Presence/phone status at Jabber popup window

Tear Team,
There was a question from some customers.
if we are dialing an internal extension on ip phone, jabber window pops up for this user.
at this windows, there are no information for presence status/phone status.
I'm thinking it souled be a small step to place this information to this window!?
many thanks in advanced - Gerald

Hi,
Short answer is NO, the mobile phone it self is not integrated with Jabber or IM.
Jabber does not have full access to the mobile device and is not integrated in such a way that it will show on a call.

Similar Messages

Jabber for Window, phone mode, how to disable "use my computer for calls"

We have a Citrix environment and only want to control the Cisco deskphone with Jabber for Windows in the phone mode.
We use CUCM 8.6.2 and I have installed Jabber for Windows 9.7.0 and all works fine, I can control my deskphone, make and receive calls, phonebook and Outlook integration works fine.
Is it possible to disable "use my computer for calls" as we do not want users to make calls via Citrix, but only use the deskphone for this.
Thanks, Perry

Hi Matthias,
Soft-phone mode cannot be disabled. Supported Features on Virtual Environment are the following.
Supported Features
    Instant messaging and presence with other Cisco Jabber clients
    Desk phone control
    Voicemail
    Presence integration with Microsoft Outlook 2007, 2010 and 2013
We have an existing defect which is in Terminated state because feature is not supported hence cannot be fixed.
CSCub40605 - J4W - Ability to disable softphone mode in Citrix environment.
HTH,
Please rate if you find this post helpful.
Regards,
Mohammed Noor

Jabber For Windows - Available Status on Hibernation

We're running Jabber for Windows 9.1.1 ansd see an issue which I think is casued by hiberantion.
A laptop user will be at their pc and and Available, then on leaving their desk, they would typically just close their pc lid, hibernating the pc, and leave the building.
Their status stays as Available, when of course thay are not. I understand that CUP has not received a specific state change event to update their status, but does any one know if their is a timeout/keepalive that would eventually indicate the user is offline?
I've not had chance test this in detail yet, I've just noticed it a few times when users near me are no longer at their desk, but still show as available.
Has anyone out there come across this? Or do I need to be telling our users they should sign out of Jabber before hibernating their pc's?
Regards
Kelvin

Hi All,
We have also been suffering from this issue ( I supect) - Running 9.1.2 client but it is also in 9.1.1. Same CUPS 8.6 version etc.
Closing my PC lid - PC Asleep
I can been seen as Away from another PC.
Opening my PC lid - I am still seen Away - both on my own jabber and a watcher client. I haven’t logged out and my status does not change even when I am back on the keyboard etc.
I can change it manually and then its appears correct both on my PC and the other PC.
Or
If I log out of jabber and back in – the correct status is shown both locally and remotely.
This appears confusing to the end user who thinks presence isn't working correctly. we have a number of jabebr users that move between locations for meetings and hence often just close thier PC lid and move locations. FYI - this also happens within the same site.
can you advise if there is a TAC case and if so if we can get an update ?
thanks
Russ

Phone account tab on jabber on windows missing

Hi All,
i had a problem with jabber on windows, i already login and can do a IM and see the presence, but i cant do voice/video call,
when i try to see the setting on file - options - i cant see any phone account tab, that should be i used to put my phone configuration,
i use a BE6K with unified PM, are anyone experienced this before?
thanks
Nafi.

You need to add the following on your xml for the phone account option to show on the newer Jabber versions
Not_Set
Save the file as jabber-user.xml to test,
Get the file to this folder:
C:\Users\User\AppData\Roaming\Cisco\Unified Communications\Jabber\CSF\Config.
If this solves the issue upload the xml as jabber.xml on a TFTP.
Hope it helps!

Jabber for Windows cannot control 8841 desk phone

Hello Team,
We have a problem with desktop phone control in case of 8841 phone.
When the user try to switch to the 8841 phone in Jabber then we got the following error message in the log:
2014-11-07 09:39:53,855 ERROR [0x00000298] [ice\TelephonyAdapterPhoneDevice.cpp(178)] [TelephonyAdapter] [TelephonyAdapter::selectDeviceImpl] - switchMode to device [SEP84802D7698D6] failed with error [eDeviceRegCouldNotOpenDevice]
We get the red X on the phone icon, and the desktop phone control is not working.
If the same user try to control 7940 phone, then it's working fine.
The environment: UCM 9.1.2.12901-3, CUPS 9.1.1.51900-5, Jabber for Windows 10-5.2
Edited:
Same issue with UCM 10.5.1, CUPS 10.5.1, and Jabber for Windows 10.5.2.
Regards,
Zsolt

Hi Zolt,
The RT phones need below end user permissions also in order to control deakphones:
Standard CTI Allow Control of Phones supporting Connected Xfer and conf
Standard CTI Allow Control of Phones supporting Rollover Mode
If they are not added, please add these permission.
Regards

Jabber for Windows Call popup photo

We have a Jabber for windows deployment currently running in our lab environment. In the buddy list we have the contacts with their photo. When we start a call or receive a call a call popup screen appears. In this screen the photo of the called person i not displayed..
Is this possible? If i look at the pictures cisco provides there is always a photo of the caller.

Hi,
This is very common scenario in case the number to contact resolution does not work. You need to create directory lookup rules to modify the incoming number so that it matches the number configured for the contact in question.
Here's an example
You have a contract named John Doe with a DN configured in AD as 101. The contact has an avatar.
You get an incoming call from John Doe but the incoming number is 9101.
This will result in the avatar not being displayed for a contact because number 9101 does not match the contact's configured DN.
So in summary you need to use Directory Lookup Rules and/or Application Dial Rules
HTH,
Christos

Jabber for Windows 9.0.1 phone control of Cius?

Can the Jabber for Windows client control a Cius like it can a 79XX phone?

Jabber for Windows 9.0(1) will not be posted automatically for all customers.
An internal communication will be issued to all internal CSM's and PSM's in the next couple of days explaining the exact procedure for requesting access to the client and how to raise the ops request to make it available for the customer org in question ... so reach out to the your Partner manager to understand that procedure and to enable access for your customers.
Regards,
John

Jabber for Windows Group Configurations IM/Presence only

Hi All,
Jabber for Windows can be customized for groups using the Cisco Support Field at CSF device.
http://www.cisco.com/en/US/docs/voice_ip_comm/jabber/Windows/9_0_1/b_jabber_win_icg_chapter_0110.html#JABW_TK_C6D444A8_00
How can I configured this for users without a CSF device (IM/Presence only users)?
Regards
Helmut

Well, you may have 1 global jabber-config.xml for all your deskphone mode only Jabber and customized ones for CSFs, all pushed via CUCM. That's we do usually.
The restriction is to not be able to customize deskphone only config after installation for a specific group.
Regards
Christophe
Sent from Cisco Technical Support iPhone App

Jabber for Windows 9.2.1 Contact Away status doesn't show duration

.Jabber for Windows 9.2.1 Contact "Away" status doesn't show duration. I am wondereing if it is possible with Cisco Jabber client. Microsoft OCS client used to show.

Hi,
This is currently not supported in Jabber.
If you think that this feature should be in Jabber, you can open a TAC case and do Enchancment request with them?
Regards,
Srdjan

How to stop popup window using phone layout for display - Responsive HTML5, RH11

Hello,
I'm using the new Responsive HTML5 output in RH11. For some of my hyperlinks, I want to use a pop-up to display the linked topic. In the output, the pop-ups work, but they are automatically displayed using the phone layout, with the associated navigation buttons at the bottom, the help title, and so on. I don't want this - I just want a plain popup window. So, I tried to add a Screen Profile, set to 400 x 500 pixels exactly (thinking that this is bigger than a phone, but smaller than a tablet). I also added a corresponding Screen Layout. In the popup properties, I set the popup size to be 400 x 500 pixels. I guess there is something else I need to do to get this to work... but I don't know what that is. (I tried creating a new Window on the Project Set-up tab, and I tried creating a different master page. These things didn't work.)
Can anyone tell me if what I'm trying to do with these popups is just a bad idea and it won't work well with certain browsers?
Thanks!
Alexandra

I am confused as the responsive layouts are one size fits all, that is the point of them. You have one layout that morphs according to window size.
Screen Profiles are only used within Multiscreen HTML5 layouts where you can map screen profiles to different adaptive screen layouts, such as desktop, tablet and phone. That mapping does not apply to responsive layouts.
See www.grainge.org for RoboHelp and Authoring tips
@petergrainge

Linkinking error msg on status bar and a popup window

Hi
My requirement is that whenever an error msg comes on status bar after execution,i need to double click
on that error msg and followed by that a popup window should appear with the customised details about error msg.
plz suggest some solution or some function module which gives popup on double clicking on error msg.
Thanks in advance,
Arya.

Hi,
my question is that this popup should be populated by customized details i mean suppose error message on status bar is asking 'authority scheck for one or more plants have failed.would you like to see the details'.Now if user double clicks on status error message pop up screen should contain all the plant numbers for which authorization has failed.I hope this clarifies my question.
thanks

Cisco Jabber for Windows Voicemail issue

At this I'm in processing of implementation Cisco Jabber UC solution for big Company.
I use CUCM 9.1.2, Cisco IM and Presence 9.1.2, CUC 9.1.2, Cisco Jabber for Windows 9.6.1.
I have issue in Cisco Jabber with VoiceMail Integration - when I leave voice message for any user,
than this message is arrived only him Cisco IP Phone, but not in him Cisco Jabber.
From Cisco Jabber Connectivity status in help menu I see that VoiceMail service is successfully connected
and I see VoiceMail button in Cisco Jabber.
How can I resolve this issue?

Have you configured the UC Service profile on CUCM with both Voicemail server and mailbox servers?

Jabber for Windows 9.2 Deskphone Control

Hi,
I have a deployment with:
CUCM 9.1(1a) (9.1.1.20000-5)
IM and Presence 9.1(1a) 9.1.1.20000-5
Jabber for Windows 9.2.3(4417)
I have got most features working but Deskphone Control is not working. I can see the devices associated with my user from within Jabber when I select "Use my phone for calls" but cannot control them.
The connection status page shows the correct IP address for the CTI server.
I have spent hours reading through various documents and forums which seem to contain contradictory advice.
To clarify theserver versions that I have deployed support the new UC Services which are referenced from a Service Profile which is assigned to the user.
I am not making any progress resolving this issue. Does anyone have any advice on how to move forward with this?
Thanks
James

Hi Daniel,
we have a Problem with AD-User and DeskPhone ...
The "Active Local User" can control a DeskPhone
The "Active LDAP Synchronized User" can't control a DeskPhone from same PC, but he can controll a Softphone.
Cisco UCM - 9.1.2.10000-28 with LDAP Sync/Auth via 3269 (success)
Cisco UCMIMP - 9.1.1.31900-1
Cisco Jabber - 9.6.0 Build 17088
564 INFO [0x0000226c] [src\common\thread\WorkerThread.cpp(94)] [csf.ecc] [run] - Started thread: CtiConnection
564 DEBUG [0x0000226c] [utilities\socket\TcpSocketHelper.cpp(82)] [csf.ecc] [connect] - About to connect to 172.20.1.11
564 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(957)] [csf.ecc] [SendRequest] - CDPProvider::SendRequest, msg.sequenceNumber=1, pObject=0477A214, pdunames[msg.msgID]=PROVIDER_OPEN_REQUEST
564 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(967)] [csf.ecc] [SendRequest] - SendRequest setting msg.sequenceNumber to , msg.sequenceNumber=2
564 DEBUG [0x0000226c] [oneprovider\QBE\ProtocolElement.cpp(330)] [csf.ecc] [encode] - Message::encode: , msg.protoVersion=0x000e0000, msg.msgID=3, sizeof(Header)=32, fixedSize=108, varSize=90
564 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(973)] [csf.ecc] [SendRequest] - SendRequest Succeed., pdunames[msg.msgID]=PROVIDER_OPEN_REQUEST, msg.sequenceNumber=2
564 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(986)] [csf.ecc] [SendEvent] - CDPProvider::SendEvent, pObject=0477A210, nType=1001
564 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(919)] [csf.ecc] [OnEvent] - CDPProvider::OnEvent, pObject=0477A210, nType=1001, pvThis=0477A210
564 DEBUG [0x0000226c] [pper\DeskPhoneConnectionContext.cpp(317)] [csf.ecc] [ecc::DeskPhoneConnectionContext::OnProviderEventUpdated] - OnProviderEventUpdated(1001), state=STATE_INITIAL_LOGIN, loginstate=LOGINSTATE_OPENING
564 DEBUG [0x0000226c] [c\deskphoneprovider\DPProvider.cpp(1148)] [csf.ecc] [DispatchTheMessage] - CDPProvider::DispatchTheMessage, nPduNum=4, pduName=PROVIDER_OPEN_RESPONSE
564 DEBUG [0x0000226c] [c\deskphoneprovider\DPProvider.cpp(1232)] [csf.ecc] [DispatchTheMessage] - Received , pdunames[nPduNum]=PROVIDER_OPEN_RESPONSE, seqNum=2
564 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(267)] [csf.ecc] [HandleMessage] - CDPProvider::HandleMessage, nPduNum=4
564 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(407)] [csf.ecc] [HandleResponse_ProviderOpen] - CDPProvider::HandleResponse_ProviderOpen
564 DEBUG [0x0000226c] [oneprovider\QBE\ProtocolElement.cpp(360)] [csf.ecc] [decode] - Message::decode: , totalSize=107, type=0, magic=4294958557, msg.protoVersion=0x000e0000, pduNum=4, hdrSize=32, fixedSize=52, varSize=31
564 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(415)] [csf.ecc] [HandleResponse_ProviderOpen] - CUCM protocol version: , resp.getProtoVersion()=0x000e0000
564 WARN [0x0000226c] [c\deskphoneprovider\DPProvider.cpp(1026)] [csf.ecc] [ResetHeartbeatTimer] - m_heartbeatIntervalS not set, timeout not set.
845 DEBUG [0x0000226c] [c\deskphoneprovider\DPProvider.cpp(1148)] [csf.ecc] [DispatchTheMessage] - CDPProvider::DispatchTheMessage, nPduNum=126, pduName=PROVIDER_OPEN_COMPLETED_EVENT
845 DEBUG [0x0000226c] [c\deskphoneprovider\DPProvider.cpp(1290)] [csf.ecc] [DispatchTheMessage] - PDUTYPE_ProviderEvent or PDUTYPE_Heartbeat, nPduNum=126, pdunames[nPduNum]=PROVIDER_OPEN_COMPLETED_EVENT
845 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(267)] [csf.ecc] [HandleMessage] - CDPProvider::HandleMessage, nPduNum=126
845 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(488)] [csf.ecc] [HandleEvent_ProviderOpenCompleted] - CDPProvider::HandleEvent_ProviderOpenCompleted
845 DEBUG [0x0000226c] [oneprovider\QBE\ProtocolElement.cpp(360)] [csf.ecc] [decode] - Message::decode: , totalSize=161, type=0, magic=4294958557, msg.protoVersion=0x000e0000, pduNum=126, hdrSize=32, fixedSize=72, varSize=65
845 WARN [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(502)] [csf.ecc] [HandleEvent_ProviderOpenCompleted] - ProviderOpen failed: reason: 0x8ccc0060, Directory login failed - authentication failed.
845 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(986)] [csf.ecc] [SendEvent] - CDPProvider::SendEvent, pObject=0477A210, nType=1008
845 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(919)] [csf.ecc] [OnEvent] - CDPProvider::OnEvent, pObject=0477A210, nType=1008, pvThis=0477A210
845 DEBUG [0x0000226c] [pper\DeskPhoneConnectionContext.cpp(317)] [csf.ecc] [ecc::DeskPhoneConnectionContext::OnProviderEventUpdated] - OnProviderEventUpdated(1008), state=STATE_INITIAL_LOGIN, loginstate=LOGINSTATE_LOGGING_IN
845 DEBUG [0x0000226c] [pper\DeskPhoneConnectionContext.cpp(891)] [csf.ecc] [ecc::DeskPhoneConnectionContext::DPLogoutWorkItem::DPLogoutWorkItem] - create DPLogoutWorkItem
845 DEBUG [0x0000226c] [pper\DeskPhoneConnectionContext.cpp(892)] [csf.ecc] [ecc::DeskPhoneConnectionContext::DPLogoutWorkItem::DPLogoutWorkItem] - Setting _loginState = LOGINSTATE_DISCONNECTING
845 DEBUG [0x0000226c] [c\deskphonewrapper\CC_DPService.cpp(926)] [csf.ecc] [ecc::CC_DPService::raiseLoginFailure] - raiseLoginFailure(5)
845 DEBUG [0x000013a0] [pper\DeskPhoneConnectionContext.cpp(898)] [csf.ecc] [ecc::DeskPhoneConnectionContext::DPLogoutWorkItem::run] - DPLogoutWorkItem::run()
845 INFO [0x0000226c] [\deskphonewrapper\CC_DPService.cpp(1078)] [csf.ecc] [ecc::CC_DPService::notifyConnectionStatusObservers] - dispatching ConnectionStatus Change eIdle
845 DEBUG [0x00002788] [c\deskphonewrapper\CC_DPService.cpp(298)] [csf.ecc] [ecc::CC_DPService::start] - Finished waiting for deskphone to go in to service...
845 INFO [0x000013a0] [rc\deskphoneprovider\DPProvider.cpp(218)] [csf.ecc] [Close] - CDPProvider::Close
845 INFO [0x0000226c] [control\CallControlManagerImpl.cpp(3092)] [csf.ecc.evt] [ecc::CallControlManagerImpl::notifyConnectionStatusChange] - CONNECTION_STATUS_CHANGE: eIdle
845 ERROR [0x00002788] [control\CallControlManagerImpl.cpp(1989)] [csf.ecc] [ecc::CallControlManagerImpl::doConnect] - doConnect() returnCode : AuthentincationFailure
845 DEBUG [0x000017a0] [s\telephonyservice\ECCObservers.cpp(153)] [csf-unified.telephony.ECCObserverLogger] [ECCObservers::onConnectionStatusChange] - onConnectionStatusChange(status = eIdle).
845 DEBUG [0x0000226c] [\deskphonewrapper\CC_DPService.cpp(1014)] [csf.ecc] [ecc::CC_DPService::raiseProviderStateChange] - Got cxn change, disconnecting deskphone video Idle
845 DEBUG [0x000013a0] [rc\deskphoneprovider\DPProvider.cpp(957)] [csf.ecc] [SendRequest] - CDPProvider::SendRequest, msg.sequenceNumber=2, pObject=0477A214, pdunames[msg.msgID]=PROVIDER_CLOSE_REQUEST
845 ERROR [0x00002788] [control\CallControlManagerImpl.cpp(2025)] [csf.ecc] [ecc::CallControlManagerImpl::doConnect] - doConnect() returnCode : eDeviceRegAuthenticationFailure
845 DEBUG [0x000017a0] [elephonyservice\BackgroundWorker.cpp(35)] [csf-unified.telephony.BackgroundWorkerLogger] [BackgroundWorker::doTask] - Adding new task to BackgroundWorker. Task name is: TelephonyAdapter::onConnectionStatusChange
845 INFO [0x0000226c] [rc\deskphonevideo\DeskPhoneVideo.cpp(76)] [csf.ecc] [ecc::DeskPhoneVideo::disconnect] - disconnecting
845 DEBUG [0x000013a0] [rc\deskphoneprovider\DPProvider.cpp(967)] [csf.ecc] [SendRequest] - SendRequest setting msg.sequenceNumber to , msg.sequenceNumber=3
845 INFO [0x00002788] [control\CallControlManagerImpl.cpp(2411)] [csf.ecc] [ecc::CallControlManagerImpl::doDisconnect] - --->
845 DEBUG [0x000017a0] [common\processing\TaskDispatcher.cpp(29)] [TaskDispatcher] [Processing::TaskDispatcher::enqueue] - Enqueue TelephonyAdapter::onConnectionStatusChange - Queue Size: 9
845 DEBUG [0x0000226c] [c\deskphonevideo\DeskPhoneVideo.cpp(315)] [csf.ecc] [ecc::DeskPhoneVideo::stopCdp] - Stopping CDP
845 DEBUG [0x000013a0] [oneprovider\QBE\ProtocolElement.cpp(330)] [csf.ecc] [encode] - Message::encode: , msg.protoVersion=0x000e0000, msg.msgID=9, sizeof(Header)=32, fixedSize=4, varSize=0
845 INFO [0x00002788] [pper\DeskPhoneConnectionContext.cpp(267)] [csf.ecc] [ecc::DeskPhoneConnectionContext::stop] - DeskPhoneConnectionContext::stop
845 DEBUG [0x000013a0] [rc\deskphoneprovider\DPProvider.cpp(973)] [csf.ecc] [SendRequest] - SendRequest Succeed., pdunames[msg.msgID]=PROVIDER_CLOSE_REQUEST, msg.sequenceNumber=3
845 DEBUG [0x0000226c] [c\deskphonevideo\DeskPhoneVideo.cpp(318)] [csf.ecc] [ecc::DeskPhoneVideo::stopCdp] - CDP stopped
845 INFO [0x000017a0] [src\AccessoriesManager.cpp(234)] [csf.accessory.event] [accessory::AccessoriesManager::onConnectionStatusChange] - Received onConnectionStatusChange - eIdle
845 DEBUG [0x00002788] [pper\DeskPhoneConnectionContext.cpp(891)] [csf.ecc] [ecc::DeskPhoneConnectionContext::DPLogoutWorkItem::DPLogoutWorkItem] - create DPLogoutWorkItem
845 INFO [0x000013a0] [\deskphoneprovider\CtiConnection.cpp(49)] [csf.ecc] [stop] - CtiConnection::stop
Thanks,
Guennadi

Jabber for Windows and Iphone

We are running Jabber on cucm 9.1 WE use microsoft RDS and all works fine locally. users can sign in with their AD account and see their presence, use their deskphone and receive email. that works on both the windows and Iphone clients.
When they are logging in via a anyconnect VPN however. the im and presence shows no status for anyone, even though they are logged in but the phone and vociemail is fine, calls can be made and received. The ASA is not blocking anything so not sure where to start with this one

I just did a full deployment for jabber 4 windows iphone, ipad and android and to get my presence status working as well as photos shown and directory searches I had to make use of the BDI config in my jabber-config.xml file on the cucm as well as the UC services on the cucm and mine is working 100%.
That is all why I am asking.

Jabber for Windows On-Premises Deployment.

I´m deploying a solution of CUCM BE 8.6 with CUC 8.6 and CUPS 8.6. At this momento all is working on the CUCM and CUC. But i´m not sure if all is fine on the CUPS.
I have integrated all application whit an LDAP (Microsoft AD). Now I´m configuring Jabber for Windows and the users have IM and status monitoring (presence) working fine. But They need to have voice functionalities to make and recive calls.
I try to make call with jabber and using the pc to make call, but just can make calls; when some one try to call me, they receive a fast busy tone.
Then i tried to use jabber with an IP Communicator associated to the same user; and just in this scenario other users can call me.
The question is. On-premises deployments, jabber for windows requiere to have associated a desk phone or softphone to make and receive calls?, or i need to do some thing to give to jabber in self the ability de make and receive calls with out any other device associated?
Thanks.

Hi Chris, do you mean that in sofphone mode Jabber do no need the ip communicator to make an receive calls?
Becouse right now i have jabber and a CSF configured and associated to the user. But they can not receive calls, just can make calls.
Only when associate the ip communicator the user can receive calls.
Any idea of what could be happenning?
Thanks
Hello again,
I did some tests and a review of the configuration, but i can´t solve the issue.
the Users with jabber for windows can receive calls but they can not make if they do.
Only if they use an IP communicator associated to jabber client, they can make and receive calls
Must be jabber working by in self to make and receive calls, no matter if have or not associated a desk phone or softphone?
What do you think i need to verified?
I´m sending a file with screen shots to explain the issue.
thanks in advance

Presence/phone status at Jabber popup window

Similar Messages

Maybe you are looking for