Prime LMS 4.2.1 Netconfig and Template TFTP/SSH issue

I have cisco Prime 4.2.1 installed and am trying to deploy templates and Adhoc Netconfigs. The jobs are failing with the following message:
Command(s) failed on the device TFTP: Failed on the device. SSH: Failed to establish SSH connection to 10.104.114.231 - Cause: Authentication failed on device 3 times.
If I deploy a Netconfig Task, say just adding a Syslog Server to the same switch it succeeds, no problem.
I am using Cisco ACS 5.2 - TACACS and have configured the tacacspromtps.ini file for the username and password prompt. I can log onto the switch with the Prime Account no problem using Telnet. SSH has not been configured on the switch. I can't find where the protocols for connecting to devices are configured within Prime LMS?

hi gary,
based on my understanding, its because the device is not configured with SSH.
is the device running SSH enabled (K2 or K9) image? if yes, you can enable the SSH.
if no, then perhaps you want to try find it here to change it to telnet
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/user/guide/configuration/appa.html
regards,

Similar Messages

Prime LMS 4.1 and VMWARE ESX 5.0

Can Cisco Prime LMS 4.1 be deployed on VMware ESX server 5.0 or not ?

No LMS 4.1 is not supported on ESXi 5.0. LMS 4.1 supports the following Virtualization Systems:
•VMware ESX server 3.0.x
•VMware ESX Server 3.5.x
•VMWare ESX Server 4.0.x
•VMWare ESX Server 4.1
•VMWare ESXi Server 4.0
•VMware ESXi Server 4.1
•Hyper V Virtualization (As an installable in Windows 2008)
For more details check:
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.1/install/guide/prereq.html#wp1119955
On a side note, though a OVF/OVA file may be an issue, but you can try to install LMS 4.1 on a virtualized Win/Sol guest OS host, where it should work mostly. But for any issues further, Cisco or TAC may refer to this as an unsupported installation, for any t/s or support.
Else, you may upgrade to LMS 4.2 which is supported on ESXi 5.0.
-Thanks

Upgrade Cisco Prime LMS 4.0 to Cisco Prime Infrastructure 2.1

My company has asked me to migrate Prime LMS 4.0 to Prime Infrastructure 2.0 for a client and can not find the guide, the questions are? the migration is possible without an intermediate step? and There is a guide to update LMS 4.0 to PI 2.0 ??
Thanks in advance.

Prime LMS 4.2.2 added support for the PI template directly:
Export Data for Prime Infrastructure
Cisco Prime LAN Management Solution supports data migration to Prime Infrastructure 1.2. This feature enables user to export the Device Credentials Repository (DCR) data from LMS 4.2.x versions to Prime Infrastructure 1.2. The data backup status and backup location are displayed at the bottom of the Export Data for Prime Infrastructure page. The data being exported from LMS and the data imported back to PI are listed as follows.
Data exported from LMS
•Device Credentials Repository (DCR)
•Software Image Management
•Config Archive
•Change Audit
•Syslog
Data Imported to PI
Device Credentials Repository

Cisco Prime LMS ordering

Hi,
I need to order WCS and LMS for a new network. But after going through the datasheet, I found it is now bundled as Cisco Prime Infrastructure. I am confused in selecting the device counts. If I need to manage 140 access points and 100 network devices, how much device license i should order for Cisco Prime infrastructure.
When i select 100 license for the part number R-PI-1.1-100-K9, i am getting 100 NCS license and 100 LMS license as included items, so for my above scenario, if i order 150 license for prime infrastructure, will it cover all 240 devices?
Many thanks....
Abdul Rasheeth.

Cisco Prime LMS does NOT have the WAN QoS deployment capabilities packaged up nicely the way QPM did. It does, however, offer the Auto Smartports and MediaNet work centers that aid in setting up (primarily) endpoint switch ports. See this link for more details.
I believe the best one could do with respect to MAN/WAN devices' QoS settings using LMS would be to create deployment templates and do compliance checks.

Gestion con Cisco Prime LMS

Hola,
Por favor, tengo un par de preguntas con el Cisco Prime LMS:
Primero: Puedo monitorear equipos que no son de Cisco?
Segundo: Puedo monitorear temperatura de loos equipos con LMS o debe ser Network?
Gracias

Cisco Prime LMS does NOT have the WAN QoS deployment capabilities packaged up nicely the way QPM did. It does, however, offer the Auto Smartports and MediaNet work centers that aid in setting up (primarily) endpoint switch ports. See this link for more details.
I believe the best one could do with respect to MAN/WAN devices' QoS settings using LMS would be to create deployment templates and do compliance checks.

Prime LMS: HUM performance monitoring interface selection

Hi @all,
I am uisng Prime LMS 4.2.5. We want to monitor the performance of interfaces (in and out discards, utilization etc.)
Is it possible to select other interfaces than the "Link Ports"? I want to monitor some server ports.
I have created my own group, but this one cannot be selected in the threshold configuration.
Regards
Joerg

You can select the other ports/interfaces when while creating poller, you'll see following options :
Poll by Pattern  Select patterns on which you want to query devices and poll instances
Poll all Instances  Poll all instances of the selected template on the selected devices
Poll by User Selection  Select the instances on which you want to poll the devices
Select the Poll by user Selection to select the desired interfaces. It Polls the selected instances of the device. You cannot select this preference type for Device Groups and Port Groups data sources.
-Thanks
Vinod

Issues with Cisco Prime LMS 4.2.3

Hi,
I'm trailing Cisco Prime LMS 4.2.3 Soft appliance on ESXi before I deploy it into a live environment and am having some issues.
I've upgraded to version 4.2.3 and the box was working fine after the upgrade however on power it up today the Apache service will not start.
If I look at the LMS application I see this for the Apache service.
"Apache Administrator has shut down this server 0 "
I have tried to starting it.
CiscoLMS42/admin# application start Apache
% Application failed to start
CiscoLMS42/admin#
If I run an application operation debug at the same time I get the following output.
CiscoLMS42/admin# 6 [5343]: application:operation cars_install.c[1145] [admin]: Application initialization initiated for appname: Apache, operation: 0
7 [5343]: application:operation cars_install.c[1146] [admin]: Operations: O-APP_START, 1-APP_STOP, 2-APP_STATUS
6 [5343]: application:operation cars_install.c[1150] [admin]: Verifying app (Apache) is installed ...
3 [5343]: application:operation cars_install.c[1152] [admin]: App (Apache) is not installed.
3 [5343]: application:operation install_cli.c[281] [admin]: Error while starting application - Application: Apache ErrorCode: -999
I'm at a complete lose as to where to look next, failing anything else I'll have to rebuild it, but it would be nice to know how to get the Apache up and running again.
regards
Rich

Hi Richard,
I see the following:
[ Thu Apr 18 20:53:11 GMT 2013 ] TomcatMonitor After gettingAJPPort : ajpPort = 9009 and host =CiscoLMS42
[ Thu Apr 18 20:53:11 GMT 2013 ] TomcatMonitor theMgr constructor successful.
[ Thu Apr 18 20:53:11 GMT 2013 ] TomcatMonitor Inside whileloop
[ Thu Apr 18 20:53:11 GMT 2013 ] TomcatMonitor Tomcat is not ready, it's coming up Connection refused
It looks like the hostname cannot be resolved. Can you try to add a static entry in /etc/hosts for the IP of the server and CiscoLMS42?
Restart the daemon manager and it should work.
Regards,
Vlad
==========
NMS Team
Krakow, Poland
Cisco TAC

Any way to find unused ports in Prime LMS 4.2.3 ?

Hi all,
We have just installed Prime LMS 4.2.3 (about a week ago), and it is pretty much working as expected, except for one thing - I cannot get any data back from the reclaim ports report.
I have tried both the Ports Up and Ports Down options, and have even taken the time frame down to one day, but always receive a "no records" result. Has anyone got this working?
Pretty much every other report I've tried so far returns results, just not this one.... We really need to use it to determine (over a period of time) what our actual port usage is for our replacement schedule over the next few years.
-Pete

Hi Afroz,
The detailed device report is really useful, as it contains the time of the port change - I ran it for the switch I was interested in, and then exported the data into Excel and sorted on port status and change date to get the info I needed.
I also ran the "Reclaim up ports" again with the interval set for 15 days with zero result, however when I changed this to 5 days I started to get some info - my guess is that the data that is needed for this report is collected once every week or so.
My server has been running for nearly two weeks now, so I will let it do it's thing for about a month, then run the report again to get some better statistics.
Thanks for your suggestions, much appreciated !
-Pete

Problems getting Prime LMS to start up

Just got the Cisco Prime Lan NMS software. Getting this error when I try to turn up the appliance after I deployed it in ESXi -
Power On virtual machine:Failed to power on VM.
See the error stack for details on the cause of this problem.
Time: 7/16/2013 9:32:26 AM
Target: Cisco Prime LAN Management Solution
ESXi: ucs-c1b4
Error Stack
Failed to power on VM.
Could not power on VM : CPU min outside valid range.
Group host/user: Invalid CPU allocation requested for VM vmm0:Cisco_Prime_LAN_Management_Solution. (min: 4520 mhz, max: -1, minLimit: -1, shares: -3)
SharedArea: Unable to find 'testSharedAreaPtr' in SHARED_PER_VM_VMX area.
This is being deployed on a Cisco UCS B200 M3 with 128GB of ram. There is nothing else deployed on this blade. I elected for thin provisioning on disk storage.
Wouldnt expect that I would have to tweak the install any.
Suggestions ?

5.1 is not supported - only 4.1 and 5.0 (reference). That's most likely the root cause.
I didn't have any specific information for Prime LMS OVA but even though some folks have reported success with Prime Infrastructure 1.3 on 5.1, the product managers told me at Cisco Live that 5.1 would not be supported until PI 2.0. If they ever release an LMS 4.3 (TBD), it might have ESX 5.1 support.

Prime LMS 4.2 installation with solaris 10 volume manager

Hello
Is it possible to use Solaris Volume Manager for disk mirroring in prime LMS 4.2 installation over sparc arquitecture?
This is intended for having hard disk redundancy support.
Is there any documented reference?
O.S. Solaris 10 08/11
Cisco prime LMS 4.2
Regards

They were not tested together, and I recommend they not be installed on the same zone instance (due to potential conflicts). Now, if you're certain you have a server that can accommodate both suites (in terms of resources), create separate zones for each suite. This will eliminate the conflict possibility while still giving you one overall physical machine to manage.

LMS 4.2.1: Save and Reset Button not woking on Syslog Purge Settings page

Hello,
Did anyone notice that Save button is not woking on Syslog Purge Settings page (Admin > Network > Purge Settings > Syslog Purge Settings) when Email: field is not empty. An Reset button is not working at all.This is the Cisco Prime LMS 4.2.1.
Is it only my LMS server or you all have this bug?
Regards,
Marija

I did a test on a system (LMS 4.2.1, W2k8 R2) and had the same issue, so this really looks like a bug in the GUI;

LMS 4.2.3 device and system update failing

I have upgraded to prime LMS 4.2.2 (from 4.0.1) and can not perform system or device upgrade. Using wireshark I can see why. it looks like LMS is trying to go to this old web link http://cco.cisco.com/cgi-bin/login to get software. I believe this was fixed years ago in bug CSCto46927.
Can I reapply bug fix CSCto46927 on 4.2.3 or is there another fix?
Thanks.

"It is fixed now and the issue should resolve for all the LMS server's."
Are you sure?
The error message is missed, so I asume the web page is answered correctly,
but something is wrong with package checking.
For example, at my LMS 4.2.3 the ASA package is 7.0. After checking it shows there is no package to update (Popup - "No updates available in Cisco.com for selected products")
Tcpdump shows:
            284259296
            Cisco Prime LAN Management Solution 4.2
                    283418817
                    LMS Inventory Config And Image Management Device Package Updates
                            ASA(7-1)
                            ASA(7-1)
                                7
                                4.2.2
                                1
So there is an update to 7.1. Same problem with NAM (my ver is 6.0) and the newswest at cisco.com is NAM 6.1,
On the other hand the " 4.2.2" is weird.
If a have a newer (patched) version, the packages are not available to me??
Dont understand...

Prime LMS 4.2 to Prime Infrastructure 2.0 license migration

A couple of months ago I upgraded WCS to Prime Infrastructure (WCS via NCS to PI 1.2 at that time). Meanwhile PI is running version 2.0. For some reason, when purchasing the upgrade licenses, I also got a 500 device LMS4.2 upgrade license.
The exact part numbers were:
R-W-PI12-M-K9 WCS 7.0 to Cisco Prime Infrastructure 1.2 Migration
R-PI12-BASE-K9 Prime Infrastructure 1.2 Base License and Software
L-PI12-LF-500-LIC Prime Infrastructure 1.2 - Lifecycle - 500 Device Lic PAK
L-PILMS42-500-M Prime Infrastructure LMS 4.2 - 500 Device Upgrade Lic
I have a virtual LMS appliance running where I installed the 500 device license I mentioned. I've actually never used LMS but that's a different story...
As I'm running low on PI device licenses (lifecycle licenses to be precise), the question is:
Is there an officially supported scenario to migrate these 500 LMS 4.2 licenses (that are already the result of a license upgrade) to PI 2.0?
If so: what part numbers do I need to purchase? I suppose I need
R-L-PI2X-U-K9 LMS to Cisco Prime Infrastructure 2.x Upgrade
plus
(L-L-PI2X-500-U LMS to Cisco Prime Infrastructure 2.x Lifecycle Upgrade 500 Device)
XOR
(L-L-PI2X-500-UP LMS to Cisco Prime Infrastructure 2.x Lifecycle Upgrade with PASS 500 Device)
Maybe someone can comment on that... thanks in advance.

In case anyone is facing the same issue:
Meanwhile, I finished the upgrade process using the following part numbers:

Cisco Prime LMS appliance Compatibilty with Cisco Prime NCS

Hi,
Is it possible if we can install Cisco Prime LMS 4.2 in the appliance which is inbuilt with Cisco Prime NCS .
We have PILMS42-1.5K-U license available with us.
Rgds,
Kamal

One can install either LMS 4.2 or NCS on the a physical (software on PRIME-NCS-APL-K9 hardware) or virtual appliance (software installed on customer-provided VM).
The two products (NCS and LMS) cannot coexist on a given appliance instance. This is due to change in the future as LMS and NCS merge under the Cisco Prime Infrastructure 2.0 release but for now they are distinct and separate products with a common approach and similar look and feel but requiring separate servers, whether physical or virtual.
Please refer to the ordering and licensing guide here.

Device discovery in Cisco Prime LMS 4.1

Hi,
im using CISCO PRIME LMS 4.1 for manage my network, i ran a device discovery job using a ping sweep on the ip ranges of my network, ie 192.168.1.0/24, 192.168.2.0/24 and so on... the discovery found all my devices, but it discovered duplicate devices with illegal ip Addresses, ie
ip                                    device
192.168.1.255               S1
192.168.2.0                    S1
192.168.2.1                    S1 (the real address)
all in reachable status.
i dont undestad why the program adds that repeated illegal addresses.. someone can help me with that issue??
how can i run the device discovery to avoid this problem?
Many Thanks.

Julio,
Don't let LMS decide on what IP address it will manage the device.
For example, let LMS do a lookup of the sysname in DNS, then it will use the IP address coming back from the DNS as management IP.
This is what I do to avoid this.
But I also feel that LMS should be bright enough to never manage the same device twice. I think Campus DFM or RME will eventually figure out the 2 devices are the same, but they can't "fix" what is wrong in the DCR.
Cheers,
Michel

Prime LMS 4.2.1 Netconfig and Template TFTP/SSH issue

Similar Messages

Maybe you are looking for