Printer cannot print after disabling SNMP

I need to disable SNMP for network security reasons. After doing so from the web configuration page of my P2035N printer, network users cannot print to this printer. It shows as 'offline', even on the web page. We have tried restarting the printer, as well as the print spooler on the server. It is connected via TCP/IP, IPv4.

Working on the assumption that you had an older version of the Canon CAPT driver installed on this Mac before you installed 10.8, I suggest that you open Finder and trash the following files. Note that if you haven't done the reset that Greg has suggested, you will need to open Print & Scan and remove the current LBP6000 printer.
Mac HD > Library > Printers > Canon > CUPSCAPT (trash this entire folder)
Mac HD > Library > LaunchAgents > jp.co.canon.CUPSCAPT.BG.plist
Mac HD > Library > Caches > Canon > CUPSCAPT > CCPD > ccpd.conf
With the above files removed, restart your Mac and then run the CAPT v3.60 installer again. Then add the LBP6000 in Print & Scan and then see if you can print without error.

Similar Messages

I cannot print after updating my MacBook Pro from OSX Tiger 10.4 to OSX Snow Leapord 10.6. Can anyone help me?

I cannot seem to print after updating my MacBook Pro from OSX Tiger 10.4 to OSX Snow Leapord 10.6. Can anyone help me?

Try re-adding your printer in System Preferences/Print & Fax. Not sure what type of printer you have, but if it was old and relying on an Appletalk connection, Snow Leopard dropped that support.

Connect to a network printer for air print, after disconnect from the wifi iphone keep pop up a message saying the printer is offline. How do I disable this annoying message?

Connect to a network printer for air print, after disconnect from the wifi iphone keep pop up a message saying the printer is offline. How do I disable this annoying message?

Hey ronniefai,
Thanks for the question. I understand you are receiving a prompt that your printer is offline. This may be due to a printing job that is currently in the queue. Are you able to see the print summary when following these steps?:
Viewing the Print Summary
You can view the Print Summary by double-tapping the Home button and swiping to the right to reveal Printer Center. Then tap Print Center.
Note: Print Center is available only while printing is in progress.
via AirPrint Basics
http://support.apple.com/kb/HT4356
If so, see if you can cancel the job. If not, what happens when you re-connect to the network that the printer is on?
Thanks,
Matt M.

Ricoh Aficio SP 240DN cannot print after Yosemite installed

Ricoh Aficio SP 240DN cannot print after Yosemite installed

I have this problem too.
I've installed the most recent drivers for these printers and unfortunately it's still not compatible with Yosemite.
I guess all we have to do is wait until Ricoh/Lanier brings out an updated driver for us

Cannot print after downloading os7

cannot print after downloading os7

Hey snagger68,
Thanks for the question. The following article outlines steps for troubleshooting AirPrint:
AirPrint Basics
http://support.apple.com/kb/HT4356
If you are unable to print, or if you see the message "No AirPrint Printers Found"
Verify that the printer:
1. Has power and is turned on. If it has power, turn the printer off and then on again to see if that resolves the issue.
2. Is connected to the same Wi-Fi network as the iOS device.
3. Has the latest firmware version installed.
4. Has paper with enough ink or toner installed.
5. Is free of any errors displayed on the printer's control panel.
If necessary, consult the printer documentation or contact the printer vendor for help with the above steps.
Notes:
- AirPrint printers connected to the USB port of the Apple AirPort Base Station or Time Capsules are not supported with AirPrint.
- Some Wi-Fi AirPrint printers can take several minutes to join a Wi-Fi network after being turned on. Ensure that the AirPrint printer is connected to the Wi-Fi network before attempting to print.
Thanks,
Matt M.

Unable to Print After Installing Adobe Acrobat Reader Upgrades.

. What software version of Abobe Acrobat Reader should be used for an HP PhotoSmart Plus printer? I currently have Adobe version 9.3 installed. I receive pop-up notices to install new Adobe Acrobat Reader software upgrades. I have installed the software upgrades and then my HP PhotoSmart Plus printer was unoperational. I deleted the Adobe software upgrades and my HP PhotoSmart Plus printer began to operate. I contacted HP technical support and was told there is no compatibility issues between Adobe Acrobat Reader and HP All-in-One Products. It might be a problem with the specific Adobe software upgrades. HP requested that I contact Adobe support for problem resolution. Has this problem ever happened to you? Any problem resolutions would be appreciated.

Hello there! Welcome to the forums @Oldchev
I understand you cannot print, after installing your Officejet 7410 All in One printer.
Please let me know the following, and I'll do my best to help!
What is the Operating System of the computer?
Have you tested hardware functionality (made copies)?
Have you tried printing from different programs?
Have you tried uninstalling and reinstalling the software?
What Firewalls and Anti-virus software are installed?
Have you tried disabling or uninstalling them?
Best wishes
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Unable to print after updating to yosamite

Like so many I have the same issue after updating to Yosemite. I have tried deleting the printer, updating drivers, resetting the printers, restarting the Macbook Air but all to no avail. Printer is an HP Laserjet 3055 and has worked fine up until now. Come on Apple, this is really frustrating!

Hello there! Welcome to the forums @Oldchev
I understand you cannot print, after installing your Officejet 7410 All in One printer.
Please let me know the following, and I'll do my best to help!
What is the Operating System of the computer?
Have you tested hardware functionality (made copies)?
Have you tried printing from different programs?
Have you tried uninstalling and reinstalling the software?
What Firewalls and Anti-virus software are installed?
Have you tried disabling or uninstalling them?
Best wishes
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Problems with your HP printer after upgrading to Windows 8.1

If you are experiencing problems with your HP printer after upgrading to Windows 8.1 please click on the below link and install the HP Print and Scan Doctor and run the utility to fix the issue.
www.hp.com/go/tools.
I was an HP employee
If I have helped you solve your issue please mark it as solved
**Say Thanks By Clicking on the Kudos Star**

Hi.....my laserjet 1536dnf mfp was working perfectly with win 8 pro....then I installed win 8.1 pro and now the computer ,which is part of a network,can not communicate with the scanner of the printer--it prints just fine. On another computer (running win 7 ) on the same network, the scanner and all other printer functions work just fine.
I have tried installing the latest drivers from HP......scanner still not "communicating" with computer.....also temporarily disabled firewall.....please help...all the best -David G (gossat)

Driver wizard says The drivers of your printer are disabled, but doesn't fix.

OfficeJet 6500 E709a series. Windows 7 64-bit. Printer operates from Word, emails, Copy function. Two programs, Photoshop and Printshop, no longer print when directed to print. Printshop says "Install a printer." Print Shop has tasks in printer queue and won't print. Hp Driver Wizard says,
The current full HP software is already installed for the selected printer but the basic functionality drivers appear to be missing or configured incorrectly. Click Next. After the click: The drivers of your printer are disabled, Click next to enable them.
These responses spool with no further option.
This question was solved.
View Solution.

Hi there mandrelliott,
Try downloading and running the print and scan doctor located here:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03275041&cc=us&dlc=en&lc=en
It can fix a lot on its own and if not give a better idea of what is going on.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

How to Fix Disappearing HP Printer Drivers -- Disable HP CUE Device Discovery Service

I have a new HP G60-530US laptop with Windows 7 installed (less than 2 months old). It is connected to an HP 7410 All-in-One Printer and a Brother laser printer.
Three times now, the HP 7410 printer has mysteriously disappeared from the installed printers. The Brother printer does not disappear.
To re-install the HP 7410 printer requires disabling the AVS using the Services,msc utility (not just shutting down the AVS (Panda in my case)). It takes 20 minutes or so to re-install the HP printer driver software.
HP tech support is clueless about the cause or cure for this.
The laptop people referred me to the printer support people and the printer support people referred me to the laptop support people. The last tech support guy suggested that I restore the system on the theory that if the problem persisted it would be a hardware problem and not a software problem. He seemed to miss the fact that the disappearing printer driver software only occured with HP printers.
HP technical support was worthless.
Some internet forums suggest that this occurs when HP machines are connected to different networks. I noticed my problem occur after I took the laptop on a business trip and connected to a different wireless network.
On Vista forums, I've discovered that the disappearing HP printer drivers has been a problem for some time over a wide range of HP printers.
The solution identified on those forums is to stop and disable the HP CUE Device Discovery Service. Apparently, this service is used to detect HP printers and add them to the HP Solutions Center software.
In my experience, the HP printer drivers disappeared when my laptop comes into range of a "foreign" HP printer with wireless capabilities. For example, my laptop dropped my configured HP wireless printer when I went to an office that had a different wireless HP printer installed. The HP CUE service trashes the existing printer driver even though you do not intend to install and use the "foreign" printer. That would also explain why the printer drivers disappear when visiting a hotel or other location where any HP wireless devices exist. It would also explain why non-HP drivers do not disappear.
I've disabled the CUE Device Detection Service (using the Services utility). I'll see if that works. From what I've read, the CUE Device Detection Service is not needed after you have installed your printer, but it remains in your computer's active memory just "in case" you want to connect to a new HP printer and install software for that printer. Said differently, after your printer is installed, it remains as useless HP software that clogs your machine's resources.
A patch from Microsoft or HP (e.g., a patch that disables the CUE service) would be a big help to users if the number of posts on this issue are any indication of how pervasive this problem is.

This seems to be a common problem that exists for many HP devices, varying computer moakes and models and different operating systems. So, the conclusion must be that it is a HP issue. WHY ARE THEY NOT FIXING IT?
Based on this I am quite happy to buy a different make of printer so how does HP justify the continuing lack of support?
I posted a message about my C7180 All-in-one which had been causing problems but I put it down to me making (unrelated) changes to my system then noticed it got worse when I connected a new Trust digital pad. However, even when the pad is not connected I get the problem of disappearing drivers with the printer still visible.
What seems to happen to my set-up is it works when it is first reloaded and used, but the next time I open the HP software it fails and no other software is able to print/scan on the device.
Can somebody explain what the CUE is? I'll give it a try but I don't know what it refers to.
Who'd have thought that in the 21st century, software/hardware engineeers still can't make a simpy process for a computer. Whatever happened to the promise of plug'n'play?
P.

HP Officejet 6500 can't print after 10.6.6 upgrade

I have a HP Officejet 6500 and can't print after 10.6.6 upgrade. Scan copy and fax are fine. I also cannot get the HP utility to recognize the device. Connected via USB.

Same issue via ethernet.
Can print installing as printer from system preferences, but the HP utility cannot recognize the device.
Message was edited by: Angelo77

Adobe PDF printer and "Start printing after last page is spooled"

Hi,
After calling the Belgian Support for Adobe Product, I'm trying to have some information here.
Hope to get some help.
We use acrobat pro XI on windows 7 client and when we print a test page with the "adobe pdf" print queue on network share, we get a printing error when the "start printing after last page is spooled" is selected in the advanced tab of the printer queue. (document is not generated, and stay in the spooler with an error).
This problem is not present if printed localy or when we use the "start printing immediately" or "print directly to the printer".
The support agent from adobe Belgium told me that the reason is generating adobe pdf on network share is not a supported operation. We have to save the document localy all the time.
Is it really an answer from Adobe ?
Do you have an other explanation ?
Thanks for your help,

Thanks for your very good explanation Dov.
We use Adobe livecycle for this kind of purpose.
The situation described is diffrent, but you completely repond and I will be able to have some element to find a solution.
In fact, I'm implementing a softwate called DeviceLock, used to control connected devices (usb, network, drive). But this software, once installed, change the local printer parameters from "print directly to the printer" to ""start printing after last page is spooled".
As we use redirected folder in our environment and users cannot use local drive (for user's data backup) you will understand the problem.
Of course, we should be able to force the correct settings back, But Devicelock seem to change this settings after policy refresh.
I have contact with Devicelock about this problem of course as their software modify the settings, but was looking for a reason why we were not able to use the "start printing after last page is spooled" parameters with adobe Printer.
Thanks for your explanation,
PS:The driver's dialog won't prevent you from setting “Start printing after last page is spooled” or “Print directly to the printer” but setting either of those options will cause the operations to fail as you note.
note that only "Start printing after last page is spooled" cause an error and this, only for network share location. The "print directly to the printer" or the "start printing immediately" work fine either on a local drive and a network share

Restrict Output type at the time of Picking and Print after PGI

Hi All....
My business requirement is to restirct certain Output types such as LD00, LD0F etc. at the time of Picking and Batch determination and to print after PGI.
These output types are triggered Automatically via Batch job scheduled via third party tool. All the complete Delivery process is Auto.
Once Sales order is created the below process takes place.
Auto Delivery
Auto Shipment
Auto Picking and Batch determination (Now in this step I need to restrict)
PGI (Manually vai some custom program)
Once the Picking is done all the Output types appear in Delivery Header output which are processed with a Dispatch time of 4. (Appeared as Green tarrif.)
For the Output type LD00 -> 911 routine is added .
This routine is triggering at the time of Picking and Batch determination.
At this Point of Picking I can restirct the output type by using the Routine that not to display in Delivery Header, but iam not able to retrieve again at the time of PGI. Is there any option to get the data of Output type at the time of PGI.
Or is there any option for LD00 output type to dynamically select the Routine Number to trigger at the time of PGI. ( If I use Routine no 1 it will trigger at the time of PGI, but I cannot change especially for this purpose since this output type is used for multiple purposes)
Pls provide me the solution.

Hi Brad
I can copy the code from routine #1 into my routine #911 inorder to restirct the display of output type in delivery header. But as mentioned by you this routine is not triggered at the time of PGI. ( I checked at the time of PGI )
If i link my output type LD00 with Requirement #1 routine then it will be triggered at the time of PGI, but here the o/p is linked with Requirement #911.
Pls let me know if any thing wrong i mentioned...

Hp photosmart premium wireless C309 can't print after updating to IE 9 and i think java script

hp photosmart premium wireless C309 can't print after updating to IE 9 and i think java script. I am a realtor working from home and inorder to use the forms it required I update to IE9 and I think java, this is the link. http://www.car.org/tools/zipform6/ After doing so my printer does not work. I tried to go on line and reinstall from a link on line but it did not work. I don't know what to delete and what to add and how to get the " HP sSolution center" to work again. the printer was already poor performance from day one. Always having to unplug and restart and the black ink always runs out too quick. but right now my concern is just being able to print and scan. I am in the middle of a deal and can not communicate with all parties effectively. please help

What error messages are you getting?
What OS are you using?
How is the printer connected to the computer?
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

HP LaserJet 1320 requires user intervention to print after Leopard

Ever since upgrading to Leopard, almost every single time I send a print job to my HP LaserJet 1320 (over the network, it actually connected to a PowerMac G5 in my office), it triggers an error warning (orange flashing light) on the printer. Pressing the main green print button lets the job print, but this is really annoying.
I checked and Apple recently posted a note about the HP LaserJet 1200 having a very similar problem except that an error page was printed after each job. The workaround they suggest for this doesn't work with the LaserJet 1320 problem, however.
A quick Google reveals at least one other Leopard using HP LaserJet 1320 owner is seeing a similar issue. And actually, as I composed this post, I found some 1320 owners in another Apple Discussion post about HP printer issues with Leopard. They suggested using the generic PostScript driver, but then I really like to have the ability to duplex.
Nothing in the /private/var/log/cups/error_log file of note as far as I can tell.
Any ideas? Any other people out there experiencing this problem who might have a solution (other than switching to a generic postscript driver)?

Ok, I think I've figured a way to make the laserjet 1320 stop requiring "user intervention" (e.g. pressing the green button for every printjob).
Try the following:
Open "System Preferences" -> Choose "Print & Fax" -> Choose the Laserjet 1320 printer -> Press button "Options and Supplies..." -> Select Driver "tab" -> In the drop-down-menu "Fit to page" choose "Nearest Size and Scale" instead of "Prompt User".
The chosen driver should be "HP Laserjet 1320 series", because the generic postscript printerdriver dosen't have the duplex option amongst other shortcomings.
I find it odd that the lowest memory-option is 16-31mb of ram. The default configuration of 16mb is not IN that range, but maybe that is a little too nitty-gritty.
~ Jørgen

Printer cannot print after disabling SNMP

Similar Messages

Maybe you are looking for