Previously burned DVD's not recognized

Since I upgraded to SL- I've started having problems with my Optical drive (I think).
Previously created older movies burned on DVD-Rs (G5 PPC) when inserted in my iMAC are not recognized as DVDs.
Instead I get a message that I've inserted a blank CD (not DVD) in the machine.
These movies used to play just fine on my iMAc and still do on stand-alone players.
My Mac further indicates that these are blank CDs -and can be re-burned (which should be impossible).
Also, if I insert an older DVD with a PAPER label, the optical drive spins down and stops dead.
Non-paper label disks spin normally.
Am I looking at a failing optical player-- failed software, or both?
any help appreciated.

"My Mac further indicates that these are blank CDs -and can be re-burned"
You cannot "reburn" DVD -Rs.
"Also, if I insert an older DVD with a PAPER label"
As a precaution, never insert a DVD or CD that has a paper label. The drive heat can sometimes melt the glue leaving little pieces of paper inside the slot drive during ejections, burning, etc. Reason why I hate slot drives. Wish Apple bring back the tray drives.
If I were you, I would clean my drive "several" times w/a drive cleaner, repair permissions and restart the computer after each burning session.
If little pieces of paper are stuck inside the drive, you will have no alternative but to take your computer to a repair shop for removal & cleaning.

Similar Messages

I have a Power Mac G4. I have previously burned DVDs with no problem. Now I get an error message stating it doesn't recognize the disc and an error

I have a Power Mac G4 with OX 10.4.11. I have previously burned DVDs with no problem. Now I've gotten two different sets of messages. One states that
the disc is not readable and an error code: 0x8002006D. The more recent message states the disc is incompatible and an error code: 0x80020025.
What is going on? I need to burn discs immediately for a conference next week.

"The more recent message states the disc is incompatible and an error code: 0x80020025."
The error (0x80020025) refers to an unsupported drive (not disk). I've read about relaunching the Finder to correct the problem. Choose "Force Quit" from the Apple Menu and then choose "Finder." Click "Relaunch" and see if the drive still produces the error. If there's no change, I'd be tempted to replace the drive.

Pioneer sata dvd-rw not recognized

I have a Pioneer sata dvd-rw not recognized problem. I installed a new Pioneer dvd burner. It is Sata. It works fine, but every time I boot into Win xppro sp3 I get the found new hardware, it lists the correct drive and has the error that it cannot be installed. Just have to cancel that message, but yesterday I went to install a new copy of windows on another drive connected to the the pc, the windows cd booted up asked the usual questions and then started setup and message came up and said it could not continue, because there was no cd drive. Once I quit laughing and pointing to the cd drive, I figured I better find out if it came be fixed. I also have a sata hard drive connected internally to the pc. This works fine also. If I boot to the sata drive the sata dvd burner is recognized and it is installed. Works fine. Does anyone want to tackle this one? I tried showing the windows cd where the burner was and expained to it that it was inside the drive already, but it just won't listen. The pc worked fine with the old ide drive. Thanks in advance.
MSI K8NDiamond Plus , AMD 4800 X 2, Xigmatek HDT-S1283 CPU Cooler
2 GB Corsair TWINX2048-3200C2PT DDR-400
EVGA 8800gt, Thermalright HR-03 Plus cooler
Mushkin 580 watt quad rail power supply, RaidMax Smilodon case with 3 fans

I assume that you have tried installing the drivers? If not try these:
For SATA 1-4 connectors:
NVIDIA GeForce nForce4 SLI x16 chipset dirvers (http://global.msi.com.tw/index.php?func=driverfile&dno=2437&i=1)
This nForce CK804+C51 Win2K/XP driver 6.82 WHQL package contains the below components:
Ethernet driver version 5.09 (WHQL)
Network Firewall management tools
SMBus driver version 4.5 (WHQL)
Installer version 4.89
Win2K IDE SATARAID driver version 5.52 (WHQL)
Win2K IDE SATA_IDE driver version 5.52 (WHQL)
Win2K RAIDTOOL application version 5.52
WinXP IDE SATARAID driver version 5.52 (WHQL)
WinXP IDE SATA_IDE driver version 5.52 (WHQL)
WinXP RAIDTOOL application version 5.52
SATA 5-6 connectors:
Silicon Image 3132 Serial-ATA & RAID Drivers (http://global.msi.com.tw/index.php?func=driverfile&dno=2426&i=0)
Description • WHQL certification for K8N Diamond and P4N Diamond
• Supports Win2000/Win XP for K8N Diamond and P4N Diamond
• Driver version: 1.4.3.0(SATA), 1.2.3.1(RAID)
• WinXP 64-bit driver version: 1.2.3.1(RAID only)

My dvd drive not recognized in device manager,getting the yellow explanation mark.

my dvd drive not recognized in device manager,getting the yellow explanation mark. Tried uninstallingdevice drive and scanning for new hardware. scanned for updates, etc. I getting no results. The laptop is a Pavilion DV5. Thanks

Hi,
It could be that the drive has a Hardware issue, but try the following.
From the Start Menu, open All Programs, open Accessories, right click the Command Prompt and select 'Run as Administrator'. In to the prompt type the following command and hit enter.
sfc /scannow ( note that there is a space between sfc and the / )
Let the process complete, then type exit and hit enter.
Next, open Device Manager, right click the DVD drive and select Uninstall. When this has completed, restart the notebook and let Windows rediscover the device and check.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

HT5639 after The Boot Camp for Windows 8? DVD Drive Not Recognized or Reading CD/DVD

after i made The Boot Camp Setup for running Microsoft Windows 8? DVD Drive Not Recognized or Reading CD/DVD

thanks for the response
1. Yeah I thought that's a mandatory thing because i need to be able to control the brightness with my keyboard, updated graphics card, boot camp control panel, etc
2. No there's no enable for this because Windows 8 recognizes it as a "disconnected device" and asks me to reconnect the dvd drive to the machine (which it obviously already is).
3. Ive tried those before, also even editing the registry but it didnt work.
It's weird because it never happened before on Snow Leopard » Lion bootcamp driver updates. Just in Mountain Lion

Burned DVD does not play in MacBook Pro but does in other computers.

Hi, everyone. I have recently had some issues playing backed up copies of DVDs that I have. These two particular DVDs have not been able to play properly with DVD player. They will begin playing but never actually make it to the main menu screen. I have tried downloading other media software, such as VLC, but this has not been of any help.
What's even more bizarre is that they successfully play in my old Dell computer (Inspiron 700m) and a desktop HP that the rest of the family uses. Does anyone have any insight or advice? Thanks.

In addition, make sure the burned DVDs are not dirty, cracked and/or smudged in any way. http://docs.info.apple.com/article.html?artnum=50448 *How to Handle and Clean CD and DVD Discs*
Your drive may need cleaning. Cleaning kits can be purchased from any store that sells CD/DVDs.
!http://i50.tinypic.com/izvwo1.gif!

Copying previously burned DVDs

I can copy previously burned DVD's on my Mac mini through disk utilities, but my mother-in-law can't on her new iMac flat screen. Is there another way to copy them on her iMac? Is there another program she needs to use?

If your MIL has a +"new iMac"+ then you posted in the wrong discussion area. All new iMacs are Intel based.
http://docs.info.apple.com/article.html?artnum=301724-en How to identify your iMac
http://docs.info.apple.com/article.html?path=Mac/10.4/en/mh355.html Getting information about your computer
You can have this info displayed on the bottom of every post by going to 'My Settings' which is located in the column on the right under your name, and filling in the information asked for.
Thank you
You will need to re-post concerns over in the Using DVDs and CDs with your Intel-based iMac Forums where the Intel users hang out.

DVD Drive not recognized/Reinstall of OS 10.3.9 - No install disc(s)??

I have an iMac G4, single 1.25 GHz currently running 10.3.9. After a recent bout of trying to install additional RAM and the Superdrive failing and needing to be replaced suddenly the new DVD burner I had installed to replace the original Superdrive isn't being recognized by the iMac. It will play DVDs put in it (commercial or previously burned) but it will not allow me to burn new content, either files or through iDVD. The computer guys who installed the new DVD drive tell me some of the system pathways (or similar such language) that recognize the drive have been messed up and the easiest way to go would be to reinstall the overall system.
First, I'm curious if there might be an easier solution to try and get the iMac to re-recognize the new DVD drive for burning. And that's in large part because . . .
Second, I can't seem to find the computer install discs that came with my computer some five years ago. I have the OS 9 disc, which doesn't help me, but the OS X disc is no where to be found.
I've seen some other posts with suggestions on where to find versions of Panther and Tiger to buy. If I have to buy one of those I will, but I'd really just like to be able to restore my system's previous functions.
Thanks for any help you can offer!

missalee:
First Repair Disk Permissions in Applications > Utilities > Disk Utility.
Then try Patchburn
Hope it helps.
cornelius

Previous made DVDs now not loading

Previous DVDs that I have made on my computer are not being recognized now.
Back up of iPhoto, iDVD projects, iTunes back up. I have Sony, Imation, Verbatim
brands and nothing opens anymore. They were all created on this computer.
The only change was to install iLife 08 which went awful on install and finally had
to do a clean install. I have done repair permissions etc.... I can put a BLANK DVD
in and the computer reads it fine, I can burn photos to it, and read it .... but anything
that I had made previously on a DVD will not open. CD's seem to be fine. I did have
to do something in iDVD 08 to get all the past versions to show up properly. I also
have a Apple laptop and all the DVD's open and play fine in that. But that only has
iLife 06, didn't want to chance any problems with iLife '08 in that.
May I have changed some setting along the way that has caused this?
System Preferences are set correctly for when a CD DVD is installed.

Old Toad if you happen to recheck this......
I ran the hardware disk on my eMac and everything came up fine. I can install a new DVD and record on it just fine. I can put in a DVD install disk and it works fine, I can put in a store bought DVD movie and it plays just fine. I can put in a previous made CD and that works fine. It is just a previous made
DVD from this computer that will not work. I did the safe boot, I set up another user, I did the compressed air in the tray. Nothing. And this all happened right after a clean install and the installation of iLife 08. I have no access to my photos, iDVD's previously made.
Any more thoughts ????

CD/DVD Drive Not Recognized

I have a Dell Laptop with Vista. After installing iTunes the CD/DVD drive is no longer recognized by the computor. I have to remove the upper filter for the CD/DVD drive using 'regedit', reboot the computor and the drive is recognized again. But, iTunes now gives an error with the CD/DVD drive and needs to be re-installed.
I have installed all updates for Vista, Dell support says it's an iTunes problem.
Any Ideas. Would like to import CD's into iTune and not have any errors.

Hello Bob,
Thank you for using Apple Support Communites.
If your optical drive is no longer recognized after installing iTunes, you can try the steps in this article to resolve the issue:
iTunes for Windows: Optical drive is no longer recognized, or "Disc burner or software not found" alert after install - Apple Support
Regards,
Jeff D.

DVD drive not recognized after Security update

Hello -
Well, for whatever reason I decided to apply some Apple software updates today. I repaired permissions, did a back up to an external Firewire drive with SuperDuper and downloaded several packages - iDVD 6.0.2, iMovie 6.0.2, Quicktime 7.1, iPhoto 6.0.3, iWeb 1.1, and Security Update 2006-003. I installed the Security Update and rebooted. I had read about an issue with DVDs, so promptly inserted a DVD-R disc of mine with a movie on it (not a commercial DVD, footage I had shot on my own). It was not recognized. I restarted with the mouse button held, no luck. I repaired permissions, no change.
I restarted from the backup on the external drive and cloned the backup over to my Powerbook. The problem did not go away, there the DVD sits, unrecognized. Tried to see if DVD player would see the DVD, got a message "There was an initialization error. A valid DVD drive could not be found [-70012]" disc burning in System profiler says no burning device was found. Tried to re-install DVD player via 4.6.1 update, got a message "Compatible DVD hardware was not detected, installation will not proceed".
Where to next? I haven't booted into open firmware to try to eject the disk that way, but one post on the discussions here somewhere had no luck. I'd really rather not erase and re-install and migrate from my back-up, but if that is all that's left, ok. Thanks for your help.
BTW, 10.4.6 ona 1.5 GHz Al PowerBook with 2GB RAM, not original RAM but Samsung from OWC. Thanks again.

Well, one thing I had not tried was to reset PRAM//NVRAM. I combined that step with shutting down, unplugging the power cord and letting it sit for 15 minutes. Reconnected power, restarted while holding cmd-option-P-R through the second start-up chime, and viola, my DVD appears on the desktop, the drive is listing in the system profiler, problem gone. Thanks all for the rapid responses.
Darth

DVDs Are Not Recognized

I updated my PowerMac (2.0GHz G5, 3GB RAM, LaCie dual-layer DVD burner) to 10.5.6. I tried burning a DVD (copied from a VHS tape and converted to a VIDEO_TS folder, and burned via Toast), and everything was fine, but it crashed halfway through burning the DVD. That's happened before (ever since switchig to Leopard), but not recently. So, I put in another DVD+R and the same thing happened. So, I restarted the machine, and now it won't even recognize that there's a disk in the drive.
So, I powered down and restarted the machine and the same thing happens. I also tried DVD+R DL, and they're not recognized, either. I haven't tried putting in a DVD movie yet, though.
Any ideas?
TIA

Thanks for the replies.
I tried to mount blank DVD-R and DVD+R discs with sudo mount /dev/sr0 /mnt/CD.
I keep getting the answer: mount: no medium found on /dev/sr0.
On some discs it returns with:
mount: wrong fs type, bad option, bad superblock on /dev/sr0,
missing codepage or helper program, or other error
In some cases useful info is found in syslog - try
dmesg | tail or so.
but I have not been able to find a pattern for when it will do this.
I ran smartctl -T permissive -i /dev/sr0 with a disc in the drive and got this response:
=== START OF INFORMATION SECTION ===
Vendor: MATSHITA
Product: DVD-RAM UJ-832
Revision: 1.00
Device type: CD/DVD
Local Time is: Fri Jan 31 06:18:51 2014
device Test Unit Ready [medium or hardware error (serious)]
SMART support is: Available - device has SMART capability.
SMART support is: Disabled
Temperature Warning: Disabled or Not Supported
My first thought is that the two thinkwiki pages that I posted have links to firmware updates far past 1.00. However, I still can't tell which drive I have.

Mac DVD Superdrive not recognized in Encore CS5

I'm trying to burn a DVD using Encore CS5 on my new Mac Pro. I already spoke with Apple to troubleshoot to see if it was the drive. It was not the drive. Therefore, there is a problem with Encore not recognizing the drive. In the destination window in Encore, where it says "Recorder" in the build tab, it says "None Found". Anyone know what the problem is?

Well, in the WINDOWS world some software will cause Encore to not be able to "see" a drive, so read the links below... I don't know if the same kind of thing happens in the MAC world
Things and Software to AVOID when authoring/burning a DVD
Start --> http://forums.adobe.com/thread/608660?tstart=0
#2 here has WHY Explained http://forums.adobe.com/thread/607390
Plus http://forums.adobe.com/thread/562941?tstart=0
Again in the Windows world, if the user can't or won't remove the offending software for some reason, the solution is to have Encore build the project to hard disk (folder or create an ISO) and then use 3rd party software to burn the folder or ISO to DVD
Added
In fact, just go ahead and tell Encore to write the project to your hard drive and then use other software to write that output to a DVD... if that works, you know that "something" is getting in the way of Encore being able to communicate with your drive

DVD-Rs not recognized

My Memorex DVD-Rs are not recognized as being recordable... in otherwords in the disk Utility, it says that there is a 0 capacity.
All options in the Disk Utility are disabled.
There is an insert in the spool about firmware upgrades...
Do I really need this upgrade? Or is there something else I can do?
Macbook Mac OS X (10.4.8)

Hi Magicpixie,
Welcome to apple forum,
Is that only memorex or other brand also having similar problem?
Have you managed to burn with any other media or with that memorex before?
Actually that is normal, and you cannot make asumption it won't record by looking into disk utility, because the media is still blank and unformatted.
Try this:
Go to system preference > cd & DVDs > when you insert blank DVD > open finder > as soon as the disk icon appears:
Try to drag any files you want to burn and after that drag the dvd to the trash (it will changed into burning icon and it will burn).
Good Luck.

New Pioneer DVD drive not recognized in profiler

I have used these forums many times to solve my problems so a big thanks to everyone who contributes. I've never had to actually ask a specific questions until now so here goes....
I have an e-mac running 10.3.9. My superdrive started to get flakey (not recognizing some DVD's, spitting them out, etc.). I followed all the advice here but no luck so I finally replaced the original drive with a Pioneer DVR-118. My problems still exist and the system profiler is telling me I have a Pioneer DVR-106. Did I do something wrong on the install? Shouldn't the profiler recognize the new drive?
A big thank you to anyone who can help me through this.

Since your computer's Apple Hardware Test is on a disc and the built-in optical
drive won't work, you may have to see if an external optical drive capable of
being used as a boot, is available. This of course would be a FireWire combo
type drive that can read & write DVD & CD media and boot Macs.
You may have to see if you can archive anything worth saving from that eMac
and put it on media via another computer; if the eMac can be booted into
Target Disk Mode where it is seen by another computer as a FireWire drive.
In fact, you could see (in a reverse scenario, perhaps?) if another computer's
optical drive could be used by your eMac, if a second healthy computer is
available & then boot it into FireWire Target Disk Mode to see if you can use
the optical drive in there as though it were a peripheral. - This may not work.
I've not had to really use FireWire Target Disk Mode, but do have cables,
and an externally enclosed LaCie FW HDD which is partitioned for clones.
There are times where a FireWire externally enclosed superdrive is handy.
There may be some damage on the logic board or some circuit that does the
controlling of ATA devices on one of the buses in the computer. That would
be a possible cause of the issue. If the identity of this drive can be changed
by the user before it is installed, be sure that is set correctly for use in eMacs.
{The three eMacs I've owned, had issues early on and I got rid of them in mere
days of first purchase; at considerable distance and effort by me. Then I got
an iMac which was an unholy terror to debug after an 'authorized service' ctr
did their best to kill logic boards and sell me defective store-brand RAM they
were authorized to install in a place I was not. ThreeThousand Miles and Six
Months later, I finally got my iMac back, repaired. Only because Apple told
them to read my test notes - & just install the parts I said it originally needed.}
Do you have a second Mac nearby (presuming yes, and using it online) which
may be used to attempta further diagnostic or testing of the eMac?
Not sure if an Apple Hardware Test would be sufficient to tell the issues in
your computer; if you have a way to make use of it via external FW. Hope-
fully someone with more extensive eMac and drive experience will advise.
Good luck & happy computing!

Previously burned DVD's not recognized

Similar Messages

Maybe you are looking for