Prime Infrastructure 2.0 Job Approval notifications?
I have a question about notification for job approvers in Prime 2.0. I'm trying to setup PI such that a restricted user can create a configuration change on a wireless controller and submit it for approval by the PI admin.
The PI admin will likely not be logging in every day to check job approval status. I can't see anywhere that notifies the admin via email that a job is waiting. can this be done or am I missing something?
-Tim
Hi Tim,
I don't think we have an email optiom to notify the ADMIN to approve the pending jobs ,however if you authorized any job then ONLY admin can approve to run the job.
check the below link:
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/administrator/guide/config_server_settings.html#wp1081686
Thanks-
Afroz
[Do rate the useful post]
Similar Messages
-
We're upgrading from LMS 3.2 to Cisco Prime Infrastructure ...
In LMS 3.2 we're using netconfig all the time to configure various jobs related to port security
In installing Cisco Prime Infrastructure and working through it's use of templates, I'm having some difficulty finding out how to send out a notification once a configuration job has completed. It's so simple in LMS 3.2 since it's part of the job creation screens.
Any assistance would be greatly appreciated.HI, Raymond
Just wondering if this problem is resolved?
Thanks! -
Email Notifications on Prime Infrastructure 2.1
Hi Everyone,
I have a Cisco Prime Infrastructure 2.1 with almost 100 switches registered and managed properly. I have configured the Mail Server and alarm notifications are sent with no problems.
The deal is that I don´t want to recieve alarm mails for every single device that is registered. Is it possible to recieve mails just for a group of devices? I was checking the Cisco documents but could not find something clear about this.
Thanks for your help,
RicardoHi Everyone,
I have a Cisco Prime Infrastructure 2.1 with almost 100 switches registered and managed properly. I have configured the Mail Server and alarm notifications are sent with no problems.
The deal is that I don´t want to recieve alarm mails for every single device that is registered. Is it possible to recieve mails just for a group of devices? I was checking the Cisco documents but could not find something clear about this.
Thanks for your help,
Ricardo -
A job in Cisco Prime Infrastructure 2.1 has been running for 50 days
I found a job (SAM_Poller_22_15_GETVPNPoller_1878262177) in cisco prime infrastructure 2.1 (Administration -> Job Dashboard -> System-defined), which has been running for about 50 days. Is this normal? How can I stop it? Thanks for any help..
SAM_Poller_22_15_GETVPNPoller_1878262177
PollerJob
In-Progress
Running
2014-09-19 01:28
49 Days 01 : 28 : 37Not normal, seems to be stuck. Try to stop (ncs stop) and start (ncs start) the system processes, which should stop this job.
If it happens again, i would recommend to open a TAC case for further investigation.
-Thanks
Vinod -
Cisco Prime Infrastructure 2.1 Inventory Job
My cisco prime infrastructure performs a switch inventory job every night at 22:00 hrs. When I looked at the syslog of the devices in the inventory, I see some entries that I never saw with other LMS versions.
2014-06-30 22:00:01 Local7.Notice xxx.xxx.xxx.xxx 5410: Jun 30 22:00:00.623 CST: %SYS-5-CONFIG_I: Configured from xxx.xxx.xxx.xxx by snmp
2014-06-30 22:00:01 Local7.Notice xxx.xxx.xxx.xxx 5411: Jun 30 22:00:01.567 CST: %SYS-5-CONFIG_I: Configured from console by vty1 (xxx.xxx.xxx.xxx)
2014-06-30 22:05:10 Local7.Notice xxx.xxx.xxx.xxx 5412: Jun 30 22:05:09.008 CST: %SYS-5-CONFIG_I: Configured from console by vty0 (xxx.xxx.xxx.xxx)
I don't understand what the PI is doing with the switches. Does anyone know what is happening during this inventory background job? TIAHello all,
we have the same problem maybe; Cisco Prime IF 2.1 is changing the running-configs and produces out-of-syncs ;
it turns so for us is, as if Cisco Prime IF 2.1 a snmp-server host x.x.x.x community entry writes in the running-config,
so are running-and startup-config are out-of-sync; is this correct? Herbert -
Can't import images in cisco prime infrastructure 1.2
- Any job , trying to import images, in my cisco prime infrastructure fails with :
Jan 14 13:14:53 cisco-prime 01/14/13 13:15:18.040 ERROR [service] [pool-4-thread-19] IFM_SWIM_EXCEPTION: [com.cisco.ifm.swim.service.exception.IfmSwimParserException: Cannot populate software image info object from the image.]
How I can I solve this one ?
Tx,
M.I seem to have the same problem, strangely enough importing a universal image for 2960s worked fine, but I get thos error when trying to import a 3750x image
-
Cisco prime Infrastructure alarms by e-mail
hi all,
my Cisco PI1.2 not send me a notification e-mail with specific alarm if occurred twice and the first time is not cleared or deleted.
i.e.
if a switch is down it send me a notification e-mail, and this switch comes up again but i did not remove the first alarm, the PI not send me a notification.
please advice
thanks in advanceAlarm Status
Description
New
When an event triggers a new alarm or an event is associated with an existing alarm.
Acknowledged
When you acknowledge an alarm, the status changes from New to Acknowledged.
Cleared
An alarm can be in these statuses:
Auto-clear from the device—The fault is resolved on the device and an event is triggered for the same. For example, a device-reachable event clears the device-unreachable event. This in-turn, clears the device-unreachable alarm.
Manual-clear from Prime Infrastructure users: You can manually clear an active alarm without resolving the fault in the network. A clearing event is triggered and this event clears the alarm.
If the fault continues to exist in the network, a new event and alarm are created subsequently based on the event notification (traps/syslogs).
This might be the reason, I believe.
Please refer the following link for better understanding.
http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/1-2/user/guide/prime_infra_ug/alarms.html
Hope that helps. -
Prime Infrastructure 2.0 disk requirements
The installation guide for Prime 2.0 says it requires 200 MB/s of disk throughput. Does this mean 200 MB/s sustained IO?
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/quickstart/guide/cpi_qsg.html#wp69178Hi Graham,
What settings do you have checked when you navigate to here?
Operate > Alarms & Events > Email Notification
Also you can define within your network what the level of alarming should be through navigation to here:
Administration > System Settings > Severity Configuration
It doesn't take much to become overburdened by alarms from Prime, I set only a couple of parameters as critical for switch and router state, and set to receive emails from those at this time.
Regards,
Brandon -
Hello,
we're running Prime Infrastructure 2.0 (version VA-2.0.0.0.294).
I was scared as I figured out one hour ago that running an inventory sync (Device Work Center) removes the command snmp-server location and adds the command snmp-server host "PI-ip address" "snmp rw community" in the running-config.
Has someone the same behaviour or can reenact this scenario?!
Can someone imagine that this behaviour has something to do with a configuration setting in PI?
I'm perplexed and got gray hair now.
Thank you for your answers or tips.
BastianHello Rob,
I just successfully installed the patch. The snmp-server location is not touched anymore while running a inventory job.
But PI still enters this string in the running-configuration:
snmp-server host "PI-IP address" " our snmp RW community- string"
although there already exists the entry:
snmp-server host "PI-IP address" version 2c "community-string (not the snmp rw-community-string)"
Do you or anyone else has the same behaviour that PI adds automaically himself as snmp trap receiver with the SNMP-RW community?
Regards
Bastian -
Cisco Prime Infrastructure 2.0 - no traps/info are pushed from devices
Good evening,
I have setup Cisco Prime Infrastructure 2.0 and, though I have added manually my 4 network cores as devices without any problem, I can't get a single trap or a single SNMP information to be pushed into my Cisco Prime Infra.
Here is my SNMP config on my core :
snmp-server user *edited* *edited* v3
snmp-server group *edited* v3 noauth notify *tv.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF0F
snmp-server community *edited* RO
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps flowmon
snmp-server enable traps transceiver all
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps rf
snmp-server enable traps memory
snmp-server enable traps cpu_threshold
snmp-server enable traps eigrp
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change nssa-trans-change
snmp-server enable traps ospf cisco-specific state-change shamlink interface
snmp-server enable traps ospf cisco-specific state-change shamlink neighbor
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps flex-links status
snmp-server enable traps fru-ctrl
snmp-server enable traps entity
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps ether-oam
snmp-server enable traps aaa_server
snmp-server enable traps flash insertion removal
snmp-server enable traps l2tc threshold sys-threshold
snmp-server enable traps power-ethernet police
snmp-server enable traps rep
snmp-server enable traps vswitch dual-active vsl
snmp-server enable traps udld link-fail-rpt status-change
snmp-server enable traps vtp
snmp-server enable traps vlancreate
snmp-server enable traps vlandelete
snmp-server enable traps auth-framework sec-violation
snmp-server enable traps dot1x auth-fail-vlan guest-vlan no-auth-fail-vlan no-guest-vlan
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps entity-diag boot-up-fail hm-test-recover hm-thresh-reached scheduled-test-fail
snmp-server enable traps port-security
snmp-server enable traps ethernet evc status create delete
snmp-server enable traps energywise
snmp-server enable traps ipsla
snmp-server enable traps vstack
snmp-server enable traps bfd
snmp-server enable traps bgp
snmp-server enable traps bulkstat collection transfer
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps ipmulticast
snmp-server enable traps isis
snmp-server enable traps msdp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
snmp-server enable traps syslog
snmp-server enable traps isakmp policy add
snmp-server enable traps isakmp policy delete
snmp-server enable traps isakmp tunnel start
snmp-server enable traps isakmp tunnel stop
snmp-server enable traps ipsec cryptomap add
snmp-server enable traps ipsec cryptomap delete
snmp-server enable traps ipsec cryptomap attach
snmp-server enable traps ipsec cryptomap detach
snmp-server enable traps ipsec tunnel start
snmp-server enable traps ipsec tunnel stop
snmp-server enable traps ipsec too-many-sas
snmp-server enable traps errdisable
snmp-server enable traps ethernet cfm alarm
snmp-server enable traps vlan-membership
snmp-server enable traps mac-notification change move threshold
snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down
snmp-server host *ip-address-edited* version 3 noauth *edited*
Basically all traps are enabled but absolutely nothing is showing up in my Prime Infra except that my 4 devices are "Reachable".
Here is a show snmp on the same device :
sh snmp
Chassis: *S/N Edited*
38554534 SNMP packets input
0 Bad SNMP version errors
14 Unknown community name
0 Illegal operation for community name supplied
0 Encoding errors
38453185 Number of requested variables
0 Number of altered variables
17790703 Get-request PDUs
20583581 Get-next PDUs
0 Set-request PDUs
0 Input queue packet drops (Maximum queue size 1000)
38490708 SNMP packets output
0 Too big errors (Maximum packet size 1500)
0 No such name errors
0 Bad values errors
0 General errors
38371069 Response PDUs
13 Trap PDUs
SNMP global trap: enabled
SNMP agent enabled
SNMP logging: enabled
Logging to *edited*, 0/10, 13 sent, 0 dropped.
Can anyone point out what is wrong or missing in my configuration? I can't seem to single it out myself.
Thanks
JeremyHi Jeremy,
SNMP traps are shown in the events and alerts section of PI.
SNMP config looks fine. Can you run the SNMP debug (debug snmp packets ) .check the logs and see if the device is actually sending the TRAPS to the PI server.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors **** -
New installation of Prime Infrastructure 2.2.0 (PI-VA-2.2.0.0.158.ova)
installed fixes/software/device packs:
PI 2.2.1 Poodle Fix (installed)
PI 2.2.1 Maintenance Release (installed,ncs stopped,rebooted)
Prime Infrastrucutre 2.2 Device Pack 3 (installed,ncs stopped,rebooted)
Licences installed (ncs stopped,rebooted)
Added all devices via Bulk Import (Inventory>Device Management>Network Devices)
Problem 1:
The Cisco 5500 WLCs are not listed in Inventory>Device Management>Network Devices (see screen shot) but listed under "All Devices"!
The Cisco 4400 WLCs and the 8500 WLCs are listed within their subgroup.
Devices are in "Managed State"
Problem 2: fixed! (Browser issue)
Problem 3:
Unable to run "Wired Detailed Device Inventory" report because I get the error message: Failed to run report: Unable to retrieve data for: Chassis Information (if Chassis Information is selected, if System Information is selected I get the error message with ...retrieve data for:System Information)
All devices do have an "Admin Status = Managed" and the Last Inventory Collections Status = Completed.
Has anyone the same issues or a tip for me?
Another topic, the "User Defined Fileds" are not exported when with running a "Device Export" (Inventory > Device Management > Network Devices). ;-(
BR
BastianHallo Bastian,
I think you still have browser issue, Using IE is still the best with Prime.
I have exactly same prime 2.2 and installed fixes/software/device packs.
I have no problem I can see all views. I use now IE 11, with Chrome 42.0.2311.90 and firefox 37.01 I have problems too with lots of views. You have not tell what browser + version you have.
Since you have same prime 2.2 as me. I have other problems, can you check yours?
Can you see a functional CLI template page at Configuration > Templates > Features & Technologies:
https://supportforums.cisco.com/discussion/12481691/can-cisco-prime-22-still-do-simple-ad-hoc-deployment-job-cli-over-all-switches
Do you have SNMP Connectivity Failed while Verify Credentials has no errors all green and checked.
https://supportforums.cisco.com/discussion/12494786/snmp-request-exceeds-internal-data-buffer-512-bytes-prime-22-asa-5545 -
Prime Infrastructure 2.0 does not show Planning Mode
Hi,
I´d like to know if evaluation version of Cisco Prime Infrastructure 2.0 (PRIME-NCS-VAPL) does not provide the feature "Planning Mode" to conduct a Predictive Site Survey.
Monitor>Site Maps>Select an Site>
At the drop down list (select a command), I can´t see planning mode. The options are: New Building, New Outdoor Area, Edit Campus/Site, Delete Campus/Site, Configure Interferer Notifications.
I also notice that "Add Access Points" does not appear.
see the att image.
Tks.Hi ,
1. Monitor > Site Maps
2. Select the appropriate location link from the list that appears.
A color-coded map appears showing placement of all installed elements (access points, clients, tags) and their relative signal strength.
CLICK on the " color-coded map "
Now on the right hand side Drop Down Menu , you should be able to see the "Planning Mode"
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors **** -
Prime Infrastructure 2.1 Compliance Licensing
Till Date LMS and Cisco Prime Infrastructure are standalone applications and do not operate in sync.
If you deploy a new application server for LMS, it will be working separately and you can have its compliance manager running with this license applied.
Don't expect integration. Even though PI is eventually destined to be the primary NMS application from cisco and LMS to suppose be phased out, still CPI hasn't reached the feature parity as per LMS, so we still offer our customer's option to run LMS for those features they don't find in CPI.
So as per your question :
So does this mean, if I have purchased the compliance licenses, I have to deploy LMS 4.2 to utilize these licenses?
The Answer is unfortunately yes.
-Thanks
VinodYes, ideally you should have received multiple PAK or license files, like base license for PI and add-on device license etc. Any one of them having **LMS** in the PAK/Licence file name refers to a LMS license.
You should check more details with the vendor or your cisco's account manager.
LMS has various modules embedded in itself like configuration archive, performance, monitoring, inventory management, compliance manager etc.
It has central device repository from where all these modules get device and credential information. You'll have to configure various compliance jobs/templates etc with one or group of devices to run once or periodically.
Compliance DB stays in sync with LMS and from there you can use it. If you are planning to use Compliance, you can install LMS and use compliance under 60 days evaluation period.
For more details check the document :
Using Compliance and Audit Manager Feature
-Thanks
Vinod
**Encourage Contributors. RATE Them.** -
WCS and LMS to Cisco Prime Infrastructure 1.3 Upgrade
Hello,
Our customer is currently having WCS for 500 devices and LMS 3.2 for 1500 devices. We are planning to upgrade to Cisco Prime Infrastructure 1.3.
I want to check is the upgrade procedure that we have planned is ok or we have missed something.
Phase 1: WCS to CPI 1.3 upgrade
1. Check that WCS is at 7.0.230.0 version
2. Export WCS database
3. Install NCS 1.1.1.24 software
4. Contact cisco to obtain trial license for NCS software (L-WCS-NCS1-M-K9 license).
5. Migrate WCS license and import it in NCS software
6. Migrate WCS data to NCS software using ncs migrate command
7. Patch NCS software
8. Inline upgrade to CPI 1.3 software
9. Install proper licenses on CPI 1.3 (WCS and LMS device count)
My concern in this first phase is should I use NCS large image since our Cisco Prime Infrastructure 1.3 software should manage 2000 devices at the end.
Or is it better not to perform inline upgrade and insted go with exporting data from NCS and then importing them to CPI 1.3 that is going to be installed separately?
Phase 2: LMS 3.2 to CPI upgrade
1. Export LMS 3.2 database
2. Install LMS 4.2 software
3. Install license to LMS 4.2
4. Restore data from LMS 3.2 to LMS 4.2
5. Direct upgrade from LMS 4.2 to 4.2.2
6. Export the device list with credentials from LMS 4.2.2 and import it as a Bulk Import in CPI 1.3
At the end we will have CPI 1.3 and LMS 4.2.2 software running.
Is it possible to directly upgrade from LMS 4.2 to LMS 4.2.4 and then import data to CPI 1.3 or we need to go with 4.2.2 version?
Regards,
JelenaHello Marvin,
We have restored LMS 3.2 SP 1 database on LMs 4.2 and we have got some error messages during restore. Please see our restore output:
[kalms4/root-ade ~]# /opt/CSCOpx/bin/perl /opt/CSCOpx/bin/res
resolver.pl restoreDBTableMig.pl restoreJRMMig.pl restorebackup.pl
[kalms4/root-ade ~]# /opt/CSCOpx/bin/perl /opt/CSCOpx/bin/restorebackup.pl -d /opt/BKP/
Restore started at : 2013/12/05 14:11:58
Please see '/var/adm/CSCOpx/log/restorebackup.log' for status.
USER ID is ..................................... : sysadmin
OS of the backup archive is..................... : Windows
INFO:The backup archive is from a different OS. Your current Platform is: Soft Appliance .
You are attempting to perform a Cross Platform Restore..
Do you wish to continue (Y/N) [Y] :Y
Generation to be restored is ................... : 0
Backup taken from............................... : /opt/BKP/
Common Services version in the backup data is... : 3.3.1
Common Services is installed in................. : /opt/CSCOpx
The temp folder for this restore program........ : /opt/CSCOpx/tempBackupData
Applications installed on this machine ......... : [Common Services][Campus Manager][Resource Manager Essentials][Device Fault Manager][cwportal][ipm][upm][cvw][cwlms]
Applications in the backup archive ............. : [Common Services][Campus Manager][Resource Manager Essentials][Device Fault Manager][opsxml][cwportal][ipm][upm][cvw]
WARNING: The list of applications installed on this CiscoWorks server does not match the list of
applications in the backup archive. If you restore data from this backup archive,it may
cause problems in the CiscoWorks applications.
Do you want to continue the restore operation? (y-continue or n-quit, y/n)?Y
Applications to be restored are................. : [Common Services] [Campus Manager] [Resource Manager Essentials] [Device Fault Manager] [cwportal] [ipm] [upm] [cvw]
Available disk space in NMSROOT................. : 86451488 Kb
Required disk space in NMSROOT.................. : 35906524 Kb
(The temp and NMSROOT are on same device, therefore this required disk space includes temp space)
Copying the backup files to the temporary location [/opt/CSCOpx/tempBackupData]
preRestore of [Common Services] has started.
preRestore of [Common Services] has completed.
preRestore of [Campus Manager] has started.
preRestore of [Campus Manager] has completed.
preRestore of [Resource Manager Essentials] has started.
preRestore of [Resource Manager Essentials] has completed.
preRestore of [Device Fault Manager] has started.
preRestore of [Device Fault Manager] has completed.
preRestore of [cwportal] has started.
preRestore of [cwportal] has completed.
preRestore of [ipm] has started.
preRestore of [ipm] has completed.
preRestore of [upm] has started.
preRestore of [upm] has completed.
preRestore of [cvw] has started.
preRestore of [cvw] has completed.
doRestore of [Common Services] has started.
Cross Platform Update started.
Cross Platform Update completed.
License check started.
WARNING: The license details in the server are different from the backup data.
After restoring, please check the license available in the server.
WARNING: Your current license count is lower than your earlier license count.
If you restore the data now, devices that exceed the current licence count
will be moved to Suspended state.
License check completed.
Restoring certificate.
WARNING: Cannot evaluate the hostname, hence the certificate
may be from this host or another host.
[ Certificate not overwritten ]
Restored Certificate.
Restoring Common Services database.
Restored Common Services database.
Restoring CMIC data.
Restored CMIC data.
Restoring CMC data.
Restored CMC data.
Restoring Security Settings.
Restored Security Settings.
Restoring DCR data.
Restored DCR data.
Restoring Certificate key store.
Restored Certificate key store.
Restoring DCNM CrossLaunch data.
Restored DCNM CrossLaunch function.
Restoring JAAS configuration.
Restored JAAS configuration.
JRM Job Migration started.
JRM job Migration done.
doRestore of [Common Services] has completed.
doRestore of [Campus Manager] has started.
Cross Platform Migration for Campus started.
Cross Platform update Starts for Campus
doRestore of [Campus Manager] has completed.
doRestore of [Resource Manager Essentials] has started.
10% of RME Restore completed
30% of RME Restore completed
50% of RME Restore completed
70% of RME Restore completed
100% of RME Restore completed
doRestore of [Resource Manager Essentials] has completed.
doRestore of [Device Fault Manager] has started.
10% of DFM Restore completed
30% of DFM Restore completed
50% of DFM Restore completed
80% of DFM Restore completed
Going to modify Eight PM report
Modified Sucessfully Eight PM report
100% of DFM Restore completed
doRestore of [Device Fault Manager] has completed.
doRestore of [cwportal] has started.
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.properties ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.script ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.log ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties//defaultUserCommunity.properties ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties//defaultCommunity.properties ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
doRestore of [cwportal] has completed.
doRestore of [ipm] has started.
10% of IPM Restore Completed
30% of IPM Restore Completed
50% of IPM Restore Completed
60% of IPM Restore Completed
70% of IPM Restore Completed
100% of IPM Restore Completed
doRestore of [ipm] has completed.
doRestore of [upm] has started.
HUM database restore starts
INFO:STOP= /opt/CSCOpx/objects/db/bin64/dbstop -q -y -c dsn=upm
SQL Anywhere Command File Hiding Utility Version 10.0.1.4239
INFO: Database Shutdown is in Progress..Please wait
INFO: Stop Engine Args= /opt/CSCOpx/objects/db/bin64/dbstop -q -y -c dsn=upm
INFO: After Database Shutdown RC= 2304
root=C:\PROGRA~2\CSCOpx\databases\upm\upm.db
DBUTILS: Inside Cross Platform
INFO: Current Database password does not match the password of Database being restored
INFO: Using the Password of the Database being restored
HUM database restore successfully completed.
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Threshold
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Threshold/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Custom
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Custom/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller_Failure
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller_Failure/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/TrendWatch
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/TrendWatch/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Availability
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Availability/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPORTUtilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPORTUtilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Utilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Utilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Memory_Utilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Memory_Utilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Availability
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Availability/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Threshold_Violations
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Threshold_Violations/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/CPU_Utilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/CPU_Utilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPSEConsumption
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPSEConsumption/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_ErrorRate
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_ErrorRate/README.txt
Directory is reportsStarted changing property .
linux
Restored HUM configuration file successfully.
doRestore of [upm] has completed.
doRestore of [cvw] has started.
doRestore of [cvw] has completed.
postRestore of [Common Services] has started.
postRestore of [Common Services] has completed.
postRestore of [Campus Manager] has started.
postRestore of [Campus Manager] has completed.
postRestore of [Resource Manager Essentials] has started.
postRestore of [Resource Manager Essentials] has completed.
postRestore of [Device Fault Manager] has started.
postRestore of [Device Fault Manager] has completed.
postRestore of [cwportal] has started.
postRestore of [cwportal] has completed.
postRestore of [ipm] has started.
postRestore of [ipm] has completed.
postRestore of [upm] has started.
postRestore of [upm] has completed.
postRestore of [cvw] has started.
postRestore of [cvw] has completed.
Restored successfully.
Are this errors going to affect our LMS 4.2 operations?
Then we have upgraded to LMS 4.2.2 and exported data and credentiales for PI import.
On PI 1.3 we have installed WCS 500 devices upgrade license and LMS 1500 upgrade license and now we are having 2000 devices lifecycle license. We have successfully restored WCS data in PI and we have imported LMS devices as bulk import. What is strange is that we have this message in prime regarding licensing:
On LMS 3.2 our customer had saved unlimited number of configuration versioning. After upgrading to LMS 4.2 we can only see last 3 configurations regardless of unlimided number of configurations in previous LMS, so my question is where can we find older configurations in LMS 4.2?
We are planning to turn unlimited versioning on CPI 1.3 now, so our customer will again have feature that they need. Do you have some experiance regarding disk space when all device configurations are stored forever?
Thank you for your help.
Regards,
Jelena -
WLC 2504 in Cisco Prime Infrastructure 1.2
Trying to add Cisco 2504 Wireless Controller, Software Version 7.3.101.0, to Cisco Prime Infrastructure
1.2 (1.2.0.103), License Evaluation, with no success.
When using Discovery, Discovery Job show Credential Errors: "Error occured due to invalid SNMP credential"
When Add Device from Device Work Center I get:
Reachability is "Unknown", Device Type is empty, Collection Status is "Managed with Warnings", with message "SNMP Failure: No Response for SNMP Get request.", Collection Time is empty.
I've tried with both snmp v2 and v3.
I've tried to lower "Maximum VarBinds per Get PDU" to 10 or 20, cause I've read similar problem in NCS.I solved the same problem 5min ago.!
select the device and press syc ..that helped me ...
Maybe you are looking for
-
Graphical Mapping Problem : Create Segments by conditions
Hi, i have a problem while mapping an incoming invoice to IDoc Invoic02. I had to create some Segments (E1EDP02) on basis of identifiers in the incoming message. I hope the following example i created will help to understand my exact problem: EXAMPLE
-
Permission denied message for parent directory
In Solaris 8 container I am facing the below issue. As oracle user when I do ls -l in /dboracle mountpoint getting permission denied error messages. $ ls -la ./..: Permission denied total 8 drwxrwx--- 8 oracle dba 1024 Feb 18 16:14 . drwxrwxr-x 6 ora
-
I want to make an app to fix my cell
it's not working how it's suppose to work
-
Having a problem with a iPhone 3GS. When I try to back it up on my pc or laptop it has a error message. We have other iPhones that will connect when plugged in. I need to back up my data on this iPhone so it can be serviced. Can anyone help?
-
Help about opening a PHP page from a Java application
Hi, I would have some elements to open a PHP page from a little Java application I'm doing. I would like to know the classes I had to use, how to implement them, ... In fact, I dial into my application my login, my password, and when I click on by "C