Printout doesn't match preview

I'm printing a brochure on pages. The print preview looks good, but the printed page has two unwanted lines.

A blank document is still a template.
I guess you mean the two lines middle left and right?
In Pages:
Menu > View > Show Layout/Invisibles
also
Menu > Arrange > Section Master > Make Section Masters Selectable
Then zoom in and see if there is anything there.
Peter

Similar Messages

Photosmart Plus B209 printout doesn't match screen

I always have a problem when printing out images with my HP Photosmart Plus B209 All in One. For instance, I make 2 in x 2 in images for passport photos. I create the images in a digital editing program in a 2x2 size and then drop them into MS Word for printout. On the screen, the picture size shows as 2 in x 2 in, but when I print it out, the picture is closer to 2 1/16 inches x 2 1/16 inches. And if I print a borderless 8.5 in x 11 in and the image has a frame, often either one of the sides or the bottom of the frame is cut off some. I have tried Scaling, Not Scaling, Fit Image to Page, Print 100%. I also have this problem with Microsoft Publisher when printing a banner. Although the Print Preview shows perfect alignment, when I print them out they don't quite match. Does anyone know what I might be able to do to fix this problem? I always do a scan and alignment when I change my cartridges and the quality of the print is great, but it just doesn't seem to print at the right size. It's not off by much, but enough to ruin the effect of certain images. I'd appreciate any feedback that someone can give me on this. Thanks so much.

Page 7 of the manual only references WPA and not WPA2. I did search the manual for mention of WPA2 and did not find any. This indicates it does not support WPA2, so this could be an issue. However, this typically does not prevent the printer from seeing the network but only connecting to it.
While the wireless radio is more than likely functioning, it may be best to confirm it is working since it is not seeing the SSID. Go to setup>network> wireless network test.
Does it show anything as failed? If so, what items are marked?
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Image created is cropped, doesn't match preview

In creating any image size larger than 11x17, I get the same result. The document previews correctly, but the PDF image is cropped on the right and bottom. (The remaining area is white space.) I've attempted this by "adding" new page sizes under properties and by "creating custom page size" under Converter Advanced Options.
Searching help and the forum has returned only one document that seems like it might apply. There's a help doc on "Presets" that talks about Engineering Drawings. However, this doesn't show up under my settings options and the doc is totally inadequate in describing how to get to it. There's a reference to a location of "extras" in docs & settings, but it isn't there on my system and a search for the folder has come up blank for anything related to Adobe.
I've got a couple of hours invested in this and I'm pretty frustrated. Any help would be greatly appreciated. Thanks in advance.
Windows XP Pro / Acrobat Standard 8.1.2

I've got a couple of days invested in the same problem. The good news is that when you choose your file to be converted, if you will change the type of files box to just the file you want to convert (For example: change "all files" to "doc" files), a little settings box will come up on the right that will allow you to change the size of the pdf documents. The bad news is the pdf still converts to letter size, no matter what you put the settings at. If you find out what the problem is there, please post it.

Exports come out with blocky titles and shifting pixels, doesn't match previews.

OK i have 720x480 29.97 footage which I imported and dragged a clip down to the new item icon to make an appropriate sequence. I created titles which ended up looking blocky in the program monitor for some reason. I then made a 1280x720 sequence for the heck of it and it turns out the titles look fine in those in the program monitor. I went to export and it looked fine in the render preview as well, but the final export in 720 (480 footage placed into a 720 timeline and exported as 720 in BOTH 29.9 and 23.9) and titles looks horrible. So deos the video itself, the pixels are jittery (Expecially in a shot with roof shingles for example). I am looking at the export settings and have no idea what could be going on with this.
To add to this, I have actually exported version of this project in the past just fine. I am just doing something new to it and am now just facing these issues. I successfully exported all sorts of ways in the past.. I have brouhgt it into a sequence fit for the footage using the new item icon, and exported out as both 720 and 480 in 29.9 and 23.9, even burned to dvd in Encore and it played fine.
Im not wrapping my brain around how suddenly titles can look like blocky garbage in a 480 sequence, or why the render previews arent matching the actual output. any adivce here appreciated.

OK i have 720x480 29.97 footage which I imported and dragged a clip down to the new item icon to make an appropriate sequence. I created titles which ended up looking blocky in the program monitor for some reason. I then made a 1280x720 sequence for the heck of it and it turns out the titles look fine in those in the program monitor. I went to export and it looked fine in the render preview as well, but the final export in 720 (480 footage placed into a 720 timeline and exported as 720 in BOTH 29.9 and 23.9) and titles looks horrible. So deos the video itself, the pixels are jittery (Expecially in a shot with roof shingles for example). I am looking at the export settings and have no idea what could be going on with this.
To add to this, I have actually exported version of this project in the past just fine. I am just doing something new to it and am now just facing these issues. I successfully exported all sorts of ways in the past.. I have brouhgt it into a sequence fit for the footage using the new item icon, and exported out as both 720 and 480 in 29.9 and 23.9, even burned to dvd in Encore and it played fine.
Im not wrapping my brain around how suddenly titles can look like blocky garbage in a 480 sequence, or why the render previews arent matching the actual output. any adivce here appreciated.

Publish doesn't match preview

My .fla looks great. The preview .swf looks even
better. When I publish, the .swf file is all messed
up...transitions don't happen, text is missing....
BUT, strangely enough, a mac Projector works fine! What's
going on?

maliphant wrote:
>
Urami... thanks for the tip. Turns out I had both an
older and a newer
> version of Flash player. The new one play the .swf fine.
>
> Now I'm having problems with exporting the .fla as a
Quicktime Video. It
> pretty much is playing with the same funkiness the .swf
did. Any ideas?
Video is a frame by frame images sequence and not all flash
content will be exported
to that format unless design with it in mind from the very
beginning. For instance
Movie clips or some of the new features can't be exported. In
case of Movie clips,
you need to change their behaviors to graphic symbols so they
can play along the timeline,
tho won't if the timeline ends. There are many other things
to consider, let me paste
url to a site which describe all the Flash to Video aspects
in details.
http://www.flickerlab.com/flashtovideo/
Best Regards
Urami
!!!!!!! Merry Christmas !!!!!!!
Happy New Year
<urami>
If you want to mail me - DO NOT LAUGH AT MY ADDRESS
</urami>

Bounding Box Doesn't Match Object (Illustrator CS4)

I'm not sure if this is an error on my part or a bug, but for the last week or so, the bounding box for my objects hasn't actually matched the objects. This is really problematic when I try to transform the object using the bounding box handles.
On occasion, after I transform the object the bounding box will match it again and will transform correctly. Sometimes it will stay off. If it does reorient itself, undoing the transformations back the original size will cause the bounding box to reset back to it's mismatched state.
Things I have tried to resolve the issue:
Reset the Bounding Box
Copying and pasting the shape to a different document
Starting a new document from scratch (I thought it was possible I corrupted the file)
Return Keyboard Shortcuts to the Default
Restarting Illustrator
Restarting my System
To my knowledge, my system hasn't been updated in the last week nor has anything new been installed. However, IT does push out maintenance so there is a possibiltiy that it was updated and I don't know about it. The only programs open while working in Illustrator are Bridge, Outlook 2007, IE8, Explorer, InDesign CS4, Word 2007, Photoshop CS4, Acrobat Professional 9, Dreamweaver CS4, PowerPoint 2007, Previewer and possibly FireFox 3.something (though not necessarily all at once - generally about 7 of the above listed). My system runs XP Professional SP3 with an Intel Core2 Quad @ 2.66GHz and 3.25 GB of RAM. The objects are not grouped, do not contain clipping masks, do not contain transparency masks and are not compound paths. They are simple paths/shapes, often rectangles.
I have included some pictures to better explain my issue. This first image indicates how the bounding box doesn't match the rectangle.
The second image shows the process of transforming the shape via dragging.
The third image shows the result.
Thanks for any help you can provide!

Mr. Bugge:
Thank you for your response and I apologize for the delay in mine. I couldn't try all of the fixes immediately because I had to complete some job duties before I could tinker with this issue.
Things that did not work:
Closing Firefox
Clearing the Preferences
Moving the Preferences Folder
Deleting Temp Files
Closing Other Adobe Programs (Including Bridge Running in the Background
Things I cannot do for various reasons:
Re-installing Acrobat
Turning Off the Firewall (My Company Only Uses 1 Anyway)
Things I haven't tried yet but hope to try later:
Update Printer Definition or Change Default Printer
Check for Corrupt Fonts
Clear My Font Cache
Things I learned:
The issue is most easily recreated by transforming an object to a smaller object. However, zooming in will realign the bounding box but it will only stay aligned when zoomed in. I find it very curious.
Even if I don't end up finding an answer, I do appreciate your time and help.

[help] images colors doesn't match

Hello, when I place an image inside a new document the colors doesn't match with original.
For sample I save in tiff format from photoshop a rich black (70% 50% 30% 100%) when I place inside illustrator I get (86,01% 84,97% 78,95% 100%).
The color profile are syncronized and I use Europe General Purpose 2 (CMYK Coated FOGRA27 ISO12647-2:2004)

How do you know what values the bitmap image has in Illustrator? Did you pick up the color with the Color Picker? It's possible this originally picked up the value in RGB, and that got converted.
Does Illustrator have a CMYK separation preview such as InDesign, where you can measure the original TIFF values? If not, you can also save as PDF and examine that in Acrobat, using the Output Preview.

Closing Stock Valuation doesn't matched physicallly

Hi SAP Gurus.,
Can you please assist me reg this issue"Closing Stock Valuation doesn't matched physicallly".
May I know the possible rectification ways to solve this problem.
Thanks in Advance,
Regards,
Balaji Bhonsle

Physical Inventory...
http://www.sap-img.com/materials/physical-inventory-process.htm

Iphone 5 system serial no doesn't match with outer box? Case of misprint? i see only one latter is serial no doesn't match

I recently bought iphone 5 32gb white. Was surprise to see the outer box serial no doesn't match with iphone 5 system.
They have print XXXXXXTXXXX on box and on phone its XXXXXX7XXXXXX. Only one latter is mixprint though.
I check coverage status at apple site. The box serieal no is not found in apple system while the iphone 5 inside serial no i can see warrenty.
plz help is it normal to have serial no unmatched on phone and box or the phone is not genuine

You are correct. The SIM Tray of iPhone 5 does not have the Serial # printed on it. So your Serial # is the one in the Settings app About. This is your true Serial #. A 7 and a T from a box label are not distinct enough to matter. Apple will only honor the Settings About Serial # and the ones located inside the iPhone 5, which will be the same as the About Serial #.

Itunes will no longer accept any of my credit cards. Says security code doesn't match with any card I use. I have inputted new card info in the apple store area and it still says the same thing in itunes. Customer service is no help at all.

Itunes will no longer accept any of my credit cards. It says vcode doesn't match when it does. Customer service is no help. I have re-inputted the info in the account section of the apple store and in itunes--still says vcode doesn't match.

Itunes will no longer accept any of my credit cards. It says vcode doesn't match when it does. Customer service is no help. I have re-inputted the info in the account section of the apple store and in itunes--still says vcode doesn't match.

Error: The decapsulated inner packet doesn't match the negotiated policy in the SA

I upgraded my ASA from 8.2(1) to 8.4(3) as I wanted to try to get Android devices to properly connect via VPN.
After some effort, I was able to get the Android devices to connect via VPN. However, my syslog server has a number of errors recorded that look this this:
%ASA-4-402116: IPSEC: Received an ESP packet (SPI= 0x1E76EFA6, sequence number= 0x1F0) from x.x.x.x (user= testuser) to y.y.y.y. The decapsulated inner packet doesn't match the negotiated policy in the SA. The packet specifies its destination as z.z.z.z, its source as a.a.a.a, and its protocol as tcp. The SA specifies its local proxy as y.y.y.y/255.255.255.255/udp/42246 and its remote_proxy as x.x.x.x/255.255.255.255/udp/0.
Digging further, it seems this error might be due to a NAT issues with the VPN connections. VPN previously worked with Cisco's VPN client on Windows, though I did not test to see if that is no longer working. However, I made no changes in the config, except for those related to additions needed to support L2TP. With the below config, Android clients can connect to the ASA and access the internal network, but they cannot connect to external addresses. I'm at a loss.
The addresses used in the config: 192.168.1.0/24 are on the internal LAN and 192.168.3.0/24 are addresses assigned to VPN clients.
I noted in the config this line:
access-list inside_nat0_outbound extended permit ip any 192.168.3.0 255.255.255.0
The access list is not referenced anywhere, though it was referenced in the 8.2(1) config like this:
nat (inside) 0 access-list inside_nat0_outbound
I'm not sure what else changed, but I've looked over the config and I just cannot see what the issue might be. I'm hoping somebody might be able to point out my error.
Here's the config file (at least the parts that might be of interest):
: Saved
ASA Version 8.4(3)
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
boot system disk0:/asa843-k8.bin
object network obj-192.168.3.0
subnet 192.168.3.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
access-list outside_access_in extended permit icmp any interface outside time-exceeded
access-list outside_access_in extended permit icmp any interface outside echo-reply
access-list outside_access_in extended permit icmp any interface outside unreachable
access-list outside_mpc extended permit ip any interface outside
access-list inside_mpc extended permit ip 192.168.1.0 255.255.255.0 any
access-list testVPN_splitTunnelAcl extended permit ip 192.168.1.0 255.255.255.0 any
access-list inside_nat0_outbound extended permit ip any 192.168.3.0 255.255.255.0
ip local pool VPN-Pool-1 192.168.3.1-192.168.3.254 mask 255.255.255.0
ip verify reverse-path interface outside
nat (inside,any) source static any any destination static obj-192.168.3.0 obj-192.168.3.0 no-proxy-arp
object network obj-192.168.3.0
nat (outside,outside) dynamic interface
object network obj_any
nat (inside,outside) dynamic interface
access-group outside_access_in in interface outside
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANSP esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANSP mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANSP esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANSP mode transport
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 10 set ikev1 transform-set ESP-AES-128-SHA-TRANSP ESP-3DES-SHA-TRANSP
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
crypto ikev1 policy 5
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 10
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
group-policy testVPN internal
group-policy testVPN attributes
wins-server value 192.168.1.8
dns-server value 192.168.1.8 192.168.1.4
vpn-idle-timeout none
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value testVPN_splitTunnelAcl
default-domain value test.us
group-policy testVPNnsl2tp internal
group-policy testVPNnsl2tp attributes
wins-server value 192.168.1.8
dns-server value 192.168.1.8 192.168.1.4
vpn-idle-timeout none
vpn-tunnel-protocol l2tp-ipsec
group-policy testVPNns internal
group-policy testVPNns attributes
wins-server value 192.168.1.8
dns-server value 192.168.1.8 192.168.1.4
vpn-idle-timeout none
vpn-tunnel-protocol ikev1
username testuser password PASSWORD encrypted privilege 15
username testuser2 password PASSWORD nt-encrypted privilege 15
tunnel-group DefaultRAGroup general-attributes
address-pool VPN-Pool-1
default-group-policy testVPNnsl2tp
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
tunnel-group testVPN type remote-access
tunnel-group testVPN general-attributes
address-pool VPN-Pool-1
default-group-policy testVPN
tunnel-group testVPN ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group testVPNns type remote-access
tunnel-group testVPNns general-attributes
address-pool VPN-Pool-1
default-group-policy testVPNns
tunnel-group testVPNns ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group testVPNnsl2tp type remote-access
tunnel-group testVPNnsl2tp general-attributes
address-pool VPN-Pool-1
default-group-policy testVPNnsl2tp
tunnel-group testVPNnsl2tp ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group testVPNnsl2tp ppp-attributes
authentication ms-chap-v2
One last question: in order to get the connection from Android to work, I was forced to use "tunnel-group DefaultRAGroup". Is that actually a limitation, or did I make an error that forced that requirement? I wanted to use "tunnel-group testVPNnsl2tp".
Thanks!

Chris,
This is still a bit off the mark. I think I might be confusing the issue by including some of the VPN configuration that I had previously installed and working (e.g., two other VPN tunnel groups with split tunneling on one of them). Let's just remove that stuff from consideration. I actually tested the current configs just to see if they are working since the upgrade. testVPN is working with the split tunneling, but testVPNns (no-split tunneling) does not allow external access. I guess there is a NAT config issue there, too, but not sure what it is, yet. I've not investigated that closely.
I want to solve one problem at a time, though I understand there are some interdependencies.
What I'd like to focus on right now is just the L2TP VPN connection.
From what I've been able to understand from the documentation, what I need are these lines:
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANSP esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANSP mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANSP esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANSP mode transport
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 10 set ikev1 transform-set ESP-AES-128-SHA-TRANSP ESP-3DES-SHA-TRANSP
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
group-policy testVPNnsl2tp internal
group-policy testVPNnsl2tp attributes
wins-server value 192.168.1.8
dns-server value 192.168.1.8 192.168.1.4
vpn-idle-timeout none
vpn-tunnel-protocol l2tp-ipsec
tunnel-group DefaultRAGroup general-attributes
address-pool VPN-Pool-1
default-group-policy testVPNnsl2tp
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key P74bmqL6rT40bl5
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
crypto ikev1 policy 5
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
I still want to assign the IP addresses to VPN clients out of 192.168.3.0/24.
The tricky part is understanding exactly what NAT rules to insert and to avoid that error message I'm getting relatred to the encapsulated packets. I tried to introduce the commands you had, but it's missing stuff that I would need for L2TP/IPSec (e.g., "mode transport"). I also don't think I want "pfs group5". The above config "works" in that I get connected -- all negotiation is done. It's just that packets from the VPN client are not able to go out to the Internet and I'm seeing that encapsulation error messages when I try to send a packet.
Paul

HT1758 Are all Intel 24" iMacs w/Snow Leopard OK for Mountain Lion? My serial number doesn't match any of the one in the iMac ID list; they all start with "MA" or "MB", mine starts with a "W." Purchased direct from Apple August 2007.

Are all Intel 24" iMacs w/Snow Leopard OK for Mountain Lion? My serial number doesn't match any of the one in the iMac ID list; they all start with "MA" or "MB" and mine starts with a "W." Purchased direct from Apple August 2007.

Macs that can be upgraded to OS X Mountain Lion
iMac (Mid 2007 or newer)
MacBook (Late 2008 Aluminum, or Early 2009 or newer)
MacBook Pro (Mid/Late 2007 or newer)
MacBook Air (Late 2008 or newer)
Mac mini (Early 2009 or newer)
Mac Pro (Early 2008 or newer)
Xserve (Early 2009)
Open System Profiler and report what you find displayed for the Model Identifier.

Image in Lightroom doesn't match exported image viewed in Photoshop

After all my hard work in Lightroom, I export the image to a folder on my hard drive. When I open this exported image in Photoshop and view it alongside the Lightroom version of its "twin" in Lightroom, there is a significant difference. Why is this? I want to use these images in my books, but my time is wasted if I end up with anything other than what I created in Lightroom. Shouldn't these images match exactly?

Thanks Jao and Michael...the color management idea makes a lot of sense.
Adding to this idea, when I open the Pshop file I get a message about the doc having an embedded profile that doesn't match current RGB working space, and the usual 3 options: Use the embedded profile, Convert color to the working space, or discard embedded profile. No matter which option I choose, none of the opened docs match the Lightroom version.
The color balance is fine, but the colors aren't as vibrant. The Pshop photo is dull and lifeless compared to the Lightroom version. I used Clarity which added subtle brightness, and Vibrance to crank up the color in LR which added wonderful dimensionality and punch to the landscape scene, but the Pshop version has dulled these back down.

Bridge doesn´t show preview of tif-images

Hi,
I uses Bridge CS6 on a Mac with MacOS 10.9.2. Suddenly bridge doesn´t show previews of Tif-images. It´s also impossible to fill in any metadata. The program also says that the image isn´t tagged with any color profile. I don´t have these problems with jpegs, only with Tif-images. I even get previews on the RAW-images. Does anyone know what the problem can be?
Ulf

I guess I have to try to reinstall the program.......
I'm 99,99 % sure that won't help solving your problem because to possible being effective you also should use the Adobe Clean tool to get rid of a lot of the hidden files that just stay put during a normal reinstall. But if you want to do something easier instead of reinstall, quit Bridge and go to the user library (by default hidden per OSX 7, use Finder, menu Go with option to reveal this library)
In the preferences folder is plist file for Bridge (com.adobe.bridge5.plist), drag this file to the trash. Then in same library go to the folder Caches / Adobe/ Bridge CS5 and inhere delete both plug in and folder called Cache. (this means recaching the previews and thumbs).
Then restart Bridge holding down option key and again choose 'reset prefs'. All previous deleted items will be replaced with new, fresh and empty ones and you have an almost like factory settings Bridge without the need of reinstall.
But I really suspect it comes down to the Tiff files so maybe also a reset of preferences in PS might be worth a try.

I want to email a photo through iPhoto but it says I need a password... I entered my password but it says it doesn't match - what password do they want and how do I fix? (Facebook and other social media iPhoto posts work - just email asking for pass)

I want to email a photo through iPhoto but it says I need a password... I entered my password but it says it doesn't match - what password do they want and how do I fix? (Facebook and other social media iPhoto posts work - just email asking for password)

Your email password.
iPhoto '11: Email your photos
Open Mac Mail. From the Mac Mail menu bar click Mail > Preferences then select the General tab.
Make a selection from the: Default email reader pop up menu.

Printout doesn't match preview

Similar Messages

Maybe you are looking for