Printer will not work: error code 0xc19a0022

Hello citizenED,
Welcome to the HP Forums.
I see that you are getting the error code " 0xc19a0022 " .
I do have a few steps that we can try.
First off, please make sure that you have the printer power cable connected directly to a wall outlet and not a power bar/strip. Here is a document that uses a LaserJet printer as an example but it is meant for HP products in general. Please click on the following link that explains the Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector.
I have also located a document that deals with a 'Problem with Printhead,' 'Printer Failure,' 'Ink System Failure,' or a '0x...' or a 'C2...' Error ...
If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here: click here.
Thanks for your time.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

Similar Messages

My ITunes will not work error code 2503

window XP cannot uninstall ITunes. ITunes will not operate. error code 2503

Hello, bearbassman.
Thank you for visiting Apple Support Communities.
Here are the steps I would recommend going through when receiving this error.
iTunes 11.1.4 for Windows: Unable to install or open
http://support.apple.com/kb/TS5376
Cheers,
Jason H.

I upgraded from leopard to lion and my epson printer will not work. I get a communication error

I upgraded from leopard to lion and my Epson printer will not work. I get a error message comunication error. What can Ido to fix this I bought a new USB cord and it did no good.

I suddenly had the same thing happen. I've had my new iMac for 3 months and at first my Epson Artisan 50 worked okay then yesterday I started getting the same error message other people on this support site have gotten. I tried ALL the advice given (deleating the Epson files from the library folder, etc. reinstalling older software) and nothing worked. With the newest iMac (and operating system) you cannot pick and choose which version of Epson software you want. You must use the 10.8 version or it simply will not open when you've downloaded it. Finally I found the comment above by den.thed and tried the OS X Mountain Lion: Reset the printing system suggested. As much as I hated to lose all my printing presets that took a lot of expiermentation to set up, I was desperate. I tried it and it worked. Now I just have to consult my old computer and try to recreate all my printing set ups. So to others with Epson / Apple 10.8 issues this may help when everything else fails. Thanks den.thed for your advice.

Printer will not work after update to Mavericks

I have a macbook pro and an HP7280 printer connected wirelessly. After upgrading to Mavericks the printer will not work. The first time I used it the system upgraded automatically (I forget what it said but it just went ahead and did some upgrading) When I clicked on something to print it did recognized the printer but just scrolled and scrolled and never printed. So I deleted the printer and reset the system and then added the printer back on - same thing. Any ideas??

It means there is no issue with the driver you are using and with it working correctly on Mavericks. So you have a network issue with the printer queue you are using. Normally a reset of the printing system and re-adding the printer would be enough to get things working again. But since you have done this and your issue is not resolved, there must be some other gremlins in the system.
With the HP connected to the network, if you know its IP address you can enter this as a URL into a web browser. This should result in you connecting to the internal web page of the HP. Does this work?

HP-2840 needs new drum (Q3964A) and I am told my printer will not work when I install a new drum

My HP2840 laser jet All-InOne has been telling me for 6 months that I need a new drum. I was waiting until I saw an issue with my print quality (which I never had a problem) and now my printer will not work unless I replace the drum.
A friend told me that even after installing a new OEM drum, that my printer will still not work unless I call HP and pay for them to tell me how to make it work.
Is that true?
I need help fast cause now my wife is really angry that I "broke" the printer!
Thanks in advance!

mmcnel01 wrote:
Is this an official HP forum?
If so, is there anyone from HP - maybe a moderator or someone, that will respond to my question?
This is a user to user forum and is not an official link to HP support. I would suggest that you contact HP as shown here.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

HT4623 my i phone will not work error 3194

My Ipnone will not work error 3194

Well, right now, Apple is getting loads of people who are trying to download the new update. My iPod is doing the same thing, so, just wait an hour or two and then try again. It may take a while to veryify the update, and even longer to actually download it. Some people at my school updated their OS in study hall, while others were having the same problem you were. It should be fixed soon, just relax...

Since upgrading to OS X yosemite my printer will not work.

Since upgrading to OS X Yosemite my printer will not work.

I found the solution in another thread. Thanks to frankglyn who posted it there.
I've just copied it here, as this seems to be the most active thread on this subject.
The solution (steps A to C) worked fine for me and others and should work for you as well, until Kodak will come with an updated driver. Then, you can revert the changes as also described below (steps 1 to 7)
A) in Spotlight Type Terminal and then press enter.
This should bring up the terminal window/program.
B) In the Terminal type sudo sh -c 'echo "Sandboxing Relaxed" >> /etc/cups/cups-files.conf'
It will ask for your password.
C) After that type following: sudo launchctl stop org.cups.cupsd
After that if you are lucky the printer driver should start to work. (which it did in my case)
I hope this works out for you, if not then you can do following to revert the changes:
In case you want/have to revert the changes:
1) Open the terminal as usual (Spotlight type Terminal hit enter and wait for the terminal window to appear)
2) then type: cd /etc/cups
3) then type: sudo nano cups-files.conf
4) 'type in your password'
This brings up a command line editor which you can use to edit the file
5) Remove the last line which says Sandboxing Relaxed
6) press 'ctrl x'
And then confirm with y when being asked if you want to save the changes
7) after that type sudo launchctl start org.cups.cupsd

CLIENT_TEXT_IO.fopen will not work Error

I keep getting the following -
WebUtil Error: oracle.forms.webutil.file.FileFunctions bean not found. CLIENT_TEXT_IO.fopen will not work.
Nothing I have found on any forum threads has helped me resolve this issue. I believe it has to do w/ configuration. The error occurs in my Development Suite environment I have set up on my laptop. The webutil set up on the Application Server seems to be fine.
I've checked both default.env and formsweb.cfg and both seem to be set correctly. I have the webutil.pll attached to the forms and the webutil.olb in the object library.
I'm using WebUtil 1.0.6 on Oracle 10g (9.0.4).
If anyone has any guidance on this issue, your help is appreciated.

The error isn't obvious. The Java Console outputs the following. I went through the webutil docs again and still didn't get the issue resolved. Can you help?
Oracle JInitiator: Version 1.3.1.17
Using JRE version 1.3.1.17-internal Java HotSpot(TM) Client VM
User home directory = C:\Documents and Settings\localadmin
Proxy Configuration: no proxy
JAR cache enabled
Location: C:\Documents and Settings\localadmin\Oracle Jar Cache
Maximum size: 50 MB
Compression level: 0
Loading http://server.domain.com:8889/forms90/java/f90all_jinit.jar from JAR cache
proxyHost=null
proxyPort=0
connectMode=HTTP, native.
Forms Applet version is : 9.0.4.0
java.lang.ClassNotFoundException: java.io.IOException: open HTTP connection failed.
     at sun.applet.AppletClassLoader.getBytes(Unknown Source)
     at sun.applet.AppletClassLoader.access$100(Unknown Source)
at sun.applet.AppletClassLoader$1.run(Unknown Source)
at java.security.AccessController.doPrivileged(Native Method)
     at sun.applet.AppletClassLoader.findClass(Unknown Source)
     at sun.plugin.security.PluginClassLoader.findClass(Unknown Source)
     at java.lang.ClassLoader.loadClass(Unknown Source)
     at sun.applet.AppletClassLoader.loadClass(Unknown Source)
     at java.lang.ClassLoader.loadClass(Unknown Source)
     at java.lang.ClassLoader.loadClassInternal(Unknown Source)
     at java.lang.Class.forName0(Native Method)
     at java.lang.Class.forName(Unknown Source)
     at oracle.forms.handler.UICommon.instantiate(Unknown Source)
     at oracle.forms.handler.UICommon.onCreate(Unknown Source)
     at oracle.forms.handler.JavaContainer.onCreate(Unknown Source)
     at oracle.forms.engine.Runform.onCreateHandler(Unknown Source)
     at oracle.forms.engine.Runform.processMessage(Unknown Source)
     at oracle.forms.engine.Runform.processSet(Unknown Source)
     at oracle.forms.engine.Runform.onMessageReal(Unknown Source)
     at oracle.forms.engine.Runform.onMessage(Unknown Source)
     at oracle.forms.engine.Runform.sendInitialMessage(Unknown Source)
     at oracle.forms.engine.Runform.startRunform(Unknown Source)
     at oracle.forms.engine.Main.createRunform(Unknown Source)
     at oracle.forms.engine.Main.start(Unknown Source)
     at sun.applet.AppletPanel.run(Unknown Source)
     at java.lang.Thread.run(Unknown Source)

HP Photosmart C6180 All-in-One printer will not work

Printer worked one day and the next day it did not and now will not turn on. I did not turn it off. It went off all by itself. Only 3 years old and not over used. Have checked outlet and power cable. Green LED light comes on when connected to outlet but as soon as I connect it to the printer, the light goes out and the printer will not turn on. Is it dead?

I have the exact same problem
Where do we find a solution

Ipod touch stuck in recovery mode and will not restore. error code 3194

ipod touch stuck in recovery mode, will not restore and comes up with error code 3194, itunes is up to date, please help

Hi @rchangel - Thanks for the ideas...
Yes - it won't let you install the 32 bit version on a 64 bit machine.
I've had a cursory look at the SP1 release notes, and couldn't spot anything vital - what critical stuff do you know of in SP1?
I don't want to have to go through all the pain of setting up VM's, reinstalling iTunes, getting all my album art back in etc. (though I could, as I do have Win7 pro). I've also heard that running iTunes in Windows 7 compatibility mode might help. Can anyone confirm whether that actually works?
I think it's in Apple's gift to fix this issue, given that they say that they support Windows 7. So far I've had no feedback from a mail I sent to Apple, and the number of users reporting this problem keeps going up and up.
I want Apple to recognise that there is a problem, and then I want them to fix it.

Frozen ipod after new updates, will not recover, error codes 1601 and 1602

i updated my ipod last night, was working fine, turned off, then on again this morning. was working fine this morning for a while, then went completely blank, will not start up, just completely dead. i have tried to restore,several times and get error code 1601, and 1602. have tried restarting my computer,checking for updates, restarting my itunes, using another computer, tried another lead, and everything else suggested by support. it will just not do anything. has anyone got any suggestions, please.

I would suggest that you put your iPod into the recovery mode and restore it. Next time something like this, it is better to start with the more basic troubleshooting steps first before trying to restore. The two easiest are restart and reset.
Try these steps with your touch.
1. Unplug the device from your computer
2. Turn the touch off - hold the Sleep/Wake button down until you see the red slider and turn the device off. Note: this may not work. If not, go to the next step.
3. Start iTunes
4. Hold the Home button down and keep holding it down while you plug your iPod back into your computer.
5. Keep holding the button down until iTunes tells your "that an iPod in Recovery mode has been detected".
6. Let go of the button and follow the on screen instructions to restore the touch.

Satellite P200-1FC: CD/DVD drive will not start - error Code 10

My Satellite P200-1FC was purchased in January 2008 and preloaded with Vista Home Premium. The DVD/CD Drive is listed in device manager as "TSST corp CDDVDW TS-L632H ATA Device".
At first the drive worked perfectly, but has recently refused to start. Device manager now shows it with a yellow exclamation mark and it's status is given as "This device cannot start. (Code 10)".
Clicking check for solutions produces "could not load driver software" but no solution.
Searching similar questions in user forums suggests a use of a Microsoft Help & Support page headed "The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista".
However this involves modifying the registry! As a relative novice I am reluctant to do this unless I can find no easier way.
Must I bite the bullet and and enter this minefield, or is there a better way?

>At first the drive worked perfectly, but has recently refused to start. Device manager now shows it with a yellow exclamation mark and it's status is given as "This device cannot start. (Code 10)".
This error is definitely caused by a wrong registry entry.
I had such error several times ago and I have solved it removing the lower and upper filters from these registry key:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\{4D36E965-E325-11CE-BFC1-08002BE10318}
Here are some steps how it worked on my Windows system;
- I removed the CD/DVD drive from the device manager
- Then edited the registry as described above
- Rebooted the notebook
Im sure it will help you too.
Bye

Deskjet Ink Advantage 3525 - WiFi settings not working, error code 0XB808DE

Welcome all
When I enable and try to setup up a wireless connection with my printer a error message appears.
Error code is 0XB808DEDE (or capital o instead of zero in the beginnig)
When I turn off the wireless module printer function normally, priting only from USB connection.
I've try reset to the factory defaults settings and unplugging power cable for 60 seconds to hard reset the printer.
No ideas left.
My region is Europe - Poland.
Best wishes
Kamila

Welcome to the HP Community @Namilka ,
I understand you are noticing a "0x" error code on your Deskjet Ink Advantage 3520, and I wanted to reach out. Normally the error message means that the printer is experiencing an Ink System Failure, Printer Failure, or a failure with the printhead. As you have already tried resetting the printer and the error comes back, I would next recommend contacting HP directly at the information below to see about a replacement unit.
Reach our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region. http://www8.hp.com/us/en/contact-hp/ww-contact-us.html
Best wishes to you
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

DVD burner not working Error code 0x80020022 & 0x8002006E

When I try to burn a DVD I get the following errors . (Error code 0x80020022) & (0x8002006E)
When I put a dvd movie in it will show on the desktop and play in dvd Player.
It will show a CD in the finder and will play it in the finder and in iTunes. iTunes is can also burn CD.
I have brunt some dvds in the past month but it was hit and miss. Now I can not burn any dvds.
I booted up my iMac from my MacBook when I go to burn the dvd I get the same error. So now I'm not to sure if it is a software issue. I have also done a restart while holding P & R "option & Apple" to reset the Pram.
I'm going to erase the HD tonight and reinstall OS 10.5 to see if that fixes the problem.
If there is anything more I can do please let me know. I dont mind replacing the Supper Drive but I dont want to spend the money if that is not going to fix the problem.

I keep getting this code come up when i try to burn 0x80020022. My imac is 8 months old, and after looking on mac forums the only thing that seems to work is to go in and play around with the international system prefs. It will then burn a CD, although very slowly. A week later I go to burn a cd and this happens again! This surely can't be right with an 8 month old machine, and does this mean my DVD drive is going to die soon? I can't keep having to adjust the prefs every week.
Does anybody have any answers?
Cheers

Latest update for creative cloud will not install error code 1 HOW TO FIX THIS????

I CAN NOT GET cc UPDATE STALLS AT 43% AND GIVES ((ERROR CODE 1 )) AS THE REASON??????

1) Open Control Panel and Navigate to Control Panel\Programs\Programs and Features .
Under Program and Features list, locate the option : Adobe Creative Cloud and uninstall the same.
2) Open C:drive and navigate to C:\Program Files (x86)\Common Files\Adobe.
Open Adobe folder and delete folders named Adobe Application Manager and OOBE.
3) Navigate to C:\Program Files (x86)\Adobe.
Open Adobe folder and if present delete Adobe Creative Cloud folder.
4) Press Windows button (located between Ctrl and Alt buttons) along with R button together at a time , you will get a run command window.
Type in below command and hit 'Enter' key.
appdata
Then navigate to Local>Adobe.
Open Adobe folder and delete folders named AAMUpdater and OOBE.
5) Click on the below link and download Creative Cloud setup file and use the same to install the Creative Cloud Desktop application.
https://creative.adobe.com/products/creative-cloud

Printer will not work: error code 0xc19a0022

Similar Messages

Maybe you are looking for