddenly I've realized the abismal low performance of my harddrive when copying files e.g: 20 min for a folder of 512 MB (indeed with multiple folders and small files)!!!. The hardware I'm using is:
AMD Athlon 2500
Gigabyte GA-7VM400AMF (VIA 8237 -sata controller)
Seagate 160 GB SATA harddrive
512 MB ram
-the "hdparm -tT /dev/sda" command gives me:
/dev/sda:
Timing cached reads: 1260 MB in 2.00 seconds = 629.77 MB/sec
Timing buffered disk reads: 152 MB in 3.01 seconds = 50.43 MB/sec
-the "sdparm /dev/sda" output is:
/dev/sda: ATA ST3160827AS 3.42
Read write error recovery mode page:
AWRE 1
ARRE 1
PER 0
Caching (SBC) mode page:
WCE 1
RCD 0
Control mode page:
SWP 0
-the "sdparm -i --verbose /dev/sda" command output is:
/dev/sda: ATA ST3160827AS 3.42
PQual=0 Device_type=0x0 RMB=0 version=0x05 [SPC-3]
[AERC=0] [TrmTsk=0] NormACA=0 HiSUP=0 Resp_data_format=2
SCCS=0 ACC=0 TGPS=0 3PC=0 Protect=0 BQue=0
EncServ=0 MultiP=0 MChngr=0 [ACKREQQ=0] Addr16=0
[RelAdr=0] WBus16=0 Sync=0 Linked=0 [TranDis=0] CmdQue=0
Device identification VPD page:
Addressed logical unit:
desig_type: vendor specific [0x0], code_set: ASCII
00 20 20 20 20 20 20 20 20 20 20 20 20 34 4d 54 30 4MT0
10 30 47 4b 48 0GKH
desig_type: T10 vendor identification, code_set: ASCII
vendor id: ATA
vendor specific: ST3160827AS 4MT00 GKH
-I have the following partitons:
Device Boot Start End Blocks Id System
/dev/sda1 * 1 3918 31471303+ c W95 FAT32 (LBA)
/dev/sda2 3919 3930 96390 83 Linux
/dev/sda3 3931 4055 1004062+ 83 Linux
/dev/sda4 4056 19457 123716565 83 Linux
sda1 partition is with winXP (still using win bootloader)
sda2 is /boot formatted as ReiserFs
sda3 is swap
sda4 is XFS formatted mounted as /
Now I'm preparing to reformat the whole drive, partitioning in the same manner but using JFS on the "/" partiton ....and this is what I would ask you guys:
1. Are the hdparm readings "normal" for my system? Please reply with some of yours if you have sata drives.
2. Please comment the sdparm readings (have no idea what could these be used for..)
3. The reallife test of copying files tells me that there should be a problem on my system -I mean that my vaio laptop with a PATA drive @4200rpm does better. If this is the case what could it be - hardware? sata_via drive (I would be willing to test a proprietary drive if it exists)? filesystem?
Thank you.

Your new drive may just be 'slower' than the old one. If they are both 7200RPM disks, it is likely that the older/smaller drive has a faster access time and/or transfer rate. This is not alwayst the case but it is possible.
Also, ensure that you have the latest nVidia nForce2 drivers installed. If you know the new drive should be 'as fast as' or 'faster than' the old drive, then check the settings that JeanGuy suggested, and if they are all set correctly, look into reverting your nVidia IDE driver to an earlier version.

T410s SATA driver install

I have a stable of T410s machines that came with XP Pro loaded. I need to install Exterprise XP Pro. Unfurtunately, once the Enterprise edition is installed, the SATA driver won't install and we're stuck in Compatability Mode.
I have the exact driver (from the NIB machine and website), and try the force-feed method (Update Driver/Don't Search/Have Disk/point to iaStor.inf in the IMSM folder [taken from the factory installation and web download of WinXP]). The machine blue screens during the install. Has anyone been able to load this driver?
Solved!
Go to Solution.

Hi bhnelson,
I'm not sure exactly what steps you followed, but i believe what could be the problem is that you never did run the install.cmd.
Try to download this driver, run to extract and it should be under "C:\DRIVERS\WIN\IRST":
http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-74431
(optionally you can download a newer version of this driver directly from Intel)
Then follow these steps (since you already got Windows XP running and compatibility mode set i guess you could start with step 9):
1. Power off the computer.
2. Power on the computer.
3. Press the F1 key to enter the BIOS Setup Utility when the ThinkPad logo is seen on the screen. The BIOS Setup Utility menu will be displayed. If a password prompt appears, type the correct password.
4. Select Config.
5. Select Serial ATA (SATA).
6. Select Compatibility.
7. Press the F10 key to save the new setup, and then select Yes.
8. Restart the computer.
9. Go to C:\DRIVERS\WIN\IRST\PREPARE, and double-click install.cmd.
10. Power off and on the computer.
11. Press the F1 key to enter the BIOS Setup Utility when the ThinkPad logo is seen on the screen. The BIOS Setup Utility menu will be displayed. If a password prompt appears, type the correct password.
12. Select Config.
13. Select Serial ATA (SATA).
14. Select AHCI.
15. Press the F10 key to save the new setup, and then select Yes. The computer will reboot and Windows XP will start.
16. The "Welcome to the Found New Hardware Wizard" appears. Click No, not this time, and then click Next.
17. Select Install from a list or specific location (Advanced), and then click Next.
18. Select Search for the best driver in these locations. Then select Include this location in the search:, specify the path, C:\DRIVERS\WIN\IRST, and click Next. The "Completing the Found New Hardware Wizard" appears.
19. Click Finish.
20. When the "System Settings Change" window appears, click Yes. The computer restarts.
-gan

KM4M-V + SATA Drive, Hangs at Boot, Tried IDE Drive and During Setup, Powers Off

I bought 2 KM4M-V boards to upgrade my ailing 1880+ systems. Then realized I needed DDR as well so went back for that and also decided to update CPU's to Sempron 2600+. Also picked up Seagate 80Gb SATA and a 350 watt PSU (Alaska ATX 350 P4) which was recommened for this board by the dealer.
I am having so much trouble I am about to throw in the towel. Since I am 'upgrading' everything in the system except the CDRom drive I should have just started all over with 64-bit systems but now I am kind of stuck since it is over 30 days ago I got the MB's.
Problem 1:
Using only the single SATA drive I never could get past the DMI Pool data line in Setup, it would just hang there. I read all about how to deal with SATA drives with this or similar boards here. SATA is enabled in BIOS but I can never get to the F6 load drivers step to try that. If I remove the SATA cable Setup will procede so it is something with the Seagate possibly? No jumpers needed and no preparation done to the drive. BIOS does not see the drive but the setup RAID utility does see it but says I cannot set up single drive as RAID of course, but it does report proper data about the drive. Never can get past Bios POST with SATA drive hooked up (channel 0 or 1)
Finally gave up on that and ran into Problem 2:
Put an older IDE drive in as only HD and XP Windows setup gets cranking along coping files then the system just dies. Like some pulled the plug suddenly. Happen every time. I checked for heat problems. Even ran through memory tests (SIMMTESTER), tried swapping cables, plugs and wall circuits. It dies every time no matter what.
Any suggestion would be greatly appreciated.

Quote from: Fredrik Åsenius on 24-November-05, 05:57:01
DMI pool data? When changing mobo but keeping hard disk one should do a repair install of Windows and install the mobo drivers for the new mobo.
I originally wanted to keep the Windows install but decided to remove original C drive and save for eventual D drive use. A repair install warns you that your 'My Documents' folder 'may' be deleted and I didn't want to risk it as I have years and years of photos I didn't want to risk losing.
Quote
Addit: Seems something isn't right in the IDE configuration, or what Windows think is the config.
Bios is happy with WD drive as single master on one channel and CDRom as single master on the other (No jumper on Drive- osnavi). Windows install starts out just fine with my intention of creating a new partition but then it just BOOM, power off. My preference is to use the new SATA Baracuda as system drive and my old IDE C drive as D drive...

SATA drive no longer boots

The PC was running fine for about two weeks with a single 160GB SATA drive.
One morning, with no hardware changes, the PC refused to boot. A blue screen of death flashed very quickly past as the PC rebooted. Windows suggested safe mode, and when I booted into safe mode the PC stopped loading drivers immediately after mup.sys. I've had this problem before with mup.sys on other PCs (I believe the real problem is the ACPI driver loaded immediately after mup.sys). In any case the solution is usually to remove any hardware or, in the worst case, re-install XP.
Running windows XP setup from CD it will no longer re-install onto the SATA hard drive. Even the recovery console will not work, claiming there is a problem with the drive. I know that the drive is not dead, because it gets as far as trying to install the ACPI driver.
Install a ATA HDD, installing XP on to it. Ran SP1 and all the updates. The ATA HDD worked OK until I plugged in the SATA HDD, which caused the new version of XP to hang at the mup.sys driver again. Disabled the SATA controller, and then everything works again. Ran all the updates for the motherboard and BIOS but that did not help. Switched SATA cables but did not help. Tried the SATA RAID controller but that did not make any difference. Variously tried disabling everything I could in the BIOS setup but that made no difference.
Now, I know that my no-name RAM might be a bit dodgy, and the PSU a little wimpy, but the PC works fine as long as the SATA HDD is either disabled or not plugged in. It actually ran perfectly for two weeks, and I was surprised how cool the CPU runs.
I looks like the next step is to try another SATA HDD, then PSU, then motherboard, but is there anything else which might help my situation before I go out and buy those items?

Well, it turns out it was the SATA HDD, and it seems to be repaired.
The method was to boot Windows XP from another HDD into safe mode and repair the drive. Windows would not boot from the SATA HDD at all, nor run in safe mode. When booted from the other HDD Windows would not access the SATA HDD normally, but would for some reason in safe mode. There must be a difference between the SATA drivers used in safe mode vs regular mode.
CheckDisk found many cross linked files and fixed them (took about an hour) and now the SATA HDD looks like it is working.
How did the file system get damaged? Good question, since I have never seen NTFS get messed up like this. In any case I'm probably going to replace the HDD in case it was the controller.

Satellite P300D-13N and XP Installation Issues (Sata-Driver)

Hi,
I have some issues with my XP-Downgrade.
I already tried integrating the Intel Storage Manager drivers into my XP-CD but unfortunately it didn't work.
Probably because i've been integrating ALL drivers, that were available and not just the one that should work for my chipset.
Anyway, in one of the threads in this forum there is a link to [THIS How To|http://aps2.toshiba-tro.de/kb0/TSB85017Z0000R01.htm] and I think I found my problem...
[Here|http://s5.directupload.net/images/080904/2eptrpzs.jpg] is a screenshot of my device manager (sorry for it being in german) of the pre-installed Vista.
As you can see, there is no information about the controller-Version.
So my question is, WHAT chipset is built into my laptop, because due to the fact that the Intel drivers do not work AND there is no information about any Intel Drive-Controller, I have no idea, which drivers i have to integrate into the XP-CD to get my XP-Installation to work. :(
Help :(
Thank you
Laptop: Satellite P300D-13N PSPDCE

Of course... I didn't want to bore you with the details... but I can do that ;)
I couldn't find any Chipset drivers on amd.com OR the toshiba website so I googled for the chipset and found [This Driver|http://eu.ecs.com.tw/ECSWebSite/Products/ProductsDetail.aspx?detailid=883&CategoryID=1&Deta ilName=Driver&MenuID=123&LanID=4] on the ECS-Elitegroup website.
I don't know why AMD doesn't upload this driver on their website, because I don't think I am the only one, who needed this SATA-Driver... ;)
Anyway, with the chipset-driver on my HDD, I created an XP-BootCD. I didn't know which driver (there are 3 or so in the package you can download on the ECS-Website), so I put *all* of them in the CD, which worked just fine. I think the *ahcix86.inf* in *\1_chipset_XP3264\XP3264\RAID7xx\x86\ i* is the important file for WinXP to load, but I'm not sure...
PS: The original catalyst drivers from ati.com do NOT work but the ones you can find [here|http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=EU] work fine ;) Just telling you so you don't try 3 different versions from ati.com before you try the toshiba-drivers... like i did :D

865pe-Neo2-V Installing Barracuda Sata drive

Trying to install a 400GB barracuda 7200.10- tried using on board sata port 1 but no joy. so bought a silicon image pci card sil 3114, but still unable to get that install correctly to recognise the sata drive.
have tried various configurations of ATA settings in the BIOS but with no effect. ???
but when i look in device manager the sil 3114 sata raid controller is okay but the sil 3114 satalink controller has the yellow !, i have tried updating the driver it says it has the latest.
would appreciate if anyone could shed some like in where i'm going wrong- other than opening up the pc
Thanks
Paul

Read Moan Guide 1st
You need to limit your SATA2 drive to SATA1 mode(since your board doesn't support SATA2), that can be done with HDD jumper configuration:
If still doesn't work, check your BIOS version:
- BIOS reported incorrect CPU temperature.
- Support HDD size over 136.9GB.
http://global.msi.com.tw/index.php?func=downloaddetail&type=bios&maincat_no=1&prod_no=591

New SATA drive showing as IDE drive in Bios

Just wanted to hear from some of you guys...not sure if this is right but seems weird for the bios to say my SATA drive is IDE..when its going through bios or if your selecting which drive to boot to first its listed as an IDE drive..could someone please tell me if this is correct...

This is correct.

[SOLVED] Problem with second SATA drive

My laptop has two hard drive bays, and just recently I added a second SATA drive (moved it from my old laptop) to the extra bay.
Now, anytime the second hard drive /dev/sdb has any heavy disk activity, it appears to cause a shutdown of the SATA port for the first drive (/dev/sda)! Though the second drive is still fine, and I can still write to it until the system crashes from the root drive (on /dev/sda) being shutdown.
If I don't mount and use the second drive, the first drive works just fine, and I can pound it with traffic without issue.
I can reproduce this problem by copying large amounts of data to drive 2.
This is when I get in my dmesg when the first SATA drive shuts down:
[ 3013.249525] ata1.00: exception Emask 0x0 SAct 0x7ff SErr 0x0 action 0x6 frozen
[ 3013.249532] ata1.00: failed command: READ FPDMA QUEUED
[ 3013.249539] ata1.00: cmd 60/08:00:78:b8:ba/00:00:24:00:00/40 tag 0 ncq 4096 in
[ 3013.249539] res 40/00:00:00:4f:c2/00:00:00:00:00/40 Emask 0x4 (timeout)
[ 3013.249543] ata1.00: status: { DRDY }
[ 3013.249545] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249559] ata1.00: cmd 61/08:08:b8:60:7b/00:00:29:00:00/40 tag 1 ncq 4096 out
[ 3013.249559] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249562] ata1.00: status: { DRDY }
[ 3013.249564] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249568] ata1.00: cmd 61/08:10:c0:60:7b/00:00:29:00:00/40 tag 2 ncq 4096 out
[ 3013.249568] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249570] ata1.00: status: { DRDY }
[ 3013.249572] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249576] ata1.00: cmd 61/08:18:c8:60:7b/00:00:29:00:00/40 tag 3 ncq 4096 out
[ 3013.249576] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249578] ata1.00: status: { DRDY }
[ 3013.249580] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249585] ata1.00: cmd 61/08:20:48:12:d7/00:00:18:00:00/40 tag 4 ncq 4096 out
[ 3013.249585] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249587] ata1.00: status: { DRDY }
[ 3013.249589] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249593] ata1.00: cmd 61/08:28:28:63:38/00:00:19:00:00/40 tag 5 ncq 4096 out
[ 3013.249593] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249595] ata1.00: status: { DRDY }
[ 3013.249597] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249601] ata1.00: cmd 61/08:30:28:6f:38/00:00:19:00:00/40 tag 6 ncq 4096 out
[ 3013.249601] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249603] ata1.00: status: { DRDY }
[ 3013.249605] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249609] ata1.00: cmd 61/08:38:28:98:ae/00:00:25:00:00/40 tag 7 ncq 4096 out
[ 3013.249609] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249611] ata1.00: status: { DRDY }
[ 3013.249613] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249617] ata1.00: cmd 61/08:40:d8:79:3b/00:00:25:00:00/40 tag 8 ncq 4096 out
[ 3013.249617] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249619] ata1.00: status: { DRDY }
[ 3013.249621] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249625] ata1.00: cmd 61/08:48:08:98:b6/00:00:18:00:00/40 tag 9 ncq 4096 out
[ 3013.249625] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249627] ata1.00: status: { DRDY }
[ 3013.249629] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249633] ata1.00: cmd 61/08:50:10:98:36/00:00:19:00:00/40 tag 10 ncq 4096 out
[ 3013.249633] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249636] ata1.00: status: { DRDY }
[ 3013.249640] ata1: hard resetting link
[ 3013.575549] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3013.576784] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 3013.578334] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 3013.578588] ata1.00: configured for UDMA/133
[ 3013.592223] ata1.00: device reported invalid CHS sector 0
[ 3013.592233] ata1.00: device reported invalid CHS sector 0
[ 3013.592238] ata1.00: device reported invalid CHS sector 0
[ 3013.592242] ata1.00: device reported invalid CHS sector 0
[ 3013.592246] ata1.00: device reported invalid CHS sector 0
[ 3013.592250] ata1.00: device reported invalid CHS sector 0
[ 3013.592254] ata1.00: device reported invalid CHS sector 0
[ 3013.592258] ata1.00: device reported invalid CHS sector 0
[ 3013.592263] ata1.00: device reported invalid CHS sector 0
[ 3013.592267] ata1.00: device reported invalid CHS sector 0
[ 3013.592271] ata1.00: device reported invalid CHS sector 0
[ 3013.592302] sd 0:0:0:0: [sda]
[ 3013.592306] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592310] sd 0:0:0:0: [sda]
[ 3013.592313] Sense Key : 0xb [current] [descriptor]
[ 3013.592320] Descriptor sense data with sense descriptors (in hex):
[ 3013.592323] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592342] 00 00 00 00
[ 3013.592351] sd 0:0:0:0: [sda]
[ 3013.592353] ASC=0x0 ASCQ=0x0
[ 3013.592358] sd 0:0:0:0: [sda] CDB:
[ 3013.592361] cdb[0]=0x28: 28 00 24 ba b8 78 00 00 08 00
[ 3013.592376] end_request: I/O error, dev sda, sector 616216696
[ 3013.592414] sd 0:0:0:0: [sda]
[ 3013.592417] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592421] sd 0:0:0:0: [sda]
[ 3013.592423] Sense Key : 0xb [current] [descriptor]
[ 3013.592428] Descriptor sense data with sense descriptors (in hex):
[ 3013.592431] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592449] 00 00 00 00
[ 3013.592458] sd 0:0:0:0: [sda]
[ 3013.592460] ASC=0x0 ASCQ=0x0
[ 3013.592465] sd 0:0:0:0: [sda] CDB:
[ 3013.592467] cdb[0]=0x2a: 2a 00 29 7b 60 b8 00 00 08 00
[ 3013.592482] end_request: I/O error, dev sda, sector 695951544
[ 3013.592505] sd 0:0:0:0: [sda]
[ 3013.592508] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592512] sd 0:0:0:0: [sda]
[ 3013.592514] Sense Key : 0xb [current] [descriptor]
[ 3013.592519] Descriptor sense data with sense descriptors (in hex):
[ 3013.592522] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592540] 00 00 00 00
[ 3013.592549] sd 0:0:0:0: [sda]
[ 3013.592551] ASC=0x0 ASCQ=0x0
[ 3013.592556] sd 0:0:0:0: [sda] CDB:
[ 3013.592558] cdb[0]=0x2a: 2a 00 29 7b 60 c0 00 00 08 00
[ 3013.592572] end_request: I/O error, dev sda, sector 695951552
[ 3013.592583] sd 0:0:0:0: [sda]
[ 3013.592586] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592589] sd 0:0:0:0: [sda]
[ 3013.592592] Sense Key : 0xb [current] [descriptor]
[ 3013.592597] Descriptor sense data with sense descriptors (in hex):
[ 3013.592599] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592618] 00 00 00 00
[ 3013.592626] sd 0:0:0:0: [sda]
[ 3013.592628] ASC=0x0 ASCQ=0x0
[ 3013.592632] sd 0:0:0:0: [sda] CDB:
[ 3013.592635] cdb[0]=0x2a: 2a 00 29 7b 60 c8 00 00 08 00
[ 3013.592649] end_request: I/O error, dev sda, sector 695951560
[ 3013.592665] sd 0:0:0:0: [sda]
[ 3013.592668] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592671] sd 0:0:0:0: [sda]
[ 3013.592673] Sense Key : 0xb [current] [descriptor]
[ 3013.592678] Descriptor sense data with sense descriptors (in hex):
[ 3013.592684] Aborting journal on device dm-0-8.
[ 3013.592701] EXT4-fs error (device dm-0) in ext4_reserve_inode_write:4476: Journal has aborted
[ 3013.592687] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592723] 00 00 00 00
[ 3013.592729] sd 0:0:0:0: [sda]
[ 3013.592730] ASC=0x0 ASCQ=0x0
[ 3013.592733] sd 0:0:0:0: [sda] CDB:
[ 3013.592735] cdb[0]=0x2a: 2a 00 18 d7 12 48 00 00 08 00
[ 3013.592744] end_request: I/O error, dev sda, sector 416748104
[ 3013.592752] Buffer I/O error on device dm-0, logical block 266057
[ 3013.592760] EXT4-fs warning (device dm-0): ext4_end_bio:250: I/O error writing to inode 5902184 (offset 258048 size 4096 starting block 266057)
[ 3013.592766] sd 0:0:0:0: [sda]
[ 3013.592768] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592771] sd 0:0:0:0: [sda]
[ 3013.592772] Sense Key : 0xb [current] [descriptor]
[ 3013.592776] Descriptor sense data with sense descriptors (in hex):
[ 3013.592778] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592790] 00 00 00 00
[ 3013.592795] sd 0:0:0:0: [sda]
[ 3013.592797] ASC=0x0 ASCQ=0x0
[ 3013.592800] sd 0:0:0:0: [sda] CDB:
[ 3013.592801] cdb[0]=0x2a: 2a 00 19 38 63 28 00 00 08 00
[ 3013.592811] end_request: I/O error, dev sda, sector 423125800
[ 3013.592817] Buffer I/O error on device dm-0, logical block 1063269
[ 3013.592822] EXT4-fs warning (device dm-0): ext4_end_bio:250: I/O error writing to inode 5898577 (offset 970752 size 4096 starting block 1063269)
[ 3013.592842] sd 0:0:0:0: [sda]
[ 3013.592845] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592849] sd 0:0:0:0: [sda]
[ 3013.592851] Sense Key : 0xb [current] [descriptor]
[ 3013.592856] Descriptor sense data with sense descriptors (in hex):
[ 3013.592859] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592877] 00 00 00 00
[ 3013.592885] sd 0:0:0:0: [sda]
[ 3013.592887] ASC=0x0 ASCQ=0x0
[ 3013.592892] sd 0:0:0:0: [sda] CDB:
[ 3013.592894] cdb[0]=0x2a: 2a 00 19 38 6f 28 00 00 08 00
[ 3013.592908] end_request: I/O error, dev sda, sector 423128872
[ 3013.592915] Buffer I/O error on device dm-0, logical block 1063653
[ 3013.592922] EXT4-fs warning (device dm-0): ext4_end_bio:250: I/O error writing to inode 5902187 (offset 1171456 size 4096 starting block 1063653)
[ 3013.592931] sd 0:0:0:0: [sda]
[ 3013.592934] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592937] sd 0:0:0:0: [sda]
[ 3013.592940] Sense Key : 0xb [current] [descriptor]
[ 3013.592945] Descriptor sense data with sense descriptors (in hex):
[ 3013.592947] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592966] 00 00 00 00
[ 3013.592974] sd 0:0:0:0: [sda]
[ 3013.592976] ASC=0x0 ASCQ=0x0
[ 3013.592980] sd 0:0:0:0: [sda] CDB:
[ 3013.592983] cdb[0]=0x2a: 2a 00 25 ae 98 28 00 00 08 00
[ 3013.592997] end_request: I/O error, dev sda, sector 632199208
[ 3013.593006] Buffer I/O error on device dm-0, logical block 27197445
[ 3013.593018] EXT4-fs warning (device dm-0): ext4_end_bio:250: I/O error writing to inode 6425165 (offset 151552 size 4096 starting block 27197445)
[ 3013.593028] sd 0:0:0:0: [sda]
[ 3013.593031] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.593034] sd 0:0:0:0: [sda]
[ 3013.593037] Sense Key : 0xb [current] [descriptor]
[ 3013.593042] Descriptor sense data with sense descriptors (in hex):
[ 3013.593045] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.593063] 00 00 00 00
[ 3013.593071] sd 0:0:0:0: [sda]
[ 3013.593073] ASC=0x0 ASCQ=0x0
[ 3013.593078] sd 0:0:0:0: [sda] CDB:
[ 3013.593085] EXT4-fs error (device dm-0) in ext4_reserve_inode_write:4476: Journal has aborted
[ 3013.593089] cdb[0]=0x2a: 2a 00 25 3b 79 d8 00 00 08 00
[ 3013.593104] end_request: I/O error, dev sda, sector 624654808
[ 3013.593111] Buffer I/O error on device dm-0, logical block 26254395
[ 3013.593115] lost page write due to I/O error on dm-0
[ 3013.593126] sd 0:0:0:0: [sda]
[ 3013.593129] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.593132] sd 0:0:0:0: [sda]
[ 3013.593135] Sense Key : 0xb [current] [descriptor]
[ 3013.593140] Descriptor sense data with sense descriptors (in hex):
[ 3013.593142] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.593161] 00 00 00 00
[ 3013.593169] sd 0:0:0:0: [sda]
[ 3013.593171] ASC=0x0 ASCQ=0x0
[ 3013.593175] sd 0:0:0:0: [sda] CDB:
[ 3013.593178] cdb[0]=0x2a: 2a 00 18 b6 98 08 00 00 08 00
[ 3013.593192] end_request: I/O error, dev sda, sector 414619656
[ 3013.593198] Buffer I/O error on device dm-0, logical block 1
[ 3013.593201] lost page write due to I/O error on dm-0
[ 3013.593211] sd 0:0:0:0: [sda]
[ 3013.593213] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.593217] sd 0:0:0:0: [sda]
[ 3013.593219] Sense Key : 0xb [current] [descriptor]
[ 3013.593224] Descriptor sense data with sense descriptors (in hex):
[ 3013.593227] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.593245] 00 00 00 00
[ 3013.593253] sd 0:0:0:0: [sda]
[ 3013.593256] ASC=0x0 ASCQ=0x0
[ 3013.593260] sd 0:0:0:0: [sda] CDB:
[ 3013.593262] cdb[0]=0x2a: 2a 00 19 36 98 10 00 00 08 00
[ 3013.593277] end_request: I/O error, dev sda, sector 423008272
[ 3013.593283] Buffer I/O error on device dm-0, logical block 1048578
[ 3013.593286] lost page write due to I/O error on dm-0
[ 3013.593298] ata1: EH complete
[ 3013.595707] EXT4-fs error (device dm-0) in ext4_dirty_inode:4603: Journal has aborted
[ 3013.596581] EXT4-fs error (device dm-0): ext4_journal_start_sb:370: Detected aborted journal
[ 3013.596591] EXT4-fs (dm-0): Remounting filesystem read-only
[ 3020.421558] journal commit I/O error
[ 3020.421570] journal commit I/O error
[ 3020.421574] journal commit I/O error
[ 3020.421578] journal commit I/O error
[ 3020.421581] journal commit I/O error
[ 3147.052191] ata1.00: exception Emask 0x0 SAct 0xf SErr 0x0 action 0x6 frozen
[ 3147.052197] ata1.00: failed command: READ FPDMA QUEUED
[ 3147.052209] ata1.00: cmd 60/50:00:d0:48:99/00:00:1c:00:00/40 tag 0 ncq 40960 in
[ 3147.052209] res 40/00:00:00:4f:c2/00:00:00:00:00/40 Emask 0x4 (timeout)
[ 3147.052212] ata1.00: status: { DRDY }
[ 3147.052213] ata1.00: failed command: READ FPDMA QUEUED
[ 3147.052218] ata1.00: cmd 60/18:08:28:49:99/00:00:1c:00:00/40 tag 1 ncq 12288 in
[ 3147.052218] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3147.052220] ata1.00: status: { DRDY }
[ 3147.052221] ata1.00: failed command: READ FPDMA QUEUED
[ 3147.052226] ata1.00: cmd 60/88:10:48:49:99/00:00:1c:00:00/40 tag 2 ncq 69632 in
[ 3147.052226] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3147.052228] ata1.00: status: { DRDY }
[ 3147.052229] ata1.00: failed command: READ FPDMA QUEUED
[ 3147.052234] ata1.00: cmd 60/20:18:00:a4:ba/00:00:24:00:00/40 tag 3 ncq 16384 in
[ 3147.052234] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3147.052236] ata1.00: status: { DRDY }
[ 3147.052239] ata1: hard resetting link
[ 3147.378368] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3148.066853] ata1.00: ACPI cmd ef/5a:00:00:00:00:a0 (SET FEATURES) succeeded
[ 3148.069139] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 3148.069393] ata1.00: configured for UDMA/133
[ 3148.080059] ata1.00: device reported invalid CHS sector 0
[ 3148.080066] ata1.00: device reported invalid CHS sector 0
[ 3148.080071] ata1.00: device reported invalid CHS sector 0
[ 3148.080075] ata1.00: device reported invalid CHS sector 0
[ 3148.080112] sd 0:0:0:0: [sda]
[ 3148.080114] Result: hostbyte=0x00 driverbyte=0x08
[ 3148.080117] sd 0:0:0:0: [sda]
[ 3148.080118] Sense Key : 0xb [current] [descriptor]
[ 3148.080123] Descriptor sense data with sense descriptors (in hex):
[ 3148.080125] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3148.080136] 00 00 00 00
[ 3148.080140] sd 0:0:0:0: [sda]
[ 3148.080142] ASC=0x0 ASCQ=0x0
[ 3148.080145] sd 0:0:0:0: [sda] CDB:
[ 3148.080146] cdb[0]=0x28: 28 00 1c 99 48 d0 00 00 50 00
[ 3148.080156] end_request: I/O error, dev sda, sector 479807696
[ 3148.080170] sd 0:0:0:0: [sda]
[ 3148.080171] Result: hostbyte=0x00 driverbyte=0x08
[ 3148.080173] sd 0:0:0:0: [sda]
[ 3148.080175] Sense Key : 0xb [current] [descriptor]
[ 3148.080178] Descriptor sense data with sense descriptors (in hex):
[ 3148.080180] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3148.080190] 00 00 00 00
[ 3148.080195] sd 0:0:0:0: [sda]
[ 3148.080196] ASC=0x0 ASCQ=0x0
[ 3148.080199] sd 0:0:0:0: [sda] CDB:
[ 3148.080200] cdb[0]=0x28: 28 00 1c 99 49 28 00 00 18 00
[ 3148.080209] end_request: I/O error, dev sda, sector 479807784
[ 3148.080216] sd 0:0:0:0: [sda]
[ 3148.080218] Result: hostbyte=0x00 driverbyte=0x08
[ 3148.080220] sd 0:0:0:0: [sda]
[ 3148.080221] Sense Key : 0xb [current] [descriptor]
[ 3148.080224] Descriptor sense data with sense descriptors (in hex):
[ 3148.080225] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3148.080236] 00 00 00 00
[ 3148.080241] sd 0:0:0:0: [sda]
[ 3148.080242] ASC=0x0 ASCQ=0x0
[ 3148.080245] sd 0:0:0:0: [sda] CDB:
[ 3148.080246] cdb[0]=0x28: 28 00 1c 99 49 48 00 00 88 00
[ 3148.080254] end_request: I/O error, dev sda, sector 479807816
[ 3148.080267] sd 0:0:0:0: [sda]
[ 3148.080268] Result: hostbyte=0x00 driverbyte=0x08
[ 3148.080270] sd 0:0:0:0: [sda]
[ 3148.080272] Sense Key : 0xb [current] [descriptor]
[ 3148.080274] Descriptor sense data with sense descriptors (in hex):
[ 3148.080276] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3148.080287] 00 00 00 00
[ 3148.080291] sd 0:0:0:0: [sda]
[ 3148.080293] ASC=0x0 ASCQ=0x0
[ 3148.080295] sd 0:0:0:0: [sda] CDB:
[ 3148.080296] cdb[0]=0x28: 28 00 24 ba a4 00 00 00 20 00
[ 3148.080305] end_request: I/O error, dev sda, sector 616211456
[ 3148.080315] ata1: EH complete
I have experimented, and found that if I turn off NCQ on the kernel command line in my bootloader (libata.force=noncq), that it takes longer before the problem occurs. Though, if I write enough to the second drive, it does still happen after a while, just greatly reduced its chances of happening.
Is it possible that the old drive (sdb) is causing the problem? I noticed that it is much noisier than I remember when the drive head moves around.
Another curiosity while I was trying to duplicate the problem:
- I start a large file copy from sda -> sdb
- At the same time in another terminal, I do "find / -print"
- When I hear the drive 2 head moving, it pauses the output of the "find" command.
Every time I hear the head move, I see the find output pause. Its almost like the drive seek on drive 2 causes the whole Sata controller to pause while the head moves. Very odd!
Anyone have any ideas? I think the next thing I will try is borrow a drive from another machine, and do the big write to it to see if I get the same results.
If it is of any help, here is some more info on the laptop:
lspci:
00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09)
00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04)
00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05)
00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05)
00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5)
00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5)
00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5)
00:1c.5 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 (rev b5)
00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05)
00:1f.0 ISA bridge: Intel Corporation HM67 Express Chipset Family LPC Controller (rev 05)
00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05)
00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05)
01:00.0 VGA compatible controller: NVIDIA Corporation Device 1251 (rev a1)
01:00.1 Audio device: NVIDIA Corporation GF116 High Definition Audio Controller (rev a1)
07:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0)
0d:00.0 Network controller: Intel Corporation Centrino Advanced-N + WiMAX 6250 (rev 5e)
13:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5209 PCI Express Card Reader (rev 01)
13:00.1 SD Host controller: Realtek Semiconductor Co., Ltd. RTS5209 PCI Express Card Reader (rev 01)
19:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)
cat /proc/interrupts:
CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7
0: 50 0 0 0 0 0 0 0 IO-APIC-edge timer
1: 958 0 0 0 0 0 0 0 IO-APIC-edge i8042
8: 1 0 0 0 0 0 0 0 IO-APIC-edge rtc0
9: 1675 0 0 0 0 0 0 0 IO-APIC-fasteoi acpi
12: 12257 0 0 0 0 0 0 0 IO-APIC-edge i8042
16: 24769 0 0 0 0 0 0 0 IO-APIC-fasteoi ehci_hcd:usb1, mmc0, nvidia
17: 142 0 0 0 0 0 0 0 IO-APIC-fasteoi snd_hda_intel
19: 0 0 0 0 0 0 0 0 IO-APIC-fasteoi rts_pstor
23: 1937 0 0 0 0 0 0 0 IO-APIC-fasteoi ehci_hcd:usb4
41: 1 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
42: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
43: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
44: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
45: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
46: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
47: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
48: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
49: 19406 0 0 0 0 0 0 0 PCI-MSI-edge iwlwifi
50: 36099 0 0 0 0 0 0 0 PCI-MSI-edge ahci
51: 14 0 0 0 0 0 0 0 PCI-MSI-edge mei
52: 386378 0 0 0 0 0 0 0 PCI-MSI-edge snd_hda_intel
53: 56803 0 0 0 0 0 0 0 PCI-MSI-edge eth0
NMI: 34 5 19 5 18 4 13 4 Non-maskable interrupts
LOC: 77964 17705 161241 14302 187823 16150 56845 12750 Local timer interrupts
SPU: 0 0 0 0 0 0 0 0 Spurious interrupts
PMI: 34 5 19 5 18 4 13 4 Performance monitoring interrupts
IWI: 0 0 0 0 0 0 0 0 IRQ work interrupts
RTR: 7 0 0 0 0 0 0 0 APIC ICR read retries
RES: 13721 7023 304 110 175 110 213 123 Rescheduling interrupts
CAL: 6941 7677 2774 7670 5804 7568 7655 7673 Function call interrupts
TLB: 366 545 268 179 310 272 212 166 TLB shootdowns
TRM: 0 0 0 0 0 0 0 0 Thermal event interrupts
THR: 0 0 0 0 0 0 0 0 Threshold APIC interrupts
MCE: 0 0 0 0 0 0 0 0 Machine check exceptions
MCP: 29 29 29 29 29 29 29 29 Machine check polls
ERR: 0
MIS: 0
smartctl --all /dev/sda
smartctl 5.43 2012-06-30 r3573 [x86_64-linux-3.5.3-1-ARCH] (local build)
Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: ST9500423AS
Serial Number: 5WS354LM
LU WWN Device Id: 5 000c50 044bb741b
Firmware Version: 0005DEM1
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Thu Sep 13 15:26:14 2012 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 105) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 113 099 006 Pre-fail Always - 54715920
3 Spin_Up_Time 0x0003 098 098 085 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 1114
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 069 060 030 Pre-fail Always - 10214892
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 2030
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 559
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 098 000 Old_age Always - 8590065667
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 053 049 045 Old_age Always - 47 (Min/Max 47/51)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 17
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 871
193 Load_Cycle_Count 0x0032 039 039 000 Old_age Always - 122293
194 Temperature_Celsius 0x0022 047 051 000 Old_age Always - 47 (0 17 0 0 0)
195 Hardware_ECC_Recovered 0x001a 113 099 000 Old_age Always - 54715920
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 67229123085518
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 1947733828
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 2798982459
254 Free_Fall_Sensor 0x0032 001 001 000 Old_age Always - 899
SMART Error Log Version: 1
ATA Error Count: 8 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 8 occurred at disk power-on lifetime: 2017 hours (84 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
04 71 09 a9 00 80 e0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
a1 00 00 00 00 00 a0 00 05:21:04.438 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:21:04.438 IDENTIFY DEVICE
00 00 00 00 00 00 00 ff 05:21:04.124 NOP [Abort queued commands]
a1 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY DEVICE
Error 7 occurred at disk power-on lifetime: 2017 hours (84 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
04 71 09 a9 00 80 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
ec 00 00 00 00 00 a0 00 05:21:04.438 IDENTIFY DEVICE
00 00 00 00 00 00 00 ff 05:21:04.124 NOP [Abort queued commands]
a1 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY DEVICE
00 00 00 00 00 00 00 ff 05:20:58.805 NOP [Abort queued commands]
Error 6 occurred at disk power-on lifetime: 2017 hours (84 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
04 71 09 a9 00 80 e0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
a1 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY DEVICE
00 00 00 00 00 00 00 ff 05:20:58.805 NOP [Abort queued commands]
a1 00 00 00 00 00 a0 00 05:20:58.761 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:20:58.725 IDENTIFY DEVICE
Error 5 occurred at disk power-on lifetime: 2017 hours (84 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
04 71 09 a9 00 80 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
ec 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY DEVICE
00 00 00 00 00 00 00 ff 05:20:58.805 NOP [Abort queued commands]
a1 00 00 00 00 00 a0 00 05:20:58.761 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:20:58.725 IDENTIFY DEVICE
2f 00 01 10 00 00 a0 00 05:20:58.724 READ LOG EXT
Error 4 occurred at disk power-on lifetime: 2017 hours (84 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
04 71 09 a9 00 80 e0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
a1 00 00 00 00 00 a0 00 05:20:58.761 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:20:58.725 IDENTIFY DEVICE
2f 00 01 10 00 00 a0 00 05:20:58.724 READ LOG EXT
61 00 08 ff ff ff 4f 00 05:20:58.724 WRITE FPDMA QUEUED
61 00 08 ff ff ff 4f 00 05:20:58.724 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 6 -
# 2 Short offline Aborted by host 90% 1 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
smartctl --all /dev/sdb
smartctl 5.43 2012-06-30 r3573 [x86_64-linux-3.5.3-1-ARCH] (local build)
Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint M6
Device Model: SAMSUNG HM320JI
Serial Number: S16LJF0QB02815
LU WWN Device Id: 5 0f0000 001202815
Firmware Version: 2SS00_01
User Capacity: 320,072,933,376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Thu Sep 13 15:27:10 2012 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 110) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 110) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0007 252 252 025 Pre-fail Always - 2562
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 810
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 092 092 000 Old_age Always - 4842
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 440
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 154
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 71
194 Temperature_Celsius 0x0022 073 073 000 Old_age Always - 55 (Min/Max 17/55)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 1
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 252 252 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x0032 252 252 000 Old_age Always - 0
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 534
225 Load_Cycle_Count 0x0032 077 077 000 Old_age Always - 236803
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Note: selective self-test log revision number (0) not 1 implies that no selective self-test has ever been run
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Last edited by johni (2012-09-16 00:46:54)

It appears my drive one really is failing. It was the first drive and not the second making the loud head seek sound. I borrowed another drive from a friend, and copied my drive one to it. No problems with the new drive in place.

Which 1TB (or bigger) SATA drive is the coolest/quietest/least power-hungry

I have a Power Mac G4 Dual 1.25 GHz MDD (it's this model here) which (as it's unmodified) runs very hot & noisy much of the time.
What doesn't help is that I have 3 hard drives installed. 2 of these (including the boot drive) are IDE (80 GB & 120 GB), and are attached to the cables at the front of the machine (am I right in thinking that this is the ATA-66 bus?). The third is a SATA drive (250 GB) connected to one of the sets of cables at the back of the machine (the ATA-100 bus?) via an IDE -> SATA adapter (not a PCI card).
This adapter took me many weeks of research to track down (& order online from the USA) as there didn't appear to be (at the time - a few years ago) anyone here in the UK that made or sold these adapters. (The opposite adapter - IDE drive to SATA cable - was freely available ironically, even in my local electronics shop). The physical size of the adapter means that I can't sit one of the other drives in the empty drive bay at the back of the machine.
A few months ago, as I was almost out of hard drive space, I decided to get a new (SATA) drive to replace the existing 3 drives. As well as giving me lots of capacity, one drive is going to use less power than 3, give off much less heat than 3, and hopefully reduce the fan noise.
Incidentally, I've found many good articles on reducing heat/power consumption/noise in MDD Macs - see here, here, here, here & here.
At the time, 1TB was the largest size available. After much research, along with some forum postings - see here & here - I decided to go for the Samsung Spinpoint F1 drive, which is currently quite cheap - see here.
However, I recently discovered that Seagate now makes a 1.5 TB drive, which would obviously be preferable - see here & here although it is much more expensive - see here.
However, there are many reports of problems with the Seagate drive - see here, here & here.
What I'm wondering is if there are any drives that are bigger than 1TB apart from the Seagate?
If not, would people recommend that I chance going for the Seagate, and hope that I don't have the problems, or that I'll be able to flash the firmware at some future point to sort the problem if it occurs (I have Virtual PC 7.0.2 installed, running Windows 2000 Service Pack 4 - would this enable internal hard drives to have their firmware updated?) or should I just play safe and go for the Samsung, even though it's "only" 1TB?
The largest capacity money can buy is my primary concern, followed by low power usage, low heat output & low noise.
Many thanks.

Thanks for the info.
I don't really see the point in the expense of a PCI card when the IDE -> SATA adaptor works fine, and if I bought a PCI card, I'd then feel obliged to go through the hassle of selling the adaptor on eBay to try to recoup part of the cost of the PCI card.
I should have mentioned before that I want to format my new drive as a single partition, in Mac OS Extended (Journaled) format, and to boot from it. I only want the new drive in the Mac - I don't want any other drives in there. Apart from increased capacity & performance, and reduced power consumption, heat & noise - the main point of getting the new drive is so that there is only one drive in my Mac. Having more than one is a complete pain for me.
At the moment, despite having "Put the hard disk(s) to sleep when possible" unchecked in the Energy Saver pane of System Preferences, all 3 drives spin down very soon after they stop being accessed, which means an infuriating delay (& spinning beach ball) when they spin up again. One or more of them spinning up even interrupts music playing sometimes, and when I go to shut down the computer, if they are spun down but mounted on the desktop, they spin up again before they spin down as part of the shutdown procedure! Also, with more than one drive, I can't tell which drive a file/folder is on just by looking at it, if it's on the desktop.
As far as Other World Computing goes, they may ship to the UK, but by the time the international shipping charges are added, I very much doubt if the total cost of a new drive would work out cheaper than ordering from a UK supplier & getting free shipping.
Another potential problem I've discovered with the Seagate drive is actually a quote from the Other World Computing website that's reproduced in comment number 66 (on page 3) of the MacRumors Forums thread that I gave the link to in my initial post. Basically it says that if you format the Seagate drive as a single partition on a Mac, the performance isn't acceptable. It's apparently fine though if it's partitioned in 2 equal size volumes, or if you format it as an NTFS or FAT32 drive. Neither of these work-arounds are any use to me though.
Everything so far suggests that I should just go for the Samsung 1 TB drive, but I'm hesitant to do so until it's confirmed to me that there aren't any other drives out there that are bigger than 1 TB apart from the Seagate, and also, knowing my luck, the day after I buy the Samsung, Western Digital or Hitachi or someone will bring out a flawless 1.5 TB drive for not a lot more money, and I'll be kicking myself for ending up with only 2 thirds of the capacity than I could have had...

How to connect a SATA Drive in a G4 MDD Desktop Mac?

Due to much more needed harddisk space for music production on my G4 1.25 GHz Dual PC, I ordered and just received a SATA 500 GB internal Harddiskdrive.
Under "About This Mac" in the System Profiler I get a list of all my internally already connected ATA Drives. But there is also a (empty) category available, named "Serial-ATA" which I strongly assume stands for SATA. I further think once such a category is existing I should be able to connect a SATA drive.
Now:
1. Can I connect the new SATA HD internally in my Dual G4 or must I use the Drive as an external Firewire Drive (of course in a special housing)?
2. If it is possible to built in a SATA drive, must I buy an adapter in any form, because the interface on the SATA drive is different from the cable endings in my Mac?
3. If so, what is such an Adapter be called (from Inerface A name to Interface B name) and do I get it at an electronic store?
4. Is there anything crucial I do need to know regarding this matter (maybe voltage compatibility, adjustments on SATA drive or in my Macintosh G4, etc.)?
5. And if it should not be possible to use the HD internally (as in question 1.), are there housings with Firewire 800 connectors available for SATA drives which I can use?
I would be very glad for your specialist help! Thank you!
Steve
G4 1.25 GHz Dual PowerPC 1 MB L3 cache processor · 1.25 GB DDR SDRAM · Mac OS X (10.4.8) · 19" CRT ƒAQTOR 19+ Monitior · AD/DA Converter MOTU Traveler

Thank you all (Malcolm Rayfield · The hatter · Rodney Culling) so very much. I thought I would be lost and stuck - on contrary I got your huge help.
Unfortunately I bought already the SATA 7200.10 and it had been delivered. But I am very happy to hear that there are PCI SATA cards available and I preferably would like this solution to have the Drive as an internal drive. It is for me easier to tame the noise not having an additional drive in my Mini recording studio.
I will investigate into the prices of those cards and only do hope that the price for such PCI SATA cards are not to expensive otherwise my bread deliverer (boss) will refuse. He was already not excited to hear I ordered a SATA drive but there was no ATA anymore available at my usual source and if I later upgrade to a G5 I can take the drive with me. I only will have then the reverse situation using some of my older ATA drives in a new G5.
Thanks a million again for your kind and unexpected fast help. Thanks!
Steve
G4 1.25 GHz Dual PowerPC 1 MB L3 cache processor · 1.25 GB DDR SDRAM Mac OS X (10.4.8) · 19" CRT ƒAQTOR 19+ Monitior · AD/DA Converter MOTU Traveler

I have a MDD dual 1.25ghz processors and I would like to know which sata drives will work with the Sonnet Seria ATA pci card?

Which sata drives will work with the Sonnet Tempo Serial ATA card?

Pretty much any of the SATA 3.0 Gbps drives.
Western Digital Black and Blue and Hitachi 7K drives are all good choices.
If you try a SATA 6.0 Gbps drive, it will need to be jumped to limit to SATA 3.0 Gbps.

No longer can write to my external SATA drive...

I was editing in FCP Studio 2 on a my MacPro 2x2.8 Quad Core, running MacOS 10.5.2, connected to a Highpoint X4 SATA drive, via the Highpoint RocketRaid 2314MS card. At some point the MAC detected a problem with the drive, and apparently it has changed the drive to read only. My timeline plays OK, but a lot of clips are marked as off-line, although I re-rendered them and they play. I ran the internet verification check from Highpoint, and it said the drive was normal. MAC disk utility will not let me change permissions on the external SATA. What should I do? Edit deadline approaching...there goes the weekend.

Well, the tech-support guy at Highpoint was going to e-mail me some steps, after he talked with someone about some MAC procedures. He thought that I would have to insert some code. There are three UNIX files on the drive that are trying to"fetch" something. Since my permissions have changed, I can't delete them. The e-mail from tech support never arrived last night. I'm in tthe CST zone, so it's still about two hours until Highpoint opens their doors. The RAID warning lights gave never changed from green to red. No beeps or chirps either. The on-line drive verification that took 3 hours, said the drive status was Normal.
Paul

Hp pavilion g7 notebook - DVD RAM GT80N SATA Drive

After upgrading from Win 8 to 8.1 my DVD RAM GT80N SATA Drive is no longer recognized by my laptop.
Any ideas how to resolve this issue?
Regards ... John
This question was solved.
View Solution.

Hi John,
Open windows Control Panel, open Device Manager, expand DVD/CD-ROM Drives, right click the drive and select Uninstall - when this has completed, restart the notebook and let Windows fully load for a couple of minutes before checking if it's now listed correctly.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

After upgrading from Win 8 to 8.1 my DVD RAM GT80N SATA Drive is no longer working

After upgrading from Win 8 to 8.1 my DVD RAM GT80N SATA Drive is no longer recognizing discs. When I first put a disc in the drive runs for a bit and then stops. I've tried updating the driver but it says it has the most current driver. Under manage, it does not show any error codes and it says it is working correctly. I've looked at the regedit and it does not have any of upper and lower filters. I've tried disabling, rebooting, and reenabling. What am I missing? Another issue I've had since upgrading is that my network adapter needs reset several times a day in order to remain connected to wifi.

Hey hvbnfrgvn,
Thank you for the information on your HP Pavilion g7-2270us Notebook PC.
I suggest following the steps in this document for Drive Cannot Read Discs (Windows 8).
If your CD/DVD Drive Is Not Detected (Windows 8), follow the steps in this document.
I hope this information helps, please keep me posted on how it goes.
Best of luck and have a great day!
I worked on behalf of HP.

Preparing SATA drive

Similar Messages

Maybe you are looking for