Prime 2.1 and 4500X-VSS support?

Anyone with a Prime 2.1.2 that successfully archives configurations from a WS-C4500X-16 running VSS?
Error message after Configuration Archive:
No device package found for the specified device.
The software on the 4500X is 03.04.03SG.
Support for 4500X in PI 2.1.2:
Device Type
SYSOIDS
S/W Version
Software
Cisco Catalyst 4500X-16 SFP+ Switch
OID:1.3.6.1.4.1.9.1.1605
IOS
Cisco Catalyst 4500X-32 SFP+ Switch
OID:1.3.6.1.4.1.9.1.1606
IOS
Tanks

Yes, all device packages are installed (including 7.0) and the Pi 2.1.2 patch.
Info from "ifm_config_archive.log" when trying Archive the Configuration:
[2014-12-09 19:58:11,300] [pool-37-thread-5] [service] [ERROR] - Thread Id : [9,460] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching VLAN file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]'
Maybe the Prime don't know where to find the vlan.dat on the 4500X-VSS ?
#dir cat4000_flash:
Directory of cat4000_flash:/
1 -rw- 2236 <no date> vlan.dat
sysObjectID (1.3.6.1.2.1.1.2) is
.iso.org.dod.internet.private.enterprises.cisco.ciscoProducts.cat4xxxVirtualSwitch
That is not the expected and supported value "4500X-16" above
Update: Error on fetching running and startup config as well:
[2014-12-09 20:24:21,818] [pool-37-thread-9] [service] [ERROR] - Thread Id : [10,013] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching RUNNINGCONFIG file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]
[2014-12-09 20:25:31,882] [pool-37-thread-9] [service] [ERROR] - Thread Id : [10,013] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching STARTUPCONFIG file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]

Similar Messages

Is VSS supported in Cisco Prime Infrastructure 1.2?

Is VSS supported in Cisco Prime Infrastructure 1.2?

VSS support (converting standalone switches into a VSS) was introduced with LMS 3.0.1 if I remember well and it is still there in LMS 4.2 (Cisco Prime Infrastructure):
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.1/user/guide/configuration/configvss.html
Config Mgmt is supported, also.

4500x VSS and SFP-H10GB-CU1M

Hello
I have (2) Cisco 4500x with a VSS config. I als have a couple cables "SFP-H10GB-CU1M".
I want to make sure I have this physically setup correctly. I have searched but not found anything specific enough.
Please review and advise.

Yes, all device packages are installed (including 7.0) and the Pi 2.1.2 patch.
Info from "ifm_config_archive.log" when trying Archive the Configuration:
[2014-12-09 19:58:11,300] [pool-37-thread-5] [service] [ERROR] - Thread Id : [9,460] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching VLAN file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]'
Maybe the Prime don't know where to find the vlan.dat on the 4500X-VSS ?
#dir cat4000_flash:
Directory of cat4000_flash:/
1 -rw- 2236 <no date> vlan.dat
sysObjectID (1.3.6.1.2.1.1.2) is
.iso.org.dod.internet.private.enterprises.cisco.ciscoProducts.cat4xxxVirtualSwitch
That is not the expected and supported value "4500X-16" above
Update: Error on fetching running and startup config as well:
[2014-12-09 20:24:21,818] [pool-37-thread-9] [service] [ERROR] - Thread Id : [10,013] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching RUNNINGCONFIG file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]
[2014-12-09 20:25:31,882] [pool-37-thread-9] [service] [ERROR] - Thread Id : [10,013] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching STARTUPCONFIG file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]

VSS support on cat 4500x

Hi,
when the VSS will be supported on Catalyst Supervisor Engine 7-E or 7-LE and on Catalyst 4500-X?
And does VSS will require Enterprise license ? or the IP base will be enaugh?
Tks
Paolo

Hi,
Is there any info on the VSS license for SUP7L-E ?
http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/release/note/OL_27990-01.html
Under Table 5 - Support by Image Type; VSS is listed as available on IP Base (SUP7E only) and a plain Yes under Enterprise Services
http://www.cisco.com/en/US/prod/collateral/switches/ps10902/ps12332/at_a_glance_c45-696645.pdf
Under Table 1 - Minimum License for VSS; IP Base or higher (7-E) or special license (7-LE and Catalyst 4500-X)
There appears to be no option on the CCO configuration tools to add VSS license on 4500R+E chasiss bundles with for example dual SUP7L-E and IP Base
How are you meant to purchase/license VSS on 4500E Chassis + SUP7L-E ?
thanks,
Sez

WS-X6848-SFP module are supported with LMS Prime 4.1 and 4.2

Hi,
I would like to know if WS-X6848-SFP modules are supported with LMS Prime 4.1 and 4.2.
Thanks for your help,
SILVIA

It looks like they just added the WS-X6848-TX variant with the latest C6000IOS CiscoView package update (Version 37, dated 31 July 2012 - readme)
I'd expect the -SFP variant should be in the next update.
You should open a TAC case to make sure that it's brought to the attention of the dev team if they aren't already working on it. One of the tenets of Cisco Prime LMS is "Day 1 support" of new devices.

JDeveloper 11 and VSS Support?

The VSS Extension (available at sourceforge.net) does not work with JDev 11 (Just JDev 10). Are there plans for VSS Support in JDev 11, or am I better off convincing my management that JDeveloper projects should use either Subversion or CVS?
Edited by: klee on Oct 22, 2008 10:26 AM

This extension is open source - so you can take on the task of upgrading it to support JDeveloper 11g :-)
As for us at Oracle we don't have plans to do development around supporting VSS - we do have support for MS Team Studio though.
I would recommend that you push your managers towards using Subversion - the fact that it is a free tool and a very popular tool in the Java community should be enough of an argument - and the fact that the support in JDeveloper is built-in can be the cherry on the cake.

Prime 2.1 and Nexus netflow

I have installed Prime 2.1 for evaluation while waiting on licenses. I have Netflow working from my 2921 and 3945 routers but cannot get the Nexus 7010's to work. Nexus defaults to version 9, but I do not see any templates in 2.1 for version 9. I set the Nexus exporter to be version 5 but still see nothing. Also, the Nexus is communicating on the mgmt port to the Prime 2.1 infrastructure. Does anyone have this working?

Yes, all device packages are installed (including 7.0) and the Pi 2.1.2 patch.
Info from "ifm_config_archive.log" when trying Archive the Configuration:
[2014-12-09 19:58:11,300] [pool-37-thread-5] [service] [ERROR] - Thread Id : [9,460] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching VLAN file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]'
Maybe the Prime don't know where to find the vlan.dat on the 4500X-VSS ?
#dir cat4000_flash:
Directory of cat4000_flash:/
1 -rw- 2236 <no date> vlan.dat
sysObjectID (1.3.6.1.2.1.1.2) is
.iso.org.dod.internet.private.enterprises.cisco.ciscoProducts.cat4xxxVirtualSwitch
That is not the expected and supported value "4500X-16" above
Update: Error on fetching running and startup config as well:
[2014-12-09 20:24:21,818] [pool-37-thread-9] [service] [ERROR] - Thread Id : [10,013] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching RUNNINGCONFIG file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]
[2014-12-09 20:25:31,882] [pool-37-thread-9] [service] [ERROR] - Thread Id : [10,013] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching STARTUPCONFIG file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]

4500X VSS - Dual Active Detection with ePAgP

Hello,
I am interesting if 3560x supports ePAgP. I have VSS which is formed by two 4500x switches. Can I use 3560x, which is connected two both VSS members via 10Gb optics for Dual Active detection ?

Hi,
As PagP is not supported accross differents 3750(-X) units of a stack (but LACP yes), ePagp is not supported also. The MEC has to be formed from the same 3750(-X) unit / Standalone 35xx and 37xx do support PAgPand thus ePAgP.
Page 17 and 20 of http://www.cisco.com/web/DK/assets/docs/presentations/VSS_0109.pdf =>
"Since cross-stack EtherChannel does not support PAgP, it can not use enhanced PAgP for dual ACTIVE detection.
Hence the only alternative for cross-stack EtherChannel configuration is to use BFD as a dual ACTIVE detection method"
Hope it helps.
Regards;
Inayath

Ask the Expert: Overview of Cisco Prime Service Catalog and Process Orchestrator Solutions

Welcome to this Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about the Cisco Prime Service Catalog and Process Orchestrator solutions.
Cisco expert Jason Davis will discuss Cisco’s network management products offered under the Cisco Prime framework. If you have questions about Cisco Prime infrastructure or data center automation with our Cisco Prime Service Catalog and Process Orchestrator solutions, join us on the Cisco Support Community.
Jason Davis is a distinguished services engineer in the Intelligent Infrastructure Practice team of Cisco Advanced Services. His role is to provide strategic and tactical consulting for hundreds of Advanced Services customers, lead service innovation, and assess new services and technologies. Jason's primary expertise areas are in network management systems, intelligent automation, virtualization, data center operations, software-defined networking, and network programmability.
Based out of the Research Triangle Park (RTP) campus, Jason is also responsible for administering the Research Triangle Park Network Management Lab, Cisco's largest network management lab.
Since joining Cisco in 1998, Jason has been a frequent speaker at Cisco's Networkers and CiscoLive conferences in the United States and Europe. In the past five years he has also been involved in the conference network setup and monitoring. He is a much sought-after resource by the field sales teams to assist with presales solutions and executive briefings. He has provided strategic and tactical network management consulting for several hundred customers.
Jason is a subject matter expert with the following products and features:
Cisco Prime LAN management solution
Cisco Prime infrastructure
CiscoSecure ACS
Cisco Prime Network Registrar
Cisco Process Orchestrator
Cisco Prime Service Catalog
Cisco IP SLA
Embedded Event Manager
SNMPv3
onePK and OpenFlow
Cisco UCS
Device instrumentation
VMware ESX, ESXi, and vCenter
ITIL
Jason received his bachelor of science degree in electrical engineering from the University of Miami (FL). He has been married for 20 years and has 4 children. His interests include providing audiovisual technical support for churches and conference venues, camping and biking with his family, remote-control helicopter piloting, paintball, and recreational shooting.
Remember to use the rating system to let Jason know if you have received an adequate response.
Because of the volume expected during this event, Jason might not be able to answer every question. Remember that you can continue the conversation in Data Center > Intelligent Automation under the subcommunity Cisco Prime Service Catalog shortly after the event. This event lasts through September 12, 2014. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.

Hello Jason,
Thank you very much for welcoming me to your expert discussion :) I feel to be in the right place, at the right time. Thank you also for answering question beyond your scope here, much appreciated. The information received will help me to go further as such I have submitted a 5 start rating for your first reply.
That sounds promising about the LMS part so yes, I stay tuned and wait patiently.
Ok, now let’s revert to the actual topic discussed here. Cisco Prime Service Catalog and Process Orchestrator solutions I have briefly read up on this on CCO (where elseJ) and picked out the following quote
---- Quote from the Cisco Prime Service Catalog Data Sheet
Today’s end users want self-service and easy access to IT tools and services.
Simultaneously, organizations are seeking ways to extend their cloud management
platforms beyond self-service delivery of virtual machines and infrastructure resources
while increasing their use of cloud-based solutions to enhance business agility and effectiveness.
Cisco Prime™ Service Catalog offers tremendous benefits to organizations that want to unify the ways in
which all types of IT services are ordered and fulfilled, not just infrastructure requests
---- un quote ---
I try to understand what (at high level of course) happens in the back ground when an order is raised and which vendor solution your product can interact with.
As mentioned in the quoted text, this service catalogue goes beyond the standard infrastructure.
Let’s say, a user wants to deploy a new email services, or in your example, extends or create a new web-portal (i.e. for HR to view and manage holiday, staff absence and benefits).
Your solution will need to interact somehow with the 3rd party vendor application that is capable building such portal I believe.
Without disclosing to many information, I assume the portal is linked to backend VM,s that spin up requested resources (and more magic of course). Perhaps I am mixing this up with another cisco product where a user can go on the portal and spin up virtual Firewalls, virtual Routers can be provisioned in now time.
Out if interest; Is this product also known as Mozart? (project code within Cisco?)
I hope query is ok.
Best wishes
Markus

Prime 1.3 and WLC 7.6 Can I push guest accounts?

Hi all
My Customer needs to update the WLC to 7.6 (from 7.4) due to 3700 APs, but does not use the ac or other new features (yet).
He has a Prime 1.3 update 4, where the guest Account are created.
Can he, after the WLC Upgrade to 7.6.130.0 still see the WLC from Prime 1.3 and Push guest accounts to the WLC?
The migration to PI 2.1 will be planned.
Thanks
Willem

Cisco Prime 1.3 doesn't support 7.6 please check the compatibility matrix
Table 4 Cisco Prime Infrastructure and Cisco Wireless Release Compatibility Matrix
Cisco Prime Infrastructure
Cisco WLC
Cisco MSE
ISE
Remarks
Update 4 for 1.3.0.20
Update 1 for 1.3.0.20
1.3.0.20
7.4.121.0
7.4.110.0
7.4.100.60
7.4.100.0
7.3.112.0
7.3.101.0
7.2.115.2
7.2.111.3
7.2.110.0
7.2.103.0
7.0.250.0
7.0.240.0
7.0.235.3
7.0.235.0
7.0.230.0
7.1.91.0
7.0.220.0
7.0.116.0
7.0.98.218
7.0.98.0
7.4.121.0
7.4.110.0
7.4.100.0
7.3.101.0
7.2.110.0
7.2.103.0
7.0.240.0
7.0.230.0
7.0.220.0
7.0.201.204
7.0.112.0
7.0.105.0
1.0
1.1
1.2

What is the difference in the features between Cisco prime 1.2 and Cisco prime 1.4 ?

Dears,
Please i need to know what is the difference in the features between Cisco prime infrastructure 1.2 and Cisco prime 1.4.
Already i see the release note for each one but the release indicate only the New feature for every one. so i need to know the difference between them not new features.
Wait your kind feedback plz
Regards,

Hi,
New Features and Enhancements
The following topics describe new features and enhancements in Cisco Prime Infrastructure 1.4.
Management Support for WLC Release 7.5
Support for 802.11ac Module
Support for Cisco AP 700
Policy Classification Engine
FlexConnect Audit Support
Autonomous AP Support
Client Stateful Switchover
Cable Modem Monitoring
Support for Secure File Transfer Protocol
and please go through the link and check the data sheet for further clearance.
http://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/prime-infrastructure/datasheet-c78-729879.html

Cisco 4500X VSS & MEC Cisco 2960X

Hi
I have Cisco 4500x VSS connect to MEC Cisco 2960X using LACP.
I encountered a problem about C2960X
Integration reason
1.C2960X Ten 1/0/2 link flapping interface error-disable . I am  disable interface then enable interface , switch show SFP not Present .
Te1/0/2 notconnect 1 full 10G Not Present. (SPF plug-in  Correct)
2.use CLI reload C2960X , Ten 1/0/1 ,Ten 1/0/2   notconnect SPF Not Present.  (SPF plug-in  Correct)
error message :
Dec 18 12:40:25.250: %SYS-5-CONFIG_I: Configured from console by console
Dec 18 12:41:48.888: % ILET-1-AUTHENTICATION_FAIL: This Switch may not have been manufactured by Cisco or with Cisco's authorization. This product may contain software that was copied in violation of Cisco's license terms. If your use of this product is the cause of a support issue, Cisco may deny operation of the product, support under your warranty or under a Cisco technical support program such as Smartnet. Please contact Cisco's Technical Assistance Center for more information.
26F_guest_switch#show license
Index 1 Feature: lanlite
        Period left: 0 minute 0 second
Index 2 Feature: lanbase
        Period left: Life time
        License Type: Permanent
        License State: Active, In Use
        License Priority: Medium
        License Count: Non-Counted
3.C2960X power Cycle ,C2960X  operation normal, ,but recurring problems every day.
I do not know where the problem , I have upgrade C2960X IOS but it had same problem.
Cisco 2960X IOS version:  15.2(3)E C2960X-UNIVERSALK9-M
Cisco 4500X IOS version: cat4500e-universalk9.SPA.03.05.00.E.152-1.E.bin
Thanks for your help,

Hi Reza,
Thanks for your help
I can not confirm that because I have a few switch have the same problem.
C2960X 10G port 1 is connected to C4500X slot 1, Port 2 is connected to C4500X Slot2.
link flapping, On the switch port 2.
I need to do a more precise test to confirm the problem is C2960X or 4500VSS

Prime 2.2 and 2960-X Edit Switchport Config all grayed out

Hi,
I have Prime 2.2 deployed and working well for our 4500X's and 2960-S's however for a pile of 2960X-24PD-L and 48-FPD-L when we go Configure -> Network Devices -> <switch> and select "Switchports" to make changes for example to the access VLAN of the port, everything on the page is grayed out.
The other 2960-S and 4500X's allow us to change, inventory and sync is completing properly - any ideas?
Rob

Hi Afroz appreciate you getting back to me so quickly, already have device pack 2.24 on the instance unfortunately.
Initially the 2960X would not display Switchports under the configuration tab however after a restart of NCS and a full sync, it did (yes I had rebooted post device pack install) however it just shows port information greyed out.
On the 3750X if you edit a gigabit switchport, some ports will show greyed out, others are editable.
It's like its read only which doesn't make sense?
Rob

VSS support

I've just started evaluting JDeveloper and like it so far. One thing I was wondering is if there are any Visual Source Safe support - something I need to have unfortunately.
I only find CVS as default and Google didn't help me out there, maybe someone here knows about it?
Best regards
Stefan

No VSS support right now.
We do have support for CVS, Clearcase, Perforce, and Serena Dimension.
(see the help->check for updates).
Support for Subversion and Windows Team Server is being developed right now.
For a simple way to integrate with third party version control tools see this one:
http://www.oracle.com/technology/products/jdev/101/howtos/extools/subversion.html

Had a recent crash on my macbook, was previously using OS 10.6 I think. Restored from recent Time Machine backup and updated to OS 10.8.2 and now I cannot open Logic Pro 9. I get a 'No entry' Icon and a not supported on this type of Mac message. I cannot

Had a recent crash on my macbook, was previously using OS 10.6 I think. Restored from recent Time Machine backup and updated to OS 10.8.2 and now I cannot open Logic Pro 9. I get a 'No entry' Icon and a not supported on this type of Mac message. I cannot update either as anything up to 9.1.1 tells me I don't need it yet 9.1.2 tells me I need an eligable Logic Pro Version was not found in applications.
All of my files are stored in a separate hard drive with only the actual app having been on my Macbook. Should I just reinstall?

Hi
To run Mouitain Lion you need to update Logic.
For the updaters to work the Logic application must be:
a) Within the Applications folder, and not in any sub-folder
b) Named "Logic Pro" with no extra numbers or spaces
CCT

Prime 2.1 and 4500X-VSS support?

Similar Messages

Maybe you are looking for