Prime infrastructure 2.0 inventory reports

In lms it was easy to get inventory report on our router cards draughtboards etc. when I go to report launch pad>device>detailed hardware and run combined inventory I get "no data found" under the modules and interfaces....this is the ONLY report requested by the customer, is this really not available in PI 2.0?
Sent from Cisco Technical Support iPad App

Reports (deatiled Hardware ) are working fine for me. check the attached screenshot
Check the device "Inventory collection status " under device >workcenter . status should be completed for those device
Thanks-
Afroz
[Do rate the useful post]

Similar Messages

Prime Infrastructure 2.0: Inventory/detailed HW reports customizing

Hello,
isn't it possible to run a/one detailed hardware report that includes the chassis information Name, the device name, the chassis serial number?
Example:
Chassis Information Name
Device Hostname
Serial Number
WS-C3750V2-24PS-S
switch1x2
FX31338243d
In my knowledge I have to run a "Wired Detailed Device Inventory" report to get the chassis informatin name and a "Detailed Hardware" report to get the device hostname.
In LMS it was possible to customize the inventory reports. It looks like the Prime 2.0 is not that flexible in customizing the reports or has anyone a tip for me?
Thanks
Bastian

Sorry, but as far as I know this can't be done with PI 2.0 like it could be on LMS 4.x.
I agree it would be a very useful feature. Add to the reporting the ability to get all members of a switch stack and we would have a winner.

Cisco prime infrastructure 2.0 inventory SFP

hello,
anyone knows if it is possible with cisco prime infrastructure 2.0 create inventory to obtain data from SFP (serial number and model)?
thank you

Hi ,
Can you try the below report and see if you are able to see the information , you are looking for
Report > Report Launch Pad > Device > Detailed Hardware
Thanks-
Afroz
***Ratings Encourages Contributors ****

Cisco Prime Infrastructure 2.1 Inventory Job

My cisco prime infrastructure performs a switch inventory job every night at 22:00 hrs. When I looked at the syslog of the devices in the inventory, I see some entries that I never saw with other LMS versions.
2014-06-30 22:00:01   Local7.Notice   xxx.xxx.xxx.xxx   5410: Jun 30 22:00:00.623 CST: %SYS-5-CONFIG_I: Configured from xxx.xxx.xxx.xxx by snmp
2014-06-30 22:00:01   Local7.Notice   xxx.xxx.xxx.xxx   5411: Jun 30 22:00:01.567 CST: %SYS-5-CONFIG_I: Configured from console by vty1 (xxx.xxx.xxx.xxx)
2014-06-30 22:05:10   Local7.Notice   xxx.xxx.xxx.xxx   5412: Jun 30 22:05:09.008 CST: %SYS-5-CONFIG_I: Configured from console by vty0 (xxx.xxx.xxx.xxx)
I don't understand what the PI is doing with the switches. Does anyone know what is happening during this inventory background job? TIA

Hello all,
we have the same problem maybe; Cisco Prime IF 2.1 is changing the running-configs and produces out-of-syncs ;
it turns so for us is, as if Cisco Prime IF 2.1 a snmp-server host x.x.x.x community entry writes in the running-config,
so are running-and startup-config are out-of-sync; is this correct? Herbert

Cisco Prime Infrastructure - Is there a report of unused switch ports?

Hello,
Is there a report in Cisco Prime Infrastructure 1.4 showing the unused switch ports?
There used to be one in Cisco Prime LMS (Reclaim Unused Up/Down Ports Report).
Thank you,
Luke

Hello,
I now have Cisco Prime Infrastructure 2.0 running, and I don't see a report like the "Reclaim Unused Up/Down Ports" report that existed in LMS.
I found one called "Interface Capacity", but it only shows the number of ports that are "connected", "notconnect" or "disabled".
Does anyone know if a report of Unused ports exists in Prime Infrastructure 2.0 or if it will be available later on?
Thank you,
Luke

Cisco Prime Infrastructure 2.1 Custom Reports

Hi, I need to generate a custom Guest User report from Cisco Prime Infrastructure 2.1. It needs to have a couple more fields added to the existing "Guest User Association" report.
Is it possible to connect to the Cisco Prime Infrastructure Database and Generate custom reports? Is there any documentation on this?
Thanks

Programmatic access to PI's data is via the REST API.
Check the help menu on your PI server to see documentation regarding the supported tables and fields that can be queried via that method.

Prime Infrastructure Failed to run report

Hi all,
on a new installed PI 1.2.1 I have the following error message as soon as I run a report:
Failed to run report: Could not connect to HTTP invoker remote service at [http://localhost:20556/reportingserver/remoting/ReportingService-httpinvoker]; nested exception is java.net.ConnectException: Connection refused
I'm not sure if the "localhost" is the problem.
Anybody any idea?

Stopping and starting NCS didn't seem to help me. Reporting was running before I stopped NCS and after starting NCS
Any other ideas?
server/admin# show version
Cisco Application Deployment Engine OS Release: 2.0
ADE-OS Build Version: 2.0.1.038
ADE-OS System Architecture: x86_64
Copyright (c) 2005-2010 by Cisco Systems, Inc.
All rights reserved.
Hostname: SV195968
Version information of installed applications
Cisco Prime Network Control System
Version : 1.2.1.012
server/admin#
Failed to run report: Could not connect to HTTP invoker remote service at [http://localhost:20556/reportingserver/remoting/ReportingService-httpinvoker]; nested exception is java.net.ConnectException: Connection refused
server/admin# ncs status
Health Monitor is stopped.
Reporting Server is Stopped
Ftp Server is Stopped
Database server is stopped
Tftp Server is Stopped
Matlab Server is Stopped
NMS Server is stopped.
SAM Daemon is not running ...
DA Daemon is not running ...
Syslog Daemon is not running ...
status
server/admin# ncs start
Starting Network Control System...
This may take a few minutes...
Network Control System started successfully.
start
server/admin#
server/admin#
server/admin# ncs status
Health Monitor Server is running.
Reporting Server is running
Ftp Server is Disabled
Database server is running
Tftp Server is Disabled
Matlab Server is running
NMS Server is running.
SAM Daemon is running ...
DA Daemon is running ...
Syslog Daemon is running ...
status
server/admin#

Prime infrastructure 2.0 - Inventory error with Virtual-Access Interface

Hi,
We have recently been trying to resolve a few issues with routers which get partial inventory failures upon discovery. I have managed to narrow this down slightly with the help of the inventory.log file. (With help from this post https://supportforums.cisco.com/thread/2255346 ) I have found the following happnes when this device is added:
[2014-03-04 14:00:27,537] [ICE Service[ 1]Thread: 29] [inventory] [ERROR] - 172.16.3.202 Object detected as SAME but DB Object obtained from the database is NULL For instance id: 0 For generated POJO: PPPEncapsulation[callBack=false,callIn=false,callOut=false,multilink=false,name=Virtual-Access1,oneTime=false,owningEntityId=69757688_172.16.3.202,preferedAuthType=NONE,deployPending=NONE,name=Virtual-Access1,owningEntityId=69757688_172.16.3.202,instanceId=0,_orderedListOEIndex=<Integer>,_creationOrderIndex=<Integer>,instanceVersion=0]
I have highlighted above where it mentions the problem with the virtual access interface. The configuration on the router is for PPPoE and the virtual-access1 interface is bound to Dialer0.
It then goes on to roll back the transaction:
172.16.3.202 persistObjects called with addList size = 307, updateList size = 6
172.16.3.202 Exception while persisting: com.cisco.xmp.persistence.common.util.DMMCRUDException:,message=errorId=12,componentName=CRUD Error Create Object Failed
172.16.3.202 Exception occured while inventory collection for device with id 69757688: com.cisco.xmp.inventory.ice.InventoryException: errorId=12,componentName=CRUD Error Create Object Failed
172.16.3.202 Done with collection. Total call method time: 15308
172.16.3.202 Rolling back the transaction
Has anyone else come accross this issue?
I have attched the log showing just messages from this device.
Thanks,
Mike.

TAC and I found a bug, CSCum05301.
May be that is also helpfull for others.
https://tools.cisco.com/bugsearch/bug/CSCum05301/
Symptom:
Inventory collection will fail if following keywords are used as part on description command on the interface config level of IOS device: 1Gbps, 10Mbps etc.
Following error message is visible on the DWC:
Inventory Collection Status: Partial Collection Failure
Collection Status Failed feature(s)
Unable to configure DSL, Serial, POS, Ethernet, Loopback, Virtual-Interface, Tunnel, Vlan, Switchport and Service Module interfaces on ISR, ASR and Switches.
Conditions:
Speed keywords like 1Gbps, 10Mbps etc. available as part of descrption command in IOS interface level.
For example:
interface FastEthernet0/3
description 10Mbps
Workaround:
Use a space character between number and unit keyword, like 1 Gbps.

Prime Infrastructure 2.0: Inventory Collection - Partial Collection Failure on 2 of 4 VSS WS-C6509-E

Hello,
I've got a strange behaviour regarding the inventory collection for 2 of 4 virtual switching systems.
That means the inventory collection for two VSS is succesfull (inventory collections status = Completed) for the other two systems it is not, see attachments.
The device credentials like SNMP-RW, SSH acces are OK. I've already tried to increase SNMP timout and retries as well as telnet/ssh timout without success
All 4 systems are identical regarding hardware model and software vesion.
HW: WS-C6509-E
SW: 12.2(33)SXJ3
Any ideas or suggestions?
Best regards,
Bastian

TAC and I found a bug, CSCum05301.
May be that is also helpfull for others.
https://tools.cisco.com/bugsearch/bug/CSCum05301/
Symptom:
Inventory collection will fail if following keywords are used as part on description command on the interface config level of IOS device: 1Gbps, 10Mbps etc.
Following error message is visible on the DWC:
Inventory Collection Status: Partial Collection Failure
Collection Status Failed feature(s)
Unable to configure DSL, Serial, POS, Ethernet, Loopback, Virtual-Interface, Tunnel, Vlan, Switchport and Service Module interfaces on ISR, ASR and Switches.
Conditions:
Speed keywords like 1Gbps, 10Mbps etc. available as part of descrption command in IOS interface level.
For example:
interface FastEthernet0/3
description 10Mbps
Workaround:
Use a space character between number and unit keyword, like 1 Gbps.

Prime Infrastructure (2.0) utilization report on port group possible?

Hello
I want to create an interface utilization report for a specific port group in PI, but can't see how to do that in the report setting. You only seem to be able to select a specific device or site rather than port group. Is it possible? Also, is it possible to put that on a dashlet?
thanks for your help

Thanks for that Mahavir
Yes, I worked that out a little while ago, and can now see interface utilization by port group on the Performance > Network Interface page. I do have another question however (well two)....
I wanted to add graph over time for the utilization to the detail dashboard, but nothing shows up, even though I see the utilization in the network interface page, so I'm sure the monitoring is deployed. Why is the data missing from the graphs?
Also, I wanted to see interface packets per second graphs, but see that is not part of any default template, so I created a customer SNMP template from the IF-MIB to do this, but I can only deploy that against sites/devices or a list of interfaces, and not port groups. Why can't I deploy a customer SNMP template against a port group?
thanks for your help

Prime Infrastructure (V2.1) CleanAir reports- historical data

Is there a configurable item for the data retention of clean air lowest AQ over time?
If I run a report and choose the option for "last 4 Weeks" I only get the last five days
In fact in the Clean air dashboard if I choose the last one hour I still see the last five days.

It looks like NCS 1.3 allows you to update the OUI via - Admin->system settings -> user defined OUI
If you are on NCS 1.1.1.24, you will need to upgrade to 1.3 to modify the OUI

Cisco Prime Infrastructure 1.3 - Assurance reporting

We have Assurance license and we are exporting netflow and pretty much everything is working fine. Traffic is seen, recognized by protocol, DSCP, source/destination IPs, etc.
Now, the question is, can dashlet present data that is less than one hour?
For example, you select Serial interface on MPLS router and it will show you IP addresses that used most amount of bandwidth in last hour, but it would be much better if we could chose much less amount of time (like 5 minutes or lower), because in case of temporary congestion it won’t give exact information who is using most of the traffic. We would like to see who is currently consuming most of the bandwitdth.
Or is there any other way to get info for interface level (or device) who’s using most and what type of traffic (something similar to show ip cache flow command on the router).

Under the "Detailed Dashboards" pages, you can customise the Time Frame in there. Default is past hour but you can specify smaller and/or more specific time periods as necessary... I've checked that this works ok in CPI 1.3 for both the "Interface" and the "End User Experience" tabs.
Richard

Prime Infrastructure 2.2- problems: Wired Detailed Device Inventory report not running / Cisco 5500 WLCs no listed in subgroup

New installation of Prime Infrastructure 2.2.0 (PI-VA-2.2.0.0.158.ova)
installed fixes/software/device packs:
PI 2.2.1 Poodle Fix (installed)
PI 2.2.1 Maintenance Release (installed,ncs stopped,rebooted)
Prime Infrastrucutre 2.2 Device Pack 3 (installed,ncs stopped,rebooted)
Licences installed (ncs stopped,rebooted)
Added all devices via Bulk Import (Inventory>Device Management>Network Devices)
Problem 1:
The Cisco 5500 WLCs are not listed in Inventory>Device Management>Network Devices (see screen shot) but listed under "All Devices"!
The Cisco 4400 WLCs and the 8500 WLCs are listed within their subgroup.
Devices are in "Managed State"
Problem 2: fixed! (Browser issue)
Problem 3:
Unable to run "Wired Detailed Device Inventory" report because I get the error message: Failed to run report: Unable to retrieve data for: Chassis Information (if Chassis Information is selected, if System Information is selected I get the error message with ...retrieve data for:System Information)
All devices do have an "Admin Status = Managed" and the Last Inventory Collections Status = Completed.
Has anyone the same issues or a tip for me?
Another topic, the "User Defined Fileds" are not exported when with running a "Device Export" (Inventory > Device Management > Network Devices). ;-(
BR
Bastian

Hallo Bastian,
I think you still have browser issue, Using IE is still the best with Prime.
I have exactly same prime 2.2 and installed fixes/software/device packs.
I have no problem I can see all views. I use now IE 11, with Chrome 42.0.2311.90 and firefox 37.01 I have problems too with lots of views. You have not tell what browser + version you have.
Since you have same prime 2.2 as me. I have other problems, can you check yours?
Can you see a functional CLI template page at Configuration > Templates > Features & Technologies:
https://supportforums.cisco.com/discussion/12481691/can-cisco-prime-22-still-do-simple-ad-hoc-deployment-job-cli-over-all-switches
Do you have SNMP Connectivity Failed while Verify Credentials has no errors all green and checked.
https://supportforums.cisco.com/discussion/12494786/snmp-request-exceeds-internal-data-buffer-512-bytes-prime-22-asa-5545

Prime Infrastructure 2.1: Report - Device - Inventory

Hi there,
we want to have an inventory report of your device database.
The infrastructure is a wild mix of Catalyst 6500er, 3560X, 3750X, N7K, N5K, WLC, etc.
We are using the prime infrastructure 2.1 Report Launch Pad and the API site. The maximum we get of a N7K:
UDI serial number
FAN serial number
The whole Module serials numbers are missing. How do we get this data?
br,
chris

Hi,
here is an update:
There are more than one Report you need to start to get data for Device, FAN, Power Supply, Module - look at these reports:
Report > Report Launch Pad > Device > Inventory
Report > Report Lauch Pad > Device > Wired Detailed Device Inventory
Report > Report Lauch Pad > Device > Wired Module Detail > Wired Module Detail Report Details
SFPs and GBICs cannot be reported til now - there are working on it.
br,
chris

Prime Infrastructure 2.1 Client Statistic Report Issues

Hello Community,
I hope you can help with a couple of issues I am seeing on Prime Infrastructure 2.1, running an evaluation 60 day license.
My PI 2.1 build is currently managing a WLC 5508 running 7.4.121.0, which has been added successfully. No configuration changes were applied to the WLCs, other than SNMP community. No AVC or medianet configuration is applied.
When looking in the 'Operate>Client and Users' dashboard; I can see connected clients and if I select one of them, I can see further details like session, security and client statistics (showing traffic and 802.11 metrics). These are the table views that show current values, however, further down I see graphs but they do not contain any information for RSSI, SNR or traffic sent & received (packets or bytes).
Question: Should I see this information under an evaluation license and if so, what could be stopping it?
Also, when I run the reports 'Report>Report Launch Pad' and select 'Client>Client Traffic' or 'Client>Client Throughput' the resulting report contains 0 bps, when I select 'Report By' AP by Floor Area. I have created a single floor area and placed three access points into it.
Out of interest if I do a report of the same type using 'Report By' All or AP by Controller, I do see traffic graphs for 3 out of 333 access points. Just not the access points that are in my floor area. Also the amount of traffic utilization is tiny (less than a kbps) for a WLC with 800 users.
For a 'Client>Client Count' report using AP by Floor Area, I do see the client numbers connected to the WLC/APs in my configured floor area.
Question: Should I see reports for client traffic and throughput under an evaluation license for floor areas and if so, what could be stopping it?
I have checked the background task and the 'Client Statistics' task is enabled and run time is being updated.
Kind regards,
Ian

Hi,
here is an update:
There are more than one Report you need to start to get data for Device, FAN, Power Supply, Module - look at these reports:
Report > Report Launch Pad > Device > Inventory
Report > Report Lauch Pad > Device > Wired Detailed Device Inventory
Report > Report Lauch Pad > Device > Wired Module Detail > Wired Module Detail Report Details
SFPs and GBICs cannot be reported til now - there are working on it.
br,
chris

Prime infrastructure 2.0 inventory reports

Similar Messages

Maybe you are looking for