Prime Infrastructure supported Routers on small OVA

Hello:
Has any one seen PI small deployment managing routers too?
PI Supports most of the models, but, the documentation says that it needs Extra Large OVA for 5,000 ISR Routers, (but for small, medium and large OVA , it says  ISR Routers: 0).
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/1.2/quickstart/guide/cpi_qsg.html#wp75828
Does anybody know if a small or medium OVA can support, lets say, 150 routers?
Thanks on advanced
JE

The PI documentation is lagging a bit - the only requirements for the current release are what's in the Quick Start Guide here.
There is no requirement for dedicated cores. As long as your VM meets the hardware specification of the QSG, your installation should be OK. (Of course, it doesn't hurt to provide more than the minimum requirements.)

Similar Messages

  • Is cisco prime infrastructure support / can be run as syslog server?

    Dear All,
    is cisco prime infrastructure support / can be run as syslog server?
    and,
    where i can see network topology diagram, using cisco prime infrastructure?
    many thanks,
    Jerri

    Hello. Cisco Prime LMS will be replaced by Cisco Prime Infrastructure in the near future.
    In the current release of Cisco Prime Infrastructure you can't use topology diagrams. This feature is in roadmap.
    About syslog, you can send syslogs to Cisco Prime Infrastructure, but I don't recommend using it as syslog server. Please see this link for more information https://supportforums.cisco.com/thread/2179520
    Please rate if this helps

  • Does Cisco Prime Infrastructure supports monitoring CPU,Memory, HDD for UCS , VMWare?

    Does Cisco Prime Infrastructure supports monitoring CPU,Memory, HDD for UCS , VMWare?

    Prime Infrastructure/ Assurance is  positioned today more towards managing network elements and network performance,  rather than server infrastructure. We are in the process of adding Datacenter  component support, with more focus on Nexus and UCS- due later this  year.
    Having said that, Prime Infrastructure allows the system user to  add custom SNMP polling templates, which can then be used for polling any SNMP  based values from any SNMP enabled device. These can be used to collect the  information you specified below and the polled information will be available in  dashboards and reports.

  • Which version of prime infrastructure supports wlc5508 ver 7.4?

    Thanks
    Sent from Cisco Technical Support iPhone App

    PI 1.3
    Here is the compatibility matrix.
    http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html
    Sent from Cisco Technical Support iPhone App

  • Upgrading prime infrastructure 2.1.0.0.78 - 2.1 cannot do app backup

    Hi All
    Trying to do an upgrade prime 2.1.0.0.78  to prime 2.2.
    I have saved an app backup off the exisitng prime 2.1.0.0.78
    However when i try to restore to the new prime infra 2.2 
    with the backup from the 2.1.0.0.78 it fails with a database error
    My technical support say i should change the new vm server
    to match ip addresses etc with the old one but that cant be right
    as this is the official blurb for the types of backups ...
    Application backups: These contain all Prime Infrastructure application data, but do not include host-specific settings, such as the server hostname and IP address. Application backups are intended for use when Prime Infrastructure is running as an OVA on customer-supplied hardware, as restoring from the backup may need to be to a server with completely different host settings.
    Appliance backups: These contain all application data and host-specific settings, including the hostname, IP address, subnet mask, and default gateway. Appliance backups are intended for use when Prime Infrastructure is running on a Cisco-supplied appliance, and restoration is most likely to be to a server with the same host settings.  
    I am obviously using the application backups
    Kind regards
    Steve

    Here you go ....
    Initiating restore.  Please wait...
      Restore Started at 02/02/15 17:29:54
      Stage 1 of 9: Transferring backup file ... 
      -- completed at 02/02/15 17:30:59
      Stage 2 of 9: Decrypting backup file ...
      -- completed at  02/02/15 17:34:00
      Stage 3 of 9: Unpacking backup file ...
      -- completed at  02/02/15 17:34:01
    Stopping strongSwan IPsec failed: starter is not running
      Stage 4 of 9: Decompressing backup ...
      -- completed at  02/02/15 17:34:31
      Stage 5 of 9: Restoring Support Files ...
      -- completed at  02/02/15 17:34:32
      Stage 6 of 9: Restoring Database Files ...
      -- completed at  02/02/15 17:34:51
      Stage 7 of 9: Recovering Database ...
      Error while restoring and recovering database, please check the logs.

  • Configure the syslog of ASA 5512-X for display on Cisco Prime Infrastructure 2.1

    Hi, I'm working on implementing the Cisco Prime Infrastructure 2.1 and want to display the syslog about ASA5512-X with Software Version 9.2.
    What would be the procedure for configuring?
    Thanks in advance.

    Hi,
    Enable "logging host x.x.x.x "  command to enable logging
    check the below link:
    http://www.cisco.com/c/en/us/td/docs/security/asa/asa91/configuration/general/asa_91_general_config/monitor_syslog.html#68764
    FYI: Prime Infrastructure support only SEV 0,1,2 syslogs as of now.
    Operate > alarm and events > syslogs
    Thanks-
    Afroz
    ****Ratings Encourages Contributors *****

  • Prime Infrastructure- switch interface up/down history statistics.

    Hi. Does Prime Infrastructure support a way of showing when some specific interface was last seen up/down?
    For example I need to know which interfaces are not used very often (that are in the down state most of the time).
    Thanks!

    Pawel,
    Unfortunately PI 2.1 (and 2.2) do not yet allow us to define automated actions in the event of a specific syslog message being received.

  • Cisco Prime Infrastructure multitenancy?

    Hi can someone please give me an indication if Cisco Prime Infrastructure supports multitenancy? and if so how this is achieved?
    I would like to monitor/managed multiple customers who may have overlapping private IP subnets
    Thanks

    Hi,
    With CPI v2.0 there is a multi-customer license:
    "L-PI2X-MSP-1 Cisco Prime Infrastructure 2.x Multicustomer 1 Customer RTU"
    What is this license intended for?
    Is it safe to assume that CPI v2.0 also does not support multi tenancy?
    Then there is CPI v2.0 for Service Providers.
    "R-PI2X-SP-K9 Cisco Prime Infrastructure 2.x Service Provider"
    Is this version multi tenant capable?
    What is the difference between the two?
    Thanks.

  • What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP's?

    What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP’s?

    • PI provides visibility for autonomous  clients within the same list view as lightweight and wired clients (client list  page).
    • Rogue AP detection for autonomous AP's is not supported (it's  supported in CUWN). 
    • Alarms/events for client authentication issues (e.g.  authentication failure) are displayed in PI.
    • Config management for  autonomous AP's is via CLI template.  Config comparison and archiving  functionality in PI leverages these same features that were brought in from LMS,  so need to defer to others in terms of whether this is a cross-platform feature  in PI or is only supported on a subset of platforms.  Config comparison/archive  is supported in CUWN.PI supports both infrastructure (e.g. AP Tx Power and  Channel, busiest AP, AP utilization, etc.) and client (e.g. client count, client  sessions, etc.) reports, and there are extensive reports for CUWN

  • Does Prime Infrastructure 2.0 support 7.5 code?

    I am currently running PI 1.3 and plan on upgrading to PI 2.0. Are 5508 Wireless Controllers 7.5 and MSE 7.5 code supported in release PI 2.0?

    PI 2.0 was really intended for the converged access, but it will also support v7.5 and PI1.4 supported v7.5.
    Management Support for WLC Release 7.5
    Prime Infrastructure 1.4 provides management support for WLC Release 7.5 and associated features. In addition, this release provides support for AP platforms such as 3600P and 802.11ac module.
    For more information about Cisco Unified Wireless Network (CUWN) Software Release 7.5, see the product bulletin at the following URL:
    http://www.cisco.com/en/US/products/hw/modules/ps2797/prod_bulletins_list.html
    For more information about the features of WLC Release 7.5, read the Release Notes for Cisco Wireless LAN Controllers and Lightweight Access Points for Release 7.5 available at the following URL:
    http://www.cisco.com/en/US/products/ps10315/prod_release_notes_list.html

  • Prime Infrastructure 2.0: Open Database Schema Support available?

    Hello,
    I searched the forum for an Open Database Schema Support for PI.
    I only found Open Database Schemas for the Cisco Works LAN Managemet Solutions and Cisco Prime LAN Managemet Solutions.
    Exists an open Database Schema Support for Prime Infrastructure 2.0 as it exists for the older LAN Managemet Solutions ?
    Thanks.
    Bastian

    Programmatic interface to Prime Infrastructure is done via the the REST API vs. any open database schema.
    There are published reference guides here. For the most up to date information, please see your PI server itself. In Lifecycle view, the help menu has a link to the server-based API information:

  • UPS monitoring support with Cisco Prime Infrastructure 1.2

    Dear Members,
    Good day,
    I am having a project implemented wherein i have the UPS power redudancy solution for our network devices.
    Now can anyone gide that is it possible for below :-
    UPS units installed with SNMP cards be monitored via Cisco Prime Infrastructure 1.2 as our monitoring & management solution is Cisco Prime Infrastructure 1.2 ?
    if yes
    Can you guide if following action would be possible to export the below logs from UPS unit to our Cisco Prime Infrastructure 1.2
       a) UPS fault status information
       b) UPS operational status(input power available Y/N)
       c) Battery fault status
       d) Battery charging current
       e) Battery charge level
       f) Output current
    Conclusion is we need to confirm that would it be posible to achieve remote monitoring of these UPS units via our CPI 1.2
    Thanks in Advance for your support & replies to this query.
    Regards,
    Muzammil N.

    Prime Infrastructure 1.2 can manage non-Cisco devices in a limited fashion via SNMP query and trap processing. It cannot import logs and does not have a generic syslog server,
    So if your devices have snmp read only support and can generate SNMP traps for the above you can add them to PI. Follow the manual add device procedure here.

  • Cisco Prime Infrastructure 1.2 OVA not found

    Hi all,
    I want to download Cisco Prime Infrastructure 1.2 OVA but I can't find it, there is just  "Cisco Prime Infrastructure 1.2 Plug and Play for Virtual Appliance " . Is this the right OVA ?
    Thanks for your help
    BR
    Aaziz

    Hi Aaziz,
    Unfortunately this download of this file is not available anymore on cisco.com site.
    As an alternative, you can download PI 1.3 OVA, where you can find the same features and
    interface:
    http://software.cisco.com/download/release.html?mdfid=284652876&softwareid=284272932&relea
    se=1.3&relind=AVAILABLE&rellifecycle=&reltype=all
    Note:  you can use the same license of PI 1.2 on PI 1.3
    Thanks-
    Afroz
    ***Ratings Encourages Contributors ***

  • Cisco Prime Infrastructure 2.2 UCS support (C24)

    Hi,
    I recently upgraded a CPI 2.1 server to 2.2 hoping that it would support monitoring and managing a customer's C24 server. Unfortunately I hadn't read the Supported Devices list (http://www.cisco.com/c/en/us/support/cloud-systems-management/prime-infrastructure/products-device-support-tables-list.html) where it is stated that UCS C220 M3 and C240 M3 are supported, but none of the other models.
    When can I expect support for C24 M3 (OID:1.3.6.1.4.1.9.1.1685) and the other UCS models?
    Mikael

    Cisco just added the Compute work center and UCS support in PI 2.2. I suspect they used the C220 as a first target since that's the platform for the upcoming hardware appliance refresh.
    While they haven't announced future release plans, typically we see incremental device updates via the update packages - those have been coming out almost monthly with PI 2.1.
    I'd encourage you to submit enhancement requests via your Cisco account team if the feature is important to you. Customer feedback is one of the key elements in deciding what features the developers focus on.

  • Cisco nexus 6001 not a supported device on cisco prime infrastructure 2.1?

    I have installed Cisco Prime Infrastructure 2.2 and Prime Infrastructure still doesn't seem to support the Nexus 6001 platform? Can someone tell me if Cisco Prime Infrastructure will ever support the Cisco Nexus 6001 platform or is there any plans to support it in any future device packs? 

    The Nexus 6001 isn't currently supported in PI 2.1. There's no workaround except to wait for a device or product update that adds support. Right now I know the 9000 series is on the 2.2 roadmap but I haven't seen any reference to the 6001 and PI.
    Interestingly, Prime LMS does support both the 6001 and 6004. Reference.

Maybe you are looking for

  • My iPod displays black & white battery charge icon and sad iPod face. help!

    I plugged my iPod into an older iMac; it froze and had to be restarted. I restarted it and started listening on shuffle. It would skip through all of my songs without me pressing any buttons. I restarted again and it worked fine. I came home and plug

  • Selecting Row from Rowset

    I have a rowset (table) displayed, and I want the user to be able to click on any row in the displayed table, thereby selecting that row. I tried using a button as the component type in the table layout, but where do I extract the value from? xxxRowS

  • HT1267 how can check my lost iphone is on by imei number tell me

    how can check my lost iphone is on by imei number tell me

  • Portal Login ID in ABAP

    Hi, consider a scenario. I am login into Enterprise portal using - admin_it. I want to know by which user has login into portal. By which method or function can i read this login id into abap. Regards, Priya

  • Screen shifts 1/4" to 3/4" and will not respond

    I have an IMac running OS X Version 10.9.3 with a 3.06 GHz Intel Core 2 Duo with 8 GB 1067 MHz DDR3 memory. It has a 500 GB hard drive with 256 GB used and 242 GB available. The problem is that while using Safari, Mail, Word, Pages, most any program,