Print with no borders on 8500 A910

How do we adjust the HP OfficeJet Pro 8500 A910 to print with no borders?

Hello @JASETeam and welcome to the HP Forums!
I'd like to help you print borderless with your OJ 8500A, I just need to get a bit more information
What operating system is on your computer?
What program are you trying to print from?
Are you printing on regular paper or photo paper?
Once I have that I will do my best to get you step by step instructions!
In support of Movember
Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
**MissTeriLynn**
I work on behalf of HP

Similar Messages

Trying to print 4x6 photos. How can I print with no borders on LR5 with my HP OfficeJet 7410? Even when in Print mode in LR5, my photos show a border. Page Setup shows "borderless". Image Settings show "zoom to fill". But cannot print, nor even previe

Trying to print 4x6 photos. How can I print with no borders on LR5 with my HP OfficeJet 7410? Even when in Print mode in LR5, my photos show a border. Page Setup shows "borderless". Image Settings show "zoom to fill". But cannot print, nor even preview, without borders.

JimHess~ Many thanks. In my short history with LR, it's amazing how many people I've seen ask this question. I'm nearly embarrassed at how simple the fix was, but grateful that you didn't dismiss such a basic question. You made my week. And my friend's photo album...

Printing with HP Officejet Pro 8500 A909n Series Printer & Apple Air Print

I am trying to use my IPad and print from it through Air Print.
Has anyone had any success in printing from an IPad, using the latest Apple IPad operating system (iOS 4.2) to an HP Officejet Pro 8500 A909n Series Printer?
The documentation from Apple indicates compatibility with:
HP Officejet Pro 8500A e-AiO HP Officejet Pro 8500A Plus e-AiO HP Officejet Pro 8500A Premium e-AiO
Will the 8500 A909n work?
Thanks.

Hi,
Airprint is not supported for HP Officejet Pro 8500 A909m Series.
Thank you.
I am an HP employee
**** Please mark the post that solves your problem as "Accepted Solution" ****

Trouble Printing with HP Officejet Pro 8500

Hello - I recently changed my laptop and have a Windows 7. I went online and downloaded the software and am able to do a test print page with the Print Doctor. However, when i print from my laptop and select the correct printer, it doesn't do anything or respond with printing. I was able to install and have it work with my old laptop, i just can't seem to work it on this one.
Thank You

Hi @Vanessasood,
Thank you for visiting the HP Support Forums! I understand you are having trouble printing to your HP Officejet Pro 8500 with your computer running the Windows 7 Operating system. I would love to get you up and running but require a little more information:
1. What is the Exact model of HP OJ 8500 you are using as there a few in the series?
2. Did you recently upgrade to Windows 7?
3. How is the printer connected, USB or Wireless?
4. Do you get any error message when you attempt to print?
Click here to download and run the Print and Scan Doctor > www.hp.com/go/tools- It was designed by HP to provide users with the troubleshooting and problem solving features needed to resolve many common problems experienced with HP print and scan products connected to Windows-based computers.
Please let me know what the PSDR finds, I will watch for your reply.
Thanks,
HevnLgh
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

How do I set up to print with an HP Officejett 8500?

How do I get my wireless HP Office Jet 8500 to work with my iPad2?

not all of that models support airprint
http://h30434.www3.hp.com/t5/ePrint-Print-Apps-Mobile/Airprint-on-HP-officejet-P ro-8500-A909G/td-p/391421

Connection Problem HP Officejet Pro 8500 A910

Dear Forum,
we are experiencing connection problems with the Officejet Pro 8500 A910 Printer/Scanner.
The device is connected via Wireless Network and can reach the server (e.g. for storing scanned images).
When we try to access the printer (or scanner) with a Computer (WinPC or Mac) that is also connected via the same Wireless Network, the printer/scanner cannot be reached (host unreachable), i.e. even a simple PING to the network address (IP V4) of the printer/scanner cannot be completed. As soon as we connect the computer via wired LAN, the printer/scanner can be reached again (normal operation). Between both states (computer connected via Wireless Network or Wired LAN) no changes were made to the configuration of the printer/scanner. It simply is unreachable when the computer trying to connect to the printer/scanner is connected via Wireless Network.
We have looked at different firewall settings of the Wireless Router but did not find anything, the firewall is deactivated (as the router operates behind a firewall, as does the whole LAN).
I already switched on the "compatibility to 802.11b/g" in the advanced network settings of the printer, no effect.
Anyone got a smart idea why this is so? We tried with different computers and different operating systems, but always the same picture...
Thanks!
This question was solved.
View Solution.

Reset the printing system:
- Go to System Preferences > Print & Scan
- Right (or control) click in the rectangle listing your printers and select Reset Printing System.
WARNING - this will delete ALL of your printers!
- Select the plus sign to re-add a printer. Select the Defualt tab on the top of the window. Look for the printer, select it and wait until the "Add" button becomes available. Click it.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Print with lr5 vs lr3

Recently upgraded to lr5, now when I print a custom package it prints unwanted borders and cut of portions of images.
Printing in lr5 to Canon Pro9000 MarkII, custom package using 8.5x11 paper with 5 different size cells. Each cell is adjacent to outside edge. Paper is set up to print borderless via "Print Settings and Page Setup" and 0 margins in lr. When print is complete there is about an 1/8 inch border all around entire 8.5x11 sheet and the images are significantly chopped.
FYI no borders show when looking at the print view/module in lr and the edges of the sheet show 8.5x11 in accordance to ruler/guides.
When I perform the exact same print with exact same settings and images in lr3 it prints with no border and no cutting of images.
Any ideas???

Sorry for the late response. I have not yet tried a new driver from canon, but I will as soon as I get a chance. I am a little sceptic about it being a canon driver issue as I believe the drivers are written to work properly with OS releases and not necessarily 3rd party software applications such as lightroom, and like I said lr3 works just fine today with the current driver.
Just to be clear I agree with Rikk that it appears that lr5 is having issues telling the canon driver how it wants the image printed on borderless paper which obviously seams likely that it could be a driver issue. So it would be silly for me not to try reinstalling a fresh driver straight from canons site.
Work Around... Currently to combat this issue this is what I am doing. I set the page to be 8.5x11 with ".12" margins (not borderless) then I set up my cells and place them as far against the edge of the borders (that lightroom is showing on screen) so that I can get the images to fit and arranged properly then print. This works flawlessly (when printing with a bordered paper setup), all images print in cells with no obvious cropping.
Another approach that I could us as a work around is to use lr3 but hey I paid for lr5 so this will work for now, unless I can determine the cause.
I will update this post if I get a chance to reinstall driver.

Trying to print without white borders

Hello. I have the canon pixima mg 2900 printer im i have 4x6 paper but everytime i try print a picture its prints with white borders. I want to print a full picture with no white borders

I was adjusting the opacity through the effects window/tools....
This is the screen shot from INDESIGN file and how the file is set up..... the effect opacity level was set at 85%
This is how the the hi-res pdf was exporting from InDesign and I have all attributes check and nothing is set to overprint....
and this is what the pdf SHOULD look like.....
****and I had to sit there and mess with this pdf FOREVER.... and how I was finally able to export the pdf properly was by using a different PDF export option...
The printer I use has a set profile that I am suppose to use for the pdfing of the final hi-res pdfs to be uploaded to the press....
But when I went and used the pdf-x-1a option it was fine.
Does any one know which setting in the pdf profile that would have affected the opacity to not carry over???
I am going to email the printer directly to see what they have to say and possibly suggest making the correct adjustments so this does not happen in the future....

Can't setup scan to email with google apps for your domain (HP Officejet Pro 8500 A910 Printer)

Printer HP Officejet Pro 8500 A910
Web interface (HPLIP installed on ubuntu 11.10, but problem is linked to web config.)
"The device could not send the test e-mail message. (EmailAccounts-timeout)" when going through the full setup, and "The device could not send the test e-mail message." when testing the account after creating it from the "Outgoing Email Profiles" tab.
No changes.
I can't cofigure the printer to send emails out using the email adress we have created exclusively for it with our domain name in Google Apps for your domain. The settings test ok for the email alerts.
I'm using these settings:
Server: smtp.google.com
Port: 587 (also tried 465)
username: [email protected]
good password, copied and pasted to make sure there are no typo's.

Welcome to the forums Joanda!
I saw your post about the issues you are having with scanning and would like to help!
Please let me know which model of printer you have:
HP Officejet Pro 8500A e-All-in-One Printer - A910a
HP Officejet Pro 8500A Plus e-All-in-One Printer - A910g
HP Officejet Pro 8500A Premium e-All-in-One Printer - A910n
Also let me know which operating system you are running on your computer.
Thank you!
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Printer problems with Officejet Pro 8500 A910

Dear all,
I have been given as a present an Officejet Pro 8500 A910 (serie number CN16LDM020 and product number CM756A). The people whom I have got it from already had some problems with the printer heads. I have accepted the printer, because I want to have it working again. I do encounter some problems however. I hope you kind people on the forum can help me out and get this thing working again. As a side note: I am only interested in using the scanner, printer (only black and white - I do not print in colour) and e-printing (I understand that it is possible to email documents to printer, so that they are printed whilst you are somewhere else).
Upon installation I have conneted the internet to my wi-fi. Upon installation it made some test prints, whereby the black dots were good, but the cyan and other colours were not. When I now turn off the installed printer and switch it on again it takes the printer about 5 - 7 minutes to initialize. On the touch screen of the printer it is said "Checking printer, this might take 5 minutes", "Checking printheads", "Aligning printheads" and alike notifications. After 5 - 7 minutes the printer gives the following notification: " Failure notice. Alignment failed. Refer to device documentation for details." When I then push the question mark on the touch screen the following notidication is given: " Alignment failed. Check printer quality of the current print job. If it is not satisfactory, try aligning the printer to see if that improves the quality. To align the printhead again, touch (home), touch (arrow right), touch Tools, and then touch Align Printhead." When I follow these instructions, the same thing happens. I have tried the option "Clean printheads" under "Tools". The test prints that come out are again good in black and white and not good in colour.
The ink level of the cartridges is very low for Yellow, Magenta and Cyan. For Black the printer gives a question mark. The expiry date of the cartridges is in 2015. The information on the Self Test Diagnostic Page (you get when you print a report from checking the ink cartridges) gives the following status:
Printhead status
Printhead health: Good (for both Black/Yellow and Magenta/Cyan)
Serial: 7735960 (Black/Yellow) and 7744345 (Magenta/Cyan)
End of warranty: mid-2013
Accumulated ink usage (ml): Black 99/Yellow 71, Magenta 57/Cyan 58
Refilled supply:
Detected in printhead/printer? For all cartidges "yes".
When I try to print a document from Word on my MacBook (which runs on Mac OS X 10.6.8) and the printer is on stand-by, Word recognizes the printer, starts with the print order but then comes with the notifications "Printer offline" and "Cannot find printer" and postpones the print order. Today I reset the printer and the print job that I had before the reset (which was postponed) came out.
Today, I printed a document whilst the printer was not on stand-by (the touch screen was on home menu) and the print was well (it was only black and white). After the print, the printer also made a print report. Again, the colour was bad, but black ink was good. After that print report, the printer started aligning again. After 5 minutes it gave the above-mentioned failure notice (" Failure notice. Alignment failed. Refer to device documentation for details.").
I would assume that the first thing that I should do is get new cartridges. However, since I only print black and white, can't I just buy the Black Ink and disable the other cartridges? Then, I am thinking of not buying HP cartridges (since the warranty term is already over). What cartridges do you reccomend (price-quality)? If new cartridges are installed (previous owner had same problems with full cartridges) and the problems (with print heads) are not solved, what should I do?
On a second note, I want to use the option of printing online. In other words, give a print order on my Iphone to the printer so that it starts printing at home. How do I set this up? How can I test this?
I would be very obliged with your feedback on the above.
Kind regards,
Onno

Hey Onno,
I see you have several items listed about your Officejet Pro 8500a (A910 series) printer. The main issue that stands out is the print quality issue. I would advise starting here with your printer.
From your information I can see that refill or remanufacture cartridges have been used in this printer at some point. It is possible that the ink from these cartridges have damaged the internal ink system of the printer. If you have performed all the troubleshooting steps for the print quality issue you are experiencing, then the next step is going to be replacing the printheads of the unit.
Troubleshooting Print Quality Issues
The 8500a requires all cartridges be available even if you are simply printing in B&W. If the cartridges are low, then you will have to replace the cartridges as needed. Typically by the design of this printer, however, print quality issues do not follow ink levels in the cartridges as ink is piped to the internal printheads, thus even with empty cartridges there is some ink remaining in the system.
The printheads for the 8500a can be found at most HP certified retailers if you decide to attempt replacing them as a step towards resolving the issue. As to the cartridges, I would advise using genuine HP cartridges as HP ink is designed with HP printers in mind. For information about refilled/remanufactured cartridges please click here.
Hope this helps in getting the print quality issue alleviated,
Jason
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------
I am not an HP employee.

HP OfficeJet Pro 8500 A910 - Unable to get it to copy, receive a fax, scan, or print

Dell Studio
Microsoft Vista .. 64
HP OfficeJet Pro 8500 A910
Up until a week ago, this printer was performing just fine. I am unable to get it to copy, receive a fax, scan, or print.
==============================
Unable to print.
Job in queue. printer screen says "now printing", However, nothing prints.
When I tried to reinstall the drivers, I got ... "Error 0X00000643"
Ran "EndError" scan and fixed any/all problems.
Still ... No Joy. Still .... Unable to print.
Tried printing a "Test Page".
Still No Joy !!
Screen on printer says "Now Printing"
However, nothing happens.
Does anyone have a suggestions?
Thanks In Advance,
EarlLJ

Same problem here. Already got it replaced with a refurb machine three times. Was fine for a while, then it started the same problem again. Any idea, before I toss it out of the window?

HP Officejet Pro 8500 Pro 8500 A910 black will not print, says printhead is OK

I have an HP OfficeJet Pro 8500 A910. It no longer prints black, even with a new toner cartridge. Have followed all procedures recommended to solve problem. Printhead diagnostics says black/yellow printhead is OK. Any suggestions?

Everything seems to move correctly, but just does not print. Occasionally it does print a faded incomplete print out more often in a blue. All carttridges are new HP solutions center does show filled ink in all stations. Using WIN XP. Printer had done well for about 3-4 yrs.

HP Officejet Pro 8500 A910, 2 sections different paper size, prints incorectly

I have an HP Officejet Pro 8500 A910.
My Word document has 2 pages in 2 sections the first page and section is an envelope and the second page is a letter. On the 8500, if I choose to print just the 2nd page (the letter) it uses the envelope paper size and print half the width. Tried Word 2003/2007/2010 same thing.
This prints fine on an BusinessJet pro2230
Brian

Hi monkplayer,
It looks like your problem is solved? There wasn't a problem with the printer itself, just the printer settings on your Mac?
This is good information though. We don't always have detailed solutions for customers that are using Safari, since it is hard to write instructions for the general public with specific steps for each operating system.
Best of luck,
Mary
{I work on HP's behalf}

HP Officejet pro 8500 A910 won't print wirelessly

"An error has occurred. (devInfoPage-503)".
I've had my Officejet pro 8500 A910 for less than 6 months. It was an easy set up and printed and scanned perfectly for at least 2 months. I use a wireless connection from my laptop which is running Windows 7. Then a few months ago I started having problems scanning wirelessly from the printer pad, it would tell me that there was no computer connected. If I went to my laptop and went into the HP Document Manager it would scan the document and save it to my laptop just fine. And I could still print - the laptop had no problem finding the printer.
About a month ago I had a really big print job for work. But I figured this was a sturdy printer and could handle it. Towards the end though the printer would stop printing for no apparent reasoning with the keypad just showing the spooling circle and saying "printing". The only way to get it to actually print was to unplug the computer, delete the print job and start again.
Then for a while I had to do that every time I wanted to print, even after the "big print job" was long over, and still no scanning from the printer (will scan from the laptop).
I've tried several times uninstalling and reinstalling the software. I've checked to make sure the printer is included in the "home network".
Today I reinstalled the software at the Control Panel on my laptop I get the green checkmark meaning the printer is set up and ready to go, but when I try to print a self test page I get this message "An error has occurred. (devInfoPage-503)". Any help in solving this problem would be much appreciated. Thank you so much for your time.

My Office jet has printed fine wirelessly for 6 months but started to not recognise the computer. re starting worked for while but now it will not recognise the computer at all. The computer says Scanner communication cannot be established and the printer says it sees the computer.
Why did it work but now won't?
Thanks,
Billy

HP Officejet Pro 8500 A910 Premium will not fax from computer with Windows 8

My printer worked great on Win XP and I could fax directly from the printer or from the computer. I installed Windows 8 32 bit (I'm running an older system that works fine for everything I use it for -thank you very much), and downloaded the latest greatest HP driver & software for Win 8 32 bit. Everything works perfectly, except faxing from the computer.
If I run the fax test from the printer, the fax test PASSES. If I run the fax test from the computer, the fax test PASSES.
If I put documents in the printer feeder and use the printer fax functions, it faxes beautifully.
It is only when I fax from the computer, the screen pops up with a status of spooling, then the status turns to Cancelled every time.
It always worked on Win XP.
The FAX printer and FAX driver for the FAX printer showed up in Control Panel automatically when I installed the updated drivers/software from HP. All the properties on the FAX printer look good.
I tried a usb connection, and a network ethernet connection, with the same results.
Printing and scanning all work fine. I really like this printer, and I would like it even more if I could figure out how to get it to fax a document from the computer.
When I say fax from the computer, I mean opening a document, saying Print, selecting Fax - HP Officejet Pro 8500 A910, filling in the fax information page, selecting my cover page options, and pressing the send fax. All just like I used to do before I upgraded to Win 8. When I hit send fax, that is when I get the popup that the fax is spooling, then it goes to cancelled. No error codes are displayed, no clues as to why, no nothing. If I print the document and put it in the printer document feeder, I can fax it using the printer display screen no problem.
Very bizarre.
This question was solved.
View Solution.

Alright, I spoke with some of the engineers and they suggested the next few steps. First, here is a thread on an MS forum about removing a driver in an alternate fashion.
http://technet.microsoft.com/en-us/library/cc730875.aspx
Another thing to note is that in Win8 you can easily access the Command Prompt by hitting the windows key and typing “command prompt.”
Additionally, I will PM you some further steps on removing the vestiges of the software from the back-end of your PC. You will HAVE to be sure to follow those instructions to the letter.
Do these two things and let me know what happens after you install the printer again from the direct download link I have already provided above.
Let me know and have a great day!

Print with no borders on 8500 A910

Similar Messages

Maybe you are looking for