Printout of smartform
Want to take printout of a smartform from a local printer, help me out in configuring & getting printout successfully
Dear Bharath,
For your Question there are already many posts in SDN.
Few are given below.
http://scn.sap.com/thread/1485985
http://wiki.scn.sap.com/wiki/display/Basis/How+to+Configure+Printer+in+SAP
Please Search in SDN with keywords and you will find many appropriate answers.
Regards,
Sajid
Similar Messages
-
Messy code in printout of smartforms
Hi Gurus,
I encountered a problem when printing Thai characters using smartforms. it can be displayed OK on preview. but when I printed it out in the physical printer, all of the Thai characters are displayed as messy code like 'ŶµÄ½¨·¿¼ä°'. but English characters are displayed well.what should the prob be?
any responses would be awarded,
regards,
samsonCheck the character set attached with the device type of ur printer from SPAD. Check whether ur code page supports Thai characters or not. If it is ok then I think it is a problem within actual printer (may be the code page actually installed in it does not support Thai language)..better u can consult ur basis team.
Regards,
Joy. -
Smartforms Printing not coming properly in dot matrix printer
Hi Gurus,
We have implemented invoice printout using smartforms and required to use the dot matrix printer for printing.
We are now facing the problem on the printout from dot matrix is different from the preview we get in the system. But the printout from Laser Jet is coming out correctly for the same smartforms.
We are using EPSON DLQ3000 and we configure the output device using EPESCP2 as the Device Type. The problem is font size of the print out is all printed as courier size 12, but there are different font sizes in the smartforms.
But when we use local printing (using SAPLPD), there is no problem, all different font size is printed.
If we using to same output device to print some sapscript, everything is working well. Font size will print accordingly to the preview of the sapscript.
Do you have any idea of the problem that we have. Thanks for your help.
Regards,
Lee ShiDear Lee,
Ideally the printout should come as it is shown in the preview.I remember once it had happened with me too.But in my case there is no problem with the settings at SAP level.When we checked we found the problem is with the printer cartridge.
We co-ordinated with the system administrator and n/w guys.They in turn change the cartridge and issue was fixed.
PS:In my case all SAP printout were coming properly except the smartforms.
Regards,
Ashutosh
Edited by: ashutosh singh on Aug 18, 2008 10:20 AM -
Dear experts,
I want to display some graph in the sapscript or smartforms. But I am not getting any clue. Please can anybody suggest me what should I do??
Thanks a lot in advance..
Regards,
SriniwasHi
SAP SCRIPT
To create a logo in SAP printouts just do the following
1. Save a Logo using Imaging, Paint shop Pro or Corel Draw as Tiff file.
2. Run program RSTXLDMC and enter the following parameters
Enter file name C:\COMPLOGO.TIF
UOM CM
Line width for text 132
Text name ZHEX-MACRO-COMPLOGO
Text ID ST
Text language = E
Number of Tiff gray levels (2,4,9) 2
3. Then Create a new window 'COMP' with attributes;
Window COMP description Company Logo
Left margin 7.00 CH window width 10.00 CH
Upper margin LN window height 8.00 LN
Finally in the text element, mention
/: INCLUDE 'ZHEX-MACRO-COMPLOGO' OBJECT TEXT ID ST LANGUAGE 'E'.
Please note that if object name is not indicated as 'ZHEX... the logo may not be printed!
You will not be able to see the logo in a test print. The same will be printed in actual printout.
SMARTFORM
1) In Smart Forms Editor, In left pane, right Click any Page (say Page1) and select Create -> Window, Give it a name and Description (Say Window1)
2) Right Click on Window (Window 1) and select Create -> Graphics, Give it a name and description
3) In general Attributes, Select Name, get search help (F4) , you will find a list of pictures
4) Select any picture and set its Resolution in DPI
5) Press F9 to open Smart Forms Builder, Select window (Window1) and In Output options window set, size and position of the Logo
6) Set any other parameters if required, save and activate.
7) If there is only 1 Window in the forms, set it as Main Window in general attributes.
8) Use TCode SE78 to upload new pictures and logos.
See the Thread Dynamic Graph in smartforms
Reward points for useful Answers
Regards
Anji -
IN SE78 : WHILE UPLOADING THE TIF FILE I AM GETTING THE ERROR
Hi ,
While uploading the drawing in se78 . iam getting the errror
"erroneous tif formate"
. PLz help me to upload the tif file thro se78.
even i removed the compression check box ,.
Thanks,
RaniHi
You can upload logo using SE78 or using program RSTXLDMC
or by using OAER
Steps for uploading Logo :-:
1. Goto the transaction OAER
2. Enter the class name as 'PICTURES'
3. Enter the class type as 'OT'
4. Enter the object key as the name of the logo you
wish to give
5. Execute
6. Then in the new screen select Standard doc. types
in bottom window
Click on the Screen icon
Now, it will ask for the file path where you have
to upload the logo
7. Now you can use this logo
To create a logo in SAP printouts just do the following
1. Save a Logo using Imaging, Paint shop Pro or Corel Draw as Tiff file.
2. Run program RSTXLDMC and enter the following parameters
Enter file name C:\COMPLOGO.TIF
UOM CM
Line width for text 132
Text name ZHEX-MACRO-COMPLOGO
Text ID ST
Text language = E
Number of Tiff gray levels (2,4,9) 2
3. Then Create a new window 'COMP' with attributes;
Window COMP description Company Logo
Left margin 7.00 CH window width 10.00 CH
Upper margin LN window height 8.00 LN
Finally in the text element, mention
/: INCLUDE 'ZHEX-MACRO-COMPLOGO' OBJECT TEXT ID ST LANGUAGE 'E'.
Please note that if object name is not indicated as 'ZHEX... the logo may not be printed!
You will not be able to see the logo in a test print. The same will be printed in actual printout.
SMARTFORM
1) In Smart Forms Editor, In left pane, right Click any Page (say Page1) and select Create -> Window, Give it a name and Description (Say Window1)
2) Right Click on Window (Window 1) and select Create -> Graphics, Give it a name and description
3) In general Attributes, Select Name, get search help (F4) , you will find a list of pictures
4) Select any picture and set its Resolution in DPI
5) Press F9 to open Smart Forms Builder, Select window (Window1) and In Output options window set, size and position of the Logo
6) Set any other parameters if required, save and activate.
7) If there is only 1 Window in the forms, set it as Main Window in general attributes.
8) Use TCode SE78 to upload new pictures and logos.
look at Thread Dynamic Graph in smartforms
Refer the links also -
Re: Dinamic Graph in smartforms
How to get file perperties in Unix server
Regards
Selvapandian Arunachalam -
Hi
Please clarify me regarding smart forms background logo. I'm trying to migrate sap script into smart forms, for the background logo in smart form is it required to write ABAP code, please let me know?
2) Is it possible for background pictures in script? Is there any document regarding logo/pictures in sap script or smartforms? is there standard forms like purchase order etc., in smart forms? Please correct me If i'm wrong...
Regards
sree reddyHi
Background LOGOS are possible only in smartforms not in Scripts
see the logo printing for Scripts and Smartforms and the important smartforms and scripts with their programs
SAP SCRIPT
To create a logo in SAP printouts just do the following
1. Save a Logo using Imaging, Paint shop Pro or Corel Draw as Tiff file.
2. Run program RSTXLDMC and enter the following parameters
Enter file name C:\COMPLOGO.TIF
UOM CM
Line width for text 132
Text name ZHEX-MACRO-COMPLOGO
Text ID ST
Text language = E
Number of Tiff gray levels (2,4,9) 2
3. Then Create a new window 'COMP' with attributes;
Window COMP description Company Logo
Left margin 7.00 CH window width 10.00 CH
Upper margin LN window height 8.00 LN
Finally in the text element, mention
/: INCLUDE 'ZHEX-MACRO-COMPLOGO' OBJECT TEXT ID ST LANGUAGE 'E'.
Please note that if object name is not indicated as 'ZHEX... the logo may not be printed!
You will not be able to see the logo in a test print. The same will be printed in actual printout.
SMARTFORM
1) In Smart Forms Editor, In left pane, right Click any Page (say Page1) and select Create -> Window, Give it a name and Description (Say Window1)
2) Right Click on Window (Window 1) and select Create -> Graphics, Give it a name and description
3) In general Attributes, Select Name, get search help (F4) , you will find a list of pictures
4) Select any picture and set its Resolution in DPI
5) Press F9 to open Smart Forms Builder, Select window (Window1) and In Output options window set, size and position of the Logo
6) Set any other parameters if required, save and activate.
7) If there is only 1 Window in the forms, set it as Main Window in general attributes.
8) Use TCode SE78 to upload new pictures and logos.
look at Thread Dynamic Graph in smartforms
Refer the links also -
Re: Dinamic Graph in smartforms
How to get file perperties in Unix server
SD
SALES ORDER/ENQUIRY/QUOTATION
Output type : BA00
ScriptForm Name : RVORDER01
Driver Program Name : RVADOR01
smartform name
DELIVERY NOTE
Output type : LD00
ScriptForm Name : RVDELNOTE
Driver Program Name : RVADDN01
smartform name : LE_SHP_DELNOTE
Smartform Driver Pgm: RLE_DELNOTE
INVOICE
Output type : RD00
ScriptForm Name : RVINVOICE01
Driver Program Name : RVADIN01
smartform name : LB_BIL_INVOICE
Smartform Driver Pgm: RLB_INVOICE
MM
PUCHASE ORDER/RFQ/CONTRACT
Output type : NEU
ScriptForm Name : MEDRUCK
Driver Program Name : SAPMF06P
smartform name : /SMB40/MMPO_L
smartform driver program: /SMB40/FM06P
GOODS RECEIPT
Output type : WE01
ScriptForm Name : WESCHEINVERS1
smartform name : /SMB40/MMGR1_A
smartform driver program: /SMB40/M07DR
GOODS ISSUE
Output type : WA01
ScriptForm Name : WA_SCHEINVERS1
smartform name : /SMB40/MMGI1_A
smartform driver program: /SMB40/M07DR
FI Forms
Account Statement : F140_ACC_STAT_01
Cheque Printing : F110_PRENUM_CHEK
Balance Confirmation: F130_confirm_01
Dunning Form: F150_DUNN_01
check the link below it provides steps to convert sap scripts to smartforms
http://www.ficoexpertonline.com/downloads/Iyer_SmartForms.pdf
SMARTFORMS -Driver Program
PO: /SMB40/FM06P
SO: /SMB40/RVADOR01
GR: /SMB40/M07DR
Reward if useful
regards
Anji -
Problem encountered when using RKD_WORD_WRAP
Hi all,
I have encountered a problem when using RKD_WORD_WRAP. The problem is that the paragraph is not being formatted nicely when i try to printout in Smartforms.
Eg is that I want to format this paragraph;
"Text Conversion: Convert Text Formats
The function module CONVERT_TEXT provides the
following format conversion options:"
However, when I output it out, the text was being displayed like this;
"Text Conversion: Convert Text Formats
The function module CONVERT_TEXT provides
the
following format conversion options:"
The problem is that even though after the "the" word, although that line still has some spaces, thecorresponsing words just wont get concatenate to the 2nd line (as seen above).
Is there any way to fix this?? Or is there a standard value to be use for the outputlens parameter so that the above situation will not occurs??Check the below program and output :
report ztest_ytt.
data input type string.
data SWASTRTAB like SWASTRTAB occurs 0 with header line.
start-of-selection.
input = 'The function module SWA_STRING_SPLIT that you have said is not
working successfully. It is still giving me the same problem where it is
appending a new line where there is still enough space for the word on
the current line'.
CALL FUNCTION 'SWA_STRING_SPLIT'
EXPORTING
INPUT_STRING = input
MAX_COMPONENT_LENGTH = 100
TERMINATING_SEPARATORS =
OPENING_SEPARATORS =
TABLES
STRING_COMPONENTS = SWASTRTAB
EXCEPTIONS
MAX_COMPONENT_LENGTH_INVALID = 1
OTHERS = 2
IF SY-SUBRC <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
loop at SWASTRTAB.
write:/ SWASTRTAB-STR.
endloop.
This is output :
The function module SWA_STRING_SPLIT that you have said is not working successfully. It is still
giving me the same problem where it is appending a new line where there is still enough space for
the word on the current line
Suppose you want to print 100 charcters in each line .. upto 95 charcters you have words perfectly the next will start at 97th ,so here word is <b>' Function'</b>
so this word will not fit into that line since you have 4 charcters,Function word is containg 8 charcters,this word will come in next line.
Check the program and give what ever input and see the results.
Thanks
Seshu -
after uploading the logo in scripts, if i release the script then logo will logo along with scripts or we have to do any processes for logo
Title was edited by:
Alvaro Tejada GalindoHi
Logo's should be transported/created first in the Target client first
then only if you send the script that logo will be printed
see the steps to upload the logo
SAP SCRIPT
To create a logo in SAP printouts just do the following
1. Save a Logo using Imaging, Paint shop Pro or Corel Draw as Tiff file.
2. Run program RSTXLDMC and enter the following parameters
Enter file name C:\COMPLOGO.TIF
UOM CM
Line width for text 132
Text name ZHEX-MACRO-COMPLOGO
Text ID ST
Text language = E
Number of Tiff gray levels (2,4,9) 2
3. Then Create a new window 'COMP' with attributes;
Window COMP description Company Logo
Left margin 7.00 CH window width 10.00 CH
Upper margin LN window height 8.00 LN
Finally in the text element, mention
/: INCLUDE 'ZHEX-MACRO-COMPLOGO' OBJECT TEXT ID ST LANGUAGE 'E'.
Please note that if object name is not indicated as 'ZHEX... the logo may not be printed!
You will not be able to see the logo in a test print. The same will be printed in actual printout.
SMARTFORM
1) In Smart Forms Editor, In left pane, right Click any Page (say Page1) and select Create -> Window, Give it a name and Description (Say Window1)
2) Right Click on Window (Window 1) and select Create -> Graphics, Give it a name and description
3) In general Attributes, Select Name, get search help (F4) , you will find a list of pictures
4) Select any picture and set its Resolution in DPI
5) Press F9 to open Smart Forms Builder, Select window (Window1) and In Output options window set, size and position of the Logo
6) Set any other parameters if required, save and activate.
7) If there is only 1 Window in the forms, set it as Main Window in general attributes.
8) Use TCode SE78 to upload new pictures and logos.
look at Thread Dynamic Graph in smartforms
Refer the links also -
Re: Dinamic Graph in smartforms
How to get file perperties in Unix server
Regards
Anji -
How to upload the .tiff file
when i try to the upload the .tiff file using RSTXLDMC program am not suceeded..
help me...
is there any transaction for preview purpose.... of what ever .tiff files uplHi
You can upload logo using SE78 or using program RSTXLDMC
or by using OAER
Steps for uploading Logo :-:
1. Goto the transaction OAER
2. Enter the class name as 'PICTURES'
3. Enter the class type as 'OT'
4. Enter the object key as the name of the logo you
wish to give
5. Execute
6. Then in the new screen select Standard doc. types
in bottom window
Click on the Screen icon
Now, it will ask for the file path where you have
to upload the logo
7. Now you can use this logo
To create a logo in SAP printouts just do the following
1. Save a Logo using Imaging, Paint shop Pro or Corel Draw as Tiff file.
2. Run program RSTXLDMC and enter the following parameters
Enter file name C:\COMPLOGO.TIF
UOM CM
Line width for text 132
Text name ZHEX-MACRO-COMPLOGO
Text ID ST
Text language = E
Number of Tiff gray levels (2,4,9) 2
3. Then Create a new window 'COMP' with attributes;
Window COMP description Company Logo
Left margin 7.00 CH window width 10.00 CH
Upper margin LN window height 8.00 LN
Finally in the text element, mention
/: INCLUDE 'ZHEX-MACRO-COMPLOGO' OBJECT TEXT ID ST LANGUAGE 'E'.
Please note that if object name is not indicated as 'ZHEX... the logo may not be printed!
You will not be able to see the logo in a test print. The same will be printed in actual printout.
SMARTFORM
1) In Smart Forms Editor, In left pane, right Click any Page (say Page1) and select Create -> Window, Give it a name and Description (Say Window1)
2) Right Click on Window (Window 1) and select Create -> Graphics, Give it a name and description
3) In general Attributes, Select Name, get search help (F4) , you will find a list of pictures
4) Select any picture and set its Resolution in DPI
5) Press F9 to open Smart Forms Builder, Select window (Window1) and In Output options window set, size and position of the Logo
6) Set any other parameters if required, save and activate.
7) If there is only 1 Window in the forms, set it as Main Window in general attributes.
8) Use TCode SE78 to upload new pictures and logos.
look at Thread Dynamic Graph in smartforms
Refer the links also -
Re: Dinamic Graph in smartforms
How to get file perperties in Unix server
Regards
Pavan -
i want to post logo in sap scripts can any guide me
rajuHi Karthik,
To create a logo in SAP printouts just do the following
1. Save a Logo using Imaging, Paint shop Pro or Corel Draw as Tiff file.
2. Run program RSTXLDMC and enter the following parameters
Enter file name C:\COMPLOGO.TIF
UOM CM
Line width for text 132
Text name ZHEX-MACRO-COMPLOGO
Text ID ST
Text language = E
Number of Tiff gray levels (2,4,9) 2
3. Then Create a new window 'COMP' with attributes;
Window COMP description Company Logo
Left margin 7.00 CH window width 10.00 CH
Upper margin LN window height 8.00 LN
Finally in the text element, mention
/: INCLUDE 'ZHEX-MACRO-COMPLOGO' OBJECT TEXT ID ST LANGUAGE 'E'.
Please note that if object name is not indicated as 'ZHEX... the logo may not be printed!
You will not be able to see the logo in a test print. The same will be printed in actual printout.
SMARTFORM
1) In Smart Forms Editor, In left pane, right Click any Page (say Page1) and select Create -> Window, Give it a name and Description (Say Window1)
2) Right Click on Window (Window 1) and select Create -> Graphics, Give it a name and description
3) In general Attributes, Select Name, get search help (F4) , you will find a list of pictures
4) Select any picture and set its Resolution in DPI
5) Press F9 to open Smart Forms Builder, Select window (Window1) and In Output options window set, size and position of the Logo
6) Set any other parameters if required, save and activate.
7) If there is only 1 Window in the forms, set it as Main Window in general attributes.
8) Use TCode SE78 to upload new pictures and logos.
Regards,
Satish -
hi,
i have one logo and i want to insert that logo into the smart forms
so can u suggest me the steps to insert that logo in smart forms.
regards,
kamalHi
SAP SCRIPT
To create a logo in SAP printouts just do the following
1. Save a Logo using Imaging, Paint shop Pro or Corel Draw as Tiff file.
2. Run program RSTXLDMC and enter the following parameters
Enter file name C:\COMPLOGO.TIF
UOM CM
Line width for text 132
Text name ZHEX-MACRO-COMPLOGO
Text ID ST
Text language = E
Number of Tiff gray levels (2,4,9) 2
3. Then Create a new window 'COMP' with attributes;
Window COMP description Company Logo
Left margin 7.00 CH window width 10.00 CH
Upper margin LN window height 8.00 LN
Finally in the text element, mention
/: INCLUDE 'ZHEX-MACRO-COMPLOGO' OBJECT TEXT ID ST LANGUAGE 'E'.
Please note that if object name is not indicated as 'ZHEX... the logo may not be printed!
You will not be able to see the logo in a test print. The same will be printed in actual printout.
SMARTFORM
1) In Smart Forms Editor, In left pane, right Click any Page (say Page1) and select Create -> Window, Give it a name and Description (Say Window1)
2) Right Click on Window (Window 1) and select Create -> Graphics, Give it a name and description
3) In general Attributes, Select Name, get search help (F4) , you will find a list of pictures
4) Select any picture and set its Resolution in DPI
5) Press F9 to open Smart Forms Builder, Select window (Window1) and In Output options window set, size and position of the Logo
6) Set any other parameters if required, save and activate.
7) If there is only 1 Window in the forms, set it as Main Window in general attributes.
8) Use TCode SE78 to upload new pictures and logos.
look at Thread Dynamic Graph in smartforms
Refer the links also -
Re: Dinamic Graph in smartforms
How to get file perperties in Unix server
Regards
Anji -
How to create and upload logo into script
hi guys,
can you help me how to create logo and upload the logo into sap script please...Hi
Welcome to SDN forum
SAP SCRIPT
To create a logo in SAP printouts just do the following
1. Save a Logo using Imaging, Paint shop Pro or Corel Draw as Tiff file.
2. Run program RSTXLDMC and enter the following parameters
Enter file name C:\COMPLOGO.TIF
UOM CM
Line width for text 132
Text name ZHEX-MACRO-COMPLOGO
Text ID ST
Text language = E
Number of Tiff gray levels (2,4,9) 2
3. Then Create a new window 'COMP' with attributes;
Window COMP description Company Logo
Left margin 7.00 CH window width 10.00 CH
Upper margin LN window height 8.00 LN
Finally in the text element, mention
/: INCLUDE 'ZHEX-MACRO-COMPLOGO' OBJECT TEXT ID ST LANGUAGE 'E'.
Please note that if object name is not indicated as 'ZHEX... the logo may not be printed!
You will not be able to see the logo in a test print. The same will be printed in actual printout.
SMARTFORM
1) In Smart Forms Editor, In left pane, right Click any Page (say Page1) and select Create -> Window, Give it a name and Description (Say Window1)
2) Right Click on Window (Window 1) and select Create -> Graphics, Give it a name and description
3) In general Attributes, Select Name, get search help (F4) , you will find a list of pictures
4) Select any picture and set its Resolution in DPI
5) Press F9 to open Smart Forms Builder, Select window (Window1) and In Output options window set, size and position of the Logo
6) Set any other parameters if required, save and activate.
7) If there is only 1 Window in the forms, set it as Main Window in general attributes.
8) Use TCode SE78 to upload new pictures and logos.
look at Thread Dynamic Graph in smartforms
Refer the links also -
Re: Dinamic Graph in smartforms
How to get file perperties in Unix server
regards
Anji -
Hi experts
I am very new for SAP NOTE modification and i am alone here.
Please any one guide me.
I want to develop the FORM16A as per this year.
for that i got the sap note 1486147.
i download that and got very clear steps
In that there designed printout from Smartform with name of J_1IEWT_CERT
and they gave driver program as J_1IEWT_CERT.
But driver program have the OPEN_FORM,WRITE_FORM and START_FORM,so i think it is Script.
Please guide me,the driver program is script and form is smartform how we will link.
what are the modifications i have to do.
Please help me i am alone here.
Thanks advance.Hi Krishna,
A Breif of the SAP Note 1486147
Other terms
Form 16A, Certificate , Legal change, April 2010 , J_1IEWT_CERT,
J1INCERT , J1INCCERT , reprint
Reason and Prerequisites
Notification from the IT Department.
Legal change
Solution
New Smartform has been created to suuport the new Certificate format.
Solution includes chnages in the certificate program, Smartform creation and a new customization.
Attached New_Form16A.zip contains 3 objects:-
Form16A_Smartform.PDF, Form16A_DDIC.pdf, J_1IEWT_CERT_style.xml
and J_1IEWT_CERT.xml
First download J_1IEWT_CERT.xml and to J_1IEWT_CERT_style.xml to your
local machine.
1. Please follow the manual steps given in the attached pdf - Form16A_DDIC.pdf to create new DDIC objects before applying the code corrections.
2. Create new Smartform 'J_1IEWT_CERT' as explained the attached PDF - 'Form16A_Smartform.PDF'
3. Apply the correction instructions.
In the certificate, Income tax department address has to be displyed.
To support this, new customization is created. Please maintain IT department address in the view (SM31 - J_1I_SECCO_CIT) for every Section Code under the company code.
Create an entry in table TSADRV for J_1I_SECCO_CIT to get address block.
following values should be filled in.
Table - J_1I_CIT
Field - ADRNR
DD Table - J_1I_SECCO_CIT
DD Field - ADRNR
Addrss Group - CA01
Save it.
Maintain TAN against Section codes in the view J_1I_SECCO_CIT.
Note:-
'Run in preview mode' checkbox has been provided in selection screen, If it is selected while running the certificate, it will not generate a certificate number even PRINT button is clicked.
The note is very clear what to do, Download the file.zip available at the bottom & read the PDF file. its very clear, also they have mentioned how to make entires in tables & other stuff as well.
Cheers,
Dileep .C -
Hi I want to display a logo into my Smart form.That logo need to be first uploaded in SAP Server. How to do that??
Hi
To Upload a graphic then 1st upload it to the sap using Tx code SE78
To create a logo in SAP printouts just do the following
1. Save a Logo using Imaging, Paint shop Pro or Corel Draw as Tiff file.
2. Run program RSTXLDMC and enter the following parameters
Enter file name C:\COMPLOGO.TIF
UOM CM
Line width for text 132
Text name ZHEX-MACRO-COMPLOGO
Text ID ST
Text language = E
Number of Tiff gray levels (2,4,9) 2
3. Then Create a new window 'COMP' with attributes;
Window COMP description Company Logo
Left margin 7.00 CH window width 10.00 CH
Upper margin LN window height 8.00 LN
Finally in the text element, mention
/: INCLUDE 'ZHEX-MACRO-COMPLOGO' OBJECT TEXT ID ST LANGUAGE 'E'.
Please note that if object name is not indicated as 'ZHEX... the logo may not be printed!
You will not be able to see the logo in a test print. The same will be printed in actual printout.
SMARTFORM
1) In Smart Forms Editor, In left pane, right Click any Page (say Page1) and select Create -> Window, Give it a name and Description (Say Window1)
2) Right Click on Window (Window 1) and select Create -> Graphics, Give it a name and description
3) In general Attributes, Select Name, get search help (F4) , you will find a list of pictures
4) Select any picture and set its Resolution in DPI
5) Press F9 to open Smart Forms Builder, Select window (Window1) and In Output options window set, size and position of the Logo
6) Set any other parameters if required, save and activate.
7) If there is only 1 Window in the forms, set it as Main Window in general attributes.
8) Use TCode SE78 to upload new pictures and logos.
look at Thread Dynamic Graph in smartforms
Refer the links also -
Re: Dinamic Graph in smartforms
How to get file perperties in Unix server
Regards
Pavan -
Smartform output ( printout ) is not the same as the preview
Dear Freinds,
I have developed smartform , iam able to get data
very much clear font and the design . However when i running the smart form through repot to give print using the Output Device Locl or LP01. I can see the output is not coming in the printout which is there in Print Preview.
The Print Preview as below :
Print preview the below is the data:
ID : _____________QTY :____________
Address :_________Pincode :____________
Final printout in the paper (when using the output device
Locl or LP01) the data is coming as below
Name : _______ QTY :____________
Address : ___________ Pincode :____________
we can the see the above printing is not correct , as the lines are coming short when
compared to print preview and it is looking as broken lines....
I have used underline for printing the lines using the Paragraph Format from Smart Styles.
Please could you tell me what changes i have to do so that the line should stretch and touch the Qty
, in the printpreview data is coming correctly i can see the line touches till the Qty.
. Please suggest me what i have missed in the smartforms..
thanks & regards
madhuri
Edited by: madhuri_2000 kumari on Oct 29, 2008 8:50 AMDear Neeraj,
The actual problem is the when i have in the ouput as below :
Name : &wafinal-Name&__________ Designation : &wafinal-Job&________
so iam getting data for Name : Madhuri______ Designation: Supervisor -
> this data
is coming for me correctly when i see in the Print preview.
As in the page the two fields Name and Designation are in the same line i want the underline which is the under Madhuri should extend till the text Designation , but i found in the print preview it is coming
correctly , however in the printout it is coming ast Name : Madhuri______ Desgination: Supervisor______.
i can see there is a gap coming between end of the underline of the Name and the Designation.
Actually my requirement is i wan to have
Name : _____________________________Designation:_________________________________
in first row. But in the printoverview iam ble to see exactly the same above however when i take printout i can the output as
Name : ______________________ Designation:____________________________
I have done in the smartform as per below :
I have used the Table > in the table i have used the Main Area> in the Main area i have created in Row1 and created a cell> Splited the Cell in two > so Row1 is having two cells> in the first cell i have created one text and given in the text area as Name : &Wa_final-Name&____ and in the second cell i have created another text and given in the text area as Designation : &wa_final-Job&________.
So i am not able to extend the underline of the Name : &Wa_final-Name&____ till Designation: &wa_final-Job&________, however iam able to see in the printout and only not getting truncated inthe
printout.
please could let me know how and where i went wrong in getting extended till Designation.
Regards
Madhuri.
Maybe you are looking for
-
PE51 - How to display a custom result in a PE51 forms?
Hi experts, I want to display the result of a specific Module Function in a PE51 form (payslip). The module function returns a table with a proper contain for each employee / period. I don't know the size of the table (number of lines) for each emplo
-
Spry Menu problem with using a transparent background image
Hi- I'm new to CS5 and Dreamweaver. I just finished the beginning webpage tutorial and I have started to work on a personal project. The Problem: when I use a transparent png image as a backgroun-image for my spry menu it shows up fine in live view,
-
Using European Outlets with Macbook Pro
Hello Im about to buy a Macbook Pro and am traveling to New Zealand for a semester abroad. I believe this country uses the same outlet system (and higher voltage) as most European countries. My question is: Is there an adapter sold by apple for conve
-
Hello , We nned to remove the autorisations for our user to go on 'bex web analyser " when the log on the BYportal . We want that only "key users ' could access to the Bex web analyser " . Others users have to acces only to the bookmarks we have buil
-
FCP not recognizing Panasonic videocamera
I am using a Panasonic DVC30 video camera and trying toconnect to Final Cut Pro version 5.1.4 on my Mac that's running OS 10.5.8. Thecamera is connected to the computer using a 4pin firewire on one side and 6 pinon the other side. I have been unable