Prime Infrastructure 2.2 with Nexus 5672UP

Hi
I was wondering if anyone have managed to add Nexus 5672UP devices in Prime Infrastructure 2.2?
I noticed that it is not in the device supported list of 2.2.
I did however notice that the device is supported with Update Pack 7 in PI 2.1
Was wondering if one could load Update Pack 7 for PI 2.1 for PI 2.2 or if there is an update pack for PI 2.2 that includes this device?

Hi ,
Device Type: Nexus 5672UP
SYSOID: 1.3.6.1.4.1.9.12.3.1.3.1410
This device will be supported by first or second week of Feb.
Thanks-
Afroz
***Ratings Encourages Contributors ****

Similar Messages

Can i install Cisco prime infrastructure 1.3 with 1.1 license.

Can i install Cisco prime infrastructure 1.3 with 1.1 license.To be more precise it will be fresh installation
but the licenses I have is of 1.1.As per my overview from Cisco prime Infrastructure 1.2 NCS and NCS(WAN)
has been bundled into one service.But both were seperate entities in Cisco Prime Infrastructure 1.1.

It doesn't matter if you want to make a new installation or an upgrade. The questions is the license.
The base license is necessary for network management nodes (devices). But to get updates for your system you need the additional to your Base License the Lifecycle License (which can be ordered for 12, 24 or 36 months).
The Lifycycle License is also based on the number of managed devices. In your case 50 devices. So you have that License - congratulations!
Otherwise order the Lifecycle License for 50 devices (L-N-PI12-50-M). This generates CON-PSUU-PI12LF50 for 12 months, list price 414,81$. Then Upgrade from 1.1 to 1.2, patch the system and upgrade to 1.3.
Have fun,
Chris

Prime Infrastructure 2.0 and Nexus 5548, SSH credentials fail

Hi,
I'm having problem getting the Prime Infrastructure 2.0 to login with SSH to a Nexus 5548 to do an inventory. I get "Wrong Telnet/SSH credentials". But when I use the same credentials from another SSH-client it works fine. I also tested to SSH from the console of the Prime-server and that also works fine.
Any ideas???
Regards,
Stefan Lindkvist

I have PI 2.0 working against Nexus 5k's in two different installations. See below for an example (click to enlarge).
Have you put in an entry in both the login and enable fields (even though they are not separately required when logging in directly)?

Managing Prime Infrastructure 1.2 with MS IAS Radius

HI,
I have configured the PI 1.2il MS IAS radius server to authenticate machine with the management domain credentials.
When I needed to migrate the atuthenticatione from local to radius mode and I went to AAA and I select "with Radius server."
On the MS IAS I imported the tasks for users with role lobby ambassador and when I turned on the authentication mode in PI 1.2 with AAA Radius Server, the user was able to authenticate properly.
When I imported Admin or Root tasks on the server could not let the user management interface in Prime.
there is a documentation update?
Regards
Andrea

I wrote about this some time ago. Its based on NPS but you should be able to tweak it for IAS as well.
http://technologyordie.com/windows-nps-radius-authentication-of-cisco-prime-infrastructure
- Be sure to rate all helpful posts

Cisco Prime Infrastructure 1.2 with Cisco Prime Network Control System Hardware Appliance

Hi Team,
I have following BOM
Cisco Prime Infrastructure
R-PI-1.2-K9
Cisco Prime Infrastructure 1.2
1
R-PI-1.1-500-K9
Prime Infrastructure 1.2 Software - 500 Device Base Lic
1
L-PILMS42-500
Prime Infrastructure LMS 4.2 - 500 Device Base Lic
1
L-PINCS12-500
Prime Infrastructure NCS 1.2 - 500 Device Base Lic
1
PRIME-NCS-APL-K9
Cisco Prime Network Control System Hardware Appliance
1
PI-APL-IMAGE-1.2
Cisco Prime Infrastructure 1.2 Appliance Software
1
Pls let me know if we have both NCS and LMS preinstalled with Cisco Prime Infrastructure 1.2 Appliance Software orwe need seperate appliance or server for LMS 4.2.
Regards

Hi Scott,
Thanks for the response but I got to know that LMS and NCS are combined in single ISO image from PI 1.2 and can be installed on the same physical NCS appliance.
Can you pls check this.
Regards

Cisco Prime Infrastructure 1.2 with SNMPv3

Dears,
I am trying to add a router on Cisco Prime Infrastructure 1.2 using snmpv3 (authpriv, sha & aes256). When i go to device work center and add a device, i cannot find the AES-256 in the privacy options. Only None, DES, and AES-128 are available.
Is there any workarround?
Please advise.
Moustafa

PI only supports SNMP privacy up through AES-128 at this time. Reference the guide section on adding an new SNMP credential entry.
Additionally there is a bug with SNMP v3 support in PI 1.2. It should be resolved in PI 1.3.

Prime Infrastructure SSH password with space

Hi,
We have Prime Infrastructure 1.2 installed and now starting to populate the inventory with the devices list.
However, it seems like the system does not accept password with space character inside.
Anyone knows the fix / workaround to make this work?
Thanks.
Johannes

Hi ,
As Per my understanding there is No workaround ,you can try special characters ,however SPACES are Not allowed
Thanks
Afroz

Create a user on Cisco Prime Infrastructure 1.3 with a script ?

Hello, we have a visiting software that does not support Cisco Prime configuration.
I was thinking that maybe I can write a script or something like that to create a Wireless User Account when a visitor signs in at our reception.
Grabbing the login information from the database and then creating the account on the Cisco Prime.
The script will run on another computer so a VBScript or something like that would be best.
Is this possible ?
I have googled for hours now and have found the API site but cannot make sense of it.
I know how to get the information but inserting it in the Cisco Prime is what I am having trouble with.
Could anyone here help me with an example or steer me in the right direction to learn how to do this ?

Hi Hansruedi,
Thanks you for your help and your time.
I followed your recomandation until the fourth step.
But after this step, I lost the web page connection.
I check nsc status but all is running :
NMS still stopped. NMS must be running to have an access by web page ?
I restart Prime (by reload command) but nothing changed.
Thanks

Email Notifications on Prime Infrastructure 2.1

Hi Everyone,
I have a Cisco Prime Infrastructure 2.1 with almost 100 switches registered and managed properly. I have configured the Mail Server and alarm notifications are sent with no problems.
The deal is that I don´t want to recieve alarm mails for every single device that is registered. Is it possible to recieve mails just for a group of devices? I was checking the Cisco documents but could not find something clear about this.
Thanks for your help,
Ricardo

Hi Everyone,
I have a Cisco Prime Infrastructure 2.1 with almost 100 switches registered and managed properly. I have configured the Mail Server and alarm notifications are sent with no problems.
The deal is that I don´t want to recieve alarm mails for every single device that is registered. Is it possible to recieve mails just for a group of devices? I was checking the Cisco documents but could not find something clear about this.
Thanks for your help,
Ricardo

Cisco Prime Infrastructure - Assurance. Upgrade from 1.2 to 2.0

Hi,
We had purchased Prime Infrastructure 1.2 with SAU smartnet. Before we deployed 1.2 now I see 2.0 version is out and we qualify for upgrade license. However when I login to CCO to download the OVA file, I see 3 different editions. Express, Pro and Standard. Which one do I qualify to install? I have purchased following part numbers with 1.2 version.
R-PI12-K9     -     Qty 1
L-PI12-LF-100-LIC     -     Qty 1
L-PILMS42-100     -     Qty 1
L-PI12-LF-100     -     Qty 1
Thanks in advance,
Sam

Hi,
Check the below link for difference between [ Express, Pro and Standard ]
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/quickstart/guide/cpi_qsg.html#wp46865
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/quickstart/guide/cpi_qsg.html#wp75315
L-PI12-LF-100-LIC and
L-PI12-LF-100   :: Prime Infrastructure 1.2 - Lifecycle - 100 Device Lic PAK
are same as per my understanding and you can use these license to installed PI 2.0 with device count of 100.
Note: you can also add additional licenses(feature license ) for more Lifecycle (via R-PI12-K9 skus), which can be used for both Prime Infrastructure and LMS.
Thanks-
Afroz
[Do rate the post if you find it useful]

Cisco Prime Infrastructure 2.2 clients and users IPs not detected

Hi all,
I have cisco PI2.2 and discovered all the network and i notified that there are some clients' IPs (Servers or PCs or Laptops or ....) not detected.
please advice what may be the issue ?

Hi,
does anyone happen to know if that problem is fixed? My currently setup looks like this:
1. Cisco Prime Infrastructure 2.1 with updated device pack.
2. Assurance license
3. ASA5510 which has enabled netflow. Netflow is being sent to Cisco Prime 2.1
I do receive netflow raw data within Cisco Prime 2.1 but any graphical display of netflow data is not working. Does anybody has an idea where the problem is? Could it be that the graphical data is only displayed when sending netflow 1, netflow 5 or netflow 7?
regards
Maurus

MSE 3355 / PRIME INFRASTRUCTURE 2.1

I'm integrating a Cisco Prime Infrastructure 2.1 with MSE 3355 for location services and wIPS. I have several questions that I could not clear and would like you to help me giving me some indication with the steps I must take to fulfill these tasks.
1- The Maps added to the CI 2.1 are not showing the location of the Rogue APs and Rogue Clients seen in the network.
2.- The AP Clients location is not showed in the Maps.
3. I require to know what is the process for classifying Rogue APs in the PI 2.1.
5. I get the message "Collection Failure" of three WLC in the Cisco Prime Infrastructure but the data that the message shows is collected normally.

I have already resolved this two points:
1- The Maps added to the CI 2.1 are not showing the location of the Rogue APs and Rogue Clients seen in the network.
2.- The AP Clients location is not showed in the Maps.
I still have this questions:
3. I require to know what is the process for classifying Rogue APs in the PI 2.1.
5. I get the message "Collection Failure" of three WLC in the Cisco Prime Infrastructure but the data that the message shows is collected normally.
6.-We have this error message in the allocation profile for a WLC wIPS. (Note, this is WLC version 7.0.250.0)

Migrate from Prime LMS to Prime Infrastructure

I'm currently running CiscoWorks LMS 4.0.1 on Windows 2003 under VMware and just got upgrade licensing for Prime Infrastructure 1.2. I am assuming that I will need to upgrade the current server to Prime LMS 4.2 in order to ensure that data migration to Prime Infrastructure goes well. I am planning to follow Cisco's recommendation to run Prime LMS and Prime Infrastructure in parallel for a time and migrate individual functions.
My real question is about Syslog handling. All of the managed devices are currently sending Syslog data to LMS. As a last step in the migration, is it possible to change the IP address of the Prime Infrastructure server to replace the Prime LMS server so that the Prime Infrastructure server will just start getting all the Syslog data, or do I need to go change hundreds of managed devices to point to a new address?
Thanks for any help you can provide.

Putting LMS up against Prime Infrastructure is like comparing Apples to Oranges.
LMS is a very mature product and Prime Infrastructure is in it infancy stages...
My suggestion would be to leave the current LMS system up and running; bring a Prime Infrastructure server up with a Demo License; add a few of each type of device to your Prime Infrastructure server; setup a proof of concept scenario to prove you can do everything in Prime as you can do in LMS.

Cisco Prime Infrastructure 2.0 and ASA 55xx platform

Hello,
We recently upgraded to Prime Infrastructure 2.0 with the hope being able to manage our ASA's from PRIME (and complete an LMS migration).
When I attempt to add ASA's to prime i get the following collection errors:
Unable to collect processor and RAM information.          Processor and RAM information.          Unexpected error. See the log file inventory.log for details.
In the logfile I get the following XML parsing error on the MIB:
<palError>
<deviceId>6284310032</deviceId>
<code>VALIDATION_ERROR</code>
<message>Failed to validate output XML: cvc-maxInclusive-valid: Value '3484331296' is not facet-valid with respect to maxInclusive '2147483647' for type 'int'.</message>
<result>
    <result xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="/CISCO-MEMORY-POOL-MIB/xmp-im-file-system-module.xsd">
      <xmp-im-file-system-module>
        <MemoryPoolStatistics>
          <memoryPoolIndex>1</memoryPoolIndex>
          <free>4294967295</free>
          <largestFree>4294967295</largestFree>
          <used>3484331296</used>
        </MemoryPoolStatistics>
To me it seems that the ASA returns a value that is bigger then int32 and thus causes an overflow? Any clues? Workarounds to add an ASA to Prime without checking these MIB'S?
Regards,
Marcel

The X series (all with 64-bit SMP images) are not currently supported by PI 2.0. We can hope for a device update in the coming months to remedy that situation.
If you click on the arrow next to the help icon in the top right of your PI and choose "Device Level Support" you will see:
Cisco ASA-5500 Series Adaptive Security Appliances
Features :
Topology
LLDP Neighbor Discovery
CDP Neighbor Discovery
Configuration
Configuration Archive
Software Image Management
Monitoring
Device Availability
Reachability
Inventory
Physical
System - Memory Pools
Interfaces - IP
Interfaces - Ethernet
Device Type
SYSOIDS
S/W Version
Software
Cisco ASA-5510 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.669
OID:1.3.6.1.4.1.9.12.3.1.3.447
Cisco ASA-5510 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.773
Cisco ASA-5520 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.670
OID:1.3.6.1.4.1.9.12.3.1.3.448
Cisco ASA-5520 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.671
Cisco ASA-5540 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.672
OID:1.3.6.1.4.1.9.12.3.1.3.449
Cisco ASA-5540 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.673
Cisco ASA-5560 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.12.3.1.3.454
Cisco ASA-5550 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.753
Cisco ASA-5550 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.763
Cisco ASA-5505 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.745
OID:1.3.6.1.4.1.9.12.3.1.3.560
Cisco ASA-5580 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.914
Cisco ASA-5585 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.1194
OID:1.3.6.1.4.1.9.1.1195
OID:1.3.6.1.4.1.9.1.1196
OID:1.3.6.1.4.1.9.1.1197
Cisco ASA-5585 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.1198
OID:1.3.6.1.4.1.9.1.1199
OID:1.3.6.1.4.1.9.1.1200
OID:1.3.6.1.4.1.9.1.1201
Cisco ASA-5585 Adaptive Security Appliance System Context
OID:1.3.6.1.4.1.9.1.1202
OID:1.3.6.1.4.1.9.1.1203
OID:1.3.6.1.4.1.9.1.1204
OID:1.3.6.1.4.1.9.1.1205
Cisco ASA-5580 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.915
Cisco ASA-5580 Adaptive Security Appliance System Context
OID:1.3.6.1.4.1.9.1.916

Cisco Prime Infrastructure 2.0 and ASA 55xx platform problem

Hello,
We recently upgraded to Prime Infrastructure 2.0 with the hope being able to manage our ASA's from PRIME (and complete an LMS migration).
When I attempt to add ASA's to prime i get the following collection errors:
Unable to collect processor and RAM information.          Processor and RAM information.          Unexpected error. See the log file inventory.log for details.
In the logfile I get the following XML parsing error on the MIB:
<palError>
<deviceId>6284310032</deviceId>
<code>VALIDATION_ERROR</code>
<message>Failed to validate output XML: cvc-maxInclusive-valid: Value '3484331296' is not facet-valid with respect to maxInclusive '2147483647' for type 'int'.</message>
<result>
    <result xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="/CISCO-MEMORY-POOL-MIB/xmp-im-file-system-module.xsd">
      <xmp-im-file-system-module>
        <MemoryPoolStatistics>
          <memoryPoolIndex>1</memoryPoolIndex>
          <free>4294967295</free>
          <largestFree>4294967295</largestFree>
          <used>3484331296</used>
        </MemoryPoolStatistics>
To me it seems that the ASA returns a value that is bigger then int32 and thus causes an overflow? Any clues? Workarounds to add an ASA to Prime without checking these MIB'S?
Regards,
Marcel

Hi,
does anyone happen to know if that problem is fixed? My currently setup looks like this:
1. Cisco Prime Infrastructure 2.1 with updated device pack.
2. Assurance license
3. ASA5510 which has enabled netflow. Netflow is being sent to Cisco Prime 2.1
I do receive netflow raw data within Cisco Prime 2.1 but any graphical display of netflow data is not working. Does anybody has an idea where the problem is? Could it be that the graphical data is only displayed when sending netflow 1, netflow 5 or netflow 7?
regards
Maurus

Prime Infrastructure 2.2 with Nexus 5672UP

Similar Messages

Maybe you are looking for