Printer M1522nf stops working if unused for 30 minutes.

printer will not respond to print or fax request if 30 minutes of non use has lapsed. I musst turn off then back on. Printer is not connected to PC. control panel remains lighted

Hi Tobias,
Is the screensaver triggering the disconnection of network?
Try disabling the screen saver and check.
Regards,
Rave

Similar Messages

My linksys E1200 stop working when unused for many hours or days...

Hi!
I'm really deceive by my Linksys E1200... If I dont use internet for few days, internet stop working (tablet, computer, cellphone, etc...). Even with my old computer directly connected to the router with a cable. To make it work again, I need to unplug and replug the power cable of the E1200 ... I'm tired of that!!!!
I'm correctly updated (2.0.06) If you can't help me I will change the router and It will not a Sisco product...
I found this comment on an other thread and I really think I'm experiencing the same issue. :
Re: Linksys E1200 - Internet Stops Working
10-22-201311:43 AM
I've seen the same problem with the E1200. It was issued to my by my cable company (RCN) and I need to power cycle it every few days.
I think it has something to do with dhcp renumbering or renewal, but not sure.
I updated to 2.0.06 but that didn't help.
I'm just going to switch to a different router.
Best Regards

Internet Service Provider and Modem Configurations
What ISP Service do you have? Cable or DSL?
What ISP Modem Mfr. and model # do you have?
Is ISP Modem/Service using Dynamic or Static WAN IP addressing?
What ISP Modem service link speeds UP and Down do you have?
Check cable between Modem and Router, swap out to be sure. Link>http://en.wikipedia.org/wiki/CAT6 is recommended.
Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask.
For DSL/PPPoE connections on the router, ensure that "Always ON" option is enabled.
If the ISP modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>http://www.practicallynetworked.com/networking/fixing_double_nat.htm and http://cognitiveanomalies.com/cisco-nat-how-nat-works/. If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ. Also check the routers DHCP IP address maybe conflicting with the ISP modems IP address of 192.168.0.1. Check to see if this is the same on the ISP modem, and if modem can't be bridged, change the DIR router to 192.168.1.1 or .0.254.
I recommend that you have your ISP check the cabling going to the ISP modem, check signal levels going to the ISP modem. For cable Internet, RG-6 coaxial cable is needed, not RG-59. Check for t.v. line splitters and remove them as they can introduce noise on the line and lower the signal going to the ISP modem. Connecting to the ISP modem could result in a false positive as the signal to the modem could be just enough to that point then adding on a router, could see problems. The router operation is dependent upon getting good data flow from the ISP modem and the modem is dependent upon getting good signal from the ISP Service.

Safari and firefox stop working after a few minutes of browsing, regardless of what site I'm on. I have to restart my computer to get internet access again but it only works for a few more minutes, then I have to restart again. Please help!

Safari and firefox stop working after a few minutes of browsing, regardless of what site I'm on. I have to restart my computer to get internet access again but it only works for a few more minutes, then I have to restart again. I don't get a spinning ball, it just stops working at whatever page it's on. I can close the program just fine but when I re-open it, either safari or firefox, it freezes trying to load the hompage. This started a few days ago after trying to stream a movie on my computer. I'm on a Mac Air OS X Version 10.6.8 and have downloaded all updates. When I go into finder, it says I have over 80 gigs available. Is there some other memory cache that I need to check? Thanks so much for your help.

ejwoodall wrote:
It's not a router problem as I explained in my post. If it was a router problem then I wouldn't have the problem everywhere I go. It is an issue with the software.
Then I guess the millions of people running 10.5.7 with no issues are just hallucinating that their machines are working fine?
I'm not trying to belittle your issues; you're certainly having them and I know first hand how annoying an intermittent AirPort issue can be. (In fact, mine was due to an AirPort driver bug that no one else seemed to suffer from.)
The single best diagnostic you could do is take your system running 10.5.7 to an Apple Store, and try using their in-store network.
If your machine performs flawlessly, it may be a router issue.
If your machine has connectivity issues there, it may be a hardware problem with your machine.
There have been numerous people in multiple threads over the years who swore that an update was buggy because things used to work, but returned later to sheepishly admit that they took their machine in, a problem was found and fixed, and now their Mac works flawlessly with the newer software.
But simply reinstalling 10.5.5 in no way means the explanation of how firmware bugs may be at play here is incorrect.
In the context of that explanation, all you've done is possibly reinstall software that asks to add "2 + 3."

Printer MX320 stopped working and shows: close feeder cover

Printer MX320 stopped working and shows: close feeder cover

Hello,
Please try pressing the OK or STOP button to clear the error.
If the error remains, it may be due to the application you are scanning from not supporting scanning from the ADF. However, if the issue persists, it would be best to get in touch with our technical support team at http://bit.ly/Phone_Support for further assistance.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

CS4 OpenGL stops working after a few minutes of painting

Hi,
CS4 OpenGL stops working after a few minutes of painting. It doesn't seem to have anything to do with the amount I paint. If I save the file, then reopen I can paint for another few minutes before the opengl stops working. Is this a standard problem with CS4? Is there a solution? Thanks! PJ
System Specs:
Windows XP SP3, updated
Latest DirectX & all software updated
Nvidia Geforce 9600 GT 512MB w/ latest driver
Athlon64 X2 Dual 3800+
2GB RAM
Photoshop CS4

Joining the party...
I am having the EXACT same issue, PLUS my Wacon PTZ-430 only works for a fewminutes then, when the Open GL craps out, so does it... but only certain aspects. The cursor still moves, it just will not paint. Mouse will (direct via USB) but the tablet won't. If I delete CS4 prefs, then the Wacom works fine... for a while. Latest Wacom drivers and bee on the phone w them. All is fine under CS3.
From DXDiag:
System Information
Time of this report: 12/8/2008, 15:37:52
Machine name: VM-EDITING
Operating System: Windows XP Professional (5.1, Build 2600) Service Pack 3 (2600.xpsp_sp3_gdr.080814-1236)
Language: English (Regional Setting: English)
System Manufacturer: VELOCI
System Model: 122-CK-NF68
BIOS: Phoenix - AwardBIOS v6.00PG
Processor: Intel(R) Core(TM)2 Duo CPU E6850 @ 3.00GHz (2 CPUs)
Memory: 2814MB RAM
Page File: 1049MB used, 3652MB available
Windows Dir: C:\WINDOWS
DirectX Version: DirectX 9.0c (4.09.0000.0904)
Dual Monitor:
NVIDIA GeForce 8600 GT
Manufacturer: NVIDIA
Chip type: GeForce 8600 GT
DAC type: Integrated RAMDAC
Device Key: Enum\PCI\VEN_10DE&DEV_0402&SUBSYS_043910DE&REV_A1
Display Memory: 256.0 MB
Current Mode: 1920 x 1200 (32 bit) (60Hz)
Monitor: Plug and Play Monitor
Monitor Max Res: 1600,1200
Driver Name: nv4_disp.dll
Driver Version: 6.14.0011.7824 (English)
DDI Version: 9 (or higher)
Second:
Card name: NVIDIA GeForce 8600 GT
Manufacturer: NVIDIA
Chip type: GeForce 8600 GT
DAC type: Integrated RAMDAC
Device Key: Enum\PCI\VEN_10DE&DEV_0402&SUBSYS_043910DE&REV_A1
Display Memory: 256.0 MB
Current Mode: 1280 x 1024 (32 bit) (60Hz)
Monitor: Plug and Play Monitor
Monitor Max Res: 1600,1200
Driver Name: nv4_disp.dll
Driver Version: 6.14.0011.7824 (English)
DDI Version: 9 (or higher)

Upgrade to Yosemite 10.10.1 caused my Canon Pixma ip8500 printer to stop working. Canon no longer supporting this printer. Any solutions?

Upgrade to Yosemite 10.10.1 caused my Canon Pixma ip8500 printer to stop working. Canon no longer supporting this printer. Any solutions?

Hi
try this
resolve my printer problem.
with Yosemite, Apple have upgraded CUPS to 2.0, and CUPS work different. So you need to change one think in configuration.
open terminal, and write the following commands:
sudo sh -c 'echo "Sandboxing Relaxed" >> /etc/cups/cups-files.conf'
you asked for the password for superuser
sudo launchctl stop org.cups.cupsd
after this check in print queue if the printer is ready and not in pause mode.
The printer now should work, if the printer only print in B&W you need to change the configuration in CUPS web interface.
try http://localhost:631/ ; if you receive a error telling the web interface is disabled, type in terminal services the following
cupsctl WebInterface=yes
after this try again http://localhost:631/
after this choose in the web page "Adding Printers and Classes", bellow the CUPS for Administrators title.
in the new page, choose manage printers; after this choose your printer.
in the page of printer choose from the second combobox the option "set default options";
in the option page, change the color mode from monochrome to color, and save hitting the button "set default option", you be asked for a user and password with admin privileges.
After this your print is ok.

Touch screen L2105 always stops working after a few minutes

I have windows 8.1 and the touch screen always stops working after a few minutes- ie. the touch operation via USB, the screen itself is OK.Have tried windows switching power saving off, but no help
charsepp

Hello charsepp,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand that the touchscreen stops working after a short period on your HP L2105 Monitor. The first thing you are going to need to do is determine if this is a monitor or PC issue. To do this you should try connecting the monitor to another computer and see if the issue persists.
If the issue does not persist it is the computer, and if your computer is also HP I would be happy to assist you, but first I would encourage you to post your product number for your computer. I am linking an HP Support document below that will show you how to find your product number. As well, if you could indicate which operating system you are using. And whether your operating system is 32-bit or 64-bit as with this and the product number I can provide you with accurate information.
How Do I Find My Model Number or Product Number?
Which Windows operating system am I running? Is the Windows Version on My Computer 32-bit or 64-bit?
If the issue persists when you try the monitor on another computer then the issue appears to be a physical issue and I think it would be best if you contacted HP technical support for repair options.
US support link to contact options for HP products purchased in the US.
Outside of US support link to contact options for HP products purchased outside the US.
Please re-post if you require additional support. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Finger print recognition stops working after a few uses with IOS 8

Why does my finger print recognition stop working on my IP6 and IOS 8.1.2 after a few uses. I re-enter finger prints and it stops working again after a few uses.

No one here would know. What troubleshooting steps have you taken so far?
Basic Troubleshooting Steps when all else fails
- Quit the App by opening multi-tasking bar, and swiping the App upward to make it disappear. (For iOS 6 older, hold down the icon for the App for about 3-5 seconds, and then tap the red circle with the white minus sign.)
- Relaunch the App and try again.
- Restart the device. http://support.apple.com/kb/ht1430
- Reset the device. (Same article as above.)
- Reset All Settings (Settings > General > Reset > Reset All Settings)
- Restore from backup. http://support.apple.com/kb/ht1766 (If you don't have a backup, make one now, then skip to the next step.)
- Restore as new device. http://support.apple.com/kb/HT4137 For this step, do not re-download ANYTHING, and do not sign into your Apple ID.
- Test the issue after each step. If the last one does not resolve the issue, it is likely a hardware problem.

Print Page stopped working, how to solve?

Dear,
Print Page stopped working, how to solve?
Guys anyone knows a material with step by step how to create a page impression?
I have an application where there is a page printer which generates a PDF but the PDF page rendering is no longer any more field returned from the sql query.
If someone does not have a material for me incidar no way give me a hand?
grateful for the attention
Edited by: goj1 on 07/05/2013 18:34

Actually what happened was the following:
There is a page with a report of 4 fields. This field was rendered in a PDF document is blank in shared components -> Reports
This PDF with 4 fields are used when you want to print the report.
After an update the application when I try to print the PDF opens blank.
Work in a government agency and is not how I use PL / PDF.
Thanks.

Why CD audio reproduction stop working after about 20 minutes

Why CD audio reproduction stop working after about 20 minutes.
The energy saving options seem to be ok

Welcome to Apple Support Communities marimonf. We are sorry you are having problems with what sounds like you burning a CD. These documents may provide some useful information:
iTunes 12 for Mac: If you have trouble burning a disc
iTunes 12 for Mac: Burn settings
iTunes 12 for Mac: Create your own CDs and DVDs

Printer, CP4025, stopped working with Windows 10 upgrade

When I did my Windows 10 upgrade my Printer, CP4025, stopped working. I tried deleteing and added, wouldn't work.So i went back to Windows 7 because I have to be able to print today. But it still will not work. Now it will not add, getting a message saying "the folder you specified doesn't contain driver software for your device". Yes, I am using the disk to try and do this. HELP!!!! I am an old lady and if you go too techincal I will just be further confused.

You may need the AMD chipset driver for that one. Select the first one listed.http://support.amd.com/us/gpudownload/windows/Pages/raid_windows.aspx

HP printer has stopped working - Laserjet p1006

I just installed Windows® 8 Consumer Preview and my HP printer has stopped working. I am using the Laserjet p1006 and I have tried everything, reinstalling the printer, re-downloading drivers etc. but to no avail. Are there new drivers available that work with Windows 8?
Update:
The printer is installed and driver has been picked up by Windows but every time I try and print something, it gives me an error that the document could not be printed.
Any suggestions

Really Thanks God
i Found solution of this problem Randomly only by praying
The solution
Connect The p1005 printer to a pc have windows 7 and print a page with it and get the cable connected to windows 8 after that and go to control panel > hardware and sounds > Device and printer > hp laser jet p1005 Right click > Printer properties > ports > uncheck bidirectional support then press ok and print ,, it works
Note : after doing the pervious steps if u turned the printer off u will need to connect it to windows 7 pc again and print and connect it to windows 8 it will work without the pervious steps //
it seems like if windows 7 gives it information that is reseted after turn it off
we wish windows 8 to solve this problem nearly
That is the Original post page : http://answers.microsoft.com/en-us/windows/forum/windows_8-hardware/laserjet-p1005-will-not-print/34...

I have iphone 3gs, while connecting, it shows sync in progress, then in my pc shows backing up step 1,2,..5, then message comes itunes stopped working-windows checking for solution. Then another message comes that "A problem caused the program to stop wor

When i connect my iphone 3GS to my PC, while syncing in progress, pc shows backing up, preparing to sync. Then message display "itunes stopped working",
windows checking for solution, Then message comes "A problem caused the program to stop working correct. Windows will close the program and notify you if solution is available" , Then Itunes go off. I have tried agains installing Itunes etc no use. I am not a computer literate, help me to resolve this, Thanks

I have already copied my photographs to the a library manager but when I tried to reuse iphoto and import the photos back into iphoto, it would not let me.
You can't "copy" your photos to the "library manager", there is just no way to any such thing.
Option 1
Back Up and try rebuild the library: hold down the command and option (or alt) keys while launching iPhoto. Use the resulting dialogue to rebuild. Choose to Repair Database. If that doesn't help, then try again, this time using Rebuild Database.
If that fails:
Option 2
Download iPhoto Library Manager and use its rebuild function. (In early versions of Library Manager it's the File -> Rebuild command. In later versions it's under the Library menu.)
This will create an entirely new library. It will then copy (or try to) your photos and all the associated metadata and versions to this new Library, and arrange it as close as it can to what you had in the damaged Library. It does this based on information it finds in the iPhoto sharing mechanism - but that means that things not shared won't be there, so no slideshows, books or calendars, for instance - but it should get all your events, albums and keywords, faces and places back.
Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one.
Regards
TD

HT201407 My iphone suddenly stops working and asked for activation required. I did restore it thru itunes but it asks me to turn off "find my iphone". How can i disable "find my iphone" if i can open the iphone itself. please help me.

My iphone suddenly stops working and asked for activation required. I did restore it thru itunes but it asks me to turn off "find my iphone". How can i disable "find my iphone" if i can open the iphone itself. please help me.

My iphone 5 suddenly stops working and asked for activation required. I did restore it thru itunes but it asks me to turn off "find my iphone". How can i disable "find my iphone" if i can't open the iphone itself. please help me.

When I open a PDF document and select print, Adobe stops working and closes. How do I correct this?

When I open a PDF document and select print, Adobe stops working and closes. How do I correct this?

Hi tbytrzll,
In order to help you better please let me know below mentioned information:
- Operating system version and name.
- Version of Adobe reader.
- Have you tried to update the Reader and if you are trying to print using any other application what is the result.
Have you tried any steps to resolve the issue.
Regards,
Ajlan Huda.

Printer M1522nf stops working if unused for 30 minutes.

Similar Messages

Maybe you are looking for