PRI card support for analog/didgiatl calls

In Cisco 2621XM, I want to install a PRI card which can receive/accept analog as well as digital calls

Hi Jassi,
You can use the follwong modules for your requirement
T1 PRI/CAS
E1 PRI/CAS
FXO
FXS
E&M
But you require minimum Cisco IOS 12.2(8)T IOS version.
Regards
PSM

Similar Messages

Support for Skype Number Calling ID Australia

Hi there
So I was wondering if there will be any support for skype number calling id in the future in australia. It is quite frustrating not having any support for ksype calling id in australia. Was wondering when support will become availible. I'm sure many of you are also feeling my pain. You pay enough for the number so you should be able to have the number as the out going caller id.
Thanks.

When will we be able to use the Skype supplied number for CID (Caller ID) in Australia?
I've been trying to get a straight answer for this for over 3 years. The closest I had was that the system can only verify the owner of a number by sending an SMS to it. Well, if Skype supplies the number in the first place they already have me validated!
Given that a mobile number can be used in Australia already why can't the Skype number be put into place?
Can a moderator or support staff please comment here?
Thank you. Daymo.

To create Trunk Group with differnt T1 PRI's groups for our outbound calls

Hi All,
I would like to request all of you that I have requiremnt that we have to create "Trunk Group" of diffenent T1 controller PRI's for outbonds call, mean I need to create a trunk group with differnt T1 PRI's groups for our outbond calls, but my problem is that I don't know and no idea that how I will do this , i am also try to find some cisco doc for this still I did not find these info, so I request all of you that I will be thank full to all of you if you can help me out for my this problems.
Thanks
Rizwan

Here is a good write up, there are many others:
http://www.markholloway.com/blog/?p=452
HTH,
Chris

GE cards supported for port- vlan based EoMPLS on 7600/sup720

Hi,
Can anyone explain/point where I can find de proper documentation where I can find the support for port- vlan based EoMPLS support cards on a 7600 with a sup720 engine on the CCO site ?
WHich GE port cards are supporting EoMPLS and which GE cards will support it not.

try
www.cisco.com/go/fn
-Waris

SDXC card support for cRIO 9031 Linux Real Time

The cRIO9031 with Linux Real Time did not support SDXC cards. Only SDGC with a maximum of 32GB supported by cRIO.
For logging application their is a need for more than 32GB => use of SDXC cards with 128/256 GB

Hi Schott,
Unfortunately, Linux does not have native (in kernel source) support for the exFAT filesystem (required for a device to be labled SDXC). As soon as such a filesystem is supported in Linux, we can enable direct support for exFAT.
In the meantime, there is nothing preventing you from formatting the card in a filesystem type that is supported on the target. FAT32 is unfortunately the most portable, accessible format, of course if you don't need to access the contents of the card from a Windows machine, you can use some of the tools on the RT controller to format the card in a more robust, journalling filesystem such as EXT4.

Cisco 8841 support for 3rd party call control

Hi Cisco Team,
What is required to get Cisco 8841 IP phone configured as a SIP phone for 3rd party call control?

Hi,
This information would be dependent on which third party you are integrating with, they should provide details of settings needed for the same. For supporting third party SIP endpoints with Cisco there are numerous docs / posts , but in your case the scenario is reverse.
HTH
Manish

Need Support for Palm Pre Call Waiting

I've had my palm pre for a month about now and notice a number of issues with its call waiting feature that need to be addressed. Here is the list:
1) I can't drop 1 call without dropping the other call: this means that if I'm on the phone with person "A" and receive a call from person "B", though I can switch between the two easily enough, I can't end the call between person "A" to talk to person "B". What's even worse, even if person "A" hangs up, the pre still keeps the call connected until I hang up my phone. This is a serious issue when you're calling outside of any promotional time, nights, or weekends.
2) in a conference call, I can't end one conversation without ending both conversation. So again, if I have both person "A" and person "B" on a call and I connect them through a conference call on my pre, I can't end the conversation with one without ending it with the other. A real pain in the butt.
I just want to know two things asap since I know this is something that'll take time to resolve (if it can be resolved)
1) is this a hardware issue or a operating system issue?
2) does conference calling really kill my minutes the way it look like it does? I'm leaning toward yes from evidence I have, but I'd like to hear it from the pre reps.
Post relates to: Pre p100eww (Sprint)

1. This functionality sometimes works and sometimes it does not. But can you answer the other part of the post. The PALM pre give the user no one to drop the other call. Mine is worse. If the other user hangs up CONFERENCE is still there; If they hang up I'm not in a CONFERENCE but the PRE does not recognize this state at all. Therefore you can't add another person to the call again.
2. This one does not affect me as much since I have the simply everything plan. But I would def. pay attentiont my bill and complain to SPRINT every time this occurs.
3. HAS ANYONE OPENED A TICKET WITH PALM FOR THE CONFERENCE CALL / CALL WAITING ISSUE?

Is this card supported for 3d ray tracing optimized with CUDA?

On the system requirements list for after effects CS6, the 660 is not listed, but I just wanted to double check. According to nvidia's website the 660 supports CUDA optimized functions. There is also the fact that sometimes softwares fail to keep up to date with what hardware works. Is this one of those case?

For a list of supported hardware acceleration cards start at http://forums.adobe.com/thread/773101 and click the system requirements link
Most nVidia cards that are not in the list may be used for hardware MPE if they have at least 1Gig of video ram, by means of the hack http://forums.adobe.com/thread/629557

Line Cards support for SupEngine 7

Hi,
I would like to upgrade my 4507 core switch which currently has Sup IV to Sup7.
the core switch currently has classic line cards WS-x4506-GB-T and WS-x4224-RJ45V and my worry is these May not be supported..
The datasheet list these as part of the supported classic cards but I would wish to get a confirmation that this is indeed so and what issues I should expect? please advise...
Sent from Cisco Technical Support iPad App

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
Line cards shouldn't be an issue. (Don't recall us bumping into any line cards issues with the sup7.)
You may need to upgrade your chassis, though.

BCM43227 Wlan Card Support for x230t?

Hi, everyone. I have a thinkpad x230t and recently changed my OS so I need to replace my WLAN card because there's no driver for intel cards.
I checked Lenovo documents, here http://download.lenovo.com/parts/ThinkPad/x230t_fru_bom_20140421.pdf
it says BCM43227 card with FRU number 03T9015 is supported so I made my purchase online. But upon boot on it gives me 1802 error saying it's not a proved card.
The BCM43227 card I have has ID/DEV numbers: 14E4/4358/14E4/0543. I assume it's the same card mentioned in the pdf. I have bios version 2.55, will updating bios solve this problem?
Did anyone have experience with this card? Please help!

Hi, George:
Thank you for your reply!
The seller who sold me this card claims it is the same product as 03T9015, it's just Lenovo makes different lables during different periods. I compared this card with 03T9015 pictures online and they appear to have the same Lenovo P/N number and the same Cyber Tan P/N number. But the card I have is mssing the FRU numbers. I'm attaching pictures of both.
My questions are:
1. Is my card realy 03T9015?
2. If this is not, will a real 03T9015 pass the whitelist check?
To my understanding, the way whitelist works is to check the card's Dev/Ven and Sub Dev/Ven numbers. Can someone who has 03T9015 post his/her numbers so I can compare with the one I have?
Moderator note; picture(s) converted to link(s) About Posting Pictures In The Forums

MicroSD card support for 808 PureView an Nokia N8-...

Hello community,
this is just an Information from my personal experience.
Yesterday I bought a 808 PureView and inserted a Sandisk Ultra Class 10 micro SD with UHS-I.
http://www.amazon.de/dp/B007JTKLEK
This memory card does not work with Symbian Belle Feature Pack 1 Software Version 112.020.0311 which is dated 2012-06-26. The same micro SD card does work very well in my Nokia N8-00 with Symbian BelleRefresh Software Version 111.040.1511 dated 2012-07-28.
I'm currently investigating which high speed 32GB micro SD will work in the Nokia 808 PureView.
Wolfgang
Wolfgang Exler
Stuttgart, Germany
Solved!
Go to Solution.

@Wolfgang_Exter
Using Sandisk 32GB Class 4 microSDHC in 808 without issue, although Class 6 advised for recording HD video.
Happy to have helped forum with a Support Ratio = 42.5

"Multicast" support for EJB-EJB calls to cluster

What I have to work with:
+ WebLogic Server 5.1 cluster
+ Stateless session EJBs
What I want to do:
+ Be able to know list of available servers in the cluster
and use this list to broadcast same information to all EJBs
with same name in cluster
+ I understand that the cluster-aware EJB stub has this list
when a client gets a home reference to the EJB Object
+ I have not seen any specific WebLogic API to get this list
either by accessing the cluster-aware JNDI table or the
cluster-aware EJB stub.
+ Othwerwise, I would then need to implement my own server
list manager to get this list. Such task should not be that difficult.
Why I want to do the above:
+ I would like to implement a EJB sendAll() method that will
send the same request to all EJBs of the same JNDI name in the cluster.
+ Please correct me if I am wrong but I have not seen anywhere
in the WebLogic 5.1 documentation regarding the automatic multicast
ability of broadcasting EJBs calls via EJB-to-EJB communication to a
cluster.
+ I understand that multicasting is only used internally, ie,
heartbeats.
Plus, I believe that RMI does not support multicasting.

I'd like to hear a bit more about what you are trying to do. (at a
higher level)
RMI / EJB is a point-to-point model. A client is making an RMI call to
a server. Granted, in our clustering solution, there may not be one
physical server, but the idea is to give the appearance of one big,
reliable server.
-- Rob
Ren Bitonio wrote:
>
What I have to work with:
+ WebLogic Server 5.1 cluster
+ Stateless session EJBs
What I want to do:
+ Be able to know list of available servers in the cluster
and use this list to broadcast same information to all EJBs
with same name in cluster
+ I understand that the cluster-aware EJB stub has this list
when a client gets a home reference to the EJB Object
+ I have not seen any specific WebLogic API to get this list
either by accessing the cluster-aware JNDI table or the
cluster-aware EJB stub.
+ Othwerwise, I would then need to implement my own server
list manager to get this list. Such task should not be that difficult.
Why I want to do the above:
+ I would like to implement a EJB sendAll() method that will
send the same request to all EJBs of the same JNDI name in the cluster.
+ Please correct me if I am wrong but I have not seen anywhere
in the WebLogic 5.1 documentation regarding the automatic multicast
ability of broadcasting EJBs calls via EJB-to-EJB communication to a
cluster.
+ I understand that multicasting is only used internally, ie,
heartbeats.
Plus, I believe that RMI does not support multicasting.--
Coming Soon: Building J2EE Applications & BEA WebLogic Server
by Michael Girdley, Rob Woollen, and Sandra Emerson
http://learnweblogic.com

Graphic Card Support for pm9m-v

I was wondering if anyone could tell me what graphic cards my motherboard supports as i am about to purchase one. It is an msi pm9m-v running on win 7 with 1gb rddr ram.
Thanx

Wonkanoby is right. The only option would be a PCI Video Card. Forget about PCI Express and/or AGP cards.
Probably best to stick with onboard video.

6GB MicroSD Card support for E90??

Hi,
Possible to run 6GB MicroSD card on E90 communicator??Please kindly advise.Thanks!
E90 Communicator V 07.40.1.2!!

Oh Great! Thanks alot guys!Appreciate the advise.Guess I will upgrade my external memory on E90
E90 Communicator V 07.40.1.2!!

PETITION FOR 4GB CARD SUPPORT!

Hello...
Nokia Users please join this petition for 4GB Card Support for Recent Nokia Phones & Upcoming New Nokia Phones!
Im sure there are owners out there who want the support of 4GB Card. Why is Nokia so Pathetic at listening to our concerns?
Its all simple! the recent models just need firmware teaking (update) so it support 3rd Party Memory Cards! We should benefit this feature from out phones. Theres no such thing as EXTRA hardware required to support 4GB Card ie 4GB Mini-SD, becuase it is the same dimensions n connections & all it needs is Firmware Update!.
However N-Gage, 6280 supports 4GB Card & there were sum screenshots of N80 working with 4GB Card using the old firmware v3.xx.x.xx
Nokia are so pathetic they lock the firmware by not allowing 100% compatible support for 3rd Party cards only Nokia branded Cards!
ALL WE WANT!...
However we (all nokia onwers) should have our phones supporting 4GB Cards. So uwners who agree please post your comment as i will forward this to Nokia Team. Its about time they took action to this!
If you find my post useful then click on
Kudos!Nokia N96 (v20.050 / RM-247)
www.shaysoft.net | Competitions!

hello,
i have an n80 ie, and at the moment i´ve a 2gb mini-sd, formated with >>>>FAT32 working in it.
At this site /discussions/board/message?board.id=smartphones&message.id=38078 , "shayesta", says, if you format your 4gb-mini-sd in your mobile, it will work. THIS IS NOT TRUE (maybe it depends on fw, but excluding the old 3.xxx , i dont believe at this moment in this.
I´ve buyed a 4gb mini-sd (NON-HC!!) ,when i try to format it in my n80ie, it says: "memory-card faulty".
When i use the 4gb-card in my pc or in my qtek9100 (mda vario) it works very well!
It may be paranoid, but i think nokia build a limitation in fw, so that u can´t use more than 2gb mem, because they want that we buy early a new mobile, that sopport 4gb officially. And probably with sup. for "sd-hc" , what on the other hand costs extra money for the "hc"(NON-HC WORX WITH FAT32 TOO, so thats not the difference!)
FACT IS, the n80 CAN work with 4gb, but nokia barricades this function. (I bet every n-series mobile could work since a year with 4gb-card if nokia wouldn´t be so obsinate).
I have not much hope for this great "4gb" fw-upgrade, but i wish the best.
so long, greetz (sry for my bad english, i´m a man from ger, german)
EDIT: removed retail link - MohjoMessage Edited by mohjo on 22-May-2007 04:02 PM

PRI card support for analog/didgiatl calls

Similar Messages

Maybe you are looking for