Printer showing MAC address in sidebar

I have just setup a Canon MX850 printer on my home network and the MAC address of it is showing in the sidebar. The only way to remove it is to change the sidebar preferences which I don't want to do as I want to see other servers on the network. How do I change the printer settings to show the MX850 instead of the printers MAC address?

I have never seen this with any of my Canon printers. I have an iP5200R that is connected wirelessly to my network and an iP6000D that is connected to the USB port of an Airport Extreme. When I configured the iP5200R to join my wireless network, it was displayed in the Canon utility with its MAC address. Also, when I added its printer queue using More Printers > Canon IJ Network, the printer was also shown in the list with its MAC address. However, as I write this reply this printer does not display in any part of the Finder.
Is the printer displayed under the Shared section in the sidebar?
Also, how is the printer connected to your network? Is it being shared by another computer or is it connected via Ethernet or wireless?
PaHu

Similar Messages

  • How to hide or rename the HP Printer's Mac address from Lion Finder Sidebar

    I have an HP d100a all in one printer, and since upgrading to OSX 10.7 (Lion), my printer's mac address shows up in the Finder Sidebar under Shared devices. I understand this is for the printers SD card slot to be shared over my network, however the name is not user friendly.
    Is there a way to rename what is displayed in the Finder window, from the devices mac address to a friendlier name?
    If not, is there a way to disable the sharing of the SD card slot so it is hidden from the sidebar completely?
    I have found several posts from people not knowing what this entry is, but I have not managed to find any posts that explain how to rename or hide the entry.
    Any help would be greatly appreciated. 

    I have also registered to this forum to inform that the problem with showing the MAC-address in the sidebar of the finder is still not solved.
    The strange thing is that the Embedded Web Server says:
    "This specifies the Bonjour domain name assigned to the device, in the form <host name>.local. If a user-specified host name has not been assigned, the default host name HPxxxxxx is used, where xxxxxx are the last 6 digits of the LAN hardware (MAC) address. This option cannot be modified."
    But I did assign a user-specified host name and that name does show-up everywere (also within Bonjour), except in the sidebar of the finder (hp###xx##x####). Lots of people have the same issue, when searching on the interet, but not one has found the solution.
    Please help with solving this issues?

  • 6509E with Sup720 - Show mac address

    I have seen very strange behavior. The following two commands show different outputs...
    core2#sho mac address-table dynamic | in cc04
         7  0009.0fbb.cc04   dynamic  Yes        150   Po10
    core2#sho mac address-table address 0009.0fbb.cc04
    Legend: * - primary entry
            age - seconds since last seen
            n/a - not available
      vlan   mac address     type    learn     age              ports
    ------+----------------+--------+-----+----------+--------------------------
    No entries present.
    Po10 is etherchannel to core1. The MAC address is on the core2 and should never be learned on core1. Core1 doesn't learn this MAC address at all.
    The commands are run at the same time. I repeated many times and it is the same... Any idea why?
    Thanks!
    Difan

    Hi Jon,
    Correct, I am not using VSS. However it is not standard set up. The vlan 7 is extended to many other switches. The root is actually not core1 or core2. It also passes some provider to different location as well. However like you said, all the correct ports are blocked. Please trust me on this.. If there is a loop, we will have much more serious problem... At least our CPU will hike and link will congested, right?
    I know your concern that the same packet could be somehow loopped back through core1, which makes core2 to learn the MAC on the port-channel interface to core1. However when this happens, core1 doesn't learn the MAC anywhere and on core2 some command show the MAC but not the other command...
    Also something interesting, even that MAC in the command will eventually disappear. Please note the aging time. The aging time configured on the vlan is 480 seconds. At last the MAC address is pointing to another interface like G1/1. That interface doesn't even have vlan 7 allowed on the trunk link.
    core2#sho mac address-table address 0009.0fbb.cc04
    Legend: * - primary entry
            age - seconds since last seen
            n/a - not available
      vlan   mac address     type    learn     age              ports
    ------+----------------+--------+-----+----------+--------------------------
    No entries present.
    core2#
    core2#show mac address-table | in 0009.0fbb.cc04
         7  0009.0fbb.cc04   dynamic  Yes        285   Po10
    core2#show mac address-table | in 0009.0fbb.cc04
         7  0009.0fbb.cc04   dynamic  Yes        290   Po10
    core2#show mac address-table | in 0009.0fbb.cc04
         7  0009.0fbb.cc04   dynamic  Yes        300   Po10
    core2#show mac address-table | in 0009.0fbb.cc04
         7  0009.0fbb.cc04   dynamic  Yes        305   Po10
    core2#show mac address-table | in 0009.0fbb.cc04
         7  0009.0fbb.cc04   dynamic  Yes        315   Po10
    core2#show mac address-table | in 0009.0fbb.cc04
         7  0009.0fbb.cc04   dynamic  Yes        320   Po10
    core2#show mac address-table | in 0009.0fbb.cc04
         7  0009.0fbb.cc04   dynamic  Yes        320   Po10
    core2#show mac address-table | in 0009.0fbb.cc04
         7  0009.0fbb.cc04   dynamic  Yes        330   Po10
    core2#show mac address-table | in 0009.0fbb.cc04
         7  0009.0fbb.cc04   dynamic  Yes        335   Po10
    core2#show mac address-table | in 0009.0fbb.cc04
         7  0009.0fbb.cc04   dynamic  Yes        340   Po10
    core2#show mac address-table | in 0009.0fbb.cc04
         7  0009.0fbb.cc04   dynamic  Yes        375   Po10
    core2#show mac address-table | in 0009.0fbb.cc04
         7  0009.0fbb.cc04   dynamic  Yes        405   Po10
    core2#show mac address-table | in 0009.0fbb.cc04
         7  0009.0fbb.cc04   dynamic  Yes        425   Po10
    core2#show mac address-table | in 0009.0fbb.cc04
         7  0009.0fbb.cc04   dynamic  Yes        465   Gi1/1
    core2#show mac address-table | in 0009.0fbb.cc04
         7  0009.0fbb.cc04   dynamic  Yes        480   Gi1/1
    core2#show mac address-table | in 0009.0fbb.cc04
         7  0009.0fbb.cc04   dynamic  Yes        480   Gi1/1
    core2#show mac address-table | in 0009.0fbb.cc04
    core2#show mac address-table | in 0009.0fbb.cc04
    core2#sho mac address-table address 0009.0fbb.cc04
    Legend: * - primary entry
            age - seconds since last seen
            n/a - not available
      vlan   mac address     type    learn     age              ports
    ------+----------------+--------+-----+----------+--------------------------
    No entries present.
    core2#sh int g1/1 trunk
    Port                Mode         Encapsulation  Status        Native vlan
    Gi1/1               on           802.1q         trunking      1
    Port                Vlans allowed on trunk
    Gi1/1               64,72,156,214-216,300,600
    Port                Vlans allowed and active in management domain
    Gi1/1               64,72,156,214-216,300,600
    Port                Vlans in spanning tree forwarding state and not pruned
    Gi1/1               64,72,156,214-216,300,600
    Is it a bug?
    Thanks!

  • CNA 5.5 and show mac address-table

    When trying to Monitor/Search for MAC address in C2960 network I got an error reply that a CLI command is not supported. Analyzing network traffic shows that CNA 5.5 is issueing 'show mac-address-table' command but the latest Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(55)SE does not support 'show mac-address-table' anymore but does support 'show mac address-table' command. How can I change the command for showing mac address tables in CNA 5.5?
    M.

    hi john,
    the show mac-address-table command should be valid.
    check if you've got MAC learning enabled on the ASA interface using show mac-learn command.
    edit: could you post show firewall? the above command works on transparent firewall only.

  • Show mac-address-table not working on ASA5512

    Hi,
    I'm unable to excute "show mac-address-table" on an ASA5512, running 9.1(1). The output is: 
    asa-test# show mac-address-table
                     ^
    ERROR: % Invalid input detected at '^' marker.
    Has the command changed for this model / version? It works fine on ASA5505's running 8.4(5).
    Thanks for your time,
    John

    hi john,
    the show mac-address-table command should be valid.
    check if you've got MAC learning enabled on the ASA interface using show mac-learn command.
    edit: could you post show firewall? the above command works on transparent firewall only.

  • Show mac-address-table

    Given the command show mac-address-table from the privilege exec mode in a cat 2950, the output shows some (i think 4) mac-address tha are system. Do u have any idea what are these mac?

    Hi Dimitris,
    Thanks for writing in. I tried the command on my switch and got the following: Do you see a similar output and is this what you are referring to?
    2950#sh mac-address-table
    Mac Address Table
    Vlan Mac Address Type Ports
    All 0009.7c70.f9c0 STATIC CPU
    All 0100.0ccc.cccc STATIC CPU
    All 0100.0ccc.cccd STATIC CPU
    All 0100.0cdd.dddd STATIC CPU
    0100.0ccc.cccc is used for CDP/VTP/DTP/PAgP/UDLD
    0100.0ccc.cccd is used for PVST+
    0100.0cdd.dddd seems to be related to multicast, however need to confirm on this.
    0009.7c70.f9c0 is the mac address for my management vlan interface.
    2950#sh int vlan 1
    Vlan1 is administratively down, line protocol is down Hardware is CPU Interface, address is 0009.7c70.f9c0 (bia 0009.7c70.f9c0)
    Hope this helps.
    regards
    -Alok

  • Show Mac Address Table in ASR9k running XR

    I'm trying to find a Mac Address in the ASR9k table.  We have a server with multiple mac addresses and we need to know what MAC is being learned by what interface.
    Thank you,

    Use the command
    show l2vpn forwarding bridge-domain <group_number>:<domain_name> mac-address location 0/x/CPU0
    or
    show l2vpn forwarding bridge-domain mac-address location 0/x/CPU0

  • Sh arp does not show mac address of IP --- ASA

    Hi Everyone,
    I can ping the IP from the ASA but when i do sh arp it does not show me mac address od that IP.
    Need to know the reason behind this.
    Regards
    MAhesh

    So your ASA should have a route on the inside interface to internal networks. The address of that next hop in the routing table is the one you should have in your arp table allowing you to reach non-directly-connected (subnet-wise) hosts within the scope of that route statement.
    Think through the logic - ASA pings a host. It needs to determine proper egress interface. It checks and asks "Is it reachable via a directly connected interface (most preferred route)?" Answer no. "Do I have a route statement telling me how to get to it?" Answer yes (otherwise use default). OK - so ASA sends packet out egress interface defined in that route statement to the next hop as defined in route statement and waits for reply.

  • Restrict printing via MAC address

    I am currently using Mac OS 10.2 server and now we are considering upgrading to 10.4 because of better printer servers. We don't current use the server software for printer serves. We would like to have the ability to restrict printing to the printer via the computers MAC address. Is this possible via server 10.4?
    Thanks in advance
    Jason
    PowerG4 dual G4 - 400mhz   Mac OS X (10.2.x)   OS 10.2 server

    You could use the firewall to block certain IP addresses from printing.
    You can ensure certain computers receive consistent IP adddresses via DHCP using Server Admin > DHCP > Settings > Static Maps which depends on MAC addresses.
    hth,
    b.

  • Cat 2960 shows mac address port as "Drop"

    Hi all
    I am configuring a Cat 2960 port for connecting a VOIP phone, authenticated by MAB.  On connecting the phone, I get the port authenticated and assigned to the correct VLAN, with LLDP-MED advertising the correct voice vlan.  However, I then see no traffic from the phone on the switch.  I can see the MAC address of the phone is learned in the right VLANs, but the mac address is showing as "Drop", which normally means the address is statically configured to be blocked.  There is no static mac address table blocking configured on the switch.   Can anyone suggest why this is happening?
    Switch Version
    Switch Ports Model              SW Version            SW Image
    *    1 50    WS-C2960-48TC-L    15.0(1)SE3            C2960-LANBASEK9-M
    Port configuration
    interface FastEthernet0/1
    description "Standard user port"
    switchport access vlan 9
    switchport mode access
    network-policy 1
    no logging event link-status
    srr-queue bandwidth share 5 10 40 55
    priority-queue out
    authentication host-mode multi-auth
    authentication order dot1x mab
    authentication priority dot1x mab
    authentication port-control auto
    authentication timer reauthenticate server
    mab eap
    mls qos trust dscp
    no snmp trap link-status
    macro description vanilla_port
    dot1x pae authenticator
    dot1x timeout tx-period 3
    dot1x timeout supp-timeout 3
    spanning-tree portfast
    end
    LLDP-MED network-policy
    network-policy profile 1
    voice vlan 835
    Authentication (debug radius) result
    Jul 30 11:42:19.600: %AUTHMGR-5-START: Starting 'mab' for client (0004.f297.6668) on Interface Fa0/1 AuditSessionID 0AF0042200000063616A0592
    Jul 30 11:42:19.650: %MAB-5-SUCCESS: Authentication successful for client (0004.f297.6668) on Interface Fa0/1 AuditSessionID 0AF0042200000063616A0592
    Jul 30 11:42:19.650: %AUTHMGR-7-RESULT: Authentication result 'success' from 'mab' for client (0004.f297.6668) on Interface Fa0/1 AuditSessionID 0AF0042200000063616A0592
    Jul 30 11:42:20.682: %AUTHMGR-5-SUCCESS: Authorization succeeded for client (0004.f297.6668) on Interface Fa0/1 AuditSessionID 0AF0042200000063616A0592
    Resulting Switchport config - voice vlan is 835
    CLBdg640Test-AS2960-0#show int fa0/1 switchport
    Name: Fa0/1
    Switchport: Enabled
    Administrative Mode: static access
    Operational Mode: static access
    Administrative Trunking Encapsulation: dot1q
    Operational Trunking Encapsulation: native
    Negotiation of Trunking: Off
    Access Mode VLAN: 9 (NATIVE-DISCARD)
    Trunking Native Mode VLAN: 1 (default)
    Administrative Native VLAN tagging: enabled
    Voice VLAN: 835 (VOICE)
    Administrative private-vlan host-association: none
    Administrative private-vlan mapping: none
    Administrative private-vlan trunk native VLAN: none
    Administrative private-vlan trunk Native VLAN tagging: enabled
    Administrative private-vlan trunk encapsulation: dot1q
    Administrative private-vlan trunk normal VLANs: none
    Administrative private-vlan trunk associations: none
    Administrative private-vlan trunk mappings: none
    Operational private-vlan: none
    Trunking VLANs Enabled: ALL
    Pruning VLANs Enabled: 2-1001
    Capture Mode Disabled
    Capture VLANs Allowed: ALL
    Protected: false
    Unknown unicast blocked: disabled
    Unknown multicast blocked: disabled
    Appliance trust: none
    LLDP neighbor info showing voice vlan 835
    CLBdg640Test-AS2960-0#sh lldp neighbors fa0/1 detail
    Chassis id: 0.0.0.0
    Port id: 0004.f297.6668
    Port Description - not advertised
    System Name - not advertised
    System Description - not advertised
    Time remaining: 3558 seconds
    System Capabilities: T
    Enabled Capabilities: T
    Management Addresses - not advertised
    Auto Negotiation - supported, enabled
    Physical media capabilities:
        100base-T2(HD)
        100base-TX(FD)
        100base-T4
        10base-T(FD)
    Media Attachment Unit type - not advertised
    Vlan ID: - not advertised
    MED Information:
        MED Codes:
              (NP) Network Policy, (LI) Location Identification
              (PS) Power Source Entity, (PD) Power Device
              (IN) Inventory
        Inventory information - not advertised
        Capabilities: NP
        Device type: Endpoint Class III
        Network Policy(Voice): VLAN 835, tagged, Layer-2 priority: 5, DSCP: 46
        PD device, Power source: PSE, Power Priority: High, Wattage: 6.5
        Location - not advertised
    Total entries displayed: 1
    MAC address table showing "Drop" port for learned address in VLAN 835
    CLBdg640Test-AS2960-0#sh mac address-table address 0004.f297.6668
              Mac Address Table
    Vlan    Mac Address       Type        Ports
       9    0004.f297.6668    STATIC      Fa0/1
    835    0004.f297.6668    DYNAMIC     Drop
    Total Mac Addresses for this criterion: 2

    Thanks for updating the problem raarons!

  • NAM shows MAC address instead of IP address in host

    Hi,
    Product: Cisco Prime NAM Appliance 2304
    Version: 5.1(3)
    Problem: We only can see MAC address on Hosts table in NAM, not IP address.
    Does anyone know what happen and how to fix it?
    Thanks!!!

    I wouldn't worry too much about the address shown in the Remote Management tab.  The ARDAgent process, which is what is listening on his computer for connections from Remote Desktop, binds to all active network interfaces and ultimately that's all that matters. Of out curiosity though, to what IP address does the "unknown-b8-8d-##-##-##-##.home" dns name resolve?  Is it the WAN address?  I can't imagine it resolves to a private address like a 192.168.
    In any event, let's focus back on the network structure. Does the BT router have both a hard wired LAN ethernet port as well as a WiFi radio for LAN connections?  My guess is yes. I am also assuming that he does *not* have another router attached to the BT LAN ethernet port like an Airport basestation that is serving the WiFi connections.  Typically, the LAN ethernet port is given, via DHCP, a real Internet accessible address but the addresses served via DHCP for wireless clients are private network addresses only.  It's seems unlikely to me that the router is automatically forwarding incoming connections to a private network address on the WiFi network.  But if he plugs his Mac in to the ethenert LAN port on the BT router then you should be able to connect directly to the address given to it via DHCP because it *should* be a real Internet accessible address.

  • Dladm does not show mac address for aggr

    All,
    When I run dladm show-aggr for my two aggr interfaces, I have one not displaying its MAC. Anyone a clue how I can get this sorted?
    key: 2 (0x0002) policy: L2      address: 0:14:4f:da:13:e8 (auto)
               device       address                 speed           duplex  link    state
               nxge2        0:14:4f:da:13:e8          1000  Mbps    full    up      attached
               nxge3        <unknown>         1000  Mbps    full    up      attachedCheers,
    Davy
    Edited by: Davy_S on Apr 18, 2009 1:52 AM

    I had the same problem. SUN support recommends latest kernel patches. That solved my problem.

  • CSCui55504 - show Mac address table from RP gives an error msg and40;but from SP works )

    Hello Cisco,
    Is there any updates or ETA regarding this bug, as our production 6500 core switch is experiencing this issue and viewing mac-table is a critical activity we perform everyday to troubleshoot client connections.

    I'm having this same issue. I also have this line in my log, which is curious:
    12/14/14 7:13:07.822 PM netbiosd[16766]: Attempt to use XPC with a MachService that has HideUntilCheckIn set. This will result in unpredictable behavior: com.apple.smbd
    Is this related to the problem? What does it mean?
    My 2010 27" iMac running Yosemite won't wake up from sleep.

  • Attempt to obain MAC address on Deskjet 3510 printer

    Please tell me where to find the MAC address for HP Deskjet 3510.  Am attempting to wirelessly attach to tethered network using (legally) phone as connector.  Number did not print out on "Print Status Report". Thank you.

    Hi dbqueen,
    Welcome to the HP Forums.
    I see that you are looking for your MAC address for your HP Deskjet 3510 printer.
    Please take a look through this guide. Printer Does Not Maintain Wireless Connection. Solution One shows how to print the wireless report. This will show your printer's MAC address.
    Hope this helps, and have a great day.
    RnRMusicMan
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to say “Thanks” for helping!

  • Mac address table on a PIX

    What am i missing?
    pixfirewall# show mac-address-table
                       ^
    ERROR: % Invalid input detected at '^' marker.
    [EDIT: karat is under the A in mac ]
    pixfirewall# sh ver
    Cisco PIX Security Appliance Software Version 8.0(4)
    Device Manager Version 6.1(3)
    Compiled on Thu 07-Aug-08 19:42 by builders
    System image file is "flash:/image.bin"
    Config file at boot was "startup-config"
    pixfirewall up 175 days 11 hours
    Hardware:   PIX-525, 256 MB RAM, CPU Pentium III 600 MHz
    Flash E28F128J3 @ 0xfff00000, 16MB
    BIOS Flash AM29F400B @ 0xfffd8000, 32KB
    0: Ext: Ethernet0           : address is 000d.28f9.62a5, irq 10
    1: Ext: Ethernet1           : address is 000d.28f9.62a6, irq 11
    2: Ext: Ethernet2           : address is 000d.8810.a620, irq 11
    3: Ext: Ethernet3           : address is 000d.8810.a621, irq 10
    4: Ext: Ethernet4           : address is 000d.8810.a622, irq 9
    5: Ext: Ethernet5           : address is 000d.8810.a623, irq 5
    Licensed features for this platform:
    Maximum Physical Interfaces  : 6
    Maximum VLANs                : 25
    Inside Hosts                 : Unlimited
    Failover                     : Disabled
    VPN-DES                      : Enabled
    VPN-3DES-AES                 : Enabled
    Cut-through Proxy            : Enabled
    Guards                       : Enabled
    URL Filtering                : Enabled
    Security Contexts            : 0
    GTP/GPRS                     : Disabled
    VPN Peers                    : Unlimited
    This platform has a Restricted (R) license.
    Serial Number: 807234146
    Running Activation Key: 0x6ab205ba 0x986d4239 0xf56523af 0x76f3d58b
    Configuration last modified by enable_15 at 12:58:08.130 EDT Thu May 16 2013
    pixfirewall# show mac-address-table
                       ^
    ERROR: % Invalid input detected at '^' marker.

    Hi,
    Command Modes The following table shows the modes in which you can enter the command:
    Command Mode
    Firewall Mode
    Security Context
    Routed
    Transparent
    Single
    Multiple
    Context
    System
    Privileged EXEC
    Source:
    http://www.cisco.com/en/US/docs/security/asa/asa80/command/reference/s4.html#wp1448364
    - Jouni

Maybe you are looking for

  • Unable to form af:table in navigation Menu Model

    Hi, Am using jdeveloper 11.1.2.1.0, I have developed my project with reference to the link below http://www.youtube.com/watch?v=cInX_FMZJaQ Am unable to drag and drop a VO as af:table in my jspx pages. Could any one pls explain me where i went wrong?

  • Digital Signature/Unknown Publisher

    So I was trying to download iTunes 10.5. The first time I did it a "digital signature" message popped up and then retarted the download, but it popped up again. I went on to this discussion board to find some help. Some discussions said to delete (re

  • XPath to Update XML document

    Using XPath I can read a particular node of an XML document through JAVA program. However, is it possible to Update the value of the node, just read from XML doc, using XPath expressions ?

  • Recommend a USB Wi-Fi Adapter

    I'm trying to find an inexpensive USB Wi-Fi Adapter. Trying to find ones that are mac compatiable is proving to be difficult. Can you recommend a 'b' spec USB wi-fi adapter for under $20? Thanks.

  • How to create new file association

    Hello, I have a program that uses the .pez file extension. Now I want to change the association so that it is opened with my desired program. Therefore I tried: xdg-mime default prezi-desktop.desktop application/pez However, this does not work. The .