Printing PO's using Crystal Report

Hi,
I am printing Purchase order using crystal reports. And when I print single PO, it is printing perfectly and I am printing one PO per page in pre printed stationery. But when I Print Multiple PO's i.e., mass printing, the first record gets printed correctly but when the printer scrolls to second page, the header section jumps one line above and when it scrolls to third page, it jumps two lines above and so on. And I am using continous stationery in dot matrix printer. How to print multiple PO's with Correct page header alignment. (Also I found the same problem when I print A/R Invoice).
Thnx in Advance.
Regards,
S Desikan

Dot matrix printer has the inherated weakness for linefeed control.
You have to change the page setting quite a few times before it can be fit.
If possible, laser printer will be much better. What you see is what you get.
Thanks,
Gordon

Similar Messages

Server error in printing in server using crystal report 2008 with VS2008

Hi,
We are using Crystal report 2008 in VS 2008. Everything working fine in local but when we deployed it in the server we are getting the below while print the report.
"An error occurred on the server. Printing will be stopped. Would you like to view the error information"
Anyhow the report is printing but I don't know why this error is occur and how to stop this. I had installed the CR runtime in the server. I dont know what is going wrong. The same we tested locally in a non crystal report installed PC.
Please help me to get rid out of this error.
Thanks
Natraj

Soemthing strange going on here.
Typically this Integrated vs Classic is an issue with images where Classic uses web.config tags between <system.web><httpHandlers><u2026 crystalimagehandler../></httphandlers></system.web>
Integrated uses tags between <system.webserver>u2026<handlers><..crystalimagehandler/></handlers></system.webserver>
Not sure why this would affect printing. Do you have tags that specifying where to download the printcontrol from? On the other hand, I would think that if images had anything to do with it, then you'd get red Xs when viewing. As far as I know, the printcontrol.cab doesnu2019t need to be specified in the <system.webserver> tags.
This one may be best resolved over the phone. Phone support can be obtained here:
http://store.businessobjects.com/store/bobjamer/en_US/pd/productID.98078100?resid=S6I@hgoHAkEAAGsiyVkAAAAR&rests=1282226845369
Ludek

Printing Extremely Slow Using Crystal Reports 2008 ActiveX Print Control

Problem:
We are trying to upgrade our existing Crystal Reports 10.0 ActiveX Viewer ASP based reports to the new Crystal Reports 2008 ASPX Report Viewer but are having print performance issues that have prohibited us from moving forward.
Environment:
Windows 2003 Server Standard Edition 32-bit with SP1
IIS 6.0 running ASP .NET version 2.0.50727
Crystal Reports 2008 SP0 with FP1
Crystal PrintControl.dll version 12.0.0.796 (verified on server and client)
Details:
Crystal Reports 2008 ASPX Report Viewer Object & ActiveX Print Control Report Printing Scenario
From a typical 27 page report, the user clicks the Print icon from the ASPX Report Viewer Object.
The Print window with the message Crystal Reports Print Control immediately appears on the screen. This window is on the screen for approx 30 seconds.
The Print Setup window finally appears on the screen. The user verifies the printer, chooses to print pages 1-5, and clicks the Print button from the window.
The Retrieving page 1 message appears in the Print window. The message remains in the window for approx 30 seconds.
The Printing page 1 message appears in the Print window. The message remains in the window for approx 30 seconds.
The Printing page 2 message appears in the Print window. The message remains in the window for approx 30 seconds.
The Printing page 3 message appears in the Print window. The message remains in the window for approx 30 seconds.
The Printing page 4 message appears in the Print window. The message remains in the window for approx 30 seconds.
The Printing page 5 message appears in the Print window. The message is in the window for less than 1 second.
After 3 MINUTES of waiting the report finally starts printing.
Crystal Reports 10 ASP ActiveX Report Viewer Report Printing Scenario
From the same typical 27 page report that was used in the Crystal Reports 2008 scenario, the user clicks the Print icon from the ASP ActiveX Report Viewer.
The Print window Immediately appears on the screen. The user verifies the printer, chooses to print pages 1-5, and clicks the Print button from the window.
The Print window Immediately disappears from the screen and the report Immediately starts printing.
The entire print process takes only 3 u2013 4 SECONDS.
Even though we are trying to get the users to decrease the amount of paper used in report printing. They still do a significant amount of printing. The difference between the print performance using Crystal Reports 10 (3-4 seconds) and Crystal Reports 2008 (3 minutes) is totally unacceptable to our users.
Has anyone else experienced this problem and is there a known fix for it? This is the only thing holding us back from our upgrade and it has become very frustrating to us.
Much thanks to anyone that can shed some light on this.

Hi Brian,
Please have a look at [this|Crystal 11.5 Activex control for viewer; post.
However, have you tried with the No Printer options available in Print Options window from designer?
Regards,
Atanu.

Print Draft Document using Crystal Report in SAP 8.8

I created a Crystal Report Layout using SQL View as data source for AR Invoice which prints out fine. (everthing on 1 page)
To print Draft Invoice, I copied the view to use ODRF/RDF1 instead of OINV/INV1, copied the Crystal report and updated the data source to the new view. When print Draft Invoice, it prints 3 pages - page 1 blank, page 2 just the "DRAFT" watermark, page 3 the crystal report without watermark.
Steps to print Draft Invoice: Sales-A/R > Sales Report > Document Drafts Report > Open selected Draft Invoice document > File > Select Layout and Print...
What is happening behind the scene when printing Draft documents? What is the correct way to print Drafts (e.g. special settings designing Crystal Reports)?
Thanks,
Grace

Thank you for your reply. It works in this specific report.
But we have both PLD and Crystal Report in the system, changing the settings means the PLD will lose their watermark...
Also, I don't know how the Draft is displayed, but when select Print Preview for Draft, it's asking for parameter (DocEntry), which I have setup a DocKey@ in Crystal Report and set it in the Selection Manager. Does SAP provide DocEntry in Draft Invoice (ODRF) the same way as in Invoice (OINV)?
Thanks,
Grace

Print layout designer using Crystal report

Hi Dear;
how can i create a print layout in crystal report instead of print layout designer
is any conversion of should i created from scratch?
from where can i download the crystal report templates?
regards;

Hi,
There is no conversion tool between these two reports. You have to create them from scratch.
Check these threads to find out more:
Sample Crystal Reports
Re: SAP Business One and Crystal Reports
Thanks,
Gordon

Using crystal reports to generate invoices

Post Author: samme
CA Forum: General
I'm writing a report for a client who wants to print multiple invoices using crystal reports. The invoice needs to sort in date order, one date and information associated with that date on each page. Each page has a subtotal since multiple items/services are linked ot one date. The last page of the invoice needs to have the total and should at the bottom of the page with the last subtotal. Not onlastrecord does not work because if the user prints multiple invoices, crystal doesn't see the "last record" until the last record of the last invoice.
The client wants the normal invoice information on the first page of the invoice: Company Logo, Customer Address, Company Info, Invoice #, Date, etc. as well as the column headers - quantity, unit of measure, price, etc.
On all other pages of the invoice, the client wants, the company logo, the invoice # and the column headers.
I have the report grouped by invoice number and then by a date formula. I cannot seem to get where I need to be with this invoice and have been working on it for some time. Can anyone give me some direction please.....
Thanks in advance!

On Sat, 15 Mar 2003 16:46:48 GMT, "Bill Bradley"
<[email protected]> wrote:
>I know. We thought that the Report Builder would be the way to go,
since
>ART didn't do too much for us. You guys poorly document it, and,
show no
>examples of using it to build a report. In addition, it'd be nice if
>SOMEONE would come up with a list of what tables show what. While
Novell
>may have a detailed list of things in the ZFD docs, it's pretty much
so
>detailed and complex that, it's next to useless. I've resorted to
doing
>huge dumps of things to a csv, then, using CR or Excel to generate
some kind
>of report.
>
>The whole process is not as easy as it should be, seeing that we paid
money
>to get a reporting vehicle.
>
>As comparison, SMS isn't any easier, but, there's more documentation
on it,
>so, when you're forced to roll your own report, it's a clearer
path...
I do understand, I'm not a programmer either :-(
the company who wrote report builder is Digital Metaphors, they have a
very good
training application and additional detailed information of how to
write
reports.
The CIM schema is I agree Cr** (well not easy) and without the detail
that
Novell provide it doesn't work.
I hope that a friend of mine is going to provide the compromise that
you and I
are looking for. Namely the ability to create the SQL queries that
ART can
make, with a simple report system. Keep an eye on caledonia.net for
an
announcement for ART4 (Derived from but unrelated to Salford
Software's
product) :-)
Tim
No Direct e-Mail Please!
Tim Heywood
Independent Consultant
Scotland
Novell Support Connection SYSOP
In theory, practice and theory are the same,
In practice they are different!

Print Preview using crystal report in SAP B1 slow.

Dear all,
I face another problem. Print preview using crystal report in SAP B1 is very slow. Although i have create a query view in SQL server but it's still slow for my user. First time i create using table in crystal report. just drag the table. It's take more than 10 minutes. After that i move all the query to view in SQL server , it's take 1-2 minutes to print preview some time more.. But i think that it's still slow. Does any one know how to print preview fast. Just like in PLD.
Thanks in advance
bodhi86

Hello,
How do you answered to this question ?
Malika
Edited by: Malika Sanoune on May 13, 2011 1:48 PM

Print preview using crystal report in SAP B1 is very slow.

Dear all,
I face another problem. Print preview using crystal report in SAP B1 is very slow. Although i have create a layout in AR invoice form and applying the print sequences (ie 4 prints). Does any one know how to print preview fast. Just like in PLD.
Thanks in advance
Kamlesh Naware

Hi,
Basically Crystal report run with SQL statement, I would suggest to do well performance tuning on SQL query / Store Procedure.
Structure your query in DBA manner that will make some how faster such as use ( inner join, less condition,...)..
also if it simple query then use Command in Crystal report rather store Procedure..that make some how Faster your report.
Thanks
Kevin
Edited by: Kevin Shah on May 27, 2011 4:21 PM

Total No of pages different in report printed using Crystal Report XI R2 vs SAP Crystal Reports, developer version for Microsoft Visual Studio (File Version 13.8)

Currently in our application, we are using Crystal Report XI R2 for generating the reports. We are in the process of upgrading the Crystal Report to SAP Crystal Reports, developer version for Microsoft Visual Studio (File Version 13.8). I updated that on my machine and all the reports work fine. I didn't have to modify any of the reports.
However when comparing the reports, we found that there are few reports on which the total no. of pages differ from the report displayed using Crystal Report XI R2 vs SAP Crystal Reports, developer version for Microsoft Visual Studio (File Version 13.8). Comparing the reports, it looks all the data that were fit on one page earlier with version XI R2 doesn't fit on the same page with version 13.8, thereby increasing the page counts.
The fonts, page margins everything set on report itself. Nothing being set in the code.
Both the application is using the same report that is pulling the data from the same database. Our application is a web application.
Any suggestion, why this is happening.
Thanks.
Sanjay

I am not sure what is being compared here?
CRXI R2 designer to CRVS?
CR XI R2 in some version of .NET to CRVS?
CR XI R2 using RDC SDK to CRVS?
Also, is this happening on your development computer or after you deploy?
If you compare the the "Page setup" options dialog between reports that work and those that do not work, do you see any difference?
Is this a web or a win app?
Are you seeing the same issue when viewing and exporting - say export to PDF?
What is the printer driver used and it's version?
- Ludek
Senior Support Engineer AGS Product Support, Global Support Center Canada
Follow us on Twitter

Need alternative for activex print control using Crystal reports 2008

I have created a .Net web application (2.0/3.5 .Net framework) with crystal reports 2008.
Reports are viewed using Crystal reports 2008 activex viewer.
On click of PRINT icon in activex viewer, activex print control download prompt will be displayed on client machine.
I need to avoid downloading of activex print control on client machine. Is there any other alternative or option to use print functionality in viewer without downloading activex print control on client machine?
Or Is there any other workaround for print functionality in Crystal reports 2008 Viewer without downloading activex print control?
Note: Activex print control download prompt will not be displayed when using Crystal reprots XI Release 2 version.
Thanks,
Jagannath

Does anyone know which files need to be registered for the ActiveX print control? We occasionally have users who somehow break their Crystal ActiveX controls, and they can no longer see the print options. In Crystal 10, I was able to fix these issues by pushing a package which registered several files on the user's computer.

Print layout different with crystal report 2008 runtime

Hi,
I have reports which I print on a pre printed stationary. With Crystal report 11.5 run time it works fine.
Now I am using Crystal Report 2008 run time and with this I found that layout on the print is different than the actual layout in the design.
The print with CR 2008 run time is not exactly matching with the pre printed stationary. Whereas it is working fine with the 11.5 run time.
Can anyone please help?
Thanks,
Abhijit Gorhe

hi,
you can verify the settings
File -> Page Setup
- Printer Options
- Page Options
- Margins
Regards,
Vamsee

Deploy Visual Basic 6.0 RDC application using Crystal Reports 9 on Windows Vista

Post Author: albe
CA Forum: General
When attempting to deploy a Visual Basic 6.0 Report Designer Component (RDC) application using Crystal Reports 9 on Windows Vista systems, the application fails after the first print or preview (that show normally) and an error occurred: -2147417848 Method '' of object '' failed.
The app use the RDC and Active Data; I verify that the problem is encountered when the app calls the 'SetDataSource' method.
I tried everything that came in my mind: reinstalling it a few times, with administrator priviledges, disabling uac, manually registering dlls, ...
I hope that this will be fixed, since Crystal Report 9 is the last CR version compatible with windows 98.
thanks in advance,
Alberto

Hello,
This forum is for community use and is not considered a support site. For assistance you need to purchase a case from our support site. But 9 is no longer a supported version so this is your only place to get assistance.
Try downloading the only patches available from:
ftp://ftp1.businessobjects.com/outgoing/CHF/cr90actxwin_en.zip
ftp://ftp1.businessobjects.com/outgoing/CHF/cr90dbexwin_en.zip
ftp://ftp1.businessobjects.com/outgoing/CHF/cr90devwin_en.zip
ftp://ftp1.businessobjects.com/outgoing/CHF/cr90mainwin_en.zip
Thank you
Don

How to use Crystal Reports XI release 2 Preview with Lotus Notes Scripts ?

 Hi all, How to use Crystal Reports XI release 2 Preview with Lotus Notes 7 Scripts ? Thank's 

Hi,
we are using Lotus Notes and Crystal Reports for preview and printing reports from our Lotus Notes Applications. We use the RDC object model. For previewing the reports we export them in an pdf-file and then start the PDF Reader to show the Preview. This works fine.
But with Crystal Reports > 11 the RDC Object Model is no longer supportet, so we look for another way to preview and print our reports.
I try to preview a report build with crystal report XI release 2 in my thick client (Lotus Notes) using java reporting component JRC, this report uses an native xml file as datasource. If the datasource is saved with the report everything works fine, but otherwise I have the following error:
JRCAgent1 detected an exception: javax.xml.namespace.QName: method getPrefix()Ljava/lang/String; not found
I also tried the .jars from Crystal4Eclipse. Doesn't work. When I use Eclipse to view the report everything works fine. The class QName exitsts in the jaxrpc.jar and in the xbean.jar, but only in the xbean.jar a Methode getPrefix exists.
This is what we tried:
Works fine with RDC. Doesn't work with JRC until now.
Did this help you ?
Perhaps you con help me with the JRC, because I'm a java newbee so any ideas could be helpful.
Oliver
<a href="http://www.cominform.de">www.cominform.de</a>

Creating Employee Badges using Crystal Report.

Hi,
I have a requirement where i have to create Badges for Employees using Crystal Reports. The report is created but the issue here is when i generate the PDF output, apart from the portion of the rectangular Badge, there is lot of white spaces on the report and when i give it for printing, the entire PDF with white space is also coming up. I tried with resizing the crystal report but it did not worked. I want only the rectangular portion of the badge to come on the PrintPreview which can then be given for Print. Is it something to do with the print setting? I am using a special kind of printer(Evolis-Pebble) which is used to print badge cards.
Any help will be greatly appreciated.
Thanks,
Ashish.

Thanks Jayaprakash, we have asked for the installation of printer driver on the server machine where we design the report. Hopefully, we should get options to customize the report template to correct size as of the Badge size. Currently only default options are coming which doesnot allow us to use custom option to have the report to exact size of the Badge in the page setup.
Thanks,
Ashish.

Using Crystal Report to create reports from ABAP

Hello,
We are currently using Jetform as the designer for our outputs like Invoice, Order confirmation, etc.....
We would like to switch to Crystal instead, but don't really know where to start from.
- We already have crystal on our B/W instance
- The additional need for Crystal is in R/3, and would be triggered trough ABAPs.
What I am looking for. I guess, is the equivalent to when:
we call up smartforms from ABAP using the generated function modules
we call up sapscript from ABAP using the predefine function call (write_form open_form close_form, etc)
we call up Jetform using special control code along with the data, sent to a jetform configured printer
=> What kind of call would we then make to send data to Crystal Reports place holder and print them?
=> What kind basis set-up is needed to have to comunication between Crystal and SAP established?
Thank you in advance for yours hints

Hi,
You will likely be able to access the tables directly using the Opensql driver using Crystal Reports. I don't understand why you are assuming that an Infoset is necessary. Can you point me to the documentation that states that an Infoset is necessary?
In any case, if you want to create an Infoset, this is done in SQ02. You need to make sure that you belong to a user group in order for Crystal Report to see the infoset.

Printing PO's using Crystal Report

Similar Messages

Maybe you are looking for