Primary ASA unit fails due to IPS

Hello there,
We have Active/Standy ASA units with SSM-20 IPS modules. Everytime the Primary ASA unit gets failed and a switchover is triggered. As a result, Secondary becomes active and Primary becomes standy failed.
I upgraded IPS firmware to the latest one, I then changed both Primary ASA unit along with IPS module. But the issue still persists.
I have provided proper earth and power.
Thanks in advance.

Hi,
To start with, can you paste the following from the two ASA's:
- show failover history
- show failover
- show module 1 detail
- show run failover
- Syslogs from the instant when failover occured if available.
I will review these and let you know if more outputs are needed to figure out the root cause.
Sourav

Similar Messages

Replacement of primary unit failed! (ASA5510 active/standby)

Hi all,
I have an issue bringing up my RMA'd primary ASA unit.
So what happened so far:
1. primary unit failed
2. secondary took over and is now secondary - active (as per sh fail)
2. requested RMA at Cisco
3. got ASA and checked that Lic (SSL), OS (8.2.2) and ASDM are at the same level as the secondary
4. issued wr erase and reloaded
5. copied the following commands to the new (RMA) primary unit:
failover lan unit primary
failover lan interface Failover Ethernet3
failover interface ip Failover 172.x.x.9 255.255.255.248 standby 172.x.x.10
int eth3
no shut
failover
wr mem
6. installed primary unit into rack
7. plugged-in all cables (network, failover, console and power)
8. fired up the primary unit
9. expected that the unit shows:
Detected an Active mate
Beginning configuration replication from mate.
End configuration replication from mate.
10. but nothing happened on primary unit
So can anyone give me assistance on what is a valid and viable approach in replacing a failed primary unit? Is there a missing step that hinders me to successfully replicate the secondary - active config to the primary - standby unit.
I was looking for help on the net but unfortunately I was not able to find anything related to ASA55xx primary unit replacement with a clear guideline or step by step instructions.
Any comments or suggestions are appreciated, and might help others who are in the same situation.
Thanks,
Nico

Hi Varun,
Thanks for catching-up this thread.
Here you go:
sh run fail on secondary - active:
failover
failover lan unit secondary
failover lan interface Failover Ethernet0/3
failover key *****
failover link Failover Ethernet0/3
failover interface ip Failover 172.x.x.9 255.255.255.248 standby 172.x.x.10
sh fail hist on secondary - active:
asa1# sh fail hist
==========================================================================
From State                 To State                   Reason
==========================================================================
23:47:15 CEST Feb 19 2011
Not Detected               Negotiation                No Error
23:47:19 CEST Feb 19 2011
Negotiation                Cold Standby               Detected an Active mate
23:47:21 CEST Feb 19 2011
Cold Standby               Sync Config                Detected an Active mate
23:47:36 CEST Feb 19 2011
Sync Config                Sync File System           Detected an Active mate
23:47:36 CEST Feb 19 2011
Sync File System           Bulk Sync                  Detected an Active mate
23:47:50 CEST Feb 19 2011
Bulk Sync                  Standby Ready              Detected an Active mate
10:34:09 CEDT Sep 3 2011
Standby Ready              Just Active                HELLO not heard from mate
10:34:09 CEDT Sep 3 2011
Just Active                Active Drain               HELLO not heard from mate
10:34:09 CEDT Sep 3 2011
Active Drain               Active Applying Config     HELLO not heard from mate
10:34:09 CEDT Sep 3 2011
Active Applying Config     Active Config Applied      HELLO not heard from mate
10:34:09 CEDT Sep 3 2011
Active Config Applied      Active                     HELLO not heard from mate
==========================================================================
sh fail on secondary - active
asa1# show fail
Failover On
Failover unit Secondary
Failover LAN Interface: Failover Ethernet0/3 (up)
Unit Poll frequency 1 seconds, holdtime 15 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 2 of 110 maximum
Version: Ours 8.2(2), Mate 8.2(2)
Last Failover at: 10:34:09 CEDT Sep 3 2011
        This host: Secondary - Active
                Active time: 441832 (sec)
                slot 0: ASA5510 hw/sw rev (2.0/8.2(2)) status (Up Sys)
                  Interface Outside (x.x.x.14): Normal (Waiting)
                  Interface Inside (x.x.x.11): Normal (Waiting)
                slot 1: empty
        Other host: Primary - Failed
                Active time: 40497504 (sec)
                slot 0: ASA5510 hw/sw rev (2.0/8.2(2)) status (Unknown/Unknown)
                  Interface Outside (x.x.x.15): Unknown
                  Interface Inside (x.x.x.12): Unknown
                slot 1: empty
Stateful Failover Logical Update Statistics
        Link : Failover Ethernet0/3 (up)
        Stateful Obj    xmit       xerr       rcv        rerr
        General         2250212    0          64800624   309
        sys cmd         2250212    0          2249932    0
        up time         0          0          0          0
        RPC services    0          0          0          0
        TCP conn        0          0          46402635   309
        UDP conn        0          0          21248      0
        ARP tbl         0          0          15921639   0
        Xlate_Timeout   0          0          0          0
        IPv6 ND tbl     0          0          0          0
        VPN IKE upd     0          0          96977      0
        VPN IPSEC upd   0          0          108174     0
        VPN CTCP upd    0          0          19         0
        VPN SDI upd     0          0          0          0
        VPN DHCP upd    0          0          0          0
        SIP Session     0          0          0          0
        Logical Update Queue Information
                        Cur     Max     Total
        Recv Q:         0       17      203259096
        Xmit Q:         0       1       2250212
show ver on secondary - active
asa1# sh ver
Cisco Adaptive Security Appliance Software Version 8.2(2)
Device Manager Version 6.2(5)53
Compiled on Mon 11-Jan-10 14:19 by builders
System image file is "disk0:/asa822-k8.bin"
Config file at boot was "startup-config"
asa1 up 200 days 12 hours
failover cluster up 1 year 108 days
Hardware:   ASA5510, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
Slot 1: ATA Compact Flash, 64MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
                             Boot microcode   : CN1000-MC-BOOT-2.00
                             SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
                             IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04
0: Ext: Ethernet0/0         : address is 0022.55cf.7420, irq 9
1: Ext: Ethernet0/1         : address is 0022.55cf.7421, irq 9
2: Ext: Ethernet0/2         : address is 0022.55cf.7422, irq 9
3: Ext: Ethernet0/3         : address is 0022.55cf.7423, irq 9
4: Ext: Management0/0       : address is 0022.55cf.741f, irq 11
5: Int: Not used            : irq 11
6: Int: Not used            : irq 5
Licensed features for this platform:
Maximum Physical Interfaces    : Unlimited
Maximum VLANs                  : 100
Inside Hosts                   : Unlimited
Failover                       : Active/Active
VPN-DES                        : Enabled
VPN-3DES-AES                   : Enabled
Security Contexts              : 2
GTP/GPRS                       : Disabled
SSL VPN Peers                  : 10
Total VPN Peers                : 250
Shared License                 : Disabled
AnyConnect for Mobile          : Disabled
AnyConnect for Cisco VPN Phone : Disabled
AnyConnect Essentials          : Disabled
Advanced Endpoint Assessment   : Disabled
UC Phone Proxy Sessions        : 2
Total UC Proxy Sessions        : 2
Botnet Traffic Filter          : Disabled
This platform has an ASA 5510 Security Plus license.
Serial Number: xxx
Running Activation Key:xxxx
Configuration register is 0x1
Configuration last modified by enable_1 at 10:05:32.149 CEDT Fri Jul 15 2011

LabVIEW FPGA: The compilation failed due to a xilinx error

I'm getting a "Compilation failed due to Xilinx error" trying to compile code in LabVIEW 2013.The code had compilated successfully in labview2012. Any suggestions on what is causing this issue?
Details:
ERROR:HDLCompiler:432 - "C:\NIFPGA\jobs\THY4t7n_z6im2K7\NiFpgaAG_0000003a_SequenceFrame.vhd" Line 29: Formal <cparametersignal> has no actual or default value.
INFO:HDLCompiler:1408 - "C:\NIFPGA\jobs\THY4t7n_z6im2K7\NiFpgaSetOutputDataEnable.vhd" Line 37. cparametersignal is declared here
ERROR:HDLCompiler:854 - "C:\NIFPGA\jobs\THY4t7n_z6im2K7\NiFpgaAG_0000003a_SequenceFrame.vhd" Line 21: Unit <vhdl_labview> ignored due to previous errors.
VHDL file C:\NIFPGA\jobs\THY4t7n_z6im2K7\NiFpgaAG_0000003a_SequenceFrame.vhd ignored due to errors
-->
Total memory usage is 204688 kilobytes
Number of errors : 2 ( 0 filtered)
Number of warnings : 4 ( 0 filtered)
Number of infos : 0 ( 0 filtered)
Process "Synthesize - XST" failed
Compilation Time
Date submitted: 2014/2/26 18:15
Date results were retrieved: 2014/2/26 18:17
Time waiting in queue: 00:06
Time compiling: 02:02
- PlanAhead: 01:16
- Core Generator: 00:00
- Synthesis - Xst: 00:35
Solved!
Go to Solution.

I have got the same error, Have you solved this error?
What you have done?
jasonneu wrote:
I'm getting a "Compilation failed due to Xilinx error" trying to compile code in LabVIEW 2013.The code had compilated successfully in labview2012. Any suggestions on what is causing this issue?
Details:
ERROR:HDLCompiler:432 - "C:\NIFPGA\jobs\THY4t7n_z6im2K7\NiFpgaAG_0000003a_SequenceFrame.vhd" Line 29: Formal <cparametersignal> has no actual or default value.
INFO:HDLCompiler:1408 - "C:\NIFPGA\jobs\THY4t7n_z6im2K7\NiFpgaSetOutputDataEnable.vhd" Line 37. cparametersignal is declared here
ERROR:HDLCompiler:854 - "C:\NIFPGA\jobs\THY4t7n_z6im2K7\NiFpgaAG_0000003a_SequenceFrame.vhd" Line 21: Unit <vhdl_labview> ignored due to previous errors.
VHDL file C:\NIFPGA\jobs\THY4t7n_z6im2K7\NiFpgaAG_0000003a_SequenceFrame.vhd ignored due to errors
-->
Total memory usage is 204688 kilobytes
Number of errors : 2 ( 0 filtered)
Number of warnings : 4 ( 0 filtered)
Number of infos : 0 ( 0 filtered)
Process "Synthesize - XST" failed
Compilation Time
Date submitted: 2014/2/26 18:15
Date results were retrieved: 2014/2/26 18:17
Time waiting in queue: 00:06
Time compiling: 02:02
- PlanAhead: 01:16
- Core Generator: 00:00
- Synthesis - Xst: 00:35
Mahran

Hub startup failed due to licensing failure

Hi all.
I have just installed weblogic 6.0 sp1 on solaris 2.8. the web server starts
up and everything is hunky dory.
furthermore i downloaded collaborate 1.0.1 and installed it. the
installation went fine.
here is my problem. when i execute the startWeblogic.sh script in the hub,
Weblogic reports the following error:
<24-Apr-01 13:49:03 GMT+01:00> <Error> <WLC> <<Hub> ERROR: Hub startup
failed due to licensing failure.>
I get this problem using jdk122 and jdk130.
I cannot seem to find the problem.
Any feedback would be appreciated.
PS. My license.bea file looks as follows:
<?xml version="1.0"?>
<bea-licenses>
<license-group format="1.0" product="WebLogic Collaborate"
release="1.0">
<license
component="Core Server"
expiration="2001-05-24"
ip="any"
licensee="BEA Evaluation Customer"
type="EVAL"
signature="2tDDH3g1qXubdlfsahWRNrR6+tc=0MC0CFCoH/XUHiZuu+yhzpuzv6UFl
kJ44AhUA2/U26g1keq5nNoO00NC2u9ezWeA="
/>
</license-group>
<license-group format="1.0" product="wlpi" release="1.2">
<license
component="WebLogic Process Integrator"
expiration="2001-05-24"
ip="any"
licensee="BEA Evaluation Customer"
type="EVAL"
users="5"
signature="2tDDH3g1qXubdlfsahWRNrR6+tc=0MCwCFEh5H427STpTMX1y25DSmc65
b/MVAhQMNJo1ujoB6DudzF59hL/Tx2vbGQ=="
/>
</license-group>
<license
component="WebLogic"
expiration="2001-05-23"
ip="any"
licensee="BEA Evaluation Customer"
type="EVAL"
units="5"
signature="OFcm7oSc4jOT5vonluVZpsAHX2g=0MCwCFEmkcBweXEoxtJxzCIarx8i+
XBguAhQvCxM9E/T4HGfbIUfb4+OiNUYsPw=="
/>
<license
component="SSL/Export"
expiration="2001-05-23"
ip="any"
licensee="BEA Evaluation Customer"
type="EVAL"
units="5"
signature="OgS8PvglCrGr5xglLHeut8tE5vc=0MC0CFQDcxuNftALK3tZYuJw6hI15
GaqrBgIUcTi0vNzwoG1alTX1WXnvcX9EOiM="
/>
<license
component="2PC"
expiration="2001-05-23"
ip="any"
licensee="BEA Evaluation Customer"
type="EVAL"
units="5"
signature="CcdspC/3P0iELwWsETBWI/hEalw=0MC0CFQCtTlW7enw3kFZ7IU09jaa/
BVle5wIUSSfMk23C19hznredmfr+soEYiX0="
/>
<license
component="In-memory Replication - Servlet"
expiration="2001-05-23"
ip="any"
licensee="BEA Evaluation Customer"
type="EVAL"
units="5"
signature="c+mtrQ1ZuRiKeiELua/hSxvHqew=0MC4CFQC4qvLRsblTBvC5+IEVrDI1
Tek1YwIVAJ1NYWZE6xPHYyyVdlaXRJbhayCj"
/>
<license
component="In-memory Replication - EJB"
expiration="2001-05-23"
ip="any"
licensee="BEA Evaluation Customer"
type="EVAL"
units="5"
signature="ZenJ1bPXGf2N/Bq8XugDnDIP8sQ=0MC0CFQC+ayYQFxhpIMug7ZHtZIfS
vg4tlwIUHIYgx30GoxIdmR19cGddWM/mp3E="
/>
<license
component="EJB 1.1"
expiration="2001-05-23"
ip="any"
licensee="BEA Evaluation Customer"
type="EVAL"
units="5"
signature="XwwhoY5ysJ8h1pjzx23ujxZI9nY=0MC4CFQC2ATLeRv6cStQE1B/gyMUT
R6SRvQIVAMsQmtFC0/J4sF26n+B1zEyDOmv/"
/>
<license
component="EJB 2.0"
expiration="2001-05-23"
ip="any"
licensee="BEA Evaluation Customer"
units="5"
signature="ksI9jkE6gL9u8GdVEpZNQtOvjm8=0MCwCFBUir1rQV/FLNdc+4lfdIV1x
+xk5AhQpQwwWMfUd6TbL3UvB0u9DbZponQ=="
/>
<license
component="JMS"
expiration="2001-05-23"
ip="any"
licensee="BEA Evaluation Customer"
type="EVAL"
units="5"
signature="Z4Q4VngOAJSqSsr1UXC37DTOyVg=0MC0CFQCZtOwzb02hOSR3z9Hp6k86
nl1uFQIUfhy+ODL+Y7B9DkGDS7yT4zQPPpE="
/>
<license
component="Cluster"
expiration="2001-05-23"
ip="any"
licensee="BEA Evaluation Customer"
type="EVAL"
units="5"
signature="Tkg9CGjEik3MbkFmi6rPsSiO0J0=0MC0CFEAV5hPKLVSgV8YoeCEVu5m7
5ktkAhUA2lBI0PwiMigvK1E/pVS0vqmsy3w="
/>
<license
component="Clustered JMS"
expiration="2001-05-23"
ip="any"
licensee="BEA Evaluation Customer"
type="EVAL"
units="5"
signature="nEpfLZwWyM4Bo7UZZHE4hQgntMc=0MCwCFBKYtPvqZE18JdGBvU6cZomM
xW1cAhR3moJKg7FHMxvsZphQz5jVCahrfA=="
/>
<license
component="jDriver/MSSQLServer4"
expiration="2001-05-23"
ip="any"
licensee="BEA Evaluation Customer"
type="EVAL"
units="5"
signature="Dgw2DzDWyBNob6pJunUY1Xoz7c8=0MC0CFQC4PKj8UFoC3J0XuC7pmzRL
TtgP8QIUAhJF5DuvZ10zvf/6mxe0Ti/rG4c="
/>
<license
component="jDriver/Informix4"
expiration="2001-05-23"
ip="any"
licensee="BEA Evaluation Customer"
type="EVAL"
units="5"
signature="6O/i8fVnKIeVwzz+e0zUMQL5uRU=0MC0CFH+NK7nnRm+Qp+qRXZdeV2yF
6YxdAhUA3vch2xTdmM5Ao+00+IOR5f3jGH0="
/>
<license
component="jDriver/Oracle"
expiration="2001-05-23"
ip="any"
licensee="BEA Evaluation Customer"
type="EVAL"
units="5"
signature="NtSVpPAloTJqBstOWKVnuh3q0H4=0MC0CFA+2ny24Zdyrb0lsL3duwfEB
9zKMAhUAqDtTbLMN3QfJWUVhJr+NBQU/x/k="
/>
</license-group>
</bea-licenses>

Gotta add listeners.ContextListener to your CLASSPATH
in Eclipse.
I don't think that package name is right. You've got
another problem besides your context XML.
%The context XML may not be the problem at all. Such tomcat errors are standard when it was unable to load required classes on startup.
The listeners all being interfaces, it's impossible to say whether it is the standard listeners or custom listener classes (regd in your web.xml) that's not being found on startup.
cheers,
ram.

EXPORT Backup failing due to character set problem

Hi ,
The export Backup failing due to character set problem
. . exporting table ravidlx
EXP-00008: ORACLE error 6552 encountered
ORA-06552: PL/SQL: Compilation unit analysis terminated
ORA-06553: PLS-553: character set name is not recognized
P
Please suggest how to set character set
Regards,
kk
Edited by: kk001 on Aug 29, 2011 7:22 PM

kk001 wrote:
Hi ,
The export Backup failing due to character set problem
. . exporting table ravidlx
EXP-00008: ORACLE error 6552 encountered
ORA-06552: PL/SQL: Compilation unit analysis terminated
ORA-06553: PLS-553: character set name is not recognized
P
Please suggest how to set character set
I don't know what you have.
I don't know what you do.
I don't know what you see.
It is really, Really, REALLY difficult to fix a problem that can not be seen.
use COPY & PASTE so we can see what you do & how Oracle responds.
do as below so we can know complete Oracle version & OS name.
Post via COPY & PASTE complete results of
SELECT * from v$version;

Cannot connect to olap service. Cannot connect to Essbase Server. Error:Essbase Error(1051293): Login fails due to invalid login credentials

Hello All,
I am getting following error, when trying to expand essbase from calculation manager, "Cannot connect to olap service. Cannot connect to Essbase Server. Error:Essbase Error(1051293): Login fails due to invalid login credentials",
I am using EPM 11.1.2.1
Thanks
Yash

If you have moved the server to a new data center and an issue has started occurring then it could point to the change.
Are you able to log into essbase directly with Maxl using the same account?
If you run a registry report do you see any of the configuration with IPs instead of DNS/hostname
Cheers
John
http://john-goodwin.blogspot.com/

Backup to remote stage failed due to RFC error

Hello!
Recently I have problem to execute a successful online Backup to the external source.
If I start backup from DB13 and analyse the work processes (Tcode SM50) I found the following:
The responsible BGD-WP:
status: On hold , reason: RFC, report: SAPLSSXP
The dev_w8 trace retrieves the following error:
Source RSCROSS10 Line 112.
Error Code DBIF_RSQL_SQL_ERROR.
Module $Id: //bas/700_REL/src/krn/runt/absapsql.c#6 $ SAP.
Function HandleRsqlErrors Line 761.
The DB13-protocol retrieves the following information:
BR0278E Command output of 'F:\usr\sap\DEV\SYS\exe\uc\NTAMD64\sapftp.exe -v -n -i 192.168.200.3 -u H:\oracle\DEV\sapbackup\.bdwkhbgq.ftp -b -c put E:\ORACLE\DEV\SAPDATA1\SR3_3\SR3.DATA3 /sap/DEVB/bdwkhbgq/SR3.DATA3':
Connected to 192.168.200.3 Port 21.
220-FTP server ready. 220 This is a private system - No anonymous login 331 User sapbackup OK. Password required 230-User sapbackup has group access to: administrator 230-This server supports FXP transfers 230-OK. Current restricted directory is / 230-************************************************ 230-* Use SITE command to change client codepage: * 230-* ie, site codepage [client codepage] * 230 ************************************************ 200 TYPE is now 8-bit binary 200 PORT command successful 150 Connecting to port 2734 NiWrite error: -6, bytes to send: 32767 bytes written: 0
BR0280I BRBACKUP time stamp: 2007-10-20 03.08.23
BR0279E Return code from 'F:\usr\sap\DEV\SYS\exe\uc\NTAMD64\sapftp.exe -v -n -i 192.168.200.3 -u H:\oracle\DEV\sapbackup\.bdwkhbgq.ftp -b -c put E:\ORACLE\DEV\SAPDATA1\SR3_3\SR3.DATA3 /sap/DEVB/bdwkhbgq/SR3.DATA3': 1
BR0222E Copying E:\ORACLE\DEV\SAPDATA1\SR3_3\SR3.DATA3 to/from /sap/DEVB/bdwkhbgq/SR3.DATA3 failed due to previous errors.
Can some one help me with this issue?
Thank you very much!
regards
Thom

Hello Eric,
unfortunately it is not possible to do it, because I have only remote access to the SAP system.
Is it possible to analyse the problem with the log files?
If yes --> which logs should I post here?
I went through the monitors in RZ20 and found a lot of errors/warning:
Database:
DBIF_SETG_SQL_ERROR
ORA-03106: fatal two-task communication protocol error
DB error 24909 in FET
SQL error 3106: WP in reconnect status
Background:
Job SAP_COLLECT_FOR_PERMONITOR terminated
Utilisation:
100% > 95% Background work process load exceeds threshold
BackgroundService: SystemWideFree BPWP: 1 WPs > 2 WPs Current value over threshold value.
Abap ErrorInUpdate
Syslog : BasisSystem
Operating system call recv failed (error no. & >E5)
The log file dev_cp retrieves the following information after execution of DB Check:
Trace file of control program (trace level 3)
< Function: BtcTrcInit> Function: main SAPXPG 700
2007-10-23--14-42-27 : Before BtcXpgDetach
> Function: BtcXpgDetach < Function: BtcXpgDetach Accept RFC connection from R/3 system
2007-10-23--14-42-27 : Before RfcAccept
2007-10-23--14-42-27 : RfcAccept returned OK
security check switched OFF
Install RFC call SAPXPG_START_XPG
Install RFC call SAPXPG_START_XPG_LONG
Install RFC call SAPXPG_END_XPG
Wait for RFC call SAPXPG_START_XPG or SAPXPG_START_XPG_LONG
2007-10-23--14-42-27 : Before first call of RFCDispatch
> Function: BtcXpgStartXpgLong
2007-10-23--14-42-27 : Beginning of BtcXpgStartXpgLong
> Function: BtcXpgStartXpgImportLong > Function: BtcXpgParam < Function: BtcXpgParam > Function: BtcXpgParam
Line Text
<No StdOut/StdErr output reported>
Target log table is not identical to source
ItGetLine terminated with NULL
<Function: BtcXpgItTransfer > Function: BtcTrcReset < Function: BtcTrcReset Call mode: VIA RF
Input arguments of BtcXpgStartXpg:
My WP settings are:
rdsip/wp_no_dia = 6
rdsip/wp_no_btc = 3
rdsip/wp_no_vb = 1
rdsip/wp_no_vb2 = 1
rdsip/wp_no_spo = 1
Thank you!
Thom

Getting error in mailing program :Cause: FDPSTP failed due to ORA-29277

in the following program i am submitting a request and sending concurrent program log file (.REQ file)as an attachment but getting
following error,plese tell me where i am wrong
ORACLE error 29277 in FDPSTP
Cause: FDPSTP failed due to ORA-29277: invalid SMTP operation
ORA-06512: at "SYS.UTL_SMTP", line 44
ORA-06512: at "SYS.UTL_SMTP", line 150
ORA-06512: at "SYS.UTL_SMTP", line 383
ORA-06512: at "SYS.UTL_SMTP", line 399
ORA-0651
code:
CREATE OR REPLACE PACKAGE BODY APPS.xx_create_acct
AS
 PROCEDURE submit_request(
 errbuf OUT VARCHAR2,
 retcode OUT VARCHAR2,
 Source_Application varchar2,
Application number,
Dummy_Parameter_0 varchar2,
Ledger number,
Process_Category varchar2,
End_Date varchar2,
Create_Accounting_Flag varchar2,
Dummy_Parameter_1 varchar2,
Accounting_Mode varchar2,
Dummy_Parameter_2 varchar2,
Errors_Only_Flag varchar2,
Report varchar2,
Transfer_to_GL_Flag varchar2,
Dummy_Parameter_3 varchar2,
Post_to_GL_Flag varchar2,
GL_Batch_Name varchar2,
Mixed_Currency_Precision Number,
Include_Zero_Amt_Lines_Flag varchar2,
Request_ID varchar2,
Entity_ID Number,
Source_Application_Name varchar2,
Application_Name varchar2,
Ledger_Name varchar2,
Process_Category_Name varchar2,
Create_Accounting varchar2,
Accounting_Mode_Name varchar2,
Errors_Only varchar2,
Report_Level varchar2,
Transfer_to_GL varchar2,
Post_in_GL varchar2,
Include_Zero_Amount_Lines varchar2,
Valuation_Method varchar2,
Security_ID_Integer_1 varchar2,
Security_ID_Integer_2 varchar2,
Security_ID_Integer_3 varchar2,
Security_ID_Char_1 varchar2,
Security_ID_Char_2 varchar2,
Security_ID_Char_3 varchar2,
Concurrent_Request_ID number,
P_INCLUDE_USER_TRX_ID_FLAG varchar2,
P_INCLUDE_USER_TRX_IDENTIFIERS varchar2,
P_DEBUG_FLAG varchar2
 IS
 l_senderemail VARCHAR2 (2000) := '[email protected]';
 l_request_id NUMBER;
 errmsg VARCHAR2 (1000);
 req_id NUMBER;
 phase VARCHAR2 (200);
 status VARCHAR2 (200);
 dphase VARCHAR2 (200);
 dstatus VARCHAR2 (200);
 MESSAGE VARCHAR2 (200);
 wait_stat BOOLEAN;
 l_file_name VARCHAR2 (200);
 l_file_path VARCHAR2 (2000);
 crlf VARCHAR2 (4) := CHR (13) || CHR (10);
 v_set_layout_option BOOLEAN;
 dir_name varchar2(100);
 /* CURSOR req_status
 IS
 SELECT SUBSTR (outfile_name, 55, 23) filename,
 SUBSTR (outfile_name, 1, 64) outfilepath
 FROM applsys.fnd_concurrent_requests
 WHERE request_id = l_request_id
 AND phase_code = 'C'
 AND status_code = 'C';*/
 directory_path VARCHAR2 (2000);
 lv_subject VARCHAR2 (100);
 lv_msg VARCHAR2 (700);
 lv_msghdr VARCHAR2 (100);
 lv_pdf_filename VARCHAR2 (200);
 BEGIN
 apps.fnd_global.apps_initialize
 (user_id => apps.fnd_global.user_id,
 resp_id =>apps.fnd_global.resp_id,
 resp_appl_id => apps.fnd_global.resp_appl_id
 l_request_id :=
 apps.fnd_request.submit_request
 ( 'BOM',
 'CSTCRACCRCV',
 NULL,
 NULL,
 FALSE,
 Source_Application,
 Application ,
 Dummy_Parameter_0,
 Ledger ,
 Process_Category,
 End_Date ,
 Create_Accounting_Flag,
 Dummy_Parameter_1 ,
 Accounting_Mode ,
 Dummy_Parameter_2,
 Errors_Only_Flag,
 Report ,
 Transfer_to_GL_Flag,
 Dummy_Parameter_3,
 Post_to_GL_Flag ,
 GL_Batch_Name ,
 Mixed_Currency_Precision,
 Include_Zero_Amt_Lines_Flag,
 Request_ID ,
 Entity_ID,
 Source_Application_Name,
 Application_Name,
 Ledger_Name ,
 Process_Category_Name,
 Create_Accounting ,
 Accounting_Mode_Name,
 Errors_Only ,
 Report_Level,
 Transfer_to_GL,
 Post_in_GL ,
 Include_Zero_Amount_Lines,
 Valuation_Method ,
 Security_ID_Integer_1,
 Security_ID_Integer_2,
 Security_ID_Integer_3,
 Security_ID_Char_1 ,
 Security_ID_Char_2 ,
 Security_ID_Char_3 ,
 Concurrent_Request_ID,
 P_INCLUDE_USER_TRX_ID_FLAG,
 P_INCLUDE_USER_TRX_IDENTIFIERS,
 P_DEBUG_FLAG
 COMMIT;
 IF (l_request_id <= 0)
 THEN
 errmsg := apps.fnd_message.get ();
 ELSE
 wait_stat :=
 apps.fnd_concurrent.wait_for_request (l_request_id,
 10,
 360,
 phase,
 status,
 dphase,
 dstatus,
 MESSAGE
 IF dphase = 'COMPLETE'
 THEN
 dir_name :='XX_CREATE_ACCT_LOG';
 l_file_name := 'l' || l_request_id || '.REQ';
 lv_subject := NULL;
 lv_msg := NULL;
 lv_msghdr := NULL;
 lv_pdf_filename := NULL;
 lv_subject := 'testing mail :Request for Create Accounting not completed';
 lv_msg :=
 'Please find attachement here with the Status Of Create Accounting Reciving from cost management'
 || crlf;
 lv_msghdr := 'Dear Sir' ;
 lv_pdf_filename := l_file_name;
 send_mail (l_senderemail,
 '[email protected]',
 lv_subject,
 lv_msghdr,
 lv_msg,
 lv_pdf_filename,
 'text/application',
 dir_name
 END IF;
 END IF;
 END submit_request;
 PROCEDURE send_mail (
 p_sender IN VARCHAR2,
 p_recipient IN VARCHAR2,
 p_subject IN VARCHAR2,
 p_mailbodyhdr IN VARCHAR2,
 p_mailbody IN VARCHAR2,
 p_filename IN VARCHAR2,
 p_filetype IN VARCHAR2,
 dir_name in VARCHAR2
 AS
 v_msg VARCHAR2 (32000);
 src_file BFILE;
 i INTEGER := 1;
 v_raw RAW (500);
 v_length INTEGER := 0;
 v_buffer_size INTEGER := 57;
 v_mailconn UTL_SMTP.connection;
 gc_crlf VARCHAR2 (4) := CHR (13)
 || CHR (10);
 gc_lf VARCHAR2 (4) := CHR (10);
 crlf VARCHAR2 (2) := CHR (13)
 || CHR (10);
 gc_mailhost VARCHAR2 (255) := '172.16.11.2';
 -- gc_maildomain VARCHAR2 (255) := 'pune.com';
 msg VARCHAR2 (32767);
 boundary CONSTANT VARCHAR2 (256)
 := '-----7D81B75CCC90D2974F7A1CBD';
 first_boundary CONSTANT VARCHAR2 (256)
 := '--' || boundary || UTL_TCP.crlf;
 last_boundary CONSTANT VARCHAR2 (256)
 := '--' || boundary || '--' || UTL_TCP.crlf;
-- A MIME type that denotes multi-part email (MIME) messages.
 multipart_mime_type CONSTANT VARCHAR2 (256)
 := 'multipart/mixed; boundary="' || boundary || '"';
 BEGIN
 DBMS_OUTPUT.ENABLE (100000);
 --fnd_file.put_line (fnd_file.output, '------------------------------------------------------' );
 v_mailconn := UTL_SMTP.open_connection (gc_mailhost, 26);
 UTL_SMTP.helo (v_mailconn, gc_mailhost);
 UTL_SMTP.mail (v_mailconn, p_sender);
 UTL_SMTP.rcpt (v_mailconn, p_recipient);
 UTL_SMTP.open_data (v_mailconn);
 msg :=
 'Date: '
 || TO_CHAR (SYSDATE, 'Dy, DD Mon YYYY hh24:mi:ss')
 || crlf
 || 'From:[email protected] '
 -- || p_sender
 || crlf
 || 'Subject: '
 || p_subject
 || crlf
 || 'To: [email protected]'
 -- || p_recipient
 || crlf
 || 'MIME-Version: 3.1'
 || crlf
 || -- Use MIME mail standard
 'Content-Type: multipart/mixed;'
 || crlf
 || ' boundary="-----SECBOUND"'
 || crlf
 || crlf
 || '-------SECBOUND'
 || crlf
 || 'Content-Type: text/plain;'
 || crlf
 || 'Content-Transfer_Encoding: 7bit'
 || crlf
 || crlf
 || p_mailbodyhdr
 || crlf
 || crlf
 || p_mailbody
 || crlf
 || crlf
 || crlf
 || crlf
 || -- Message body
 'Regards'
 || crlf
 || 'HR and Payroll Team'
 || crlf
 || crlf
 || ' Note- Please ignore the leave status and number of days.'
 || crlf
 || crlf
 || '-------SECBOUND'
 || crlf
 || 'Content-Type'
 || ': '
 || p_filetype
 || crlf
 || 'Content-Disposition: attachment; filename="'
 -- || 'Create Accounting'
 -- || '.REQ'
 ||p_filename -- p_filename
 || '"'
 || crlf
 || 'Content-Transfer-Encoding: base64'
 || crlf
 || crlf;
 UTL_SMTP.write_data (v_mailconn, msg);
 src_file := BFILENAME (dir_name, p_filename);
 DBMS_LOB.fileopen (src_file, DBMS_LOB.file_readonly);
 v_length := DBMS_LOB.getlength (src_file);
 WHILE i < v_length
 LOOP
 DBMS_LOB.READ (src_file, v_buffer_size, i, v_raw);
 UTL_SMTP.write_raw_data (v_mailconn,
 UTL_ENCODE.base64_encode (v_raw)
 UTL_SMTP.write_data (v_mailconn, UTL_TCP.crlf);
 i := i + v_buffer_size;
 END LOOP while_loop;
 UTL_SMTP.write_data (v_mailconn, last_boundary);
 UTL_SMTP.write_data (v_mailconn, UTL_TCP.crlf);
 DBMS_LOB.fileclose (src_file);
 UTL_SMTP.close_data (v_mailconn);
 UTL_SMTP.quit (v_mailconn);
 EXCEPTION
 WHEN OTHERS
 THEN
 UTL_SMTP.quit (v_mailconn);
 DBMS_OUTPUT.put_line (SQLCODE || SQLERRM);
 -- FND_FILE.PUT_LINE (FND_FILE.LOG,'error while fetching values from CO_CODE'|| SQLERRM );
 END send_mail;
END xx_create_acct;Edited by: BluShadow on 18-Apr-2011 09:49
added {noformat}{noformat} tags. Please see the [url=SQL and PL/SQL FAQ and PL/SQL FAQ[/url] for info on how to post on the forums

I didn't get the information, What I want. Anyway, in the BLOB writing portion you have to create a temporary LOB and load your file into that temporary LOB and the write it into chunks.
Something like
DBMS_LOB.OPEN(v_src_loc, DBMS_LOB.LOB_READONLY); --Read the file
DBMS_LOB.CREATETEMPORARY(l_blob, TRUE); --Create temporary LOB to store the file.
v_amount := DBMS_LOB.GETLENGTH(v_src_loc); --Amount to store.
DBMS_LOB.LOADFROMFILE(l_blob, v_src_loc, v_amount); -- Loading from file into temporary LOB
/* Writing the BLOL in chunks */
WHILE l_pos < l_blob_len LOOP
 DBMS_LOB.READ(l_blob, l_amount, l_pos, l_buffer);
 UTL_SMTP.write_raw_data(v_connection_handle,
 UTL_ENCODE.BASE64_ENCODE(l_buffer));
 UTL_SMTP.WRITE_DATA(v_connection_handle, UTL_TCP.CRLF);
 l_buffer := NULL;
 l_pos := l_pos + l_amount;
END LOOP;For more example see these posts:
Re: Sending UTL_SMTP mail with single jpg attachment issue
Re: getting junk letters instead of photo in an email.

Document control failed due to error in [DOCMGR-CANCEL] with a return code

i am getting this error while calceling the purchase order "Document control failed due to error in [DOCMGR-CANCEL] with a return code of [OTHER]. "
I am doing the calcel like this
Nav: buyer work centre --> order
searche the po and then
select order --> cancel then click GO button
i gave the Reason as Cancel
communication method: email
Cancel Requisition: Yes
Please help on this, its urgent.
Thanks,
Vijay.

Hi Vijay,
Check this MOS note.
Cancelling A Standard Purchase Order In Buyer Work Center Results In Error [Docmgr-Cancel] With A Return Code [ID 1338826.1]
Thanks
-Arif.

Fdpstp failed due to ora-12899 value too large for column

Hi All,
User facing this problem while running the concurrent program.
the program is complted but with rhis error.
fdpstp failed due to ora-12899 value too large for column
Can any one tell me the excat solution for this?
RDBMS : 10.2.0.3.0
Oracle Applications : 11.5.10.2

User facing this problem while running the concurrent program.
the program is complted but with rhis error.Is this a seeded or custom concurrent program?
fdpstp failed due to ora-12899 value too large for column
Can any one tell me the excat solution for this?Was this working before? If yes, any changes been done recently?
Can other users run the same concurrent program with no issues?
Please post the contents of the concurrent request log file here.
Please ask your developer to open the file using Reports Builder and compile the report and run it (if possible) with the same parameters.
OERR: ORA-12899 value too large for column %s (actual: %s, maximum: %s) [ID 287754.1]
Thanks,
Hussein

Activation failed due to sructure generation error.-URGENT

i tried to check in an activity but activation failed due to the foloowing error:PLEASE HELP VERY URGENT
Development Component Build (2008-03-14 10:09:20)
Component name: tablist
Component vendor: worldbank.org
SC compartment: worldbank.org_GDB_OPERATIONS_1
Configuration: WAS_MIGATEST_D
Location: WAS_MIGATEST_D
Source code location: http://sapjdi01:50000/dtr/ws/MIGATEST/worldbank.org_GDB_OPERATIONS/dev/active/DCs/worldbank.org/tablist/_comp/
DC root folder: /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/worldbank.org/tablist/_comp/
DC type: Web Dynpro
Host: sapjdi01
DC Model check:
          [dcmake] All used DCs are available locally
          [dcmake] validating dependency to build plugin "sap.com/tc/bi/bp/webDynpro"
          [dcmake] validating dependency to public part "default" of DC "sap.com/tc/cmi"
          [dcmake] validating dependency to public part "default" of DC "sap.com/tc/ddic/ddicruntime"
          [dcmake] validating dependency to public part "default" of DC "sap.com/tc/ddic/metamodel/content"
          [dcmake] validating dependency to public part "default" of DC "sap.com/tc/wd/webdynpro"
          [dcmake] validating dependency to public part "default" of DC "sap.com/tc/logging"
          [dcmake] validating dependency to public part "default" of DC "sap.com/tc/wdp/metamodel/content"
          [dcmake] validating dependency to public part "default" of DC "sap.com/com.sap.aii.proxy.framework"
          [dcmake] validating dependency to public part "default" of DC "sap.com/com.sap.aii.util.misc"
          [dcmake] validating dependency to public part "default" of DC "sap.com/com.sap.exception"
          [dcmake] validating dependency to public part "default" of DC "sap.com/com.sap.mw.jco"
          [dcmake] validating dependency to public part "pp_connserv" of DC "worldbank.org/connserv"
          [dcmake] DC model check OK
Start build plugin:
          [dcmake] using build plugin: sap.com/tc/bi/bp/webDynpro
          [dcmake] starting build plugin from : /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/bi/bp/webDynpro/_comp/gen/default/public/webDynpro/
Build Plugin 'WebDynproPlugin', Version 6.40 SP 19 (630_VAL_REL, built on 2006-10-27 02:01:51 CEST)
   development component: tablist (worldbank.org)
      software component: GDB_OPERATIONS (worldbank.org)
                location: WAS_MIGATEST_D
                    type: Web Dynpro
           build variant: default
         source location: http://sapjdi01:50000/dtr/ws/MIGATEST/worldbank.org_GDB_OPERATIONS/dev/active/
       plugin start time: 2008-03-14 10:09:21 GMT+00:00
                 Java VM: Classic VM, 1.4.2 (IBM Corporation)
General options:
convert *.xlf to *.properties: yes
include sources for debugging: yes
Source folder META-INF exists but is empty.
Source folder src/configuration exists but is empty.
Plugin initialized in 1.026 seconds
Warning: Runtime dependency to connserv (worldbank.org) not allowed (incompatible runtime type).
Preparing data context..
No 'default' JDK defined, will use running VM.
Data context prepared in 0.128 seconds
Executing macro file..
Using macro file:     /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/bi/bp/webDynpro/_comp/gen/default/public/webDynpro/macros/build.vm
Creating output file: /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/worldbank.org/tablist/_comp/gen/default/logs/build.xml
Macro file executed in 3 seconds
Starting Ant..
Using build file:     /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/worldbank.org/tablist/_comp/gen/default/logs/build.xml
Using build target:   build
Generation folder:    /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/t/013EC0ABDECC3015F13C417F5CBF217B
Using Ant version:    1.5.4
prepare:
     [mkdir] Created dir: /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/worldbank.org/tablist/_comp/gen/default/deploy
compile:
     [ddgen]
     [ddgen] [Info]    Property deployment is true: Deployment information is provided!
     [ddgen] [Info]    Property sourcepath: /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/worldbank.org/tablist/_comp/src/packages
     [ddgen] [Info]    Property targetpath: /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/t/013EC0ABDECC3015F13C417F5CBF217B/gdd
     [ddgen] [Info]    Property archivename: worldbank.org~tablist
     [ddgen] [Info]    Property vendor: worldbank.org
     [ddgen] [Info]    Property dcname: tablist
     [ddgen] [Info]    Property language: Available languages are automatically determined!
     [ddgen] [Info]    Property addpaths ...
     [ddgen] [Info]       SapMetamodelWebdynproContent.zip - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/bi/extmm/_comp/gen/default/public/def/lib/model
     [ddgen] [Info]       SapMetamodelDictionaryContent.zip - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/bi/extmm/_comp/gen/default/public/def/lib/model
     [ddgen] [Info]       worldbank.orgconnservpp_connserv.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/worldbank.org/connserv/_comp/gen/default/public/pp_connserv/lib/java
     [ddgen] [Info]       exception.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/com.sap.exception/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       SapDictionaryTypeServices.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/ddic/ddicruntime/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       SapDictionaryTypesRuntime.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/ddic/ddicruntime/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       jrfc.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/com.sap.mw.jco/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       SapMetamodelWebdynproContent.zip - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/wdp/metamodel/content/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       aii_proxy_rt.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/com.sap.aii.proxy.framework/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       cmiapi.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/cmi/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       webdynproadmin.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/wd/webdynpro/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       webdynprobasesrvc.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/wd/webdynpro/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       webdynproclientserver.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/wd/webdynpro/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       webdynpromodelimpl.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/wd/webdynpro/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       webdynpromodel_dynamicrfc.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/wd/webdynpro/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       webdynpropdfobject.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/wd/webdynpro/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       webdynproprogmodel.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/wd/webdynpro/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       webdynproruntime_designtime_coupling.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/wd/webdynpro/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       webdynproruntime_designtime_coupling_api.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/wd/webdynpro/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       webdynproruntime_repository.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/wd/webdynpro/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       webdynproruntime_repository_pmr.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/wd/webdynpro/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       webdynproservices.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/wd/webdynpro/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       SapMetamodelDictionaryContent.zip - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/ddic/metamodel/content/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       aii_util_misc.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/com.sap.aii.util.misc/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       logging.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/logging/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]       logging.perf.jar - /usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/logging/_comp/gen/default/public/default/lib/java
     [ddgen] [Info]    Initialize generation templates from configuration jar:file:/usr/sap/WAS/DVEBMGS00/j2ee/cluster/server0/temp/CBS/199/.B/48895/DCs/sap.com/tc/bi/extddic/_comp/gen/default/public/def/lib/java/SapDictionaryGenerationCore.jar!/DictionaryGenerationConfigurationCompiled.xml
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Origin.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/PackagePointer.java
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Inves_Id.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Ccy_Code.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Subm_Type.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Uw_Upi.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Guar_Holder.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Conver_Type.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Doc_Num.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Sic_Cde.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Rcvr_Type.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Notif_Sndr.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Notif_Rcvr.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Modified_By.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/Symsgid.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Status_Type.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/Bapi_Msg.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Inves_Ty.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Reason_Dt.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Stl_Upi.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/Balmnr.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Notif_Id.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/Bapi_Line.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Frcast_Chk.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Migeo_Upi.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Waiv_Flag.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Item_Num.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/Symsgno.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Status_Categ.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Mngmt_Gr.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Reg_Num.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Stat_Chng_Dt.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Migaorg_Code.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Rcvr_Grp.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Commnt_Eventtype.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/Bapi_Param.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Doc_Typ.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Stl_Comment.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Src_Upi.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Notif_Eventtype.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/Bapi_Mtype.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Sndr_Type.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/Bapi_Fld.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Commnt_Doctype.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Cmmt_User.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/Symsgv.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Sme_Share.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Description.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/Balognr.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/Bapilogsys.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Amount.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Status.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Reason_Type.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Comment_Id.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Time_Stamp.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Reason.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__Miga_Source.gsimpletype
     [ddgen] [Info]    Generating datatypes/org/wb/operations/stl/types/__Miga__S_Doc_Typ.gstructure
     [ddgen] [Error]   Structure org.wb.operations.stl.types.__Miga__Appl is not generated
     [ddgen] [Error]   BuiltIn Type or Simple Type expected
     [ddgen] [Info]    Catching throwable null
     [ddgen] [Info]    com.sap.dictionary.generation.ant.GenerationAntTaskError
     [ddgen]      at com.sap.dictionary.generation.ant.GenerationAnt.showCheckResult(GenerationAnt.java:171)
     [ddgen]      at com.sap.dictionary.tools.generation.Generation.generatePersistentStructure(Generation.java:480)
     [ddgen]      at com.sap.dictionary.tools.generation.console.GenerationConsole.generate(GenerationConsole.java:168)
     [ddgen]      at com.sap.dictionary.generation.ant.GenerationAnt.main(GenerationAnt.java:47)
     [ddgen]      at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
     [ddgen]      at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:85)
     [ddgen]      at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:58)
     [ddgen]      at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:60)
     [ddgen]      at java.lang.reflect.Method.invoke(Method.java:391)
     [ddgen]      at com.sap.dictionary.generation.ant.DDGenAntTask.execute(DDGenAntTask.java:219)
     [ddgen]      at org.apache.tools.ant.Task.perform(Task.java:341)
     [ddgen]      at org.apache.tools.ant.Target.execute(Target.java:309)
     [ddgen]      at org.apache.tools.ant.Target.performTasks(Target.java:336)
     [ddgen]      at org.apache.tools.ant.Project.executeTarget(Project.java:1339)
     [ddgen]      at com.sap.tc.buildplugin.techdev.ant.util.AntRunner.run(AntRunner.java:115)
     [ddgen]      at com.sap.tc.buildplugin.AbstractAntBuildAction.execute(AbstractAntBuildAction.java:65)
     [ddgen]      at com.sap.tc.buildplugin.AbstractPlugin.handleBuildStepSequence(AbstractPlugin.java:226)
     [ddgen]      at com.sap.tc.buildplugin.AbstractPlugin.performBuild(AbstractPlugin.java:202)
     [ddgen]      at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
     [ddgen]      at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:85)
     [ddgen]      at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:58)
     [ddgen]      at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:60)
     [ddgen]      at java.lang.reflect.Method.invoke(Method.java:391)
     [ddgen]      at com.sap.tc.buildtool.PluginCommunicator.maybeInvoke(PluginCommunicator.java:114)
     [ddgen]      at com.sap.tc.buildtool.PluginCommunicatorV2.communicate(PluginCommunicatorV2.java:42)
     [ddgen]      at com.sap.tc.buildtool.PluginHandlerImpl.handlePluginCommunication(PluginHandlerImpl.java:354)
     [ddgen]      at com.sap.tc.buildtool.PluginHandlerImpl.execute(PluginHandlerImpl.java:176)
     [ddgen]      at com.sap.tc.devconf.impl.DCProxy.make(DCProxy.java:1726)
     [ddgen]      at com.sap.tc.devconf.impl.DCProxy.make(DCProxy.java:1498)
     [ddgen]      at com.sap.tc.buildcontroller.CBSBuildController.build(CBSBuildController.java:727)
     [ddgen]      at com.sap.tc.buildcontroller.CBSBuildController.execCommand(CBSBuildController.java:503)
     [ddgen]      at com.sap.tc.buildcontroller.CBSBuildController.evalCmdLine(CBSBuildController.java:442)
     [ddgen]      at com.sap.tc.buildcontroller.CBSBuildController.run(CBSBuildController.java:314)
     [ddgen]      at com.sap.tc.buildcontroller.CBSBuildController.exec(CBSBuildController.java:252)
     [ddgen]      at com.sap.tc.buildcontroller.CBSBuildController.mainLoop(CBSBuildController.java:207)
     [ddgen]      at com.sap.tc.buildcontroller.CBSBuildController.main(CBSBuildController.java:168)
     [ddgen] ERROR: Unknown exception during generation null (com.sap.dictionary.generation.ant.GenerationAntTaskError)
     [ddgen] ERROR: Generation failed due to errors (3 seconds)
Ant runtime 5.593 seconds
Ant build finished with ERRORS
[Error]   Generation failed!
Error: Build stopped due to an error: [Error]   Generation failed!
Build plugin finished at 2008-03-14 10:09:32 GMT+00:00
Total build plugin runtime: 10.143 seconds
Build finished with ERROR

I think the "," that comes in the flat file. CHange the number fields in the file from ",". If it has 1000 separator remove them. You need not have them in the file. In your case i think the decimals are coming as ",". In that case change your user settings for decimal places and then try to load.
Hope this helps

Trying to reinstall CS5.5 Master Collection from DVD media on Windows 7 64 bit - setup.exe fails due to msxml3.dll error PDApp message [FATAL] PIM - Failed to Create XML instance : DOMDocument40 ADXML::initWithXMLPath Error:80040154

If anyone is able to solve this they are a genius (or I am doing something very stupid!)
I am trying to reinstall CS5.5 Master Collection from DVD media on Windows 7 64 bit PC but setup.exe fails due to a msxml3.dll error.
Following a big bundle of recent Windows 7 updates, I started getting 'bad image' msxml3.dll error messages when opening any CS5.5 master collection program (Eg Premiere / Photoshop / Illustrator / Dreamweaver). Following advice on some threads here I tried uninstalling and then using the Adobe CC Cleaner Tool to clean up install, then reinstalling from my original DVD media.
Whenever I try using run setup.exe from installtion disc 1 the installing fails due to 'Missing files'. I have also tried dowloading trial versions and runing setup.exe fro mthe downloaded files but i still get the same message.
I have searched the forum and others have experienced this error but none of the solutions I have found seem to be working for me - as many seem to relate to download installations whereas I am installing from original DVD media (which worked fine before on the same PC)
These are the FATAL messages from the PDApp log
12/11/2014 15:29:27 [FATAL] PIM - Failed to Create XML instance : DOMDocument40 ADXML::initWithXMLPath Error:80040154
12/11/2014 15:29:27 [FATAL] Setup - Could not initialize ADXML object
12/11/2014 15:29:27 [FATAL] Setup - Unable to initialize. Error parsing setup.xml file
The PDApp troubleshooting seems to indicate that this is caused by error in downloads but I am getting it with both original media DVD and downloads.
I have also tried using my logon (which has admin privileges) and under our main admin account - and I get the same errors.
Is a clean install of Windows 7 + CS5.5 my only option?
Any help / info / advice / solutions very much appreciated! I have spent the last 2 days trying to sort this out and seem to be getting nowhere.
Thanks.

Thanks for the reply kglad - much appreciated.
I have already tried that option (along with downloading files) as it was one of the solutions mentioned on other threads, but that also failed.
Any other ideas?

Reading Exchange Online tenant version failed due to an exception when trying to install Exchange 2013 in a hybrid environment.

We currently have an Exchange 2010 hybrid install and we have migrated all of our email accounts to Office 365. Now, I want to do an on-premise install of Exchange 2013 to better manage the hybrid setup. When I try to install Exchange 2013 it
asks for my O365 credentials to do a hybrid check but always fails with the above message. I've done quite a bit of searching but haven't come up with anything useful.
Here is what appears in the exchange setup log:
[09/22/2014 15:48:27.0024] [0] Reading the Exchange Online tenant version information failed due to an exception. Please check the Exchange setup log for more information.
[09/22/2014 15:48:27.0024] [0] Could not load type 'Microsoft.Exchange.Data.Directory.DirectoryBackendType' from assembly 'Microsoft.Exchange.Data.Directory, Version=15.0.0.0, Culture=neutral,
[09/22/2014 15:48:27.0024] [0] Could not load type 'Microsoft.Exchange.Data.Directory.DirectoryBackendType' from assembly 'Microsoft.Exchange.Data.Directory, Version=15.0.0.0, Culture=neutral,
[09/22/2014 15:48:27.0147] [0] Session=Tenant Total Cmdlet Time=1.6931035s
[09/22/2014 15:48:27.0148] [0] Microsoft.Exchange.Management.Deployment.HybridConfigurationDetection.HybridConfigurationDetectionException: Reading the Exchange Online tenant version information failed due to an exception. Please check the Exchange setup log
for more information. ---> System.TypeLoadException: Could not load type 'Microsoft.Exchange.Data.Directory.DirectoryBackendType' from assembly 'Microsoft.Exchange.Data.Directory, Version=15.0.0.0, Culture=neutral,

Hi,
I recommend you post this in
office 365 forum also, as they should have more professional knowledge on hybrid deployments
and you may get effective solution timely.
In addition, I found a similar thread for you reference:
http://community.office365.com/en-us/f/156/t/255739.aspx
According to the reply of this thread, if you run the HCW (Hybrid Configuration Wizard) to deploy the Exchange Hybrid environment, there will generate an HCW log
file for this deployment.
Additional troubleshooting information is available in the Update-HybridConfiguration log file located at C:\Program Files\Microsoft\Exchange Server\V1*\Logging\Update-HybridConfiguration\HybridConfiguration****.log
Best regards,
Niko Cheng
TechNet Community Support

Ecatt script fails due "Error in OLE API method Call" error

Hi ,
Ecatt scripts fails due to "Error in OLE API method Call" error, this error message occurs once a while.
We are calling testpartner scripts from Ecatt using REFEXT command. At times this ECATT script fails due to above issue.
Please help in solving this issue.
Thanks,
Asha

>
Asha Nagaraj wrote:
> Hi ,
>
> Ecatt scripts fails due to "Error in OLE API method Call" error, this error message occurs once a while.
>
> We are calling testpartner scripts from Ecatt using REFEXT command. At times this ECATT script fails due to above issue.
>
> Please help in solving this issue.
>
> Thanks,
> Asha
Hi Asha,
Are those components are connected and the necessay settings has been done?
Regards,
SSN.

Apple's Audio Units Fail Validation in Yosemite

Why do Apple's audio units fail validation in Yosemite
Anyone else having this problem ?
What's the fix ?
Even Logic Pro X 10.0.7 can't validate Apple's AU plugs.
[Rant: i have never been so disappointed with a Mac OS as i am with YO. Most of my midi/audio/video programs will not work because of the validation of AU/VST plugs. I am this close to trashing Yosemite . It reminds me of my OS 9 days: if you even looked in the wrong direction the system stop working.]

are there any AU plugs here, in the components folder...?

Primary ASA unit fails due to IPS

Similar Messages

Maybe you are looking for