Printer hp6500A e710: wireless doesnt work

i wanted a wireless printer, but i cant find it at the printer. Manual says it should be at network / wireless. But at mine, wireless doesnt appear. I have turned router and printer off, it still doesnt appear. Does the network cable need to be removed? Tried that but no difference... I am disappointed now :-(

Hi vivid444,
Welcome to the HP Forums!
For this issue, I would start of by doing a reset of the printing system, and a verify, and repair of the disk permissions. I have included the document 'OS X Mavericks: Reset the printing system'. Before you do add the printer back in, you will need to complete the verify, and repair of the disk permissions.
I have included the document 'Disk Utility 12.x: Repair disk permissions'. This will walk you through the steps to clean up your Mac. Now for step three, please select the hard drive. After the repair of the disk permissions has completed, please restart your Mac.
Once the Mac has restarted, try adding the printer back in.
Are you able to add the printer in successfully?
Looking forward to your reply.
I worked on behalf of HP

Similar Messages

  • Fasincate/Galaxy S Wireless Doesnt work

    We have two Fasicnate/Galaxy S phones and the wireless doesnt work on either. I understand this is a bug. Any suggestions short of going to Verizon..?

    I have listed some information below that may help with the wireless issue you are experiencing.
     **These steps would be assuming it is your home’s Wifi network that you cannot connect too.
    Step 1 – Ensure you have sufficient battery power.
    Step. 2- Ensure WiFi is disabled. (instruction below)
    http://support.vzw.com/clc/devices/knowledge_base.html?id=35250
    Step. 3 – Remove the existing Wifi connection (instruction below)
    http://support.vzw.com/clc/devices/knowledge_base.html?id=35425
    Step 4 – Try putting the Wifi connection on a different channel.
    Step 5 –Try changing the encryption of the Wifi network preferably (WPA / WPA2 PSK)
    Step 6 – Set the Wifi connection back up on the device. (instruction below)
    http://support.vzw.com/clc/devices/knowledge_base.html?id=35424
    Step 8 – Ensure Wifi is back on (instruction below)
    http://support.vzw.com/clc/devices/knowledge_base.html?id=35250
    Step. 9 - Try relocating the device. (Something in the immediate location could be affecting the service received)
    Step 10 – Try uninstalling applications that are not native to the device, and could possibility tied into Wifi (e.g. Virus protection, Power/Network control tools, etc.)
    Step. 11 - Soft reset (power off the device, pull the battery out for 20 seconds and place it back in)
    Step 12 – Hard reset. Performing a hard reset will remove ALL data including the Google account, system data, application data, application settings, and downloaded applications. Only perform this reset if the steps above did not correct the issue. (instruction below)
    http://support.vzw.com/clc/devices/knowledge_base.html?id=35372

  • Print easy text.vi doesnt work in executable

    I have 3 target machines running labview 2012 on a PXIe8101controller.  In my statemachine the vi prints out a report using easy text report vi ( on report generation pallet) at the end of the test.  Its an executable vi on all 3 machines.  On 2 of the machines it works fine.  On the 3rd it hangs up when I'm logged in as a standard user.  If I log in as administrator it works fine.  The thing I noticed is that on the 2 machines it works on, the image is "factory..1.2.1f6"  (under control panel>systems).
    On the test equipment that it only works in admin mode the factory image is 1.2.4.f1.  Also MAX is 5.3.1 on the one that runs fine and 5.5.0 f1 on the one that  it doesn't work on.  Anything I'm mssing?
    Thanks.
    Solved!
    Go to Solution.

    Maybe you can enlighten us with your solution so others may benefit.  Unless it was just something silly.  Then just say it was something silly.
    Myself, I'd probably go ahead and post it, even if it was silly little mistake.  At worst, it's a laugh on me - at best, someone else made the same boneheaded mistake I lived through and they don't have to walk in my footsteps. 
    Bill
    (Mid-Level minion.)
    My support system ensures that I don't look totally incompetent.
    Proud to say that I've progressed beyond knowing just enough to be dangerous. I now know enough to know that I have no clue about anything at all.

  • My Time Capsule Wireless stopped working.

    Hi
    so i have the new generation time capsule. I set it up and it was working fine.
    then a couple of days ago...we had a power issue, with low level power. I switched off the unit during this period. Now that the power is back, the capsule wireless doesnt work. When i connect to the ethernet, it works fine. But when i disconnect, the wireless cannot even see the base station.
    what is wrong and how can i fix the wireless?
    kindly help
    thanks
    Joshua

    With the Time Capsule powered on, hold in the reset button on the back of the Time Capsule for 10 seconds and then release. Allow a full minute for the Time Capsule to restart to a slow, blinking amber light.
    Now reconfigure the Time Capsule again, just like you did before. You can use the same device name, wireless network name, password, etc that you used before if you wish.
    Once the Time Capsule restarts, check to see if you can receive a wireless signal from the Time Capsule.
    If you still cannot see a wireless signal, the recent power outage has unfortunately damaged the Time Capsule, and it will need to be replaced.
    It is always a good idea to connect your modem, Time Capsule,, and other devices to a surge protected power strip to help reduce the chances of a component failure in the future.

  • HPM1212nf MFP i can't scan but wireless network works fine for printing

    i have the MFP set up fine for printing over a wireless network.  Any idea on what more i  need to do to get the machine to accept a scan command from the computer using HP Laserjet Scan?

    Hi there @bc123!
    Thanks for contacting the HP Forums!
    I see that your having a communication issue with the HP LaserJet when it comes to scanning to the computer, and I would be happy to provide you with my assistance.
    A good place to start when troubleshooting scanning is to ensure the CD was installed correctly on your computer. If the CD is unavailable then I can provide you with a link to the HP driver download: Drivers & Downloads
    In the link provided you will want to:
    1.enter your printers model number and click GO
    2.select your printer model
    3.select your operating system and click NEXT
    4.Click on Driver - Product Installation Software (‏1)
    5.Click DOWNLOAD next to the full feature software
    To provide you with a more direct link to your software and to better assist you, would you please provide me with the following information:
    1. What operating system version the computer is running (ex. Mac, Windows, etc.).
    Bellow are 2 links I located from HP and Macintosh on how to locate your version of operating system.
    Which Windows operating system am I running?
    Finding the OS X version and build information on your Mac
    2. If the computer is running Windows I will need to know what version (ex. 32-bit or 64-bit). 
    I have provided another link from the HP web site showing you how to check if its 32-bit or 64-bit
    Is the Windows Version on My Computer 32-bit or 64-bit?
    3. Laserjet model number (ex. P1102w, CP1025, etc.).
    Please post back with the requested information, as well as the results of your troubleshooting.
    Let me know if this was helpful!
    Cbert
    I work on behalf of HP.
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" at the bottom of this post to say “Thanks” for helping!

  • How can i get my wireless to work on my printer hp officejet pro 8600

    how can i get my wireless to work on my printer hp officejet pro 8600

    You'll get faster help w/this question by posting it in the Wireless forum...here:
    http://h30434.www3.hp.com/t5/Printer-Networking-and-Wireless/bd-p/Networking
    I am an HP employee.

  • Trouble with getting the wireless to work with HP Laserjet P1102w printer

    Hi really struggling 
    I just bought the HP Laserjet P1102w as it was advised that it would run my apple products (Mac OS 10.6  Snow Leopard laptop and ipad). 
    I have mangaed to set up printer to work using the USB cable to the laptop. Success.
    BUT i am finding it impossible to get it to work with wireless on any devices.
    I get as far as network selection in set up and nothing is in the list (unlike USB which has the printer named) - so i click the 'create' button and input my network/SSID  code , which is a BTHub. I assume this is correct?  Or is it an address to be found elsewhere ?   I have downloaded driver and software (update HP Firmware utility)
     which I believe to be correct from the HP.com website for the operating sytem of the mac. 
    I have also followed a number of videos but often the process does not follow the video sequences. 
    I have tried to speak to PC Word  'know how team' who sold me the printer but they had no knowledge at all to help this situation.   Any help would be much appreciated - this seems l ongoing problem for some other  users. 

    Hi @bgriffiths60 ,
    I understand that you are having issues setting up the printer over the wireless network. I would really like to be able to help you resolve this issue.
    To check your network Encryption type, go to the Apple, System Preferences, Network, click the Advanced button/double click the network name. (shows WEP or WPA)
    To check the network password follow these steps:
    On the Apple menu bar, click Go, select Applications, Utilities, Keychain Access, double click the network name,
    check the box to show the password, type in your Mac password to view it. (some networks have a shortcut password setup)
    Make sure Safari is set as the default browser. Sometimes the Embedded Web Server won't open in other browsers.
    Open Safari, across the top select the Safari menu, select Preferences, General, set as default.
    Restore the printer defaults: Turn the printer off, hold down the wireless button and cancel (x button) while turning the printer back on and don't release the two buttons until the printer stops making noise.
    Print out a configuration report and make sure the SSID and IPv4 address are cleared.
    HP LaserJet Pro P1102 and P1106/P1108 Printer Series - Printing a Configuration Page.
    Go to the Apple, System Preferences, Print and Fax.
    Double click on the P1102w.
    Open the Utility.
    Click Printer Setup.
    Click HTML config.
    This should open the Embedded Web Server for the printer.
    Click the Networking tab.
    Click Wireless from the list on the left.
    Under Communication Mode , click Infrastructure.
    Select your network SSID from the Available Network Names (SSID) list and then click the << button so the network name moves over to other box.
    From the Security Mode pop-up menu under Authentication , click WEP, WPA/WPA2 or open . Your selection depends on which Wireless Security Protocol your network uses.
    Make sure you select either hexadecimal or alpha depending on your password. (very important)
    Apply the settings.
    In the confirmation box (changes have been saved), click OK.
    You should get a solid blue light on the printer shortly.
    Then all we have to do is delete the USB driver and add the network driver.
    Click on the Apple.
    Click System Preferences.
    Click the Print and Fax icon.
    Highlight the printer and click on the - sign to delete the printer. (USB driver)
    Disconnect the USB cable.
    Then click the + sign and select the printer from the list and click add. (P1102w Bonjour)
    Test the printer.
    If you have any issues with the HTML config opening then do the following steps:
    Close any applications.
    On the Apple menu bar, click Go, Computer, MAC harddrive, Library, Printers, HP, LaserJet, click on folder for your printer, click on EWS browser or HTML config, click the Networking tab, click wireless on the left and fill out your information. (make sure infrastructure is selected) Apply settings.
    Then delete the USB driver and add the network printer.
    If there is anything else that I can help you with just let me know.
    Have a nice day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • Can't get wireless to work on J6480 printer

    My new HP Officejet J6480 All-in-one won't print wirelessly.
    I get a message printer is offline.
    With a USB cable hooked up, it will print from my new IMAC.  I have followed the instructions that came with the printer but it won't work yet.  
    I have the Imac set up on airport.
    I have a wireless router for my dsl connection.  I need to print wirelessly not only from my imac but also from a gateway desktop, a dell laptop and a toshiba lap top.
    I have used the HP printer manager.
    I printed from the printer the HP network configuration page and the wireless network test report.  They seem to all be ok.
    Last thing, I have tried to registor online several times but it never goes through 
    This question was solved.
    View Solution.

    Here's a video that steps you through setting up the J6480 on a wireless network with a Mac.
    The video pretty good and I think it will help.
    Regards / Jim B
    Regards / Jim B / Wireless Enthusiasts
    ( While I'm an embedded wireless systems engineer at work, on this forum I do not represent my former employer, Hewlett-Packard, or my current employer, Microsoft )
    + Click the White Kudos star on the left as a way to say "thank you" for helpful posts.

  • HT4356 I am trying to print wirelessly from my ipad to an epson stylus SX438W. The connection appears fine on both devices but the ipad cannot connect to the printer. It has been working fine for the past 4 months. Can anyone help?

    I am trying to print wirelessly from my ipad to an epson stylus SX438W. The connection appears fine on both devices but the ipad cannot connect to the printer. It has been working fine for the past 4 months. Can anyone help?

    Have you tried restarting the printer? Reboot the iPad as well.
    Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.

  • IPad to print Webpage on hp6500a not wireless

    I have an IPAD 2, bought a hp6500a (not wireless) so I could print with IPAD, printer is on my home network. Trying to print from IPAD AirPrint, printer not listed. Can print through hpeprint. I don't want to send an email to print... i.e. I want to print a web page because there is a recipe in the page, if. I email this using HP eprint, it turns into a link. Is there a way to print a Webpage or highlighted piece from a Webpage from my IPAD to my HP6500a. Thanks for your help!

    That information is on this page (scroll down to the "Additional Information" heading):
    http://support.apple.com/kb/HT4356

  • Hp laserjet p1102w: wireless not working: unable to change to new network

    I just moved and established a new wireless network to which I want to connect my printer.
    I have followed instructions on HP's websites.  All goes well until I attempt to open "html config..." on the printer utility screen.  nothing happens after selecting "html config...". 
    printer works fine if connected via usb; doesnt work wirelessly from laptop, iphone or ipad.   I would like to continue to use the laserjet wirelessly.
    any suggestions are appreciated!

    "OK let's try this again.  What is the make and model numbers of all you network equipment?  How is everything connected?  OS of computers?  Please explain."
    Make & model #:
    printer:   hp laserjet p1102w
    cable modem:   arris dg860
    I am printing from a macbookpro (OS X 10.6.8), iphone 5c and an ipad.
    the wireless printing worked just fine from the laptop, my iphone and ipad while at my previous address where I shared a wifi with roommates.  I now have my own wifi via cable (tv) that has a different name than the previous wifi.
    this printer currently only prints via USB. the wireless printing doesnt work from any device. 
    messages:
    laptop:     printer offline
    iphone:   no airprint printers found
    ipad:        no airprint printers found

  • How do i connect my MacBook Air to a Printer on my Wireless Network

    How do i connect my MacBook Air to a Printer on my Wireless Network ? The printer is connected to a PC running Windows 7. That PC is connected to my Wireless Network. MacBook connects fine to Network, but can't find Printer.

    Hi Kappy,
    Thanks for your response. I followed your instructions (for Mac OS 10.6.7). It seemed to set up OK, but when I tried to print I kept getting the following Failure Message "Session Setup failed : NT_Status_Invalid_Parameter".
    When I get the "Advanced Window" should I enter anything into the "Location" field ? Maybe I am not entering the correct Workgroup, Server or Sharename ? Is there a way to make sure all of that is correct ? I went on to the computer that the printer is connected to and verified all of that, but am not sure I looked in the right places.
    When I print via my Home Network from another Windows 7 Computer to the same PC, it works fine. I just can't get it to Print from my MacBook Air.
    I thought of using the IP Address. How do I find the IP address of the Computer that is connected to the Printer ? Is it what they call the IPv4 Address, or the IPv4 Default Gateway ?
    Appreciate any help you can provide.

  • C309a printer not conecting wirelessly- printer's wireless wizard not finding router- rebecca

    new comp.  running windows 7.  i've downloaded driver updates,  cd for printer... HP diagnostic tool etc.  turned every device off including router, modem, and rebooted.  reset router to defaults.  now for some reason printer not finding wireless router in NEW network name wheni  run wireless wizard from printer.  says no link on printer.  on new comp says printer disconnected.  diagnostic tool says incompatible with windows 7. have downloaded updates from HP as of december.  wireless network test says fail under wireless working.  all other comps in house can get on wireless internet. attempted to manually type in routers info... ip address etc... still says no link on printer.  did the routerlogin.com for my netgear router thats 3 years old....for ip's etc...
    i need to get the printer to find the wireless router!!!!!!

    First, let's make sure the printer is OK.  From the front of the printer: Setup > Network > Wireless Network Test.  Does it pass all its tests?
    Next, in the same Network menu, Reset Network Defaults.
    Now, if all that goes well, from the same Network menu run Wireless Setup WIzard.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • How to connect a printer to a wireless connection using airport/time capsule

    How do you connect a Cannon MP620 printer to the wireless network with my time capsule/airport?  It was set up before but I've had to redo all the settings with a new Time Capsule and now the printer isn't working.  Can't remember how I set it up before.  Didn't seem that hard back then.
    Thanks!

    So you plugedd the printer into the time capsule usb right?
    You need to re-add the printer in the system preferences one more time because the location has moved.

  • HP Photoprinter C7280 printer. The wireless radio is on but not functioning - so no wifi conection.

    HP Photoprinter C7280 printer. The wireless radio is on but not functioning  - so am unable to gain wifi connection and print! - Why?   How do I fix, Thanks

    I would guess that the printer's wireless radio has died.  Have you tried plugging the printer into your wireless router with an Ethernet cable?  It should work and give you the same functions as wireless.  Your computer or router will not care how the printer is connected.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

Maybe you are looking for