Prime Infrastructure 2.1 ASA5580- Security Context Partial Collection Failure
I am attempting to add my ASAs into prime but get stuck almost instantly after adding the new device. Prime is able to get the device name and Device type (Cisco ASA-5580 Adaptive Security Appliance Security Context) Admin status shows up as Managed but Inventory Collection Status shows up as "Partial Collection Failure" For more detail it says "feature_image_firewall Unexpected error. See the log file inventory.log for details."
The only failure in inventory.log I could find was
[2014-09-26 12:40:01,868] [ICE Service[ 1]Thread: 20] [inventory] [ERROR] - 192.168.0.19 For device id: 2848866 Feature = feature_image_firewall and Procedure = ImageFireWal failed in time 45 with the following error and continuing with other features: com.cisco.nm.expression.function.FunctionException: <palError><deviceId>2848866</deviceId><code>HANDLER_ERROR</code><message>Error while trying to run handler. Action : imageFireWall, Handler : com.cisco.nm.pal.customhandler.RPLHandler. Error : Exception thrown : Constraint violation. See log for details.</message><handlerCode>ERROR_HANDLER_ERROR</handlerCode></palError>
[2014-09-26 12:40:01,868] [ICE Service[ 1]Thread: 20] [ice] [ERROR] - com.cisco.nm.expression.function.FunctionException: <palError><deviceId>2848866</deviceId><code>HANDLER_ERROR</code><message>Error while trying to run handler. Action : imageFireWall, Handler : com.cisco.nm.pal.customhandler.RPLHandler. Error : Exception thrown : Constraint violation. See log for details.</message><handlerCode>ERROR_HANDLER_ERROR</handlerCode></palError>
com.cisco.nm.expression.function.FunctionException: <palError><deviceId>2848866</deviceId><code>HANDLER_ERROR</code><message>Error while trying to run handler. Action : imageFireWall, Handler : com.cisco.nm.pal.customhandler.RPLHandler. Error : Exception thrown : Constraint violation. See log for details.</message><handlerCode>ERROR_HANDLER_ERROR</handlerCode></palError>
As far as the ASA config goes:
snmp-server enable
snmp-server host management 192.168.10.27 community c!$c0PR!me version 2c
logging enable
logging history 7
snmp-server enable traps
The above config works on our ASA5520s except I still haven't set up the traps right because there isn't any useful information on those devices so I am not sure what I need to change?
My ASA is using DH 1.
For 9.2(1) I read this in the release notes.
Note The ASA 5510, ASA 5520, ASA 5540, ASA 5550, and ASA 5580 are not supported in this release or later. ASA Version 9.1 was the final release for these models.
Similar Messages
-
Hello,
I've got a strange behaviour regarding the inventory collection for 2 of 4 virtual switching systems.
That means the inventory collection for two VSS is succesfull (inventory collections status = Completed) for the other two systems it is not, see attachments.
The device credentials like SNMP-RW, SSH acces are OK. I've already tried to increase SNMP timout and retries as well as telnet/ssh timout without success
All 4 systems are identical regarding hardware model and software vesion.
HW: WS-C6509-E
SW: 12.2(33)SXJ3
Any ideas or suggestions?
Best regards,
BastianTAC and I found a bug, CSCum05301.
May be that is also helpfull for others.
https://tools.cisco.com/bugsearch/bug/CSCum05301/
Symptom:
Inventory collection will fail if following keywords are used as part on description command on the interface config level of IOS device: 1Gbps, 10Mbps etc.
Following error message is visible on the DWC:
Inventory Collection Status: Partial Collection Failure
Collection Status Failed feature(s)
Unable to configure DSL, Serial, POS, Ethernet, Loopback, Virtual-Interface, Tunnel, Vlan, Switchport and Service Module interfaces on ISR, ASR and Switches.
Conditions:
Speed keywords like 1Gbps, 10Mbps etc. available as part of descrption command in IOS interface level.
For example:
interface FastEthernet0/3
description 10Mbps
Workaround:
Use a space character between number and unit keyword, like 1 Gbps. -
Cisco Prime 2.1- Partial collection failure
Dear Experts,
We are seeing many devices (around 1000+ devices) showing as "partial collection failure". We found this coz of not updated Telnet/SSH Cli username and password. So instead of editing each and every device, is there any way to select all devices and update cli credentials in one shot..?
If someone helps me this option, it will be so helpful.Hi ,
Other way is to export all the devices , Edit it and then Import it.
Operate >device workcenter > EXPORT device \ BULK IMPORT
Thanks-
Afroz
****Ratings Encourages Contributors **** -
Partial collection Failure for nexus 5548UP in PI 2.1
Hi there,
I get "Partial Collection Failure" in the inventory collection status in Prime Infrastructure for all my Nexus 5548UP (8 devices).
i have seen in the PI 2.1 release notes that a bug CSCum16230 which look like my problem has been resolved in PI 2.1 but i continue getting the "partail collection failure"
Would like to know if the bug is still exist or get any other help to solve this problem.
Regards,
Alon.hello
I have this problem as well...
we've got four N5K-C5548UP. Two with a layer 3 daughter card and two without.
interestingly we see the issue just on those boxes with the l3 daughter cards N55-D160L3-V2 installed...
Any help or ideas are highly appreciated
regards
roman
Sh inventory:
OK:
device-a# sh module
Mod Ports Module-Type Model Status
1 32 O2 32X10GE/Modular Universal Pla N5K-C5548UP-SUP active *
3 0 O2 Non L3 Daughter Card N55-DL2 ok
Mod Sw Hw World-Wide-Name(s) (WWN)
1 5.1(3)N2(1c) 1.0 --
3 5.1(3)N2(1c) 1.0 --
NOT OK:
device-b# sh modu
Mod Ports Module-Type Model Status
1 32 O2 32X10GE/Modular Universal Pla N5K-C5548UP-SUP active *
3 0 O2 Daughter Card with L3 ASIC N55-D160L3-V2 ok
Mod Sw Hw World-Wide-Name(s) (WWN)
1 5.1(3)N2(1c) 1.0 --
3 5.1(3)N2(1c) 1.0 -- -
Cisco Prime Infrastructure 2.2: Catalyst 2960X-24TS-LL Switch Collection Failure
Hello,
I've Upgraded Prime Infrastructure to Version 2.2.0.0.158. Now our Catalyst 2960X-24TS-LL switches show an error message, when they are added to the inventory. The error is as follows:
Partial Collection Failure; Collection Status : Failed feature(s).
The 2960X-24TS-LL is listed under the supported devices list and other switches (e.g. WS-C2960X-48FPS-L) got inventorized without any problems.
Did anybody see this issue and can tell me how to solve it.
- Benjamin- Getting that one too, since running 2.2 (Failed Features) ; suggest opening a TAC case.
M. -
Prime Infrastructure issues with collection, dscp, mos, etc
We have a virtual Prime Infrastructure appliance installed. It currently shows collection status managed with warnings for several devices, i.e. Nexus 7k's, cat 3750x. cat 3850x. It is not all stacks though, most are collected accurately only a few are not showing up.
All four of my Nexus 7k's are not collected accurately.
Also when I goto Detail/Voice-video dashboards, I do not get any MOS, DSCP, voice call, IPSLA stats etc etc
Just for clarification we use Microsoft Lync for communications with Polycom phones using dscp 46, so perhaps it is not even possible but I wouod think Prime would be polling off of traffic on the port and look for DSCP values.
I am able to poll IPSLA and mos scores via PRTG.
on many of my ports in Detail Dashboards/Interface "polling enabled" shows as "no" I am not sure why it shows up as no but there is some date being polled.
Is there something simple I am missing? TAC does not seem to know the product and I am unable to find a decent manual. So I am at a loss.
Thanks in advance!Bump
-
Cisco Prime Infrastructure 2.0 : Nms:RAID - RAID is Bad Detect rebuild progress
Hi,
I'm having problem on our Cisco Prime Infrastructure 2.0 which is always happen HDD failure.
FYI, HDD failed at Slot 1.
This is details of message taken from our Cisco Prime alarms;
raid is bad detect rebuild progress... enclosure = 252 enclosure = 252 drive 255 is missing or bad
For your information, I was enter into RAID BIOS to saw the error. I got Slot:1, SAS, HDD, 278.464GB, Failed.
I also do the Rebuild drives on that HDD. After Rebuild is completed the HDD back to ONLINE.
But I still face the same problem for the next day.
Please help us to resolved the problem.
Thanks and Regrads.
Mohd Syukri Kaus
BIT Group Sdn BhdYou have the necessary CPU, memory and hard drive specifications for an Express size installation (Reference).
To install Prime Infrastructure 2.0 you will need to first install VMware ESX/ESXi. This is documented in the same Getting Started Guide I linked to above at this link.
Once you get that far along, just follow the setup wizard and installation is pretty simple.
FYI you will get better attention to Prime questions over in the Network Management forum. -
Prime infrastructure 2.0 - Inventory error with Virtual-Access Interface
Hi,
We have recently been trying to resolve a few issues with routers which get partial inventory failures upon discovery. I have managed to narrow this down slightly with the help of the inventory.log file. (With help from this post https://supportforums.cisco.com/thread/2255346 ) I have found the following happnes when this device is added:
[2014-03-04 14:00:27,537] [ICE Service[ 1]Thread: 29] [inventory] [ERROR] - 172.16.3.202 Object detected as SAME but DB Object obtained from the database is NULL For instance id: 0 For generated POJO: PPPEncapsulation[callBack=false,callIn=false,callOut=false,multilink=false,name=Virtual-Access1,oneTime=false,owningEntityId=69757688_172.16.3.202,preferedAuthType=NONE,deployPending=NONE,name=Virtual-Access1,owningEntityId=69757688_172.16.3.202,instanceId=0,_orderedListOEIndex=<Integer>,_creationOrderIndex=<Integer>,instanceVersion=0]
I have highlighted above where it mentions the problem with the virtual access interface. The configuration on the router is for PPPoE and the virtual-access1 interface is bound to Dialer0.
It then goes on to roll back the transaction:
172.16.3.202 persistObjects called with addList size = 307, updateList size = 6
172.16.3.202 Exception while persisting: com.cisco.xmp.persistence.common.util.DMMCRUDException:,message=errorId=12,componentName=CRUD Error Create Object Failed
172.16.3.202 Exception occured while inventory collection for device with id 69757688: com.cisco.xmp.inventory.ice.InventoryException: errorId=12,componentName=CRUD Error Create Object Failed
172.16.3.202 Done with collection. Total call method time: 15308
172.16.3.202 Rolling back the transaction
Has anyone else come accross this issue?
I have attched the log showing just messages from this device.
Thanks,
Mike.TAC and I found a bug, CSCum05301.
May be that is also helpfull for others.
https://tools.cisco.com/bugsearch/bug/CSCum05301/
Symptom:
Inventory collection will fail if following keywords are used as part on description command on the interface config level of IOS device: 1Gbps, 10Mbps etc.
Following error message is visible on the DWC:
Inventory Collection Status: Partial Collection Failure
Collection Status Failed feature(s)
Unable to configure DSL, Serial, POS, Ethernet, Loopback, Virtual-Interface, Tunnel, Vlan, Switchport and Service Module interfaces on ISR, ASR and Switches.
Conditions:
Speed keywords like 1Gbps, 10Mbps etc. available as part of descrption command in IOS interface level.
For example:
interface FastEthernet0/3
description 10Mbps
Workaround:
Use a space character between number and unit keyword, like 1 Gbps. -
Cisco Prime Infrastructure 2.0 and ASA 55xx platform
Hello,
We recently upgraded to Prime Infrastructure 2.0 with the hope being able to manage our ASA's from PRIME (and complete an LMS migration).
When I attempt to add ASA's to prime i get the following collection errors:
Unable to collect processor and RAM information. Processor and RAM information. Unexpected error. See the log file inventory.log for details.
In the logfile I get the following XML parsing error on the MIB:
<palError>
<deviceId>6284310032</deviceId>
<code>VALIDATION_ERROR</code>
<message>Failed to validate output XML: cvc-maxInclusive-valid: Value '3484331296' is not facet-valid with respect to maxInclusive '2147483647' for type 'int'.</message>
<result>
<result xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="/CISCO-MEMORY-POOL-MIB/xmp-im-file-system-module.xsd">
<xmp-im-file-system-module>
<MemoryPoolStatistics>
<memoryPoolIndex>1</memoryPoolIndex>
<free>4294967295</free>
<largestFree>4294967295</largestFree>
<used>3484331296</used>
</MemoryPoolStatistics>
To me it seems that the ASA returns a value that is bigger then int32 and thus causes an overflow? Any clues? Workarounds to add an ASA to Prime without checking these MIB'S?
Regards,
MarcelThe X series (all with 64-bit SMP images) are not currently supported by PI 2.0. We can hope for a device update in the coming months to remedy that situation.
If you click on the arrow next to the help icon in the top right of your PI and choose "Device Level Support" you will see:
Cisco ASA-5500 Series Adaptive Security Appliances
Features :
Topology
LLDP Neighbor Discovery
CDP Neighbor Discovery
Configuration
Configuration Archive
Software Image Management
Monitoring
Device Availability
Reachability
Inventory
Physical
System - Memory Pools
Interfaces - IP
Interfaces - Ethernet
Device Type
SYSOIDS
S/W Version
Software
Cisco ASA-5510 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.669
OID:1.3.6.1.4.1.9.12.3.1.3.447
Cisco ASA-5510 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.773
Cisco ASA-5520 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.670
OID:1.3.6.1.4.1.9.12.3.1.3.448
Cisco ASA-5520 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.671
Cisco ASA-5540 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.672
OID:1.3.6.1.4.1.9.12.3.1.3.449
Cisco ASA-5540 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.673
Cisco ASA-5560 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.12.3.1.3.454
Cisco ASA-5550 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.753
Cisco ASA-5550 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.763
Cisco ASA-5505 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.745
OID:1.3.6.1.4.1.9.12.3.1.3.560
Cisco ASA-5580 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.914
Cisco ASA-5585 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.1194
OID:1.3.6.1.4.1.9.1.1195
OID:1.3.6.1.4.1.9.1.1196
OID:1.3.6.1.4.1.9.1.1197
Cisco ASA-5585 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.1198
OID:1.3.6.1.4.1.9.1.1199
OID:1.3.6.1.4.1.9.1.1200
OID:1.3.6.1.4.1.9.1.1201
Cisco ASA-5585 Adaptive Security Appliance System Context
OID:1.3.6.1.4.1.9.1.1202
OID:1.3.6.1.4.1.9.1.1203
OID:1.3.6.1.4.1.9.1.1204
OID:1.3.6.1.4.1.9.1.1205
Cisco ASA-5580 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.915
Cisco ASA-5580 Adaptive Security Appliance System Context
OID:1.3.6.1.4.1.9.1.916 -
Prime Infrastructure 2.1 Client Statistic Report Issues
Hello Community,
I hope you can help with a couple of issues I am seeing on Prime Infrastructure 2.1, running an evaluation 60 day license.
My PI 2.1 build is currently managing a WLC 5508 running 7.4.121.0, which has been added successfully. No configuration changes were applied to the WLCs, other than SNMP community. No AVC or medianet configuration is applied.
When looking in the 'Operate>Client and Users' dashboard; I can see connected clients and if I select one of them, I can see further details like session, security and client statistics (showing traffic and 802.11 metrics). These are the table views that show current values, however, further down I see graphs but they do not contain any information for RSSI, SNR or traffic sent & received (packets or bytes).
Question: Should I see this information under an evaluation license and if so, what could be stopping it?
Also, when I run the reports 'Report>Report Launch Pad' and select 'Client>Client Traffic' or 'Client>Client Throughput' the resulting report contains 0 bps, when I select 'Report By' AP by Floor Area. I have created a single floor area and placed three access points into it.
Out of interest if I do a report of the same type using 'Report By' All or AP by Controller, I do see traffic graphs for 3 out of 333 access points. Just not the access points that are in my floor area. Also the amount of traffic utilization is tiny (less than a kbps) for a WLC with 800 users.
For a 'Client>Client Count' report using AP by Floor Area, I do see the client numbers connected to the WLC/APs in my configured floor area.
Question: Should I see reports for client traffic and throughput under an evaluation license for floor areas and if so, what could be stopping it?
I have checked the background task and the 'Client Statistics' task is enabled and run time is being updated.
Kind regards,
IanHi,
here is an update:
There are more than one Report you need to start to get data for Device, FAN, Power Supply, Module - look at these reports:
Report > Report Launch Pad > Device > Inventory
Report > Report Lauch Pad > Device > Wired Detailed Device Inventory
Report > Report Lauch Pad > Device > Wired Module Detail > Wired Module Detail Report Details
SFPs and GBICs cannot be reported til now - there are working on it.
br,
chris -
When is Cisco Prime Infrastructure 2.0 released, and what does 2.0 offer?
We are running Prime Infrastructure 1.3 primarily for wireless management at this point. We have enough licenses to add all our switches, routers, and firewalls, but we're hesitant to do so until 2.0 comes out. While there are some features for backing up and configuring switches and routers, 1.3 still seems pretty limited in regards to non-wireless features. For example, nearly every report in 1.3 is for wireless controllers or AP's, there are no reports I've found relevent for switches and routers. I've read a lot of blogs, cisco posts, and white papers talking about how Cisco Prime Infrastrucure 2.0 will finally consolidate Prime into a truly all-in-one network management suite that can manage the entire Cisco environment. Does anyone know when it's officially being released? Does anyone have an tech sheets on what's new in 2.0, or what its capabilities are? I want to better understand what 2.0 has to offer, when it's coming out, how to upgrade, so I can start planning for the upgrade and eventually importing all our network devices to Cisco Prime for centralized management. Any useful information or links would be appreciated.
Thanks,
ChristianPI 2.0 is in Beta mode for testing in closed group already. However it may still take some time to get released on CCO for FCS.
I think it is expected to be released between aug-sep. BU has also started working on CPI 2.1, which you can see test uploads on CCO.
For what does it have for customers?
> As Cisco have a vision of one network Management software for both wired and wireless infrastructure, which started getting real partially with Cisco PI.
As WCS got evolved to NCS and eventually to Cisco Prime Infrastructure, but it doesnt yet have full Management capability for wired infra., which is there with LMS.
With CPI 2.x Cisco plans to blend entire LMS and WCS features together.
-Thanks -
Cisco Prime Infrastructure 2.0 - no traps/info are pushed from devices
Good evening,
I have setup Cisco Prime Infrastructure 2.0 and, though I have added manually my 4 network cores as devices without any problem, I can't get a single trap or a single SNMP information to be pushed into my Cisco Prime Infra.
Here is my SNMP config on my core :
snmp-server user *edited* *edited* v3
snmp-server group *edited* v3 noauth notify *tv.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF0F
snmp-server community *edited* RO
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps flowmon
snmp-server enable traps transceiver all
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps rf
snmp-server enable traps memory
snmp-server enable traps cpu_threshold
snmp-server enable traps eigrp
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change nssa-trans-change
snmp-server enable traps ospf cisco-specific state-change shamlink interface
snmp-server enable traps ospf cisco-specific state-change shamlink neighbor
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps flex-links status
snmp-server enable traps fru-ctrl
snmp-server enable traps entity
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps ether-oam
snmp-server enable traps aaa_server
snmp-server enable traps flash insertion removal
snmp-server enable traps l2tc threshold sys-threshold
snmp-server enable traps power-ethernet police
snmp-server enable traps rep
snmp-server enable traps vswitch dual-active vsl
snmp-server enable traps udld link-fail-rpt status-change
snmp-server enable traps vtp
snmp-server enable traps vlancreate
snmp-server enable traps vlandelete
snmp-server enable traps auth-framework sec-violation
snmp-server enable traps dot1x auth-fail-vlan guest-vlan no-auth-fail-vlan no-guest-vlan
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps entity-diag boot-up-fail hm-test-recover hm-thresh-reached scheduled-test-fail
snmp-server enable traps port-security
snmp-server enable traps ethernet evc status create delete
snmp-server enable traps energywise
snmp-server enable traps ipsla
snmp-server enable traps vstack
snmp-server enable traps bfd
snmp-server enable traps bgp
snmp-server enable traps bulkstat collection transfer
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps ipmulticast
snmp-server enable traps isis
snmp-server enable traps msdp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
snmp-server enable traps syslog
snmp-server enable traps isakmp policy add
snmp-server enable traps isakmp policy delete
snmp-server enable traps isakmp tunnel start
snmp-server enable traps isakmp tunnel stop
snmp-server enable traps ipsec cryptomap add
snmp-server enable traps ipsec cryptomap delete
snmp-server enable traps ipsec cryptomap attach
snmp-server enable traps ipsec cryptomap detach
snmp-server enable traps ipsec tunnel start
snmp-server enable traps ipsec tunnel stop
snmp-server enable traps ipsec too-many-sas
snmp-server enable traps errdisable
snmp-server enable traps ethernet cfm alarm
snmp-server enable traps vlan-membership
snmp-server enable traps mac-notification change move threshold
snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down
snmp-server host *ip-address-edited* version 3 noauth *edited*
Basically all traps are enabled but absolutely nothing is showing up in my Prime Infra except that my 4 devices are "Reachable".
Here is a show snmp on the same device :
sh snmp
Chassis: *S/N Edited*
38554534 SNMP packets input
0 Bad SNMP version errors
14 Unknown community name
0 Illegal operation for community name supplied
0 Encoding errors
38453185 Number of requested variables
0 Number of altered variables
17790703 Get-request PDUs
20583581 Get-next PDUs
0 Set-request PDUs
0 Input queue packet drops (Maximum queue size 1000)
38490708 SNMP packets output
0 Too big errors (Maximum packet size 1500)
0 No such name errors
0 Bad values errors
0 General errors
38371069 Response PDUs
13 Trap PDUs
SNMP global trap: enabled
SNMP agent enabled
SNMP logging: enabled
Logging to *edited*, 0/10, 13 sent, 0 dropped.
Can anyone point out what is wrong or missing in my configuration? I can't seem to single it out myself.
Thanks
JeremyHi Jeremy,
SNMP traps are shown in the events and alerts section of PI.
SNMP config looks fine. Can you run the SNMP debug (debug snmp packets ) .check the logs and see if the device is actually sending the TRAPS to the PI server.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors **** -
Cisco Prime Infrastructure 2.2 Rest API XML does not add LF
I am using several scripts that dig the data from XML files created through Cisco Prime Infrastructure Rest API. It worked fine until 2.1. Now, with 2.2, seems Cisco stopped adding LF to each line and everything is 'one' line.
Here is an example with 2.1, there is a LF to the end of each line:
?xml version="1.0" encoding="UTF-8" standalone="yes"?>
<queryResponse type="AccessPointDetails" rootUrl="https://server/webacs/api/v1/data" requestUrl="https://server/webacs/api/v1/data/AccessPointDetails?type=contains(UnifiedAp)&.full=true&.maxResults=1000&.firstResult=0" responseType="listEntityInstances" count="715" first="0" last="714">
<entity url="https://server/webacs/api/v1/data/AccessPointDetails/1505569" type="AccessPointDetails" dtoType="accessPointDetailsDTO">
<accessPointDetailsDTO id="1505569" displayName="1505569">
<adminStatus>ENABLE</adminStatus>
<apType>AP1240</apType>
<cdpNeighbors>
<cdpNeighbor>
<capabilities>Switch IGMP </capabilities>
<duplex>Half Duplex</duplex>
<interfaceSpeed>100Mbps</interfaceSpeed>
<localPort>2</localPort>
<neighborIpAddress>10.1.1.1</neighborIpAddress>
<neighborName>switch</neighborName>
<neighborPort>FastEthernet0/1</neighborPort>
<platform>cisco WS-C3560-8PC</platform>
</cdpNeighbor>
Now, with 2.2, there is not LF anywhere:
?xml version="1.0" encoding="UTF-8" standalone="yes"?><queryResponse type="AccessPointDetails" rootUrl="https://server/webacs/api/v1/data" requestUrl="https://server/webacs/api/v1/data/AccessPointDetails?type=contains(UnifiedAp&.full=true&.maxResults=1000&.firstResult=0" responseType="listEntityInstances" count="715" first="0" last="714">
<entity url="https://server/webacs/api/v1/data/AccessPointDetails/1505569" type="AccessPointDetails" dtoType="accessPointDetailsDTO">
<accessPointDetailsDTO id="1505569" displayName="1505569"><adminStatus>ENABLE</adminStatus><apType>AP1240</apType><cdpNeighbors><cdpNeighbor>
Does anyone know, is this intentional or a mistake? Or is there a way how I control this?
I am reading on-line CPI Rest API docs, but seems cannot find anything.
Thanks,
VladPI 2.0 is in Beta mode for testing in closed group already. However it may still take some time to get released on CCO for FCS.
I think it is expected to be released between aug-sep. BU has also started working on CPI 2.1, which you can see test uploads on CCO.
For what does it have for customers?
> As Cisco have a vision of one network Management software for both wired and wireless infrastructure, which started getting real partially with Cisco PI.
As WCS got evolved to NCS and eventually to Cisco Prime Infrastructure, but it doesnt yet have full Management capability for wired infra., which is there with LMS.
With CPI 2.x Cisco plans to blend entire LMS and WCS features together.
-Thanks -
Configure the syslog of ASA 5512-X for display on Cisco Prime Infrastructure 2.1
Hi, I'm working on implementing the Cisco Prime Infrastructure 2.1 and want to display the syslog about ASA5512-X with Software Version 9.2.
What would be the procedure for configuring?
Thanks in advance.Hi,
Enable "logging host x.x.x.x " command to enable logging
check the below link:
http://www.cisco.com/c/en/us/td/docs/security/asa/asa91/configuration/general/asa_91_general_config/monitor_syslog.html#68764
FYI: Prime Infrastructure support only SEV 0,1,2 syslogs as of now.
Operate > alarm and events > syslogs
Thanks-
Afroz
****Ratings Encourages Contributors ***** -
Prime Infrastructure vulnerable to ShellShock?
Hi,
does anyone know if Prime Infrastructure version 1.2 is also affected?
It is not in the list:
http://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20140926-bash
KRHi Renata,
I'm looking for a patch for our version (and still looking) but found a list that appears to show that 1.2 is affected.
https://tools.cisco.com/bugsearch/bug/CSCur05228
Hope that helps.
Jim
Maybe you are looking for
-
AP Credit Memo and Purchase Order
Hi, can anyone tell me if it's possible to link a AP Credit Memo to a purchase order like an invoice can joined to ? thanks
-
HD icon not showing up in "test" user account
Hi All, I recently had problems with my MBP hard drive, which ultimately failed. I have since replaced it with a new 750 GB (7200 RPM) drive. I decided to create a "test" user account with admin privileges for troubleshooting purposes. However when I
-
Cannot find symbol even though it's there.
I am having an issue compiling a java class in oracle. I have a java class that will run an executable. I want to call that java class from a difference class and when I try to compile that class, it fails with Cannot Find Symbol. This is what errors
-
Format varchar2 column which stores a number and display it in 10,000 forma
Problem Description I am having a Standard VO , which has a varchar2 datatype attribute. In my view page i am dispaly this vo in a OATABLE. I want to foramt one of the varchar2 column to display it in a requried format Eg :- if the value in the colum
-
Hi Experts, I am working on a requirement where if i update the records in a table it will refelct in the other table..hence i need to dispaly a message whenever a record is updated stating the same. For this i m using a method. Now here are my querr