Print size mismatch between Photoshop and printer

I am using Photoshop CC on a Mac Maverick and now Yosemite and have a problem in that Photoshop print settings does not match the paper size I have selected. Photoshop has 15.722 in x 20.361 in while I have 8.5 x 11in selected. If I select a different printer the results are the same. If I save as a PDF and print from preview it prints fine. Any thoughts?

I have since figured this out... you have to drag the composition over from Pr to Ae as illustrated here: (It then becomes "dynamic" )
http://i216.photobucket.com/albums/cc53/zymurgy_bucket/dont-loose-film-fx-after-effects_zp s33d22a32.jpg

Similar Messages

  • Colors are mismatched between photo and printed output. The printed output's tones are off.

    This is an HP Photosmart Plus B210A printer.
    I have almost-new print cartridges installed (correctly).
    I have done a print quality test and the test page seems to be very good.
    The paper I'm using is high-quality photo print paper.
    I'm using quality setting of 'best'.
    Thanks in advance for any advice.
    This question was solved.
    View Solution.

    If it is not a hardware issue, then go into the printers folder, right click on your printer, then select properties. Select the color management tab, you can adjust colors from there.
    This document below would apply to  the hardware end of it:
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02142902&cc=us&dlc=en&lc=en&product=4021935&tmp...
    007OHMSS
    I was a support engineer for HP.
    If the advice resolved the situation, please mark it as a solution. Thank you.

  • Size mismatch between composition and imported vide clip :-(

    Hi from 21 degrees C york UK
    This link illustrates my problem:http://i216.photobucket.com/albums/cc53/zymurgy_bucket/misfit-video-clip-langleys-glitch_z pseec728d8.jpg
    Somehow my After effects comp is hugely bigget than my video clip, I'm so confused tghis hasnt happened to me before & my head is spinning. Basicall the final out put is for YouTube but I just cannot get the After ex composition to scale down to fit the size of the YOUTUBE clip :-(
    Any help very very appreciated!
    Grazie,
    David

    I have since figured this out... you have to drag the composition over from Pr to Ae as illustrated here: (It then becomes "dynamic" )
    http://i216.photobucket.com/albums/cc53/zymurgy_bucket/dont-loose-film-fx-after-effects_zp s33d22a32.jpg

  • When I download pictures from my camera they use to also downloan in Cannon's Easy Photo. In my new computer they don't. I want them to. How???  Also how do i edit photos in Photoshop and print 4 to a page?

    When I download pictures from my camera they use to also downloan in Cannon's Easy Photo. In my new computer they don't. I want them to. How???  Also how do i edit photos in Photoshop and print 4 to a page?

    Please study this, then come back with more specific questions
    Learn Photoshop Elements 12 | Adobe TV
    Learn Photoshop Elements | Adobe TV
    Use of the tools is pretty much the same in all versions of the program.
    "Edit" is a menu item in Photoshop Elements Editor. Don't you see this?

  • Font sizes between  Photoshop and Edge - Any Accurate conversion table?

    I have been trying to make sense of the font sizes between  Photoshop and Edge. It seems that the conversion tables I have found do not actually give the right numbers and I am wondering if there is a table from Adobe that would make it easy to have the right size rather than an approximation.
    I prefer to use text in Edge rather than Photoshop for many different reasons one being dynamic text.
    For example a font in Photoshop in a 780 x 475 image is 8pt - In Edge, according to conversion tables it should be 11 px but it is totally wrong. It needs to be closer to 30 px to be about the same.
    So, Adobe Team, any documentation on that?

    By the way, I have to correct the numbers but they still do not make too much sense. The artist gave me a 300 dpi file so of course the px size what wrong. After converting the file to 72 dpi, the font size happens to be 33.33 pt or 40 px which is now way too big in Edge.  It looks like the size my just be the same 33.33 pt would be 33.33 px. Is this correct?

  • Encrypting network between computer and printer

    I would like to encrypt a network between computer and printer but I see references to ASCII and hexadecimal which I don't understand. Please can anyone explain in simple terms how to go about this?

    The picture you showed is the settings for a WiFi network. There are four main types of encryption 40bit WEP, 128bit WEP, and WPA or WPA2. (I am ignoring WPA2 Enterprise as it is unlikely the printer is capable of this.)
    WEP and WPA and WPA2 have all been cracked although it is still the case that WPA2 is better than WPA which in turn is better than WEP. On that basis while using eny of these encryption schemes is better than nothing if you are really concerned with security you would be better using an Ethernet cable.
    WPA2 Enterprise is still somewhat secure but as its name suggests is not general suitable for home or small office setups.
    With regards to ASCII and Hex, WEP passwords can be entered in either style, they would in fact be the same just entered differently. It is possible to convert an ASCII value to Hex and vice-versa.

  • Is there a difference between AirPrint and printing via usb printer plugged into an airport extreme?

    My printer does not show up in the add a printer option on my iMac when plugged into the extreme. I have a HP officejet 5610 All-in-One. I want to be able to print wirelessly using my Airport Extreme.  Thank you

    Is there a difference between AirPrint and printing via usb printer plugged into an AirPort Exreme?
    Big difference. 
    AirPrint for one will not work via USB, so you will not be able to print from an iOS device like an iPhone or iPad using this type of connection unless you look at additional software....that may or may not allow this option.
    Assuming that you get the All-in-One setup using the USB port on the AirPort.......only printing is supported.
    You will not be able to use any other advanced features like maintenance, scan, copy, fax, etc when the device is connected to the USB port on an AirPort.
    If you plan to use the HP for other things, I would strongly recommend that you connect it to your computer.
    My printer does not show up in the add a printer option on my iMac when plugged into the extreme.
    This usually indicates that your printer model is not supported. Check with HP Support to see if they have any updated Macintosh drivers for the 5610 that you could download and install that might allow this.
    HP Officejet 5610 All-in-One Printer Drivers - Hewlett Packard

  • Color mismatch between CS4 and Canon PIXMA PRO6500

    Hi there! I am trying to research if anyone else is having a problem with color mismatch between CS4 and their printer. Last night I printed a .tiff image out of CS4 to my Canon PRO6500 printer and the sky came out purple / pink! It was supposed to be a stormy grey color. I have the color management turned off on the printer settings. I have CS4 manages color turned on and the correct ICC profile selected for the paper I am using. When I do a soft proof in CS4 the image looks fine, but when I print I get something completely different, mostly with the sky (purple / pink) color! Just for the heck of it I did a Print Preview under my Page Setup and guess what, the sky actually shows purple / pink! So I have no idea what's going on. I checked all my setting, ink cartridges, tried different paper with the appropriate ICC profile and no dice. Still have a goofy looking sky! I thought PROOFING the image is supposed to show you how the printed image is going to look? apparently it doesn't because it's not. The Print Preview has an accurate representation of the print but I have no idea where the pink / purple sky is coming from. They are supposed to be stormy clouds as I said. I appreciate any help anyone can provide .
    Sabciu

    I have the color management turned off on the printer settings.
    But do you have a measured color profile based on a sample print? Most likely not, so this is not doing anything in your favor. The current profile may present the defaults for a given printer, but not the actual density based on your other printer settings. So by all means, unless you can be sure to obey a full calibration throughout, turn on the printer CM. Also, since it is a Pro model, you may actualyl have to use the dedicated RIP software that was bundled with it to get correct results, not the default windows print engine.
    Mylenium

  • Slow swapping between Photoshop and Illustrator

    I have had this issue for a while now where it takes forever to swap between photoshop and illustrator, even if nothing is on my clipboard.  It also seems like it takes forever for photoshop to display its UI no matter what program I am working in prior to clicking on it on the task bar.  Once I am in the programs, they run fine until I try to save or print, at which point to slow to a crawl again.  It wasn't  always like this, but I had to do a system restore a couple of weeks ago to fix a bad boot file, and now the programs run like crap.  I have noticed that the person who worked here prior to me never uninstalled the previous versions of Design Standard.  So I am just tyring to figure out a way to speed things up because this should not be going this slow.
    My computer specs
    Windows XP Professional
    2.83ghz Quad Core Intel Processor
    4GB RAM (tech  under since XP pro only supports 3.3)
    GeForce 9800 512MB Vid card
    All my drivers have been updated and I did a registry cleaner which did not fix the problem.  So any help would be greatly appreciated!
    Thanks

    Imo, you should establish a rather strict
    color management strategy (examples):
    1. Define in Photoshop:
    RGB: AdobeRGB(98)
    CMYK: ISOCoated
    Gray: Black Ink ISO Coated (Custom profile)
    Spot: Black Ink ISO Coated
    2. Distribute this profile set by Bridge
    3. Convert RGB images in Photoshop to CMYK
    4. Define Color space in Illustrator as CMYK
    5. Open the Photoshop file or the Tiff file in
    Illustrator: here it looks as expected.
    Problems: the CMYK file contains an ICC-profile
    which is different to the global CMYK-definition.
    Now it depends on the CMS strategies, and that's
    the point where I'm usually giving up.
    Best regards --Gernot Hoffmann

  • Contrast mismatch between Organizer and Editor

    I can edit an image in Editor to where it looks great, to include the contrast, brightness, shadows, etc.  When I send it back to the Organizer, it look much too contrasty and dark.  When I use the same images in a slideshow originating in Organizer, they still look too contrasty.  Is there a way to correct this?  I'm using PSE 10 on a Windows 7 -64 bit machine. Thanks for any ideas.

    Thanks for your quick response.  I just checked out the settings in both the Editor and Organizer and they're both set on "let me decide".  I'm not sure what to do on that one.  I could go with optimizing the computer screen with sRGB, or the Adobe RGB for the printer, or no management, or decide on the fly.  If I go with the computer, I guess I'd have to change it when I print a photo out, and vice versa.  Have any suggestions for me? Thanks again. 
    New update.  I have a Dell color laser printer, and I just checked the manual.  It offers both sRGB and AdobeRGB.  My priority is really to have a good printout.   If I check sRGB I should be safe for either print or computer, but I'm wondering if I'd get as good a printout with sRGB as with AdobeRGB.  The easiest might be to see what the printer is curently set on, and then set PSE Organizer and Editor to match it.  I'll do that, and then see if that helps the mismatch between Organizer and Editor. 

  • Dynamic link between Photoshop and Flash Catalyst does not exist

    Hi,
    I'm a french developer and I have a question.
    I didnt find any Dynamci link between Photoshop and Flash Catalyst.
    Let me explain :
    I have a photoshop file (.psd) and I import it into Flash Catalyst.
    But I have some modification to do on my design file (psd) but the design does not update himself in Flash Catalyst .
    Do you plane to add the possibility ?
    Thanks a lot !
    Clement
    http://www.dator.fr

    Given that you named the class TextDynamicLayout, it implies you are trying to handle wordwrapping text.  That requires handing down the VBox's explicitWidth to the Text controls before they get measured.  Wordwrapping text can be any size so it needs to have its width fixed in order to determine its height.
    The List classes do not support percentages on the renderers.  All renderers are effectively given a size based on the List's size (or DG Column size).  You can see how explicitWidth is handled in the default renderer by looking at the source for ListItemRenderer.as.
    Note that VBox or any container makes for heavy and slow rendering.  That's why the default Flex renderers extend UIComponent and have custom measure() and updateDisplayList() methods.
    Alex Harui
    Flex SDK Developer
    Adobe Systems Inc.
    Blog: http://blogs.adobe.com/aharui

  • Can't get Camera Raw widow to open between Photoshop and Bridge.

    Okay, so I can't get the Camera Raw editing window to open between Photoshop and Bridge on my new computer. I used Migration Assist and synced up all files from my old computer, and the Camera Raw setting still works fine on my old Laptop. And even images that I edited/adjusted in Camera raw, they automatically pop up in Camera Raw on my new computer, but images that have not been openned in Camera Raw before, don't automaticlly open in Camera Raw editing window?
    How do I fix this so that all images open through Camera Raw window before in Photoshop??

    What kind of file format, raw or JPEG? If JPEG then you'll need to set your Camera Raw Preferences correctly to have JPEGs open in Camera Raw.

  • How can I better improve the color of images between Photoshop and Premiere?

    I have trouble getting true colors between Photoshop and Premiere CS6.
    What can I do to solve this situation?

    Premiere Pro works internally with colors in an RGB (red, green, blue) color space. If you want to edit video clips you create in Photoshop in Premiere Pro, create the clips in RGB.
    If you want to broadcast the final movie it is best to ensure, in Photoshop, that the colors in your image are broadcast-safe. Assign the appropriate destination color space—for example, SDTV (Rec. 601)—to the document in Photoshop.
    You can refer to some suggestion as below:
    http://help.adobe.com/en_US/premierepro/cs/using/WS6693F22C-C06E-431a-A634-62343C65BA7B.ht ml#WS4AF3A4A1-D276-4f3b-A5B2-D3C19D3269DA
    Let me know if you have any more questions on this.
    Cheers!
    Mandhir

  • My Epson photo 1280 will only print 1/2 of a page from a document in Pages program. First print was fine. Have printed out a Mac templet and printer does same thing. Cleaned heads, checked nozzels etc. Any ideas?

    My Epson photo 1280 will only print 1/2 of a page from a document in Pages program. First print was fine. Have printed out a Mac templet and printer does same thing. Cleaned heads, checked nozzels etc. Any ideas?

    Hello, I have exactly the same problem. I could have written the same text. And I have'nt found solutions. Except, perhaps, change this printer (and quit HP?).
    Any suggestions would be really much appreciated.
    Thank you for your possible responses.

  • Mismatch between availability and marker

    I have run the following command:
    /repvfy -detail -fix -pwd password
    and am seeing a section called "Mismatch between availabiltiy and marker". What does this mean? I know there is a bug out from Note: 735957 against 10.2.04 and that patch 6951116 is available. I also know this bug is fixed in 10.2.0.5. But I don't know what exactly this section is telling me. Here is the output I am seeing:
    6. Mismatches between availability and marker
    TARGET_GUID TARGET_NAME TARGET_TYPE MARKER_AVAIL_STATUS MARKER_TIME CURRENT_STATUS START_TIME
    9CB8EE19415C3C6B55954BF3346C1106 ssan-Internal Concurrent Manager oracle_apps_icm 6 09-JUN-2009 10:41:50 1 28-MAY-2009 14:25:22
    1B21AAEF5AC63DD44FE339B7852EA1EE ssan-Report Server_ssan_devstar2 oracle_apps_reports 6 09-JUN-2009 10:41:50 1 28-MAY-2009 14:25:13
    F5EAD749526EC1116A70157771E3D011 ssan-Oracle Workflow Agent Listener oracle_apps_wfalsnr 6 09-JUN-2009 10:41:50 1 28-MAY-2009 14:25:29
    CD32714673BC508CDBF85BF191A5A1B7 ssan-Workflow Background Engine oracle_apps_wfbg 6 09-JUN-2009 10:41:50 1 28-MAY-2009 14:25:26
    FADA1D6BF4DFD0E8AA1739A6666BA210 SSAN oracle_database 6 09-JUN-2009 10:41:50 1 28-MAY-2009 14:25:40
    0BE2ACE2EDC7271744DA1A249E30C9A5 APPS_ssan oracle_listener 6 09-JUN-2009 10:41:50 1 28-MAY-2009 14:25:12
    89D241EEEF24821E30AD66741BC3D433 devstar2.rtd-denver.com oracle_listener 6 09-JUN-2009 10:41:50 1 28-MAY-2009 14:25:20
    F40BAF501645A5957A498E7A270AEA47 ssan-Apps Listener_ssan_devstar2 oracle_listener 6 09-JUN-2009 10:41:50 1 28-MAY-2009 14:25:28
    8 rows selected.

    Various provision like Freight, transport etc .
    these should go to separate GL accounts. if you give wrong account assignment value will be passed to GRIR. then difference will happen
    sunoj

Maybe you are looking for