Prime Infrastructure 1.2 - Software Image Management

Good Day,
I have some issues with CPI 1.2. I've tried to Import Images from Cisco.com through Software Image Management
for test purposes by using my credentials. But it has finished success just a twice. Other attempt hadn't any result.
Then I try to choose Image for my test 3750E switch, sometimes I have error message like bellow:
After I choose another image and return to first that I need, and press <Submit>, I have a message that "Image collection job CCO Image Collection Job is Scheduled Successfully":
I wait some time and refresh, but I don't see any new Images. The same problem exist then I try Import Images from connected Devise. I use Shedule Start Time - Now.
Also, I can't view any information about Image in Device Work Center:
Any ideas, guys?

I'm having the same issue. I'm thinking there are still a lot of bugs in PI that Cisco needs to work out. LMS is still the better option for now in managing your switching environment. I know that Cisco hopes to role all device management under the umbrella of PI, but they still have some bugs to workout IMO.

Similar Messages

LMS Software Image Management - Telnet failure

Hi all,
I had a problem with Software Image Management for the upgrade of a switch.
It seems that at the end of the upgrade, CiscoWorks was unable to save the configuration with telnet.
Yet, telnet seems to be ok because CiscoWorks manages to connect to the switch at the beginning of the upgrade.
Updating config file during software upgrade processDevice running-config is modified but failed to save the running-config to startup-config.Cause: Could not detect SSH protocols running on the device
TELNET: Failed to establish TELNET connection to 10.1.3.4 -Cause: Authentication failed on device 3 times.
I sent attached the logs of the upgrade.
Thank you in advance.

Hello,
The job fails last night after timeout.
I have reschedule job this morning for 2 switchs :
2960 with telnet and ssh enabled
2960 with telnet enabled only
The device credentials verification job seems to be coherent :
Device Name
Read
Community
Read Write
Community
Telnet
Enable
by Telnet
SSH
Enable
by SSH
1.
switch04-d
Ok
Ok
Ok(Primary Successful)
Ok(Primary Successful)
Failed to connect.
Did Not Try
1.
switch03-d
Ok
Ok
Ok(Primary Successful)
Ok(Primary Successful)
Ok(Primary Successful)
Ok(Primary Successful)
But the job fails again cause telnet authentication failed on device 3 times.
I do not understand why LMS does not use ssh if possible at the finish of the job? Why telnet authentication fails ?
Thanks in advance.

Software Image Management in Prime LMS 4.2.3

In Software Repository Management I have added all the running images from our estate. The Status of each image is showing as "Not Available" even though I get the message "Image Status retrieved from Cisco.com successfully." when selecting Update Status. Should I see something more meaningful here?
Also when I run Patch Distribution I get "Failure" across the board - can anyone suggest a likely reason for this?

Hi Dave,
If your Goal is to upgarde the IOS of the devices via LMS then MANUALLY download the IOS Image from cisco.com
and use the FILE SYSTEM option to add the Image in the Software Repository
Then try to upgrade the IOS and see how it works.
Thanks
Afroz

Prime Infrastructure 1.1 software

Hi Experts,
I am working in a project needs Cisco prime infrastructure and the sales department already bought v1.1 R-PI-1.1-100-K9, but I don't have the CD for software, how can I get the software for this version 1.1.
Thanks
Mohammad Saeed

1.1 is very out of date - over 3 years old - and not even available on cisco.com anymore. Are you sure that is the version that was purchased? It has not been sold for several years.
The oldest 1.x release still available on cisco.com is 1.3.
If they bought support with upgrade entitlement, you are entitled to run the current software (2.2.1 is the current release). You would download and install 2.2 and patch it with 2.2.1 and latest device packs to get a current installation.

Cisco Prime Infrastructure 2.0 import image via WAN link failed.

Cisco Prime Infrastructure 2.0 behind NAT that can copy image on device to Cisco Prime infra but can not deploy from Cisco Prime Infra import image from device. How to solve problem,please ?

Have you downloaded and applied the latest Device Pack updates?
PI enhanced ASA support after the initial 2.0 release and the Device Packs incorporate that change.
The README file for Device Packs explains how to install them. (A bug currently does not allow the direct download in PI so you need to follow the method for installation from local storage after you manually download. Here is a link to the download location.

Prime Infrastructure 2.0 Software IOS deployment problems

When I try to deploy an IOS using the software deployment in Cisco PI 2.0 the jobs always fail. I have tried many different configurations and even switched flash cards but nothing works. The TFTP/SCP jobs always fail. Doing a "show flash:" I can see the image begin to copy, but it suddenly disappears and the job fails.
Any help would be very appreciated, this is very frustrating!!
Here is the failure message:
SWIM1125: Failed to copy the image to Flash due to the reason - copyUnknownFailure :failure unknown. Retry the operation. If the problem persists, check the Bug Toolkit application for any known issues on the running image version.Error loading image to flash.Image Copy Operation Failed
Thanks very much.

I solved my issue by running looking at the debug output on the 2811 router I was pushing the IOS (.bin file) to. I noticed that the TFTP traffic would simply stop without warning and seemingly for no reason. I gave up on the TFTP and had to configure the router for SCP instead (aaa new-model, etc.). The image would successfully copy from the prime server to flash after that.
The failure output from prime was very unhelpful for both tftp and scp failures. It wasn't until I did some SCP configuration reading that I realized I had SCP configured wrong. Still no idea why the TFTP wouldn't work.

Prime Infrastructure 2.0 Software Deployment VSS Systems

Good day -
Has anyone used the PI 2.0 Software Deployment with VSS systems like 6500 or 4500? Does it work? Does it upgrade the image in eFSU? Should VSS systems be manually updated?
Finally are there any guides or documentation on using PI 2.0 to deploy / upgrade images for platforms like 6500 / 4500 running VSS mode?
Thanks,
John

there is a Feature Enhancement BUG filed for VSS support
Unable to add or manage a 6500 in VSS in PI:
https://tools.cisco.com/bugsearch/bug/CSCuj09930/?reffering_site=dumpcr
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors ****

Prime Infrastructure 2.1. Image destribution problem.

Hello! I have a problem with distribution IOS on Cisco devices. PI version is 2.1.
I have the image on local repository. When i try to distribute it on any devise i receive the following error (space on the flash enough):
On Prime web interface - Jobs Dashboard:
SWIM5018: Copy operation Failed. Probable Causes : 1. Connection Time out. 2. Disk Space full. Recommended Action: 1.Please check the connectivity of the device. 2.Check if enough space is available for copy operation.Error loading image to Flash.For more details please check /opt/CSCOlumos/conf/ifm/swim/jobs/10.10.10.10_tftp_telnet.log for the output from the device on which the image transfer failed.Image Copy Operation Failed
On Prime log repository - /opt/CSCOlumos/conf/ifm/swim/jobs/10.10.10.10_tftp_telnet.log:
ade # vi 10.10.10.10_tftp_telnet.log
dir /all flash:
Directory of flash:/
    2 -rwx     6918153   Mar 1 1993 00:55:38 +00:00 c2970-lanbasek9-mz.122-44.SE.bin
    4 -rwx        4014   Mar 5 1993 23:45:28 +00:00 private-config.text
    5 -rwx        5324   Nov 8 2012 07:44:00 +00:00 vlan.dat
    6 -rwx        7560   Mar 1 1993 01:54:28 +00:00 23052014.cfg
    7 -rwx        5144   Mar 5 1993 23:45:28 +00:00 multiple-fs
    8 -rwx        3828   Mar 5 1993 23:45:28 +00:00 config.text
15998976 bytes total (9052160 bytes free)
HOSTNAME#copy tftp://10.5.5.5//c2970-lanbasek9-mz.122-44.SE6.bin flash:c2970-lanbasek9-mz.122-44.SE6.bin
Destination filename [c2970-lanbasek9-mz.122-44.SE6.bin]? c2970-lanbasek9-mz.122-44.SE6.bin
Accessing tftp://10.5.5.5//c2970-lanbasek9-mz.122-44.SE6.bin...
Loading c2970-lanbasek9-mz.122-44.SE6.bin from 10.5.5.5 (via Vlan110): !... [timed out]
%Error reading tftp://10.5.5.5/c2970-lanbasek9-mz.122-44.SE6.bin (Timed out)
HOSTNAME#disable 1
HOSTNAME>
HOSTNAME>
HOSTNAME>_tune_^H ^H^H ^H^H ^H^H ^H^H ^H^H ^H
HOSTNAME>
As i see, there is a TFTP timeout on session from Prime.
I've seen topics related to this, but I have not found an acceptable solution. Tell me, is there any way to solve this problem?
Thanks in advance

I am trying to update switch software with prime, and I am finding it to be quite cumbersome!
Any idea on this issue?

IOS Software Image Management

Hi,
I have encouter this problems when I was doing image retreival for certain device.
Attached are the problems faced
Anyone know the cause?

Hi Dave,
If your Goal is to upgarde the IOS of the devices via LMS then MANUALLY download the IOS Image from cisco.com
and use the FILE SYSTEM option to add the Image in the Software Repository
Then try to upgrade the IOS and see how it works.
Thanks
Afroz

WCS and LMS to Cisco Prime Infrastructure 1.3 Upgrade

Hello,
Our customer is currently having WCS for 500 devices and LMS 3.2 for 1500 devices. We are planning to upgrade to Cisco Prime Infrastructure 1.3.
I want to check is the upgrade procedure that we have planned is ok or we have missed something.
Phase 1: WCS to CPI 1.3 upgrade
1. Check that WCS is at 7.0.230.0 version
2. Export WCS database
3. Install NCS 1.1.1.24 software
4. Contact cisco to obtain trial license for NCS software (L-WCS-NCS1-M-K9 license).
5. Migrate WCS license and import it in NCS software
6. Migrate WCS data to NCS software using ncs migrate command
7. Patch NCS software
8. Inline upgrade to CPI 1.3 software
9. Install proper licenses on CPI 1.3 (WCS and LMS device count)
My concern in this first phase is should I use NCS large image since our Cisco Prime Infrastructure 1.3 software should manage 2000 devices at the end.
Or is it better not to perform inline upgrade and insted go with exporting data from NCS and then importing them to CPI 1.3 that is going to be installed separately?
Phase 2: LMS 3.2 to CPI upgrade
1. Export LMS 3.2 database
2. Install LMS 4.2 software
3. Install license to LMS 4.2
4. Restore data from LMS 3.2 to LMS 4.2
5. Direct upgrade from LMS 4.2 to 4.2.2
6. Export the device list with credentials from LMS 4.2.2 and import it as a Bulk Import in CPI 1.3
At the end we will have CPI 1.3 and LMS 4.2.2 software running.
Is it possible to directly upgrade from LMS 4.2 to LMS 4.2.4 and then import data to CPI 1.3 or we need to go with 4.2.2 version?
Regards,
Jelena

Hello Marvin,
We have restored LMS 3.2 SP 1 database on LMs 4.2 and we have got some error messages during restore. Please see our restore output:
[kalms4/root-ade ~]# /opt/CSCOpx/bin/perl /opt/CSCOpx/bin/res
resolver.pl           restoreDBTableMig.pl restoreJRMMig.pl      restorebackup.pl
[kalms4/root-ade ~]# /opt/CSCOpx/bin/perl /opt/CSCOpx/bin/restorebackup.pl -d /opt/BKP/
Restore started at : 2013/12/05 14:11:58
Please see '/var/adm/CSCOpx/log/restorebackup.log' for status.
     USER ID is ..................................... : sysadmin
     OS of the backup archive is..................... : Windows
INFO:The backup archive is from a different OS. Your current Platform is: Soft Appliance .
You are attempting to perform a Cross Platform Restore..
Do you wish to continue (Y/N) [Y] :Y
     Generation to be restored is ................... : 0
     Backup taken from............................... : /opt/BKP/
     Common Services version in the backup data is... : 3.3.1
     Common Services is installed in................. : /opt/CSCOpx
     The temp folder for this restore program........ : /opt/CSCOpx/tempBackupData
     Applications installed on this machine ......... : [Common Services][Campus Manager][Resource Manager Essentials][Device Fault Manager][cwportal][ipm][upm][cvw][cwlms]
     Applications in the backup archive ............. : [Common Services][Campus Manager][Resource Manager Essentials][Device Fault Manager][opsxml][cwportal][ipm][upm][cvw]
     WARNING: The list of applications installed on this CiscoWorks server does not match the list of
              applications in the backup archive. If you restore data from this backup archive,it may
              cause problems in the CiscoWorks applications.
              Do you want to continue the restore operation? (y-continue or n-quit, y/n)?Y
     Applications to be restored are................. : [Common Services] [Campus Manager] [Resource Manager Essentials] [Device Fault Manager] [cwportal] [ipm] [upm] [cvw]
     Available disk space in NMSROOT................. : 86451488 Kb
     Required disk space in NMSROOT.................. : 35906524 Kb
     (The temp and NMSROOT are on same device, therefore this required disk space includes temp space)
Copying the backup files to the temporary location [/opt/CSCOpx/tempBackupData]
preRestore of [Common Services] has started.
preRestore of [Common Services] has completed.
preRestore of [Campus Manager] has started.
preRestore of [Campus Manager] has completed.
preRestore of [Resource Manager Essentials] has started.
preRestore of [Resource Manager Essentials] has completed.
preRestore of [Device Fault Manager] has started.
preRestore of [Device Fault Manager] has completed.
preRestore of [cwportal] has started.
preRestore of [cwportal] has completed.
preRestore of [ipm] has started.
preRestore of [ipm] has completed.
preRestore of [upm] has started.
preRestore of [upm] has completed.
preRestore of [cvw] has started.
preRestore of [cvw] has completed.
doRestore of [Common Services] has started.
          Cross Platform Update started.
          Cross Platform Update completed.
          License check started.
             WARNING: The license details in the server are different from the backup data.
                      After restoring, please check the license available in the server.
             WARNING: Your current license count is lower than your earlier license count.
                      If you restore the data now, devices that exceed the current licence count
                      will be moved to Suspended state.
          License check completed.
          Restoring certificate.
             WARNING: Cannot evaluate the hostname, hence the certificate
                      may be from this host or another host.
                      [ Certificate not overwritten ]
          Restored Certificate.
          Restoring Common Services database.
          Restored Common Services database.
          Restoring CMIC data.
          Restored CMIC data.
          Restoring CMC data.
          Restored CMC data.
          Restoring Security Settings.
          Restored Security Settings.
          Restoring DCR data.
          Restored DCR data.
          Restoring Certificate key store.
          Restored Certificate key store.
Restoring DCNM CrossLaunch data.
          Restored DCNM CrossLaunch function.
          Restoring JAAS configuration.
          Restored JAAS configuration.
          JRM Job Migration started.
          JRM job Migration done.
doRestore of [Common Services] has completed.
doRestore of [Campus Manager] has started.
          Cross Platform Migration for Campus started.
Cross Platform update Starts for Campus
doRestore of [Campus Manager] has completed.
doRestore of [Resource Manager Essentials] has started.
10% of RME Restore completed
30% of RME Restore completed
50% of RME Restore completed
70% of RME Restore completed
100% of RME Restore completed
doRestore of [Resource Manager Essentials] has completed.
doRestore of [Device Fault Manager] has started.
10% of DFM Restore completed
30% of DFM Restore completed
50% of DFM Restore completed
80% of DFM Restore completed
Going to modify Eight PM report
Modified Sucessfully Eight PM report
100% of DFM Restore completed
doRestore of [Device Fault Manager] has completed.
doRestore of [cwportal] has started.
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.properties ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.script ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.log ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties//defaultUserCommunity.properties ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties//defaultCommunity.properties ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
doRestore of [cwportal] has completed.
doRestore of [ipm] has started.
        10% of IPM Restore Completed
        30% of IPM Restore Completed
        50% of IPM Restore Completed
        60% of IPM Restore Completed
        70% of IPM Restore Completed
        100% of IPM Restore Completed
doRestore of [ipm] has completed.
doRestore of [upm] has started.
HUM database restore starts
INFO:STOP= /opt/CSCOpx/objects/db/bin64/dbstop -q -y -c dsn=upm
SQL Anywhere Command File Hiding Utility Version 10.0.1.4239
INFO: Database Shutdown is in Progress..Please wait
INFO: Stop Engine Args= /opt/CSCOpx/objects/db/bin64/dbstop -q -y -c dsn=upm
INFO: After Database Shutdown RC= 2304
root=C:\PROGRA~2\CSCOpx\databases\upm\upm.db
DBUTILS: Inside Cross Platform
INFO: Current Database password does not match the password of Database being restored
INFO: Using the Password of the Database being restored
HUM database restore successfully completed.
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Threshold
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Threshold/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Custom
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Custom/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller_Failure
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller_Failure/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/TrendWatch
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/TrendWatch/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Availability
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Availability/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPORTUtilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPORTUtilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Utilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Utilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Memory_Utilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Memory_Utilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Availability
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Availability/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Threshold_Violations
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Threshold_Violations/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/CPU_Utilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/CPU_Utilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPSEConsumption
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPSEConsumption/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_ErrorRate
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_ErrorRate/README.txt
Directory is reportsStarted changing property .
linux
Restored HUM configuration file successfully.
doRestore of [upm] has completed.
doRestore of [cvw] has started.
doRestore of [cvw] has completed.
postRestore of [Common Services] has started.
postRestore of [Common Services] has completed.
postRestore of [Campus Manager] has started.
postRestore of [Campus Manager] has completed.
postRestore of [Resource Manager Essentials] has started.
postRestore of [Resource Manager Essentials] has completed.
postRestore of [Device Fault Manager] has started.
postRestore of [Device Fault Manager] has completed.
postRestore of [cwportal] has started.
postRestore of [cwportal] has completed.
postRestore of [ipm] has started.
postRestore of [ipm] has completed.
postRestore of [upm] has started.
postRestore of [upm] has completed.
postRestore of [cvw] has started.
postRestore of [cvw] has completed.
Restored successfully.
Are this errors going to affect our LMS 4.2 operations?
Then we have upgraded to LMS 4.2.2 and exported data and credentiales for PI import.
On PI 1.3 we have installed WCS 500 devices upgrade license and LMS 1500 upgrade license and now we are having 2000 devices lifecycle license. We have successfully restored WCS data in PI and we have imported LMS devices as bulk import. What is strange is that we have this message in prime regarding licensing:
On LMS 3.2 our customer had saved unlimited number of configuration versioning. After upgrading to LMS 4.2 we can only see last 3 configurations regardless of unlimided number of configurations in previous LMS, so my question is where can we find older configurations in LMS 4.2?
We are planning to turn unlimited versioning on CPI 1.3 now, so our customer will again have feature that they need. Do you have some experiance regarding disk space when all device configurations are stored forever?
Thank you for your help.
Regards,
Jelena

Cisco Prime 1.2 and image management

Does Cisco Prime 1.2 have the ability to work with image management? I was told yes but I do not see the options and I have verified I have the correct license...

Hi,
Go to Operate > Device work Center > software Image Management
check the below link:
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/1.2/user/guide/maint_images.html
Thanks-
Afroz
[Do rate the useful post]

Upgrade Cisco Prime LMS 4.0 to Cisco Prime Infrastructure 2.1

My company has asked me to migrate Prime LMS 4.0 to Prime Infrastructure 2.0 for a client and can not find the guide, the questions are? the migration is possible without an intermediate step? and There is a guide to update LMS 4.0 to PI 2.0 ??
Thanks in advance.

Prime LMS 4.2.2 added support for the PI template directly:
Export Data for Prime Infrastructure
Cisco Prime LAN Management Solution supports data migration to Prime Infrastructure 1.2. This feature enables user to export the Device Credentials Repository (DCR) data from LMS 4.2.x versions to Prime Infrastructure 1.2. The data backup status and backup location are displayed at the bottom of the Export Data for Prime Infrastructure page. The data being exported from LMS and the data imported back to PI are listed as follows.
Data exported from LMS
•Device Credentials Repository (DCR)
•Software Image Management
•Config Archive
•Change Audit
•Syslog
Data Imported to PI
Device Credentials Repository

Prime Infrastructure 1.1 LMS and NCS installation.

Dear all
I have purchase below mention product. Now my question is that.
A> 1). Prime (2). LMS 4.2 (2). NCS 1.1 are they different software and has to install them separately ?
B> or The prime is the only virtual(.ova) software where there LMS and NCS works as a feature?
C> Please help me with the download link and installation guide..
CISCO
R-PI-1.1-K9
Cisco Prime Infrastructure 1.1
CISCO
R-PI-1.1-100-K9
Prime Infrastructure 1.1 Software - 100 Device Base Lic
CISCO
L-PILMS42-100
Prime Infrastructure LMS 4.2 - 100 Device Base Lic
CISCO
L-PINCS11-100
Prime Infrastructure NCS 1.1 - 100 Device Base Lic
CISCO
L-PINCSW11-100
Prime Infrastructure NCS WAN 1.1 - 100 Device Base Lic
With Regards
Tanmay
[email protected]

SOme of the similar discussion happened here, which would be helpful.
To answer your questions :
A.> Yes all three of them are separate software.
LMS :--> Ciscoworks Prime LMS is about to be end-of-life software which will phase out in favour of its successor Cisco Prime Infrastructure. This Software was the key application from Cisco to help manage the entire Wired Infrastructure for cisco devices, like Routers, switches, VPN, FW's, etc.
NCS:--> Wireless Control System (WCS) was the LMS equivalent software to manage Cisco's wireless infrastructure. It evolved as a new Generation Network Control System (NCS).
Cisco Prime Infrastructure :--> Cisco felt market demand to have a unified experience to manage both Wired and Wireless Infrastructure, hence Cisco Prime Infrastructure was introduced which is NCS+LMS. Not all features of LMS are migrated, hence customer's are allowed to use LMS latest version 4.2.x for wired network devices, if required.
B.> Prime is now provided with an inbaked Linux kernel to remove dependency from Windows or Unix (Solaris) OS, hence it is only available as OVA deployment image to be used under virtualized environment and can take benefit of virtualized infrastructure.
FOllowing are the download links :
Download LMS 4.2 here
Download PI 2.1 here
-Thanks
Vinod
**Encourage Contributors. RATE Them.**

Cisco Prime Infrastructure 2.0 and ASA 55xx platform

Hello,
We recently upgraded to Prime Infrastructure 2.0 with the hope being able to manage our ASA's from PRIME (and complete an LMS migration).
When I attempt to add ASA's to prime i get the following collection errors:
Unable to collect processor and RAM information.          Processor and RAM information.          Unexpected error. See the log file inventory.log for details.
In the logfile I get the following XML parsing error on the MIB:
<palError>
<deviceId>6284310032</deviceId>
<code>VALIDATION_ERROR</code>
<message>Failed to validate output XML: cvc-maxInclusive-valid: Value '3484331296' is not facet-valid with respect to maxInclusive '2147483647' for type 'int'.</message>
<result>
    <result xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="/CISCO-MEMORY-POOL-MIB/xmp-im-file-system-module.xsd">
      <xmp-im-file-system-module>
        <MemoryPoolStatistics>
          <memoryPoolIndex>1</memoryPoolIndex>
          <free>4294967295</free>
          <largestFree>4294967295</largestFree>
          <used>3484331296</used>
        </MemoryPoolStatistics>
To me it seems that the ASA returns a value that is bigger then int32 and thus causes an overflow? Any clues? Workarounds to add an ASA to Prime without checking these MIB'S?
Regards,
Marcel

The X series (all with 64-bit SMP images) are not currently supported by PI 2.0. We can hope for a device update in the coming months to remedy that situation.
If you click on the arrow next to the help icon in the top right of your PI and choose "Device Level Support" you will see:
Cisco ASA-5500 Series Adaptive Security Appliances
Features :
Topology
LLDP Neighbor Discovery
CDP Neighbor Discovery
Configuration
Configuration Archive
Software Image Management
Monitoring
Device Availability
Reachability
Inventory
Physical
System - Memory Pools
Interfaces - IP
Interfaces - Ethernet
Device Type
SYSOIDS
S/W Version
Software
Cisco ASA-5510 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.669
OID:1.3.6.1.4.1.9.12.3.1.3.447
Cisco ASA-5510 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.773
Cisco ASA-5520 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.670
OID:1.3.6.1.4.1.9.12.3.1.3.448
Cisco ASA-5520 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.671
Cisco ASA-5540 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.672
OID:1.3.6.1.4.1.9.12.3.1.3.449
Cisco ASA-5540 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.673
Cisco ASA-5560 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.12.3.1.3.454
Cisco ASA-5550 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.753
Cisco ASA-5550 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.763
Cisco ASA-5505 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.745
OID:1.3.6.1.4.1.9.12.3.1.3.560
Cisco ASA-5580 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.914
Cisco ASA-5585 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.1194
OID:1.3.6.1.4.1.9.1.1195
OID:1.3.6.1.4.1.9.1.1196
OID:1.3.6.1.4.1.9.1.1197
Cisco ASA-5585 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.1198
OID:1.3.6.1.4.1.9.1.1199
OID:1.3.6.1.4.1.9.1.1200
OID:1.3.6.1.4.1.9.1.1201
Cisco ASA-5585 Adaptive Security Appliance System Context
OID:1.3.6.1.4.1.9.1.1202
OID:1.3.6.1.4.1.9.1.1203
OID:1.3.6.1.4.1.9.1.1204
OID:1.3.6.1.4.1.9.1.1205
Cisco ASA-5580 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.915
Cisco ASA-5580 Adaptive Security Appliance System Context
OID:1.3.6.1.4.1.9.1.916

Cisco Prime Infrastructure 1.2 with Cisco Prime Network Control System Hardware Appliance

Hi Team,
I have following BOM
Cisco Prime Infrastructure
R-PI-1.2-K9
Cisco Prime Infrastructure 1.2
1
R-PI-1.1-500-K9
Prime Infrastructure 1.2 Software - 500 Device Base Lic
1
L-PILMS42-500
Prime Infrastructure LMS 4.2 - 500 Device Base Lic
1
L-PINCS12-500
Prime Infrastructure NCS 1.2 - 500 Device Base Lic
1
PRIME-NCS-APL-K9
Cisco Prime Network Control System Hardware Appliance
1
PI-APL-IMAGE-1.2
Cisco Prime Infrastructure 1.2 Appliance Software
1
Pls let me know if we have both NCS and LMS preinstalled with Cisco Prime Infrastructure 1.2 Appliance Software orwe need seperate appliance or server for LMS 4.2.
Regards

Hi Scott,
Thanks for the response but I got to know that LMS and NCS are combined in single ISO image from PI 1.2 and can be installed on the same physical NCS appliance.
Can you pls check this.
Regards

Prime Infrastructure 1.2 - Software Image Management

Similar Messages

Maybe you are looking for