Printer LJ 1022n will not stop printing

Installed with lj-1018-1020-1022 HB-Win64-en on a new W7 64 bit machine on a ethernet network. The printer printed the Windows test page and when I tried to print a document it would not stop and I stopped by canceling it in the print que. Printer works quite well on a XP network.

Hey Henry,
Try following the steps in the document linked below. Let me know if it is able to get your printing to return to normal.
Product Continuously Prints the Same Print Job After it is Installed on a Network
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------
I am not an HP employee.

Similar Messages

C4580. Will not stop printing.

I have a very big problem with my printer. It will not stop printing once I send a print job to it (regardless of the program in windows, or whether it is a test page etc). I have had this problem since new and have been unable to use the printer properly since I first bought it.
The problem is as follows - whenever I print, the printer just keeps churning out and printing the same page time after time after time. I have to manually cancel the job. I have reinstalled and reset the printer 3 or 4 times now with no effect. Even when I do the very initial print test on photo paper (and put one sheet in), it prints but then says it is out of paper (as I delibrately only put one sheet in the tray). This is driving me bonkers. I have spoken to HP support on this several times. I have wasted countless paper and half the ink cartridges - and this is just to TRY and setup the printer! Madness.
This is NOT a printer problem but something wrong with the driver/software. The reason being this:
- I do NOT have this problem if I print to the C4580 using the generic HP 6500 driver (this is what HP recommended when they were helping me). However, I do not want to use this driver as it defeats the object of having an all-in-one and being able to scan); and
- If I do a test print from the printer (as opposed to on my computer), it only prints one page.
Also, this does not seem to be a corrupt print spooler as I have stopped and restarted this several times.
Advice please, otherwise I am sending this back to HP and claiming damages.
Thanks
Elliot

I have the exact same issue. Have you managed to figure out a fix?

MY PRINTER WILL NOT STOP PRINTING

I have a brand new HP 309a wireless printer. I am using it with a USB PORT. I downloaded something from a PDF file and the printer will not stop printing. I rebooted the computer, I disconnected the printer for an hour and when I turned it on it resumed I hit the cancel button, the display reads "print cancelled" and then it reads "now printing." When I attempt to use the printer to print something else it reads "busy." HELP.
This question was solved.
View Solution.

Hi,
Disconnect the USB cable and follow the below steps to restart the spooler service.
Click Start (Windows logo) >> All Programs >> Accessories >>
Right click on Command Prompt and open it as Administrator ( choose run as administrator)
Enter the below command in black window and hit enter key..
net stop spooler
That will stop the spooler service.
Then enter the below command and hit enter key to start the spooler service
net start spooler
That will delete the current print comment and the things in print queue.
Press the widnows key and R key on the key board to open run window ( Click on Start >> Run).
In run window enter services.msc and click Ok.
That will open services window.
From there double click on the print spooler service.That will open a new window.
Click on Stop button to stop and then click on start button to restart the spooler service.
Make sure that startup type is : Automatic and Service status is : Started
Click on Apply and Ok to close the services window.
If the issue resolved,
Say "Thanks" by clicking the Kudos Star in the post that helped you.
Saul
Tech Support Eng.
HP

Distiller will not stop distilling postscript file

I use Distiller 6.0.2. Lately, when I try to distill a Quark layout into a pdf the distilling process will not stop. The progress bar shows a number that just keeps on climbing up. It seems if I quit the program and then restart it, this will solve the problem and distiller will make a pdf of the postscript. However, I will get the same problem once I try to distill another page. I tried to trashing the Distiller preferences and then restarting the program. This did not do anything.

It's not a specific file and it doesn't matter how big a file is. I am distilling a postscript file. My Mac is running on 10.3.9. I only print from Quark to get postscript files.

Laserjet cm1415 will not stop showing "Incoming Call"

I have the fax setup in manual mode and it will not stop showing "Incoming call" on the panel even thjough there is no call comming in. Other than that everything works well. Any body have any ideas on how to get it off of that so the printer can go into sleep mode?
Thanks

The "Incoming Call" message is shown whenever we see a ring signal on the line, regardless of the fax receive mode.
If this message is showing up when no fax is being sent, then it means that there is noise on the phone line. You can contact your phone company to discuss options in reducing the noise on your phone line.
If this message is showing up with no phone line plugged in, then the modem inside the printer is detecting noise. It is possible that the internal fax parameters have become corrupt. If that is the case, then you can perform a "Restore Defaults" in order to reset them. Note: doing this will erase all of your settings. You can print out a configuration report before doing this so you can reset them. A restore can be done at the control panel by pressing [Setup] on the main screen (the button with the wrench on it), then select "Service" and then "Restore Defaults."
This is based on my own experience with the product.
I am an HP Employee.

Rebuilding aMacBook 1.83 GHz Intel Core Duo, hard drive failure so rebuilding system. Aircard will not stop self-assigning IP address. Any ideas how to resolve successfully?

Had hard drive failure on MacBook 1.83 GHz Intel Core Duo, so had to rebuild the OS on new drive. Was on Lion 10.7.5 prior to failure, but had to reinstall Snow Leopard 10.6.3 since that was most recent OS on media I had. After finally getting ethernet connection to router working, was able to get to internet and download / upgrade to 10.6.8. I assume I can probably buy the upgrade to Mountain Lion 10.8 from there.
Problem is this, Airport will not stop self-assigning IP address for my wireless connection, and unless I can get wireless back on this laptop, doesn't make a lot of sense to continue the rebuild and reinstall of all the software that was on it prior to HD failure. Only way to my home network and router is ethernet now. Everything else on my network (Apple MacBook Pro laptops, iPhones, desktops, and non-Apple printers and laptops) is hooking up to router wirelessly fine.
Any ideas how to resolve successfully so that the airport will stop self-assigning and allow the router to assign the IP address?

When see the beachball cursor, note the exact time: hour, minute, second.
These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
The title of the Console window should be All Messages. If it isn't, select
          SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
          View ▹ Show Log List
from the menu bar at the top of the screen.
Each message in the log begins with the date and time when it was entered. Scroll back to the time you noted above.
Select the messages entered from then until the end of the episode, or until they start to repeat, whichever comes first.
Copy the messages to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
The log contains a vast amount of information, almost all of it useless for solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
Some private information, such as your name, may appear in the log. Anonymize before posting.

My ipod touch will not stop playing music

My ipod touch will not stop playing music. I will pause the music, leave the playlist, and after 30-60 seconds, the music starts playing again. I use my ipod when I run and when I drive (hook it up to the stereo). It is very annoying when I stop to take a phone call or listen to directions, turn off my music, and then hardly a minute into my stop, the music starts right back up again.

FUEL1996, not correct. Apple does not allow one app to control another app.
laurathecellist
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Unsync all music and resync
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

Itunes 10 will not stop auto syncing

I have itunes 10 on a mac and a 160 gb ipod classic.
it will not stop auto syncing when I plug in my ipod, even though "do not auto Sync" button is checked as well as checking off "do not open itunes automatically.
It syncs FOREVER. I would love to find a way to stop this from happening. I dread plugging in my ipod to put on new music etc.

I have had this problem with Windows 7 and iTunes updates for some time. Each time it takes hours to solve but with the over the air upgrade to IOS6 on my iPhone and iPad, I was determined to solve and remember what I did, So here it is:
http://www.care4pcs.co.uk/2012/09/pear-shaped-apple-ios-6-for-iphone-ipad.html
I hope this helps you and any other users.

My data wheel will not stop spinning (i think i am being tapped)

iphone 3GS 3.1.3 16gb white not jailbroken completly stock
ok every time i open up my native phone app the data wheel instantly starts spinning and will not stop. it does stop as soon as i close it.
i thought it might have something to do with google sync so i deleted my mail account but it did not help aat all
PLease help this is driving my crazy

Perhaps it's trying to access your voicemail. Is that working properly? Does the Phone app work?
Try resetting your iPhone by pressing the home and sleep buttons until you see the Apple logo, ignoring the slider. Takes about 5-15 secs of button holding and you won't lose any data or settings.

ITunes will not stop verifying

I have an iPhone4 with the latest iTunes (10.1.0.54) and when I plug my iPhone4 in, it will not stop verifying. I used to have this problem if I canceled a sync. It would verify the phone the next time I plugged it in. I did that this time. I canceled a sync, but now it will not stop verifying to do anything else. I have left it plugged in for 14 hours and it just verifies the entire time. I can do nothing else. It is not set to sync automatically. How do I stop this?

I'm having the same problem, but I've got a MacBook Pro (rather than a PC).
Not only does it continue to 'verify' but it won't even let me force quit (says it's restoring my phone ... but after a number of hours it must be done already).

Whenever I open Firefox a series of sirens start and will not stop. Does not happen in Internert Explorer.

When Firefox is opened a series of sirens starts and will not stop until Firefox is closed.
== This happened ==
Every time Firefox opened
== started when I opened a news story from the Sacramento Bee News Paper on line. ==
== User Agent ==
Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; GTB6.4; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729; InfoPath.1)

That is an issue with the "Cool Previews" extension.
See [tiki-view_forum_thread.php?locale=en-US&comments_parentId=678288&forumId=1]

Ever since I upgraded to 4.0, the welcome tab will not stop opening. It's getting rather annoying.

The welcome tab for the new 4.0 will not stop opening every time I open my browser. Each time I open Firefox two tabs open, the welcome page for the new 4.0 and my home page. I updated some time ago and this welcome page is becoming quite annoying. How do I stop it from opening? In the past, it has stopped after the first time I open Firefox following an update.

Thank you for the reply. I have Google set as my homepage, and that's the only homepage listed in the Options box. I tried restoring to default, but when I opened again, the 4.0 page and Google opened again. That leads me to think it might be options, but that article meant absolutely nothing to me.
What I find strange is that when I have one Firefox window open, then open another Firefox window, only the Google page opens, not the "get to know 4.0" page.

Playhead will not stop at the end

When I play my project in FCP the playhead will not stop at the end but will continue for a few seconds. So when I want to share my project I have to make a range so that I don't have a black clip at the end. There's no gap or what so ever on the timeline. How can I solve this? Thanks for your answers.

Unfortunately, the problem is not solved. When I hit the end key the playhead goes to the end. Actually one frame further. Because when I go back one frame, I get the end clip symbol in the corner. But if I just play, the palyhead goes further for a 3 seconds. Then I get the clip symbol "negative edge" on the rightside. See also image. And there is nothing in the timeline.

HT201304 how to disable siri? siri will not stop talking, and is making it impossible to use my iphone 4s.

Siri will not stop talking, virtually making using my phone impossible. Please help me disable siri?

Settings>General>Siri> turn off.

Nano will not stop scrolling songs

Nano is continually scrolling through all songs without allowing me to play any of them. It just starting doing this after using it without problems for over a year. It will not stop, but scans through all songs without letting me play them. When I touch the play button it stops for a split second then goes back to scanning all my songs. I have tried everything to fix it.

Okay, the problem is fixed. Try this, It worked for me.
Deauthorize and reauthorize your account in iTunes
In some cases iTunes may "forget" that your music is authorized. You can refresh the authorization by deauthorizing and then reauthorizing your computer. To deauthorize a computer:
1. In iTunes, choose Deauthorize Computer from the Store menu (your computer needs to be connected to the Internet).
2. In the resulting dialog, enter your Apple ID and password.
3. Click OK.
You can now reauthorize your computer by simply trying to play one of the songs you've purchased. A dialog box will appear asking you to enter your Apple ID and password. Once you have done so, click Authorize to finish the process.
Message was edited by: the-chocoholik

Printer LJ 1022n will not stop printing

Similar Messages

Maybe you are looking for