Prime Infrastructure 2.0 and add a WLC device
Hi,
One question regarding to add a device / WLC Controller into NCS 2.0. I done this in the past with NCS 1.3 without problems
but now I don´t know why but if I add a device into the NCS 2.0 I get the the message CLI Failure / timeout.
I doublechecked all on the controller but I don´t see any failure . For my understanding I have to add a user under"Local Managmeent User " and then add this credentials into the Telnet/SSH Parameters on the NCS 2.0 .
Thanks for help.
Hi Scott,
Upto 7.3 config guide it was documented we have to reboot WLC when we configuring SNMP v3 which is wrong. (here is 7.3 config guide link for reference). May be older version (prior to 7.0) had that requirement, not too sure about it
http://www.cisco.com/en/US/docs/wireless/controller/7.3/configuration/guide/b_wlc-cg_chapter_0100.html#d16741e4514a1635
From 7.4 onwards config guide does not talk about it all. I deleted the default SNMPv3 user & create a new user in 7.4 & add it to prime without rebooting WLC.
Once you configureed a SNMPv3 user on a WLC, I do no think you can edit/change the password. You have to delete the user & recreate it with modified username/password.Then re-add the WLC to prime
The behaviour you mentioned is with any of later codes of WLC ?
Rasika
Similar Messages
-
Cisco Prime Infrastructure 1.2 and Aironet 1250 + VSS issues
Hi,
I am new to the NCS implementations and configurations. I have one very specific case with Cisco Prime Infrastructure 1.2 and autonomnous APs and several issues with Cisco VSS on 6500 switches.
So here is the version from Prime:
NCS/admin# show version
Cisco Application Deployment Engine OS Release: 2.0
ADE-OS Build Version: 2.0.1.038
ADE-OS System Architecture: x86_64
Copyright (c) 2005-2010 by Cisco Systems, Inc.
All rights reserved.
Hostname: NCS
Version information of installed applications
Cisco Prime Network Control System
Version : 1.2.1.012
IOS version on our APs (which are autonomnous) is:
AP-N-1>show ver
Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(25d)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 11-Aug-11 03:23 by prod_rel_team
Well the issue what we have now is that access point has been added but its not recognized by the NCS prime. I have tried all three versions of SNMP but I get the same result. The SNMP configuration is valid since I use the same for my switching infrastructure. When I enter "debug snmp packets" and "terminal monitor" I can see the SNMP communication between Prime and Aironet 1250 which is standalone.
When I switch to Lifecycle theme and go to Operate > Device Monitor Center I see all devices I have added. The Aironet 1250 is reachable but under collection status I get Managed with Warnings. When I hover over with my mouse I get "None available".
I have successfully added my switching infrastructure in total, which is operating perfectly for Catalyst 2960/3650/3750/4500 series but for 6500 under VSS I have some warnings. The device is recognized by the system which is excellent and all is operational. I get the following errors under Collection Status:
feature_sensor
SNMP request timed out
feature_powerSupplyFanStatus-6k
SNMP request timed out
IdentityCapability
The device is unreachable.
feature_flashdevice
SNMP request timed out
sam_ipsla_feature
The device is unreachable.
What can be done to resolve these issues ? I have attached a screenshot of this particular issue. The affected access point is 172.16.165.241.
Predrag PetrovicHi rajeeshp,
Currently I am not allowed to upgrade it because of internal procedures involved in upgrading a specific piece of software (obtaining permissions from various departments). Is it free to upgrade from 1.2 to 1.3 or there is a specific charge for that.
Predrag Petrovic -
WLC 5508, Prime Infrastructure, 7921 phones and QoS
Hi everybody!
I have deployed about 50 wireless cisco phones int the network with 27 APs with the WLC 5508.
I'm trying to investigate phones behaviour (I have some loss of audio).
And I use Prime Infrastructure for monitoring.
I run the Voice Diagnostic on the selected two phones.
and in the Charts I see the next:
1. for one phone "Downlink AC Queue Usage" shows all the traffic of "voice packets". but "Uplink AC Queue Usage" shows all the traffic of the "Best efforts packets".
2. for the second phone "Downlink AC Queue Usage" shows all the traffic of "Best efforts packets". and "Uplink AC Queue Usage" shows all the traffic of the "Video packets".
that is strange, very strange. the WLAN of these phones uses platinum QoS. none of other WLANs uses "gold" QoS.
does this mean I have a QoS misconfiguration?
where may the failure be? WLC? switches? router?
please, any suggestions...I noticed few misconfigurations as per your response
1. Are you configured AP as FlexConnect ? If not AP connected switchport should be configured as ACCESS port & trust DSCP. If it is configured as FlexConnect, then you can configure switchport as turnk & in that case you have to trust CoS using "mls qos trusct cos" command.
2. WLC connected trunk ports always to be configured to trust CoS not DSCP. Otherwise WLC set QoS value ignored by your switch.
3. If you WLAN is set for Platinum then you have to configure Platinum QoS profile for 802.1p & set value as 6.
I would suggest you to verify QoS value preserve across you switch network. You have to take some wireshark packet caputres (as shown in my reference link) and make sure your voice packet DSCP goes into rest of your network as EF. You need to do this for upstream & downstream (from 7921 perspective) traffic. Here is the traffic flow if AP connected to switchport 1 & WLC connnected to switchport 2.
7921 <-> AP <-> Switch port 1 <-> Switchport 2 <-> WLC <-> Switchport2 <-> Rest of your network
Once you do this, then you can go to Prime & check those charts to reflect QoS values correctly. Otherwise you do not know where these QoS value get stripped/or modified in your network.
HTH
Rasika
**** Pls rate all useful responses **** -
Setting up Prime Infrastructure to manage 2504 WLC, trying to add Lobby Ambassador and I get this error message:
User add failed : Some unexpected internal error has occurred. If the problem persists please report to the Tech Support.
Technically, this is my second attempt at setting up PI. I set it up initially with the wrong version of PI and created a lobby ambassador. I followed the instructions from the forum with a similar problem that said to remove the trap receiver on the WLC from my first attempt at installing PI.
https://supportforums.cisco.com/discussion/11110686/failed-add-device-wcs-reason-common-1-some-unexpected-internal-error-has-occured
I'm now able to add a Lobby Ambassador as long as its not the same username that I created on the previous PI setup. So I suspect this Lobby Ambassador username is somewhere on the 2504 WLC, but I can't find it anywhere to remove it.I have just been struggling with a similar issue on a fresh install of Prime 2.1 Upgraded to 2.1.1.
If I try to create the user with lobby ambassador role it just fails with "unexpected internal error".
I eventually found that by creating the user as a normal admin user first - the user is added. You can then go in a remove the admin role and change the role to lobby ambassador. This works with no internal error and the lobby admin user is working fine.
I would say it is just a bug. -
Prime Infrastructure 2.0 Automatically add remove devices
Dears,
I'm basically looking for a dcrcli equivalent to use on prime infrastructure 2.0.
Customer has a central repository of devices that must be monitored. When devices are added or removed there, they automagically appear or disappear in the other systems.
Does something like this exist or is this on the roadmap?
Cheers,
MichelHi Scott,
Upto 7.3 config guide it was documented we have to reboot WLC when we configuring SNMP v3 which is wrong. (here is 7.3 config guide link for reference). May be older version (prior to 7.0) had that requirement, not too sure about it
http://www.cisco.com/en/US/docs/wireless/controller/7.3/configuration/guide/b_wlc-cg_chapter_0100.html#d16741e4514a1635
From 7.4 onwards config guide does not talk about it all. I deleted the default SNMPv3 user & create a new user in 7.4 & add it to prime without rebooting WLC.
Once you configureed a SNMPv3 user on a WLC, I do no think you can edit/change the password. You have to delete the user & recreate it with modified username/password.Then re-add the WLC to prime
The behaviour you mentioned is with any of later codes of WLC ?
Rasika -
Prime Infrastructure 2.0 Collection Failure for WLC 5508
Hi,
We have installed prime infrastructure 2.0 as a VM.
I added 2 WLCs (AIR-CT5508) in the device work center.
Both the WLCs are showing as "Managed" but under the collection status it says "Collection Failure".
When I hover over the message it reads:
Other Error: Wireless Controller added successfully but some tables had their records dropped as their key fields failed validation"
Any ideas?
Thanks
SatyakiHi Satyaki,
Try to reboot the WLC ,if possible and then check the status of the issue.
Regards-
Afroz
**Ratings Encourages Contributors **** -
Cisco Prime Infrastructure 2.0 and ASA 55xx platform
Hello,
We recently upgraded to Prime Infrastructure 2.0 with the hope being able to manage our ASA's from PRIME (and complete an LMS migration).
When I attempt to add ASA's to prime i get the following collection errors:
Unable to collect processor and RAM information. Processor and RAM information. Unexpected error. See the log file inventory.log for details.
In the logfile I get the following XML parsing error on the MIB:
<palError>
<deviceId>6284310032</deviceId>
<code>VALIDATION_ERROR</code>
<message>Failed to validate output XML: cvc-maxInclusive-valid: Value '3484331296' is not facet-valid with respect to maxInclusive '2147483647' for type 'int'.</message>
<result>
<result xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="/CISCO-MEMORY-POOL-MIB/xmp-im-file-system-module.xsd">
<xmp-im-file-system-module>
<MemoryPoolStatistics>
<memoryPoolIndex>1</memoryPoolIndex>
<free>4294967295</free>
<largestFree>4294967295</largestFree>
<used>3484331296</used>
</MemoryPoolStatistics>
To me it seems that the ASA returns a value that is bigger then int32 and thus causes an overflow? Any clues? Workarounds to add an ASA to Prime without checking these MIB'S?
Regards,
MarcelThe X series (all with 64-bit SMP images) are not currently supported by PI 2.0. We can hope for a device update in the coming months to remedy that situation.
If you click on the arrow next to the help icon in the top right of your PI and choose "Device Level Support" you will see:
Cisco ASA-5500 Series Adaptive Security Appliances
Features :
Topology
LLDP Neighbor Discovery
CDP Neighbor Discovery
Configuration
Configuration Archive
Software Image Management
Monitoring
Device Availability
Reachability
Inventory
Physical
System - Memory Pools
Interfaces - IP
Interfaces - Ethernet
Device Type
SYSOIDS
S/W Version
Software
Cisco ASA-5510 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.669
OID:1.3.6.1.4.1.9.12.3.1.3.447
Cisco ASA-5510 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.773
Cisco ASA-5520 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.670
OID:1.3.6.1.4.1.9.12.3.1.3.448
Cisco ASA-5520 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.671
Cisco ASA-5540 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.672
OID:1.3.6.1.4.1.9.12.3.1.3.449
Cisco ASA-5540 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.673
Cisco ASA-5560 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.12.3.1.3.454
Cisco ASA-5550 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.753
Cisco ASA-5550 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.763
Cisco ASA-5505 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.745
OID:1.3.6.1.4.1.9.12.3.1.3.560
Cisco ASA-5580 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.914
Cisco ASA-5585 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.1194
OID:1.3.6.1.4.1.9.1.1195
OID:1.3.6.1.4.1.9.1.1196
OID:1.3.6.1.4.1.9.1.1197
Cisco ASA-5585 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.1198
OID:1.3.6.1.4.1.9.1.1199
OID:1.3.6.1.4.1.9.1.1200
OID:1.3.6.1.4.1.9.1.1201
Cisco ASA-5585 Adaptive Security Appliance System Context
OID:1.3.6.1.4.1.9.1.1202
OID:1.3.6.1.4.1.9.1.1203
OID:1.3.6.1.4.1.9.1.1204
OID:1.3.6.1.4.1.9.1.1205
Cisco ASA-5580 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.915
Cisco ASA-5580 Adaptive Security Appliance System Context
OID:1.3.6.1.4.1.9.1.916 -
Cisco Prime Infrastructure 2.0 and ASA 55xx platform problem
Hello,
We recently upgraded to Prime Infrastructure 2.0 with the hope being able to manage our ASA's from PRIME (and complete an LMS migration).
When I attempt to add ASA's to prime i get the following collection errors:
Unable to collect processor and RAM information. Processor and RAM information. Unexpected error. See the log file inventory.log for details.
In the logfile I get the following XML parsing error on the MIB:
<palError>
<deviceId>6284310032</deviceId>
<code>VALIDATION_ERROR</code>
<message>Failed to validate output XML: cvc-maxInclusive-valid: Value '3484331296' is not facet-valid with respect to maxInclusive '2147483647' for type 'int'.</message>
<result>
<result xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="/CISCO-MEMORY-POOL-MIB/xmp-im-file-system-module.xsd">
<xmp-im-file-system-module>
<MemoryPoolStatistics>
<memoryPoolIndex>1</memoryPoolIndex>
<free>4294967295</free>
<largestFree>4294967295</largestFree>
<used>3484331296</used>
</MemoryPoolStatistics>
To me it seems that the ASA returns a value that is bigger then int32 and thus causes an overflow? Any clues? Workarounds to add an ASA to Prime without checking these MIB'S?
Regards,
MarcelHi,
does anyone happen to know if that problem is fixed? My currently setup looks like this:
1. Cisco Prime Infrastructure 2.1 with updated device pack.
2. Assurance license
3. ASA5510 which has enabled netflow. Netflow is being sent to Cisco Prime 2.1
I do receive netflow raw data within Cisco Prime 2.1 but any graphical display of netflow data is not working. Does anybody has an idea where the problem is? Could it be that the graphical data is only displayed when sending netflow 1, netflow 5 or netflow 7?
regards
Maurus -
Prime Infrastructure 2.0 and Nexus 5548, SSH credentials fail
Hi,
I'm having problem getting the Prime Infrastructure 2.0 to login with SSH to a Nexus 5548 to do an inventory. I get "Wrong Telnet/SSH credentials". But when I use the same credentials from another SSH-client it works fine. I also tested to SSH from the console of the Prime-server and that also works fine.
Any ideas???
Regards,
Stefan LindkvistI have PI 2.0 working against Nexus 5k's in two different installations. See below for an example (click to enlarge).
Have you put in an entry in both the login and enable fields (even though they are not separately required when logging in directly)? -
Cisco Prime Infrastructure 2.0 and Cisco ASA
Hello,
We've recently installed trial version of Cisco Prime Infrastructure 2.0 Express. We hoped that it already supports Cisco ASA 55xx series (especially 5505, we have pretty amount of them). But we had some problems with PI and asa durind the exploitation process.
First, I've added ASA to PI, and Inventory Collection Status is Completed, but I can't see CPU and RAM utilization graphs. Inventory.logs are non-informative.
Also, config backup is success, but when I try to watch the backuped configuration at Configuration Archive PI says "Failed to fetch raw configuration". And so on.
ASA version is 5505, image is 9.1(2).
So, I have a question: is it possible to manage ASAs with PI 2.0?
UPD: I've just tried to upgrade asa to 9.1(4), and behavior of the equipment is quite the same. Seems we shall wait for 9.2 to be released.Have you downloaded and applied the latest Device Pack updates?
PI enhanced ASA support after the initial 2.0 release and the Device Packs incorporate that change.
The README file for Device Packs explains how to install them. (A bug currently does not allow the direct download in PI so you need to follow the method for installation from local storage after you manually download. Here is a link to the download location. -
Cisco Prime Infrastructure EoL/EoS and PSIRT reports
Hi
does PI 2.0 support these reports?
I have a trial version of 2.0, but can't seem to find these reports. In the release notes, it says these are supported?
New Features and Enhancements
•Support for End-of-Sale/End-of-Life Lifecycle Management reports for hardware, software and modules.
•Support for PSIRT reports detailing devices impacted by Cisco security advisories.
Any idea how to run these reports?
Thanks for your helpHi There,
I'm not sure if we are talking about the same thing, but we are running Prime Infrastructure 2.0. (2.0 (2.0.0.0.294))
You have to enable compliance from the settings (restart) and if you look under Report / Report Launch Pad, in the menu on the left is Device, click on there and you will see EOX ...... I've only had a quick look at the reports, but looks to work.
HTH
Simon -
Cisco Prime Infrastructure 2.0 and IPAM Solution
Hello everyone,
I'm student in a big company and my manager gave me a mission to study an IPAM solution.
In 3 month, we will use Cisco Prime Infrastructure 2.0
I turn to you cause I saw on this doc (link below) that CP Infrastructure 2.0 includes an IPAM Solution.
http://www.cisco.com/en/US/prod/collateral/netmgtsw/ps6491/ps11433/ps11480/ps11609/c45_658846_02_prime_aag.pdf
This IPAM Solution, is it just a repository to manage IP Adresse and DNS ?
Is it possible to write on DNS bind with IPAM of CP Infrastructure 2.0 ?
Thank you for your attention,
Cordially Vincent MaliquePas de problème Vincent.
The Network Registrar product is usually seen only in very large enterprises or service providers as it is designed to sale up to serving hundreds of thousands of addresses.
In smaller organizations looking to move beyond the spreadsheet method of keeping track of subnets, I have seen people have success with IPPlan (open source). Those wishing more functions and a supported product often go with SolarWinds IP Address Manager (IPAM) product. -
Prime Infrastructure 2.0 and User Tracking
Hello
I'm having a look at getting wired User Tracking working on Prime 2.0. I checked that it is supported in the following link:
http://www.cisco.com/en/US/prod/collateral/netmgtsw/ps6504/ps6528/ps12239/guide_c07-729089.html
I'm having a problem getting dynamic user tracking working for wired non-802.1x clients. The switches are configured for mac-notification traps and the config works fine for LMS.
Another LMS User Tracking feature I'd link to get working in Prime 2.0 is CUCM intergartion where Prime would pull IP Phone extensions/names etc from CUCM.
Are either of these User Tracking features supported in Prime 2.0 (or at least roadmapped) or should I stick with LMS 4?
Thanks
AndyI am gettng good non-802.1x wired user tracking info. see the screenshot below (click to expand).
I don't have a CM so I can't comment on that bit.
Row 1 in the screenshot, for example, is confirmed with the following CLI output:
User_Access#sh run int fa1/0/41
Building configuration...
Current configuration : 177 bytes
interface FastEthernet1/0/41
description user access
switchport access vlan 10
switchport mode access
snmp trap mac-notification change added
spanning-tree portfast
end
User_Access#sh mac address-table | i 1/0/41
10 000f.b58e.3732 DYNAMIC Fa1/0/41
User_Access#sh inv
NAME: "1", DESCR: "WS-C3750-48P"
PID: WS-C3750-48PS-S , VID: V10 , SN: FDO1425X2M9
User_Access#sh ver | i bin
System image file is "flash:/c3750-ipservicesk9-mz.122-55.SE5.bin"
User_Access# -
Prime Infrastructure 2.0 no 'Add a WLAN' option
Hello,
I've started to pay with PI 2.0 and I've noticed that there is no option to add new WLAN.
I am following manual:
Step 1 Choose Configure > Controllers.
Step 2 Click the IP address of the appropriate controller.
Step 3 From the left sidebar menu, choose WLANs > WLAN Configuration.
Step 4 From the Select a command drop-down list, choose Add a WLAN.
but there is no 'Add a WLAN' option. The only ones I've got there are:
Delete WLAN(s)
Schedule status
Mobility Anchors
Foreign Controller Mappings
Does anyone know how to get that option there?
Thanks
TomaszHi,
you're right that this can only be done with the template but to create one I needed to go to:
Design --> Feature Design
and then under Templates:
Features and Technologies --> Controller --> WLANs --> WLAN Configuration
There I've created new template for WLAN and then deployed it to controllers.
Maybe that's better way to do it, when you have many controllers.
Thanks
Tomasz -
Prime Infrastructure API add device
I've been looking at the Prime Infrastructure 2.1 API at /webacs/api/v1/ on my PI instance but I can't seem to find a way to add devices using the API? Looking to write a script for our techs to run after the provisioning of a new device and would love a way to get it added to Prime. Any ideas?
It isn't possible in Prime Infrastructure 2.1 to add devices via API, however, it now is possible with version 2.2. I've used it myself and I can confirm that it works.
Maybe you are looking for
-
Os x 10.8.3 freezes when changing screen saver
I recently installed 10.8.3. One of the glitches is that when I attempt to change the screen saver, my computer freezes. Is there a fix for this?
-
1099 Report for OTV - Classic Withholding Tax
Hello Members, We run on SAP ERP 6.0 EHP6 and use the classic withholding tax functionality. Wondering what the rest of the world with classic setup is using for 1099-MISC reporting for one time vendors ? Currently we follow a cumbersome process of p
-
Shopping cart in iweb NO PAYPAL
I would like to insert a shopping cart WITHOUT using paypal. I know how to create the "add to shopping cart" buttons, but can not figure out how to get them to link to an actual shopping cart page that should total everything up. I will be authorizin
-
Hi All...I need some help....I am new to the 8100. I am trying to load an OS but my blackberry won't stay connected long enough. It keeps connecting and unconnecting while I am trying to load. When it is off....I just get the LCD light going on and o
-
I noticed that there isn't yet a thread in order to report E55 firmware bugs, so I started this Here the firmware bugs I've found: - Hidden WLAN: when you search for wireless access points (for example from the main screen) the phone see always one "