Presonus Faderport problem with Logic Pro 7 running Snow Leopard

I've been been using Tiger to run Logic Pro 7 without any problems for the past few years. I've held out on upgrading to Snow Leopard since everything worked so nicely, but I finally gave in and loaded 10.6.6. Logic Pro 7 seems to be okay except for my Faderport control surface functionality. I upgraded to the newest FP firmware, and Logic 7 recognizes the FP, but it doesn't work. When I open a Logic project I get a pop up dialog box that says:
Module file "Faderport" is too new and cannot be used with this version of Logic control surfaces. Please get an update of the Logic control surface application file. I also get another dialog box that says: "Loading Module Faderport..." But nothing happens.
I'd appreciate any and all ideas on how I might deal with this. Thanks!

Hi,
I'm getting this message since updating the Faderport Firmware. I'm using Logic 7 in Tiger still.
How did you fix the install pref?

Similar Messages

  • Problem with Time Machine, running Snow Leopard

    Hi all,
    Last week I had a new hard drive fitted into my iMac 8,1, after which Snow Leopard was reloaded (10.6.3 from the disc, updated to 10.6.8), followed by the restoration of data via Time Machine from my external hard drive. Whilst my Mac is now running beautifully, I am having problems backing up with Time Machine.
    When I run a backup, it prepares about 100,000 items, then starts to backup, usually about 650mb. It crawls along in kb until it gets to about 1mb, then jumps quickly to the end, but then it adds extra mb on the end. Then it suddenly starts again "preparing x items....." and off it goes again.
    I have tried repairing the backup disc, and it appears to be ok. I even erased it and started again. Time Machine did a full backup (139gb) in about 2 hours, then immediately added another 640mb at the end - strange, but I do at least have a full backup from yesterday. But now, everytime I run backup, it looks for the same sort of figure (650-700mb) and then goes round in circles.
    Any help would be very much appreciated!
    Thanks, David

    Hi Eric
    Thank you for your reply.  Here are the screenshots for each change:
    Having prepared about 95,000 items, the backup of 612mb begins
    14 minutes later a message appears
    Another 3 minutes and another message. You will see from this screenshot that the backup figure has changed to 613.1mb
    Another 30 seconds and it all begins again....
    And finally, 7 more minutes pass, another 96,000 items are prepared, and another 604.8mb backup begins.
    I might add, that between posting this morning, and your reply, I also went into disk utility, chose the top leve of the external drive, clicked on the partition tab, charged current to 1 partition, renamed the drive, erased it, and did a full back up of 139GB. After 137GB it started again, looked for 602mb, backed them up and finished the backup, which is why TM states that the last back up was at 18:16 today.
    Thanks again
    David

  • I have a macbook pro running snow leopard. Just recently I cannot view youtube videos and other online videos. I recently updated my flashplayer plugin and I believe that is the problem. Is the latest flashplayer plugin compatible with 10.6.8?

    I have a macbook pro running snow leopard. Just recently I cannot view youtube videos and other online videos. I recently updated my flashplayer plugin and I believe that is the problem. Is the latest flashplayer plugin compatible with 10.6.8? If this is so, I need to find an older flash player plugin to reinstall. I do not want to upgrade from 10.6.8 at this time because I have 18 yrs. worth of financial records on Quicken that I have read will not work with Lion and I've read bad things about running music programs on Maverick.

    rayvonr wrote:
    ...I have 18 yrs. worth of financial records on Quicken that I have read will not work with Lion and I've read bad things about running music programs on Maverick.
    1)  Quicken 2007 for Intel (Snow Leopard, Lion, Mt. Lion and Mavericks) is a full featured app that can be downloaded from Intuit for $15 and will work with your data file if you are using Quicken 2005, 2006 or 2007 (if you version is earlier, let me know for more instructions on easy conversion):
    http://quicken.intuit.com/personal-finance-software/quicken-2007-osx-lion.jsp
    2) Partition your hard drive, or add an external hard drive and install Mavericks there and "dual-boot" to operate your music programs in Snow Leopard and experiment with them in Mavericks.
    DO NOT install Mavericks over Snow Leopard!

  • I have a mid 2010 Macbook Pro running Snow Leopard and foolishly upgraded to Yosemite.  Is it possible to go back in time with Time Machine and reinstall Snow Leopard.  Then upgrade to Lion or Mavericks?  Any other ideas on how I can exit Yosemite?

    I have a mid 2010 Macbook Pro running Snow Leopard and foolishly upgraded to Yosemite. Now have numerous problems.  Is it possible to go back in time with Time Machine and reinstall Snow Leopard?  Then upgrade to Lion or Mavericks?  Any other ideas on how I can exit Yosemite?

    Once you get yourself back to Snow Leopard, if you still want to upgrade somewhat, I would suggest the following:
    1. Get an external hard drive that you can use for experiments with new OS versions. You could partition it into 2 or 3 partitions. You could then clone your existing Snow Leopard system to one partition using Carbon Copy Cloner (well worth $40) or SuperDuper ($25).
    2. Buy OS X Mountain Lion for $20, through the Apple online store (I don't think it's available through the App Store). Apple has decided to make it very difficult for anyone to get Mavericks unless they have already downloaded it.
    You will receive two e-mails from Apple, one containing a PDF with a redemption code, and one with the password you will need to unlock the PDF. Using the code, you will download Mountain Lion from the App Store, where it will appear among your Purchased items.
    After ML finishes downloading, its installer app will launch itself. When you see this launch screen, QUIT the install app immediately! Go to your applications folder, find the Install OS X Mountain Lion app, and copy it to a safe location outside of your Applications folder. Keeping one or more copies will allow you to reinstall without unnecessary aggravation if you later need or want to do that. At this point, you can re-launch the Installer in the Applications folder and let it run. You can install it on a clean partition on your external HD, or you can allow it to upgrade the Snow Leopard clone you created on your external drive, or you can do both. This should allow you to test how everything works for as long as you like.
    3. If you left yourself a free partition on your test drive, try a clean install of Yosemite and set everything up from scratch (do not migrate anything). This will allow you to see whether your problems with it were related to something in your Snow Leopard system.

  • Need to connect a web cam and external mike to my McBook Pro running snow leopard for a Skype session with another school. Attached an HP webcam (USB) and can't get video. Any suggestions?

    Need to connect a web cam and external mike to my McBook Pro running snow leopard for a Skype session with another school. Attached an HP webcam (USB) and can't get video. Any suggestions?

    -->Click HERE<--  Does item "B" (Turn video on/off) in the last topic on the page help?
    You control the camera for Skype from within Skype, so  Skype must be running to running to make video work.
    Message was edited by: EZ Jim
    Mac OSX 10.7.4

  • Problems with Booting from the Snow Leopard Install Disc

    I need to do a reformat of my iMac drive and reinsall Snow Leopard.  Then I want to run System Migration and move the contents of my Mac Pro (running Snow Leopard) over to the iMac.
    I placed the retail Snow Leopard installation disc and held the "C" key down during restart.  My optical drive make a bit of random noise and eventually ejects the SL disc.  I've tried a CD, movie dvd and another software program installation disc and none of them seem to be able to be read.  I've sold the Mac Pro and am in a bit of a bind as I need to get this done and shipped out.  I'm also going to have to wipe the Mac Pro drives clean and do a reinstall of Snow Leopard.
    Can anyone help?
    Thanks,
    John

    Do you have the original install discs that came with the computer?
    If you do, try powering up the mac pushing in the disc and hold the OPTION key, which will bring up the start up manager, select the insrall disc to boot from.
    After booting, select the language, on the next page go to the menu bar and select Utilities/disk utilities, select your volume (default name is Macintosh HD, or what ever you ma have named it) First aid tab, run verify disk.
    If it comes up with errors (they will be in red font) click repair disk. Rerun this till it it comes up with "this disk seems OK i(n green font)
    Then quit the installer and eject the disk.
    Try the Snow Leopard disk using the same proceedure (power up, push in disk, holding the OPTION key) to boot to the start up manager, and select the SL disk, and do a clean install.
    Make sure that you have a retail install disk (white SL on it)
    You can try this from the retail SL disc, if you do not have the Original disc(s) you should include all of them to the person you seel/give it to.
    After install, follow these instructions.
    http://www.thesafemac.com/how-to-prepare-your-mac-for-sale/
    http://support.apple.com/kb/HT5189?viewlocale=en_US&locale=en_US
    Hope this helps

  • I'm using a macbook pro, running snow leopard. Yesterday I got around to emptying my trash for the first time in quite awhile and was surprised by how much there seemed to be in there. Immediately after a question mark symbols appeared on all my hard disk

    I'm using a macbook pro, running snow leopard. Yesterday I got around to emptying my trash for the first time in quite awhile and was surprised by how much there seemed to be in there. Immediately after a question mark symbol appeared on all my hard disk folders. If I click on these question marks I get a message saying ' the item can't be found'.

    mpagan47 wrote: a question mark symbol appeared on all my hard disk folders.
    Not sure where these hard disk folders are located that you are referring to?  Finder, Finder tool bar, Finder side bar, Desktop, Dock? 
    More then likely they are  an alias that not longer point to the orginals,  thus the question mark.
    I would reboot.  Delete icons if an alias and just recreate by dragging from the source. Try right click (control) click to remove.

  • I have a new l7 macbook pro running snow leopard.  When I try to boot into windows7 32bit, I get either a blue, black, or flickering screen.  Then I have to physically shut down and try again.  At that point it will load correctly.  Any help?

    I have a new l7 Macbook Pro running snow leopard.  When I tried to to install windows 7 32 bit on bootcamp, I kept getting a flicking black and blue screen when it tried to install. (Tried several times).  I finally downloaded the bootcamp windows support to a flash.  I inserted that and finally got it installed.  Now when I try to boot into windows I get either a solid black (sometimes blue) or flickering screen and windows will not start up.  If I then physically shut down the mac and restart, it will finally boot into windows where it tells me that windows was shut down unexpectently and once I click start windows normally, it will boot up.  That will generally let me boot into windows for the remaining of the day.  The next day, the same thing happens again.  I have tried reinstalling several times, and the same thing keeps happening.  It is not my windows disk because it installs flawlessly on the mid 2008 macbook pro.  Anyone know how to fix this?

    I own HDM 2011. But they have products that aren't listed or hard to find too.
    Recommending Pro version for one user's needs:
    http://www.wilderssecurity.com/showthread.php?t=297756
    Pro vs HDM 2011 feature comparison
    http://www.paragon-software.com/home/hdm-personal/comparison.html
    Forum topics:
    http://www.wilderssecurity.com/showthread.php?t=297756
    http://www.wilderssecurity.com/showthread.php?t=303155

  • I have lost my installation disk for my mac book pro running Snow Leopard 10.6." Where can I replace it?"

    I have lost my installation disk for my mac book pro running Snow Leopard 10.6." Where can I replace it?"

    You can get replacement System Install & Restore CD/DVDs from Apple's Customer Support - in the US, (800) 767-2775 - for a nominal S&H fee. You'll need to have the model and/or serial number of your Mac available.

  • Will Pages work with MacBook Pro OS Snow Leopard 10.6.8?

    I am wondering if the Pages App will work with MacBook Pro OS Snow Leopard 10.6.8.  I am getting conflicting information from people, and I don't want to purchase and download the App if I am not able to use it.  Thanks for your help.

    Thanks so much for your help, Michael. Glad to hear it works for you.  This gives me enough confidence to go ahead and order the App.  Thanks again. 

  • Can I share my CD/DVD drive from my laptop running OS 10.4.11 with my MacPro running Snow Leopard?

    Can I share my CD/DVD drive from my laptop running OS 10.4.11 with my MacPro running Snow Leopard?

    Hi, no idea if this works in 10.4.x, but...
    http://hints.macworld.com/article.php?story=2009012605560521
    Might have a couple of other ideas if it doesn't.
    Hmmmm, looks like 10.5.2 might be required for that, let me know...
    http://www.mariasguides.com/2008/02/14/mac-os-x-1052-adds-dvd-or-cd-sharing/

  • Will firefox 5 run on a mac pro running snow leopard

    I like FF but am concerned whether it will run on my mac pro running snow leopard, since the download information says it is a windows program.

    Snow Leopard being Mac OSX 10.6
    You need to download the version for Mac, not the .exe which is for Windows.
    www.mozilla.com or if you prefer a certain language no given then look at http://www.mozilla.org/en-US/firefox/all.html and look down the middle which is Mac OSX.

  • Problems with Photoshop CS4 on Snow Leopard 10.6.8

    I just upgraded to Snow Leopard 10.6.8 and now my Photoshop CS4 is constantly crashing on me.  Adobe was no help.  Is there anything I can do to fix this?  I don't want to purchase CS5 just to prevent this from happening. I had no problems with CS4 w 10.5.8.  I also did a software update on CS4.  Help please!!

    "...Adobe was no help...."
    Meaning what exactly? CS4 should work with some problems. Google, "cs4 and snow leopard" and read the issues. You are also not alone if you look the the right side of this web page under, "More Like This" you'll others with the same issue.

  • New Mac Pro running Snow Leopard?

    I literally picked up a new Mac Pro today at the local Apple Store and it is running Snow Leopard (10.6.4). Is this usual? I don't get the latest operating system on this puppy?

    Be grateful.
    You don't want Lion, not today, not quite yet.
    Apple still sells 10.6.3 DVD as well as a combo Snow Leopard and Lion on USB thumb drive $69.
    In the past priro two OS, there was 10.X.6 DVD but not this time.
    So Apple has their giant 1GB combo updates plus another 500MB of supplemental updates for other programs and patches.
    Your OEM DVD has Apple Hardware Test.
    Mac Pro can still run 10.6.8 just fine.
    Macs that only use Lion use network installs, .network hardware test.
    Lion recovery partition though can check the health of all hidden hard drive partitions as well as repair so that is nice and for $30 you might want to TEST Lion on another hard drive at some point. Better that then splurging on 3rd party system tools.
    The 2010 can take a faster processor. The limitation? still SATA2 means bandwidth and performance hit for storage hits glass ceiling. That SATA 6G SSD for instance.
    Blessing in disguise to me.

  • How can I synch iCal with iPhone when running Snow Leopard?

    I'm running Snow Leopard (10.6.8), and I cannot upgrade to Lion or Mountain Lion because I have an Intel Core Duo iMac.
    I absolutely MUST be able to synch my desktop calendar with my iPhone. This is an essential function for my life - I cannot believe that Apple would make me buy an entirely new computer, just so that my desktop calendar sychs with my iPhone.
    Can some please help me figure this out?
    Thank you!!
    -Paul

    Maybe you might get more response in the MobileMe forum as it sounds like an issue with that to me and I don't use it so am unable to help in that area.
    Hope you get it sorted out soon.

Maybe you are looking for

  • How to find out what files a package has installed?

    Sometime you installed a package, but you don't know the name of the command to run and you don't know the name and location of the configuration files. There are conventions but is there a way to show those information explicitly?

  • How to capture non-work related time in SAP

    Hi gurus, We are trying to implement a new system where by the shop floor person can enter his travelling time, break time and working time. Billing can only be done for working time. I know the regular way of entering time in CAT2 and transferring i

  • Dynamic addressing in Empty BPEL

    hi I am trying to implement dynamic addressing in Empty BPEL(because my BPEL gets input from JMS queue so there is no requirement of Client) But without the client partner link(which BPEL generates in case of syn or async BPEL) i am not able to imple

  • Reg:SAP GEM add on

    Hi experts, I have a requirement to imlpement the add on SAP GEM(Global Employee Management it is a SAP HR sub module)  in our production environment. Currently we are on ECC6.0 with SAPHR-SAPKE60028 and EA HR-SAPKGPHD17 levels. Can some pls.let me k

  • Problem with LR 4.3 update

    Just installed updates to LR 4.  Received error messages, "assertion failed"; and "LR cannot use the catalog because it is not writable and cananot be opened."  Help!