Prime Infrastructure 1.3 AP Groups missing

Where are the AP groups in PI 1.3 ?
The documentation in PI 1.3 states
Step 1 Choose Configure > Controller Template Launch Pad.
Step 2 Click AP Groups or choose WLAN > AP Groups from the left sidebar menu.
AP groups in the controller itself shows the applied template names, but there are no templates ???????

Have you looked using classic theme and not the default lifecycle theme. Click on the root on the top right and choose classic theme. Also you might need to discover templates from the controller as they don't sync the information.
Sent from Cisco Technical Support iPhone App

Similar Messages

Prime Infrastructure 2.0 Importing user-defined group rules

Dears,
I'm looking for a way to import rules to put devices in a user defined group.
I can see how I can create groups and rules manually, but not how I could export or import those rules.
Is this possible, or on the roadmap?
Cheers,
Michel

In the Cisco Prime Infrastructure 2.0 Deployment Guide under LMS 4.2 Data Migration there is a way to import settings from a "special" backup made from LMS.
This should allow for importing userdefined groups.
Does anyone have tried this yet?
Cheers,
Michel

Prime Infrastructure port grouping

Hi,
I have question regarding the port groups.
Is it possible to create a port group based on port type where the port type is a dot1q trunk?
In the drop down menu, I can only find Cisco ISL.
My goal is to apply the interface/port monitoring only on trunk interfaces/ports.
Regards
Joerg

This discussion will be of your help:
https://supportforums.cisco.com/thread/2239478
You can select the interfaces of your interest for port groups manually. Check the user guide here:
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/user/guide/setup_groups.html#wp1055433
P.S : In CSC it is always good to share the device and Cisco PI platform and version details. Many times you'll find features are supported in one release and not in others.
-Thanks
Vinod
**Rating Encourages contributors, and its really free. **

Prime Infrastructure 2.1 problem with sorting devices in device groups

Hi,
I have a problem with prime infrastructure, namely prime is not doing appropriate sorting of devices in default device groups.
Example: device type > routers > Cisco 2800 series integrated services routers - under shown results there are Cisco 2911 Integrated Service router, Cisco 2901 etc.
Any solution?
Tnx

Hi all:
I have tried using Designing Monitoring Template to set the Health Check Polling time from default 15 minutes to 5 minutes and also tried also 1 minute.
The result is 5 minutes is working but 1 minute is not working.
May I know any one can help on this?
Many thanks!
Best regards,
tangsuan

Cisco Prime Infrastructure 2.0 - no traps/info are pushed from devices

Good evening,
I have setup Cisco Prime Infrastructure 2.0 and, though I have added manually my 4 network cores as devices without any problem, I can't get a single trap or a single SNMP information to be pushed into my Cisco Prime Infra.
Here is my SNMP config on my core :
snmp-server user *edited* *edited* v3
snmp-server group *edited* v3 noauth notify *tv.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF0F
snmp-server community *edited* RO
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps flowmon
snmp-server enable traps transceiver all
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps rf
snmp-server enable traps memory
snmp-server enable traps cpu_threshold
snmp-server enable traps eigrp
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change nssa-trans-change
snmp-server enable traps ospf cisco-specific state-change shamlink interface
snmp-server enable traps ospf cisco-specific state-change shamlink neighbor
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps flex-links status
snmp-server enable traps fru-ctrl
snmp-server enable traps entity
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps ether-oam
snmp-server enable traps aaa_server
snmp-server enable traps flash insertion removal
snmp-server enable traps l2tc threshold sys-threshold
snmp-server enable traps power-ethernet police
snmp-server enable traps rep
snmp-server enable traps vswitch dual-active vsl
snmp-server enable traps udld link-fail-rpt status-change
snmp-server enable traps vtp
snmp-server enable traps vlancreate
snmp-server enable traps vlandelete
snmp-server enable traps auth-framework sec-violation
snmp-server enable traps dot1x auth-fail-vlan guest-vlan no-auth-fail-vlan no-guest-vlan
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps entity-diag boot-up-fail hm-test-recover hm-thresh-reached scheduled-test-fail
snmp-server enable traps port-security
snmp-server enable traps ethernet evc status create delete
snmp-server enable traps energywise
snmp-server enable traps ipsla
snmp-server enable traps vstack
snmp-server enable traps bfd
snmp-server enable traps bgp
snmp-server enable traps bulkstat collection transfer
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps ipmulticast
snmp-server enable traps isis
snmp-server enable traps msdp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
snmp-server enable traps syslog
snmp-server enable traps isakmp policy add
snmp-server enable traps isakmp policy delete
snmp-server enable traps isakmp tunnel start
snmp-server enable traps isakmp tunnel stop
snmp-server enable traps ipsec cryptomap add
snmp-server enable traps ipsec cryptomap delete
snmp-server enable traps ipsec cryptomap attach
snmp-server enable traps ipsec cryptomap detach
snmp-server enable traps ipsec tunnel start
snmp-server enable traps ipsec tunnel stop
snmp-server enable traps ipsec too-many-sas
snmp-server enable traps errdisable
snmp-server enable traps ethernet cfm alarm
snmp-server enable traps vlan-membership
snmp-server enable traps mac-notification change move threshold
snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down
snmp-server host *ip-address-edited* version 3 noauth *edited*
Basically all traps are enabled but absolutely nothing is showing up in my Prime Infra except that my 4 devices are "Reachable".
Here is a show snmp on the same device :
sh snmp
Chassis: *S/N Edited*
38554534 SNMP packets input
    0 Bad SNMP version errors
    14 Unknown community name
    0 Illegal operation for community name supplied
    0 Encoding errors
    38453185 Number of requested variables
    0 Number of altered variables
    17790703 Get-request PDUs
    20583581 Get-next PDUs
    0 Set-request PDUs
    0 Input queue packet drops (Maximum queue size 1000)
38490708 SNMP packets output
    0 Too big errors (Maximum packet size 1500)
    0 No such name errors
    0 Bad values errors
    0 General errors
    38371069 Response PDUs
    13 Trap PDUs
SNMP global trap: enabled
SNMP agent enabled
SNMP logging: enabled
    Logging to *edited*, 0/10, 13 sent, 0 dropped.
Can anyone point out what is wrong or missing in my configuration? I can't seem to single it out myself.
Thanks
Jeremy

Hi Jeremy,
SNMP traps are shown in the events and alerts section of PI.
SNMP config looks fine. Can you run the SNMP debug (debug snmp packets ) .check the logs and see if the device is actually sending the TRAPS to the PI server.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors ****

Cisco Prime Infrastructure 2.0 : Nms:RAID - RAID is Bad Detect rebuild progress

Hi,
I'm having problem on our Cisco Prime Infrastructure 2.0 which is always happen HDD failure.
FYI, HDD failed at Slot 1.
This is details of message taken from our Cisco Prime alarms;
raid is bad detect rebuild progress... enclosure = 252 enclosure = 252 drive 255 is missing or bad
For your information, I was enter into RAID BIOS to saw the error. I got Slot:1, SAS, HDD, 278.464GB, Failed.
I also do the Rebuild drives on that HDD. After Rebuild is completed the HDD back to ONLINE.
But I still face the same problem for the next day.
Please help us to resolved the problem.
Thanks and Regrads.
Mohd Syukri Kaus
BIT Group Sdn Bhd

You have the necessary CPU, memory and hard drive specifications for an Express size installation (Reference).
To install Prime Infrastructure 2.0 you will need to first install VMware ESX/ESXi. This is documented in the same Getting Started Guide I linked to above at this link.
Once you get that far along, just follow the setup wizard and installation is pretty simple.
FYI you will get better attention to Prime questions over in the Network Management forum.

Prime Infrastructure 2.1 - SFP port alarms to email/show total network traffic speed

Hello,
Running Prime Infrastructure 2.1 with assurance license.
I have two questions:
1. Setting up alarms in PI 2.1. I've set up a port group of my main switches that have TenGig links to our main router. I have set up a monitor template that has only interface availability on it and then deployed it. In theory, this should email me, the contact (where I put my email address in), when the ports that I have set up go down, correct?
2. I want to monitor the entire traffic of the network going in to the router from our TenGig ports. I've messed around with the dashlets and adding my port group to the WAN utilization dashlet but only see % of utilization. I'd like to be able to see raw traffic stats from those ports. I'm sure I'm missing something. Where do I need to look in PI to check raw traffic data in Mbps/Gbps from my ports.

In my first question, I do not get an email when a port goes down. I set up a test port and when I pulled it, after about 10 minutes, it had never sent me an email. I will continue to look through what I've been doing to see if I can figure it out.

Prime Infrastructure and WLC 2504 N+1 config syncronization

I've setup 2 cisco 2504 WLC's in a N+1 configuration, before we purchased Prime Infrastructure. Now I'm trying to syncronize the configurations between the two devices in PI. I've setup a configuration group, and it seems using templates will keep the configuration syncronized between the two devices. Is it possible for PI to automatically create the templates based on the current configuration of the device. Plus with PI 2.1 it seems like I have to create a template for every section of the configuration, shouldn't there be just one large template that has all the configurations.

Yes, you should be able to discover templates from the WLC
HTH,
Steve

When is Cisco Prime Infrastructure 2.0 released, and what does 2.0 offer?

We are running Prime Infrastructure 1.3 primarily for wireless management at this point. We have enough licenses to add all our switches, routers, and firewalls, but we're hesitant to do so until 2.0 comes out. While there are some features for backing up and configuring switches and routers, 1.3 still seems pretty limited in regards to non-wireless features. For example, nearly every report in 1.3 is for wireless controllers or AP's, there are no reports I've found relevent for switches and routers. I've read a lot of blogs, cisco posts, and white papers talking about how Cisco Prime Infrastrucure 2.0 will finally consolidate Prime into a truly all-in-one network management suite that can manage the entire Cisco environment. Does anyone know when it's officially being released? Does anyone have an tech sheets on what's new in 2.0, or what its capabilities are? I want to better understand what 2.0 has to offer, when it's coming out, how to upgrade, so I can start planning for the upgrade and eventually importing all our network devices to Cisco Prime for centralized management. Any useful information or links would be appreciated.
Thanks,
Christian

PI 2.0 is in Beta mode for testing in closed group already. However it may still take some time to get released on CCO for FCS.
I think it is expected to be released between aug-sep. BU has also started working on CPI 2.1, which you can see test uploads on CCO.
For what does it have for customers?
> As Cisco have a vision of one network Management software for both wired and wireless infrastructure, which started getting real partially with Cisco PI.
As WCS got evolved to NCS and eventually to Cisco Prime Infrastructure, but it doesnt yet have full Management capability for wired infra., which is there with LMS.
With CPI 2.x Cisco plans to blend entire LMS and WCS features together.
-Thanks

Prime Infrastructure 2.0 Job Approval notifications?

I have a question about notification for job approvers in Prime 2.0. I'm trying to setup PI such that a restricted user can create a configuration change on a wireless controller and submit it for approval by the PI admin.
The PI admin will likely not be logging in every day to check job approval status. I can't see anywhere that notifies the admin via email that a job is waiting. can this be done or am I missing something?
-Tim

Hi Tim,
I don't think we have an email optiom to notify the ADMIN to approve the pending jobs ,however if you authorized any job then ONLY admin can approve to run the job.
check the below link:
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/administrator/guide/config_server_settings.html#wp1081686
Thanks-
Afroz
[Do rate the useful post]

Prime Infrastructure 2.x tacacs+ with radiator

Trying to setup Prime Infrastructure 2.x (2.2) to use Tacacs+. The Tacacs service is running on a Linux server running Radiator(4.12). With Radius and Radiator all we needed to do is define the user group and all the tasks associated with that group were inherited.
When configuring the TACACs configuration files have tried various permutations of adding the cisco-avpair(cisco-av-pair) reply attrs on authentication and/or authorization. When defining the group or using the individual tasks I get the following error message:
"no authorization information found for remote authenttication user. please check the correctness of the associated task(s) and Virtual Domain(s) in the remote server"
<ServerTACACSPLUS>
Key SECRET
Port 49
GroupMemberAttr OSC-Authorize-Group
# General Authorization rule format:
AuthorizeGroup core-group permit protocol=HTTP service=NCS {cisco-av-pair="virtual-domain0=ROOT-DOMAIN" cisco-av-pair="role0=Super Users" }
</ServerTACACSPLUS>

It's not yet supported. Cisco doesn't generally publish roadmaps publicly for future support. The best you can do via public sources is to continue to watch the Supported Devices lists for updates.
As of right now, here is a list of the current data center switches supported (in PI 2.1):
Cisco Nexus 6004 Switch
Cisco Nexus 5596T Switch
Cisco Nexus 5010 Switch
Cisco Nexus 5020 Switch
Cisco Nexus 5020T Switch
Cisco Nexus 7000 10-Slot Switch
Cisco Nexus 7000 18-Slot Switch
Cisco Nexus 1000V Series Switches
Cisco Nexus 1010 Virtual Services Appliance
Cisco Nexus 4001I Switch Module for IBM BladeCenter
Cisco Nexus 4005I Switch Module for IBM BladeCenter
Cisco Nexus 5548P Switch
Cisco Nexus 5548UP Switch
Cisco Nexus 5596UP Switch
Cisco Nexus 3064 Switch
Cisco Nexus 3048 Switch
Cisco Nexus 3016 Switch
Cisco Nexus 7000 9-Slot Switch
Cisco Nexus 9500 Switch
Cisco Nexus 3548 Switch

Email Notifications on Prime Infrastructure 2.1

Hi Everyone,
I have a Cisco Prime Infrastructure 2.1 with almost 100 switches registered and managed properly. I have configured the Mail Server and alarm notifications are sent with no problems.
The deal is that I don´t want to recieve alarm mails for every single device that is registered. Is it possible to recieve mails just for a group of devices? I was checking the Cisco documents but could not find something clear about this.
Thanks for your help,
Ricardo

Hi Everyone,
I have a Cisco Prime Infrastructure 2.1 with almost 100 switches registered and managed properly. I have configured the Mail Server and alarm notifications are sent with no problems.
The deal is that I don´t want to recieve alarm mails for every single device that is registered. Is it possible to recieve mails just for a group of devices? I was checking the Cisco documents but could not find something clear about this.
Thanks for your help,
Ricardo

Cisco Prime Infrastructure 2.2 Rest API XML does not add LF

I am using several scripts that dig the data from XML files created through Cisco Prime Infrastructure Rest API. It worked fine until 2.1. Now, with 2.2, seems Cisco stopped adding LF to each line and everything is 'one' line.
Here is an example with 2.1, there is a LF to the end of each line:
?xml version="1.0" encoding="UTF-8" standalone="yes"?>
<queryResponse type="AccessPointDetails" rootUrl="https://server/webacs/api/v1/data" requestUrl="https://server/webacs/api/v1/data/AccessPointDetails?type=contains(UnifiedAp)&.full=true&.maxResults=1000&.firstResult=0" responseType="listEntityInstances" count="715" first="0" last="714">
    <entity url="https://server/webacs/api/v1/data/AccessPointDetails/1505569" type="AccessPointDetails" dtoType="accessPointDetailsDTO">
        <accessPointDetailsDTO id="1505569" displayName="1505569">
            <adminStatus>ENABLE</adminStatus>
            <apType>AP1240</apType>
            <cdpNeighbors>
                <cdpNeighbor>
                    <capabilities>Switch IGMP </capabilities>
                    <duplex>Half Duplex</duplex>
                    <interfaceSpeed>100Mbps</interfaceSpeed>
                    <localPort>2</localPort>
                    <neighborIpAddress>10.1.1.1</neighborIpAddress>
                    <neighborName>switch</neighborName>
                    <neighborPort>FastEthernet0/1</neighborPort>
                    <platform>cisco WS-C3560-8PC</platform>
                </cdpNeighbor>
Now, with 2.2, there is not LF anywhere:
?xml version="1.0" encoding="UTF-8" standalone="yes"?><queryResponse type="AccessPointDetails" rootUrl="https://server/webacs/api/v1/data" requestUrl="https://server/webacs/api/v1/data/AccessPointDetails?type=contains(UnifiedAp&.full=true&.maxResults=1000&.firstResult=0" responseType="listEntityInstances" count="715" first="0" last="714">
<entity url="https://server/webacs/api/v1/data/AccessPointDetails/1505569" type="AccessPointDetails" dtoType="accessPointDetailsDTO">
<accessPointDetailsDTO id="1505569" displayName="1505569"><adminStatus>ENABLE</adminStatus><apType>AP1240</apType><cdpNeighbors><cdpNeighbor>
Does anyone know, is this intentional or a mistake? Or is there a way how I control this?
I am reading on-line CPI Rest API docs, but seems cannot find anything.
Thanks,
Vlad

PI 2.0 is in Beta mode for testing in closed group already. However it may still take some time to get released on CCO for FCS.
I think it is expected to be released between aug-sep. BU has also started working on CPI 2.1, which you can see test uploads on CCO.
For what does it have for customers?
> As Cisco have a vision of one network Management software for both wired and wireless infrastructure, which started getting real partially with Cisco PI.
As WCS got evolved to NCS and eventually to Cisco Prime Infrastructure, but it doesnt yet have full Management capability for wired infra., which is there with LMS.
With CPI 2.x Cisco plans to blend entire LMS and WCS features together.
-Thanks

Using Windows Network Policy Server to authenticate Prime Infrastructure 1.4 admin access

I am using Prime Infrastructure 1.4 and I am needing to set up RADIUS Authencation. I am using Microsoft Network Policy Server. I have done all of the setup on both systems. I have matched up the settings the best I can on both systems. I am trying to use CHAP. I keep getting username or passwrod is not valid. In a effort to test I changed the Authentication type to PAP (I do not want to use this because it is not encrypted) But in a effort of testing I changed the setting on both the NPS and on Prime. I am now able to log in. Changing back to CHAP it fails and states the Username or Password is invalid. SO, PLEASE HELP!!!!

Ok, I was able to resolve this over the weekend. The actual fix is a little complicated. You can find the full explination here: http://technologyordie.com/windows-nps-radius-authentication-of-cisco-prime-infrastructure
The basics are that Prime (1.3 is the version I am using at this point) expects two AV pairs from radius. They are as as follows:
NCS:role0=Admin
NCS:virtual-domain0=ROOT-DOMAIN
"Admin" is the name of the group you would like your users to have access at and "ROOT-DOMAIN" is the name of the domain you would like them to have access to.
For TACACS+ I suspect the AV Pairs are going to be the same but I have not been able to test that.

Cisco Prime Infrastructure 1.2

Hello,
I have some maps of our building in PDF format and i want to load them on the cisco prime infrastructure 1.2, could you tell me how?
FYI: i opened : Design tab => Site maps Design but after this i don't know if i have to create a group or no;
Thanks

Thanks, i done it.
I have a problem to fill out some information in the New Floor Area tab:
our building has 1 basement and a ground floor and 3 floors, may I consider the ground floor as a the first floor because i have to fill out Number of floors on the edit building tab then i have to put 4 floors otherwise in the new floor area i'll have only 3 floors on the drop down list. (and the last floor will not has an id floor)
and the problem is
ground floor has floor id 1
1st floor has floor id 2 ......
have you any suggestion?

Prime Infrastructure 1.3 AP Groups missing

Similar Messages

Maybe you are looking for