Printer shifts artwork off centre

I have a PDF created from PS CS6 which is a Letterhead layout. The design has two lines (strokes) that run down the left side of the page. ( see image below )
Consequently I am wanting to print this to an 'HP Photosmart 7520' with borderless printing.
Unfortunately the result always appears to shift the artwork to the right subsequently the graphic strokes are shifted away from the left edge. ( see image below )
I have checked all the printer and acrobat settings and have tried printing; 'actual size' and 'fit' options but have no success. I have tried printing direct from PS but it is the same. I wonder if it could be a driver issue.
Any help on this would be much appreciated

its temporary fix/workaround, but have you thought of creating a custom paper size and tricking it into printing correctly?
or rotating the saved image upside down in reference then having a wide blue border that essentially gets cut off?

Similar Messages

Printing with Border off centre

When i try to print a 4x6 print with a border the print module is putting the following minimum margins: L 0.35 R 0.32 T 0.28 B 0.53 so the rpint is off centre. I can't make these any smaller and making them all 0.53 looks to big. Any ideas it doesn't put the image centrally?
I tried resizing the image in PSE5 editor to exacly 4x6 but made no difference.

I tried borderless and it does set the margins to zero. However when I put in 0.2 cm and print it doesn't come out quite right. Looks fine on the LR preview. Cell dimension in LR are correct at 14.84x9.76 but actual print is 14.6 x 9.8 and sightly off centre (L 0.15 R 0.25).
This is much better than I was getting as had a look in the Canon print properties and under Page Layout in the Borderless section there is a slider "Amount of Extension". I set this to the left so the minimum and got a big improvement.
That's close enough to be usable at least tks Jao

My A4 centred document keeps printing out off centre.

I have an A4 Document which has everything centred, when i print out the document is off centre and I can't figure out why this is happening. I have tried exporting as pdf & jpgs and when i print those out they are off centre too. The actual InDesign document is aligned to the centre perfectly though!
Help!

I just want to be clear about what "the same direction" means. After rotation the same elements are too close to the same edge of the page.
If that's true on all the prints, the problem is in the communication between ID and the printer (and that's not all that unusual with Ricoh printer drivers and ID). ID is not known for it's native printing, and it doesn't get along with some print drivers at all. Top of the list is HP, and Ricoh might be second. In such cases exporting PDF and printing from Acrobat is the suggested workaround. It disturbs me, though that you say the PDF also prints off center, which is why I think this is a printer problem.

Print problem - prints fine in photoshop and windows but direct from illustrator is off centre when printed.

when printing a full page image from illustrator the print is off centre and does not print the image in line with the paper. the same image prints just fine in photoshop and as a jpeg from windows own program. the positioning is zeroed in the dialouge box and the preview image shows how it should print, but it does not print as shown. please help.

clarke,
What happens if you Save a Copy as PDF, then print from Acrobat or Reader?
If that helps, you may consider trying to (find and) use a PostScript (emulatin) printer driver to your printer, if possible.

Page up and page down = pages go off centre

A very basic question: when flipping through the pages of a book I've laid out, it would be nice if using the page up or down keys moved to the next page and centred them. Instead, however, the pages are moved knocked out of centre each time. How to get around this?
This happens at all sizings except for 100%. The page size is closest at 127% to the actual physical printed page. There should be a way to set this as the defaul page size. At 127% the up and down keys result in the page dancing bout the screen going off centre both horizontally and vertically. At 100% the centreing is fine verticallz as you flip through the pages, but depending on whether its an odd or even page, the pages will still jump around horizontally. I'm working in spreads.
Thank you.

... and Shift-PageUp/PageDown is the default for moving through the document in discreet pages.
But if your like me and prefer PageUp and PageDown to move a full page, you can edit the shortcuts to work that way.

HP Designjet T520 Printing A3 cuts off at bottom

HP Designjet T520 Printing A3 cuts off at bottom When we plot something with AutoCad, and then print Portrait, it all prints fine except the bottom edge is slightly cut off. The paper we are using is A3, and the printer and Autocad settings is A3. Any ideas? WINDOWS 7 - NO ERROR MESSAGES

This very same issue is affecting me with T520.This happens with vertical A4 and A3, and till now I've not yet found a solution. To be sure to be within printer margins I've set the drawing actual margins on all the four sides to be 1.8 cm from paper sheets borders.But as alway I get the bottom border cut, while the upper border seems shifted downward and it's placed at 3,0 cm from the upper border of the paper. BUTif I set the page to be ORIZONTAL in the application, choose the orizontal page format etc the printout is perfectly aligned. To me this seems a weird issue.Experienced this issue using Archicad 16, Illustrator and Indisign. On OSX, from Snow Leopard to Mavericks. These are my printer details:Nome prodotto HP Designjet T520 24inNumero modello prodotto CQ890A Versione firmware AXP2CN1437AR

Unable to print album artwork

After burning a CD i'm unable to print the album artwork off. it says it's sending to printer but printer just feeds a blank sheet of paper straight through. Please help.

CDs don't contain artwork so you wouldn't find any connected with the files that were burned. When you download music from the iTunes Store a proprietary format artwork file for the tracks you download is placed into the Album Artwork folder inside your iTunes folder. That's why you can see artwork against the original file(s) in iTunes and not against the files on the CD. You should be able to print a CD insert for the album using the tracks in iTunes. Highlight the album tracks and go to Edit>Print>CD Jewel Case Insert, choose the style of insert you want from the Theme menu.

HP Laserjet Pro 100 Color MFP M175nw Print missing/faded down centre of every page

HP Laserjet Pro 100 Color MFP M175nw. Operating on Windows 7 from my laptop wirelessly. Just bought this new a few day's ago and each page of print has about 20mm wide streak missing print running down the centre. what can I do to correct this problem? I have tried printing a cleaning page a couple of times and calibrating color from the Print Quality Menu also a couple of times but this has made no difference. I'm using a Premium quality paper for use in laserjet printer's. Could someone please advise me what I can do. Thanks in anticipation.
This question was solved.
View Solution.

Hi Watcher35,
I see that the new Laserjet Pro 100 MFP M175NW is missing print down the center of the pages, you have ran cleaning and color calibration but the issue is not resolved.
Would this be an accurate example of the issue: but with the "Bb" would be completely missing?
This HP document: Resolving Print Quality Issues may take you though some of the same steps you have already done, I suggest not skipping any steps.
If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here.
Regards,
JERENDS
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

My printer keeps going off line with my network. have to set everything up every few minutes.

After getting my HP photosmart 5510 all in one printer setup on my wireless network and setup for eprint, 2 problems occurred. The printer keeps jumping off of the network, and I have to set everything back up again. Also, even with eprint still completely set up, none of the emails that I send are printing out???
Please Help

For those who are experiencing ongoing issues with their web services, you can attempt to try the following steps that may help resolve your problems.
1.) Completely shut down your printer and restart it
2.) If you have prints that have not printed, log into ePrint Center (or create an account if you do not have one) and then look for your printer status. If printer status is green but you still have pending jobs, delete the pending jobs one at a time (Starting with the oldest first). There may be a print job stuck in the queue that further restricts other jobs from completing.
If option 1 or 2 above still doesn’t work, removing web services and re-adding web services will cause the printer to reattach to the cloud.
Please note that if you attempt option 3, you will get a new eprint email address (and lose your custom one with no ability to get it back) furthermore, you will need to re-add your printer back to your ePC account.
I am an HP employee

How do I set up my HP 7520 to print card stock off Avery 8859 design???

Trying to print business cards after designing on Avery 8859 card stock design. HP 7520 All in one will only print a test page of thumbnails of the business cards even though it shows the correct size, etc. for the 8859 paper.
How do I set the printer for card stock, etc. as Avery describes, and what is going wrong?? I have wasted many hours, and lots of paper, and still NO BUSINESS CARDS!!!

Hi @klmrazek,
Welcome to the HP Forums!
I noticed that you are wondering how to set up your HP 7520 to print card stock off Avery 8859 design? I am sorry for the frustration, but happy to look into this for you!
From what I can find, the card size you are using is 2" x 3 1/2". This is an unsupported paper size with this particular printer. According to your printer specifications, here are the supported card stock sizes:
Card type
Card size
3 x 5 in Index
76.2 x 127 mm (3 x 5 in)
4 x 6 in Index
101.6 x 152 mm (4 x 6 in)
5 x 8 in Index
127 x 203.2 mm (5 x 8 in)
However, you might be able to get around this by assigning an alternate driver, by going through this post, How to Assign Alternate Print Drivers in Different Versions of Windows, by @Shane_R. Then try a custom size print by going through this guide, Create Custom Paper Sizes in Windows 7, Windows 8, and Mac OS X.
Otherwise, I would suggest a different size of paper, within your supported sizes using the chart provided. Or you can also try contacting Avery Support, in case they may have additional software or drivers that you can try.
Hope this information is helpful, and have a good day!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

[FIXED BUT NOT SOLVED] NVIDIA - Desktop shifted left off the screen...

Hello Community!
For a pretty long time right now, I am trying to fix the video setup of my HTPC but without success. Because I'am run out of ideas, I really need Your help.
PROBLEM:
The desktop is shifted left off the screen, round about 100 Pixel.
It started some time in the past, while upgrading a one year old Ubuntu installation (NVDIA drivers). Because I couldn't fix it and also wanted to replace Ubuntu with ArchLinux, I performed a clean ArchLinux installation.
First I used the nouveau drivers ending up with the same problem. I read an configured using xrandr and cvt, but with no success.
So I restored the system to a snapshot taken before X11 and nouveau drivers installations, thank's BTRFS, and installed the proprietary NVIDIA drivers ending up with the same problems. Again I tried all the tips and tricks found in the documentations and forums, used nvidia-xconfig, hand crafted the xorg.conf all with no success.
HARDWARE
The system is a MSI Media Live (http://www.msi.com/product/desktop/Media-Live.html)
. Support AMDR Athlon 64 X2, Athlon 64 and Sempron in the Socket AM2 package
. North Bridge: nVidia® C51PVG Chipset
. South Bridge: nVidia® MCP51 Chipset
. Graphics is Integrated NVIDIA GPU GeForce 6150 LE
. VGA, SCART and HDMI - Connectors
The display Problem is on VGA and HDMI now, where in the past the VGA was perfect. Therefor I connected and used the VGA port only, in all tests.
INSTALLATION HISTORY
2012-12-30 + Installation according ArchLinux install guide
2012-12-31 + pacman -S openssh
systemctl start sshd
2012-12-31 + pacman -S btrfs-progs
2012-12-31 pacman -S sudo
2012-12-31 + sudo pacman -S bash-completion
2013-01-03 + pacman -S rsync wget gptfdisk
2013-01-10 + pacman -Suy nvidia-304xx
2013-01-10 + pacman -Syu nvidia-304xx-utils
2013-01-10 + pacman -S xorg-server xorg-xinit xorg-server-utils
2013-01-10 + pacman -S mesa
2013-01-10 + pacman -S xorg-twm xorg-xclock xterm
2013-01-10 + pacman -S ttf-dejavu
2013-01-10 + pacman -Suy lxdm
2013-01-10 + systemctl enable lxdm.service
2013-01-10 + pacman -S xorg-xdpyinfo
2013-01-10 + pacman -S pkgtools
2013-01-10 + pacman -S pkgfile
2013-01-10 + pacman -S bc
As You can see, I installed only a minimal X11 environment for test. The lxdm display manger shows up but with very small font and shifted to the left. Only if I force a resolution of 1024x768 the image is centered on screen/tv but still the very small font. Obviously not a solution for a HTPC.
Here are the xorg.conf and the Xorg.0.log of my last test configuration.
xorg.xonf
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 304.64 (buildmeister@swio-display-x86-rhel47-12) Tue Oct 30 12:04:46 PDT 2012
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0" 100 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
EndSection
Section "Files"
EndSection
Section "InputDevice"
# generated from default
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons" "no"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
# generated from default
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Unknown"
ModelName "Unknown"
HorizSync 28.0 - 33.0
VertRefresh 43.0 - 72.0
Option "DPMS"
EndSection
Section "Device"
Identifier "Device0"
Driver "nvidia"
VendorName "NVIDIA Corporation"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Device0"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Depth 24
EndSubSection
EndSection
In the Section "ServerLayout" I modified the line
Screen 0 "Screen0" 100 0
by adding the 100 0 at the end.
Xorg.0.log
[ 12.997]
X.Org X Server 1.13.1
Release Date: 2012-12-13
[ 12.997] X Protocol Version 11, Revision 0
[ 12.997] Build Operating System: Linux 3.7.0-1-ARCH x86_64
[ 12.997] Current Operating System: Linux media-pc 3.6.11-1-ARCH #1 SMP PREEMPT Tue Dec 18 08:57:15 CET 2012 x86_64
[ 12.997] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=0f1f870d-ccaa-4bc2-b149-1792f0c69fce
[ 12.997] Build Date: 16 December 2012 04:45:14PM
[ 12.997]
[ 12.997] Current version of pixman: 0.28.2
[ 12.997] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 12.997] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 12.998] (==) Log file: "/var/log/Xorg.0.log", Time: Fri Jan 18 13:18:12 2013
[ 13.065] (==) Using config file: "/etc/X11/xorg.conf"
[ 13.065] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 13.066] (==) ServerLayout "Layout0"
[ 13.066] (**) |-->Screen "Screen0" (0)
[ 13.066] (**) | |-->Monitor "Monitor0"
[ 13.066] (**) | |-->Device "Device0"
[ 13.066] (**) |-->Input Device "Keyboard0"
[ 13.066] (**) |-->Input Device "Mouse0"
[ 13.066] (==) Automatically adding devices
[ 13.066] (==) Automatically enabling devices
[ 13.066] (==) Automatically adding GPU devices
[ 13.213] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 13.213] Entry deleted from font path.
[ 13.213] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 13.213] Entry deleted from font path.
[ 13.222] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 13.222] Entry deleted from font path.
[ 13.222] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 13.222] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 13.223] Entry deleted from font path.
[ 13.223] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 13.223] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/
[ 13.223] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 13.223] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
[ 13.223] (WW) Disabling Keyboard0
[ 13.223] (WW) Disabling Mouse0
[ 13.223] (II) Loader magic: 0x7fcc40
[ 13.223] (II) Module ABI versions:
[ 13.223] X.Org ANSI C Emulation: 0.4
[ 13.223] X.Org Video Driver: 13.1
[ 13.223] X.Org XInput driver : 18.0
[ 13.223] X.Org Server Extension : 7.0
[ 13.226] (--) PCI:*(0:0:5:0) 10de:0241:1462:3290 rev 162, Mem @ 0xfd000000/16777216, 0xd0000000/268435456, 0xfc000000/16777216, BIOS @ 0x????????/131072
[ 13.226] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 13.226] Initializing built-in extension Generic Event Extension
[ 13.226] Initializing built-in extension SHAPE
[ 13.226] Initializing built-in extension MIT-SHM
[ 13.226] Initializing built-in extension XInputExtension
[ 13.227] Initializing built-in extension XTEST
[ 13.227] Initializing built-in extension BIG-REQUESTS
[ 13.227] Initializing built-in extension SYNC
[ 13.227] Initializing built-in extension XKEYBOARD
[ 13.227] Initializing built-in extension XC-MISC
[ 13.227] Initializing built-in extension SECURITY
[ 13.227] Initializing built-in extension XINERAMA
[ 13.227] Initializing built-in extension XFIXES
[ 13.227] Initializing built-in extension RENDER
[ 13.227] Initializing built-in extension RANDR
[ 13.227] Initializing built-in extension COMPOSITE
[ 13.227] Initializing built-in extension DAMAGE
[ 13.227] Initializing built-in extension MIT-SCREEN-SAVER
[ 13.227] Initializing built-in extension DOUBLE-BUFFER
[ 13.227] Initializing built-in extension RECORD
[ 13.227] Initializing built-in extension DPMS
[ 13.227] Initializing built-in extension X-Resource
[ 13.227] Initializing built-in extension XVideo
[ 13.227] Initializing built-in extension XVideo-MotionCompensation
[ 13.227] Initializing built-in extension XFree86-VidModeExtension
[ 13.227] Initializing built-in extension XFree86-DGA
[ 13.227] Initializing built-in extension XFree86-DRI
[ 13.227] Initializing built-in extension DRI2
[ 13.227] (II) LoadModule: "glx"
[ 13.414] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 15.559] (II) Module glx: vendor="NVIDIA Corporation"
[ 15.559] compiled for 4.0.2, module version = 1.0.0
[ 15.559] Module class: X.Org Server Extension
[ 15.559] (II) NVIDIA GLX Module 304.64 Tue Oct 30 11:18:32 PDT 2012
[ 15.560] Loading extension GLX
[ 15.560] (II) LoadModule: "nvidia"
[ 15.560] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[ 15.868] (II) Module nvidia: vendor="NVIDIA Corporation"
[ 15.868] compiled for 4.0.2, module version = 1.0.0
[ 15.868] Module class: X.Org Video Driver
[ 15.868] (II) NVIDIA dlloader X Driver 304.64 Tue Oct 30 10:59:51 PDT 2012
[ 15.868] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
[ 15.868] (++) using VT number 7
[ 15.875] (II) Loading sub module "fb"
[ 15.875] (II) LoadModule: "fb"
[ 15.984] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 16.008] (II) Module fb: vendor="X.Org Foundation"
[ 16.008] compiled for 1.13.1, module version = 1.0.0
[ 16.008] ABI class: X.Org ANSI C Emulation, version 0.4
[ 16.008] (II) Loading sub module "wfb"
[ 16.008] (II) LoadModule: "wfb"
[ 16.008] (II) Loading /usr/lib/xorg/modules/libwfb.so
[ 16.025] (II) Module wfb: vendor="X.Org Foundation"
[ 16.025] compiled for 1.13.1, module version = 1.0.0
[ 16.025] ABI class: X.Org ANSI C Emulation, version 0.4
[ 16.025] (II) Loading sub module "ramdac"
[ 16.025] (II) LoadModule: "ramdac"
[ 16.025] (II) Module "ramdac" already built-in
[ 16.025] (**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32
[ 16.025] (==) NVIDIA(0): RGB weight 888
[ 16.025] (==) NVIDIA(0): Default visual is TrueColor
[ 16.025] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
[ 16.026] (**) NVIDIA(0): Enabling 2D acceleration
[ 19.582] (II) NVIDIA(GPU-0): Display (Acer AT3220 (CRT-0)) does not support NVIDIA 3D
[ 19.582] (II) NVIDIA(GPU-0): Vision stereo.
[ 19.584] (II) NVIDIA(0): NVIDIA GPU GeForce 6150 LE (C51) at PCI:0:5:0 (GPU-0)
[ 19.584] (--) NVIDIA(0): Memory: 262144 kBytes
[ 19.584] (--) NVIDIA(0): VideoBIOS: 05.51.28.56.19
[ 19.584] (--) NVIDIA(0): Interlaced video modes are supported on this GPU
[ 19.584] (--) NVIDIA(0): Valid display device(s) on GeForce 6150 LE at PCI:0:5:0
[ 19.584] (--) NVIDIA(0): Acer AT3220 (CRT-0) (connected)
[ 19.584] (--) NVIDIA(0): TV-0
[ 19.584] (--) NVIDIA(0): DFP-0
[ 19.584] (--) NVIDIA(0): Acer AT3220 (CRT-0): 350.0 MHz maximum pixel clock
[ 19.585] (--) NVIDIA(0): TV-0: 400.0 MHz maximum pixel clock
[ 19.585] (--) NVIDIA(0): TV encoder: (null)
[ 19.585] (--) NVIDIA(0): DFP-0: 310.0 MHz maximum pixel clock
[ 19.585] (--) NVIDIA(0): DFP-0: Internal Single Link TMDS
[ 19.585] (**) NVIDIA(0): Using HorizSync/VertRefresh ranges from the EDID for display
[ 19.585] (**) NVIDIA(0): device Acer AT3220 (CRT-0) (Using EDID frequencies has
[ 19.585] (**) NVIDIA(0): been enabled on all display devices.)
[ 19.585] (==) NVIDIA(0):
[ 19.585] (==) NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select"
[ 19.585] (==) NVIDIA(0): will be used as the requested mode.
[ 19.585] (==) NVIDIA(0):
[ 19.585] (II) NVIDIA(0): Validated MetaModes:
[ 19.585] (II) NVIDIA(0): "CRT-0:nvidia-auto-select"
[ 19.585] (II) NVIDIA(0): Virtual screen size determined to be 1360 x 768
[ 19.587] (WW) NVIDIA(0): Unable to support custom viewPortOut 1360 x 765 +0 +1
[ 19.588] (WW) NVIDIA(0): Unable to support custom viewPortOut 1360 x 765 +0 +1
[ 19.589] (--) NVIDIA(0): DPI set to (49, 48); computed from "UseEdidDpi" X config
[ 19.589] (--) NVIDIA(0): option
[ 19.589] (--) Depth 24 pixmap format is 32 bpp
[ 19.599] (II) NVIDIA(0): ACPI: failed to connect to the ACPI event daemon; the daemon
[ 19.599] (II) NVIDIA(0): may not be running or the "AcpidSocketPath" X
[ 19.599] (II) NVIDIA(0): configuration option may not be set correctly. When the
[ 19.599] (II) NVIDIA(0): ACPI event daemon is available, the NVIDIA X driver will
[ 19.599] (II) NVIDIA(0): try to use it to receive ACPI event notifications. For
[ 19.599] (II) NVIDIA(0): details, please see the "ConnectToAcpid" and
[ 19.599] (II) NVIDIA(0): "AcpidSocketPath" X configuration options in Appendix B: X
[ 19.599] (II) NVIDIA(0): Config Options in the README.
[ 19.599] (II) NVIDIA(0): Setting mode "CRT-0:nvidia-auto-select"
[ 19.754] Loading extension NV-GLX
[ 19.797] (==) NVIDIA(0): Disabling shared memory pixmaps
[ 19.797] (==) NVIDIA(0): Backing store disabled
[ 19.797] (==) NVIDIA(0): Silken mouse enabled
[ 19.798] (**) NVIDIA(0): DPMS enabled
[ 19.798] Loading extension NV-CONTROL
[ 19.799] Loading extension XINERAMA
[ 19.799] (II) Loading sub module "dri2"
[ 19.799] (II) LoadModule: "dri2"
[ 19.799] (II) Module "dri2" already built-in
[ 19.799] (II) NVIDIA(0): [DRI2] Setup complete
[ 19.799] (II) NVIDIA(0): [DRI2] VDPAU driver: nvidia
[ 19.799] (--) RandR disabled
[ 19.817] (II) Initializing extension GLX
[ 20.522] (II) config/udev: Adding input device Power Button (/dev/input/event3)
only removed the input detection stuff
Question
How can I shift the display to the right?
Many thanks for any hints.
rale
Last edited by rale (2013-01-19 11:46:14)

Mr.Elendig wrote:Switch to dvi/hdmi if you can. Else you have to play with screen calibration etc.
Thank You Mr.Elendig!
The simplest answer often is best. After I connected a TFT display, instead of my TV, I was able to calibrate the screen output and got the desktop shifted. Knowing that, I tried the settings of my TV again. There is a hard to find option for calibration wich is set to automatic but doesn't do it. Trying to turn it of did the trick. Even the option stays on automatic and even the display format is fixed to 4:3 instead of 16:9, finaly the TV adjusted the display correctly.
None the less, the problem not to be able to shift the desktop using the screen paramters in xorg.conf remains.
Thanks
rale

Found 0 results for My browser is missing important items, the whole tool bar...., drop down menu to print, copy, work off line, file, save, book mark, history. I just installed latest foxfire on windows xp. Found some instructions but they called for usi

Found 0 results for My browser is missing important items, the whole tool bar...., drop down menu to print, copy, work off line, file, save, book mark, history. I just installed latest foxfire on windows xp. Found some instructions but they called for using keys my computer doesn't have ( key in OSX There is no file, edit , history, help, tools, navigation, all the things your directions say to use. Also I always get hung up and the message a scrip is running. I don't know what thises scrips are but I sure don't need them.
== This happened ==
Every time Firefox opened
== I just noticed it. It probably happened when I upgraded foxfire.

'''Can't see the Menu Bar''' (File, Edit, View, History, Bookmarks, Tools, Help)?
Turning the Menu Bar on and off is a new feature in version 3.6.
''(Linux & OSX see: [[Menu bar is missing]] )''
''Windows'' Method 1. '''''Hold down''''' the key and press the following letters in this exact order: V T M
''Windows'' Method 2. Press and release the key. The Menu Bar will be displayed; then choose ~~red:V~~iew > ~~red:T~~oolbars and click on ~~red:M~~enu Bar.
The Menu Bar should now be displayed permanently, unless you turn it off again using View > Toolbars. Check mark = displayed, NO check mark = not displayed.
See: http://support.mozilla.com/en-US/kb/Menu+bar+is+missing
'''Navigation Toolbar, Bookmarks Toolbar and other Toolbars''' under View > Toolbars. Clicking on one of them will place a check mark (display) or remove the check mark (not displayed).
'''To display the Status Bar''', View, then click Status bar to place a check mark (display) or remove the check mark (not displayed).
'''Full Screen mode'''
http://kb.mozillazine.org/Netbooks#Full_screen
Also see:
''' [[Back and forward or other toolbar buttons are missing]]'''
'''[[Navigation Toolbar items]]'''

LASER JET 1022N NOT PRINTING SINCE SWITCH OFF

THERE WAS A LARGE PRINT RUN SET UP IN ERROR AND THE PRINTER WAS SWITCHED OFF TO STOP THE PRINTING AS THE REQUEST HAD CLEARED THE COMPUTOR CONTROLS IN PRINT. NOW THE RED LIGHT FLASHES AND NO PRINT, I HAVE BEEN UNABLE TO CLEAR THE MEMORY. THE PLUG AND NETWORK CABLE HAS BEEN DISCONECTED, COMPUTORS HAVE BEEN REBOOTED BUT IT MAKES NO DIFFERENCE. OTHER PRINT REQUESTS DO NOT TRIGGER OFF A RESPONSE. THE RED LIGHT STILL FLASHES.
HELP WOULD BE APPRECIATED
JOHN
3 SEPT 09

Let's set a static IP address for the printer:
- Print a Network Config Page from the front of the printer. Note the printer's IP address.
- Type that IP address into a browser to reveal the printer's internal settings.
- Choose the Networking tab, then Wireless along the left side, then the IPv4 tab.
- On this screen you want to set a Manual IP. You need to set an IP address outside the range that the router automatically sets (called the DHCP range). You can find the DHCP range of the router using its internal settings page or in its manual. Use the CD that came with your router or type the router's IP address (ends in .1) into a browser.
- Use 255.255.255.0 for the subnet (unless you know it is different, if so, use that)
- Enter your router's IP (on the Network Config Page) for the gateway and first DNS. Leave the second one blank.
- Click 'Apply'.
Now, shut down the router and printer, start the router, wait, then start the printer.
After this you may need to redo 'Add a Printer' using the new IP address.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Elements in my IDML file are off centre

Hello, I have a designer who sent me back an IDML file (he's on CS6, i'm on CS5). On my end about 1/3 of the pages in a 100 page document are off centre by the exact same amount.
What's bizarre is that some of the off-centre elements are based off of a Master Page, and the Master Page is perfectly fine. Some pages that use master page elements are fine, while other pages are off centre.
Any idea why this is happening?
Right now i'm going through the pages one-by-one and re-arranging the page elements...

The fact is that IDML is not a tool for collaborative workflows and this
is just the kind of thing that can happen and why everyone should be on
the same version.
Bob

InDesign documents opening off-centre

Hi,
Noticing a few bugs with the new CC apps and one that keeps cropping up is whenever I open an existing document (normally a landscape document) Indesign places it off-centre to the right of the screen. I've got the panels on the right docked to the right edge of the screen and the document isn't set to 'facing pages' which I know can sometimes create the same problem.
Not a major issue but just wondered if anyone gets the same problem and if there is a way to fix it.
Thanks

Eugene Tyson wrote:
I can't test this on my computer as I have XP and CC doesnt' work on it
It was never intended to, Eugene:
http://boblevine.us/is-your-computer-ready-for-adobes-new-creative-cloud-applications/

Printer shifts artwork off centre

Similar Messages

Maybe you are looking for