Problem Adding DSP's to 2811 router

I'm at a customers site and I've just added a PVDM2-16 to the existing PVDM2-32. I then changed the pri-groups from an initial 16 channels of E1 to 31.
Now when I dial in from externally, I'm not getting a ringtone just about 10 seconds of buzzing before the call plays fast busy. You can see the call is connected on the gateway but that's about it.
I'm running CCM 4.2(3).
Any ideas? It's a bog standard config that I regularly use.
Cheers - Dave

Hi Fred,
I'm using H323. Here's most of the config.
clock timezone GMT 0
clock summer-time BST recurring
network-clock-participate wic 0
network-clock-select 1 E1 0/0/0
ip cef
voice-card 0
no dspfarm
voice service voip
h323
h245 caps mode restricted
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g729r8
voice class h323 1
h225 timeout tcp establish 3
controller E1 0/0/0
pri-group timeslots 1-16
description ## xxxx ##
interface Loopback0
ip address 192.168.10.1 255.255.255.255
interface FastEthernet0/0
description ## Connection to Core Switch 7/48 ##
ip address 10.x.x.x x.x.x.x
duplex full
speed 100
h323-gateway voip bind srcaddr 10.17.10.1
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface Serial0/0/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
ip route 0.0.0.0 0.0.0.0 x.x.x.x
ip http server
ip http authentication local
no ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
control-plane
voice-port 0/0/0:15
cptone GB
Cheers
Dave

Similar Messages

Problem adding computers for WRT150N wireless router

I just set up my home wireless network and can connect from my laptop (which is running Vista). Following the instructions exactly, I am unable to connect my Desktop (running XP). I got to the part where I must enter www.linksysfix.com/ela in the web browser but nothing loads. The cable that is currently connecting my desktop to the router is the same one that I used to connect my laptop so I know it's not defective. What gives?

Check if you have a static ip on the pc. Go to control panel>network connections>right-click on local area connection and click on properties>highlight internet protocol tcp/ip and click properties. Make sure it's set to obtain ip address automatically and obtain dns.
Good luck! (",)
The box said windows xp or better... So I installed Linux!

High CPU usage on 2811 router

dear support
i have a problem recently, i have a 2811 router, there are several EIGRP VPN tunnel setup on it, recently i found this router running high CPU utilization, it almost reach 80 percent at the most day busy time, when i try to find what process causing that after " show proc cpu", the summarize number not such high, it estimate not more than 20 percent. i know in old Cisco IOS there is a command "show platform health", but seem this not exist in 2800 serials any more.
so my question is what can i do next step to finding out what is causing high CPU usage, so that i can decide if the router need to be upgraded.
thanks very much

dear support
i have a problem recently, i have a 2811 router, there are several EIGRP VPN tunnel setup on it, recently i found this router running high CPU utilization, it almost reach 80 percent at the most day busy time, when i try to find what process causing that after " show proc cpu", the summarize number not such high, it estimate not more than 20 percent. i know in old Cisco IOS there is a command "show platform health", but seem this not exist in 2800 serials any more.
so my question is what can i do next step to finding out what is causing high CPU usage, so that i can decide if the router need to be upgraded.
thanks very much

2811 router boot problem

HI
I have 2811 router when i boot the under following error message comes. comes in roomon mode . I upgrade IOS but same problem arise.
Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(3c), RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Sat 07-Jan-06 04:34 by alnguyen
Image text-base: 0x400A1678, data-base: 0x42D00000
****** ERROR detected on PCI0 Bus
****** Try RESEATING all modules in the system
****** pci0_int_cause 0x00000040,
****** pci0_err_addr 0x30B08038, pci0_err_cmd 0x00000006
****** PCI Master Read Parity Error
%ERR-1-FATAL: Fatal error interrupt, reloading
err_stat=0x0
=== Flushing messages (09:11:27 UTC Wed Jul 19 2006) ===
Queued messages:
09:11:27 UTC Wed Jul 19 2006: Interrupt exception, CPU signal 22, PC = 0x0
-Traceback= 0x4025E7B8 0x4008B1C4 0x4025FAA4
$0 : 00000000, AT : BFA00000, v0 : 00000000, v1 : 45620000
a0 : 00000006, a1 : 00000000, a2 : 00000005, a3 : 000F4240
t0 : 000186A0, t1 : 00000000, t2 : 34008000, t3 : FFFF00FF
t4 : 4008E950, t5 : 00000000, t6 : 00008140, t7 : 45DAA238
s0 : 45618048, s1 : 45660000, s2 : 44F10000, s3 : 452E0000
s4 : 453D0000, s5 : 00000016, s6 : 00000000, s7 : 45DAA818
t8 : 00000000, t9 : 00000006, k0 : 00000018, k1 : 00000000
gp : 453E07EC, sp : 45DAA770, s8 : 45A8D120, ra : 4025E7A8
EPC : 4025E7B8, ErrorEPC : 400011AD, SREG : 34008003
MDLO : 000003E8, MDHI : 00000000, BadVaddr : 00000118
Cause 0000000C (Code 0x3): TLB (store) exception
-Traceback= 0x4025E7B8 0x4008B1C4 0x4025FAA4
No warm reboot Storage
*** System received a Bus Error exception ***
signal= 0xa, code= 0xc, context= 0x4561a104
PC = 0x4009483c, Cause = 0x20, Status Reg = 0x34008002
System Bootstrap, Version 12.4(1r) [hqluong 1r], RELEASE SOFTWARE (fc1)
Copyright (c) 2005 by cisco Systems, Inc.
thanks
biplob
it is hardware problem ????.
can any one help to solve this problem.
thanks
Biplob

Hi,
For the problem mentioned see the cause below,
ERROR: The system encounters a 'Bus Error' when the processor tries to access
a memory location that either does not exist (indicating a software issue) or does
not respond properly (indicating a hardware issue).
TRY THIS:
1. For 68000 Processor based platforms, carry out the following steps:
Consider the output:
"System restarted by bus error at PC 0x30EE546, address 0xBB4C4".
Here the system is trying to access the address "0xBB4C4"
a. Based on the address accessed by the router when the 'Bus Error' occurred,
use the "show region" command to determine the memory location to which
the address corresponds. If the address reported by the 'Bus Error' does
not fall within the ranges displayed in the show region output, it implies
that the router was trying to access an invalid address. This in turn indicates
a Cisco IOS Software problem. Use the Output Interpreter to decode the output
of the "show stacks" command to identify the software bug that is causing
the bus error.
b. If the address falls within one of the ranges in the "show region" output,
it implies that the router was accessing a valid memory location, but the
hardware corresponding to that address did not respond properly. This indicates
a hardware problem. Find the memory address that the system is trying to
access (for example in the above output, it is 0xBB4C4), and also the range
of memory addresses between which this address falls. The hardware issue
is most likely related to the corresponding component. If a new router has
been installed, or if the router has been moved from one location to another,
the memory chips may have become loose. It is recommended that you re-seat
or firmly push the memory chips into the slot.
For more information, see Troubleshooting Bus Error Crashes.
2. For the RISC Processor based platforms, use the Output Interpreter Tool to decode
the output of the "show stacks" command and identify the Cisco IOS Software
bug that is causing the bus error.
and even it is very much look like a bug in the software.
Rate if it does,
Rgs,

ISCSI boot with Intel NICs added to windows 2008 r2 routing table causes non iscsi traffic to attempt default routes on iscsi networks

I have a server with Intel 82576 Gigabit Dual Port Nics. I have configured them to use iSCSI boot the primary looks to 10.0.0.1/24 and the secondary looks to 10.0.1.1/24. The target is configured correctly. Everything boots as expected.
I have added the MPIO feature and configured MPIO for the iscsi initiator as per: http://blogs.technet.com/b/migreene/archive/2009/08/29/3277914.aspx.
My issue is that the iSCSI networks show up in the routing table like so:
I did not configure a default route in the Intel setup utility:
I tried to explicitly remove the 0.0.0.0 entry and leave blank, with no change. As you can see with the above routing table traffic attempts to travel over these routes:
C:\Users\Administrator>ping google.com
Pinging google.com [209.85.145.99] with 32 bytes of data:
Reply from 10.0.0.201: Destination host unreachable.
Reply from 10.0.1.201: Destination host unreachable.
Reply from 209.85.145.99: bytes=32 time=23ms TTL=51
Reply from 209.85.145.99: bytes=32 time=22ms TTL=51
Ping statistics for 209.85.145.99:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
A ping to the outside world first attempts on 10.0.0.x/24 network, then on 10.0.1.x/24 network and then finally on the network the traffic should go over. I don't want my iSCSI traffic to ever show up with a default route. How do I get rid of it?
route delete 0.0.0.0 mask 0.0.0.0 "on-link" results in: The route deletion failed: The parameter is incorrect.
route delete 0.0.0.0 mask 0.0.0.0 on-link results in: The route deletion failed: The parameter is incorrect.
route delete 0.0.0.0 deletes all default routes, then I have to add back in the "valid default route" of 192.168.100.6.
I would like to not have to do a route delete though.

So I've sort of given up on fixing the gateway assignment in the route for iSCSI boot. I configured a DHCP server to give out the information required by iSCSI boot and configured the network cards to use DHCP for their configuration. I insured
that my DHCP server gave out no default gateway entry. However, I still got the undesired routes in the routing table. This makes me assume that there isn't a "fix" for it, only the workaround.
Here is the script I run on each iSCSI Boot initiator (you would obviously change the ip number to suit your environment):
@Echo off
Rem fixes iscsi route problem as shown below:
Rem IPv4 Route Table
REM ===========================================================================
REM Active Routes:
REM Network Destination Netmask Gateway Interface Metric
REM 0.0.0.0 0.0.0.0 On-link 10.0.0.200 10255
REM 0.0.0.0 0.0.0.0 On-link 10.0.1.200 266
REM 0.0.0.0 0.0.0.0 192.168.100.6 192.168.100.98 266
REM The top 2 lines are on the iscsi interface and traffic tries to go out it
REM We need to delete the routes, so we'll just delete all gateway routes and
REM add back in the one we care about.
route delete 0.0.0.0 >c:\iscsibootroutefix.log
route -p add 0.0.0.0 mask 0.0.0.0 192.168.100.6 >>c:\iscsibootroutefix.log
After running it I get:
IPv4 Route Table
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.100.6 192.168.100.98 11
10.0.0.0 255.255.255.0 On-link 10.0.0.200 10255
10.0.0.1 255.255.255.255 On-link 10.0.0.200 10255
10.0.0.200 255.255.255.255 On-link 10.0.0.200 10255
Then I added a task in “task scheduler” of "administrative tools" that ran as the user “system” “when the computer starts” that runs this script.

Cannot place order ERROR: "There was a problem adding your product to cart"

Hey guys,
Well, once again Best Buy's online system is preventing me from making an order. It seems like nearly every time I log in I experience some new problem. This time, I'm unable to add anything to my cart. It doesn't matter what item I try to add to my cart or what browser I use or if I clear cookies...it happens every time, on every browser, with every product in the store. The error shows a red & white triangle with a message "There was a problem adding your product to cart".
Just to clarify ahead of time: 1) I have already tried signing in using 4 different browsers (explorer, firefox, chrome, opera) & they all give the same error; 2) Prior to posting here I researched this problem & found out it is somewhat common & has been occurring since at least 2012 on BestBuy.com; 3) Every time someone posts in here about this problem, customer service offers the same "fix" every time - to sign out, clear their browser cache of cookies, shut down the browser, restart the browser, sign back in, etc.... The only problem is, this "solution" has not worked ONE time our of the many times this problem has cropped up in here over the past 3+ years. Why this "solution" keeps getting told to people even though it never works is beyond me. But, there you have it.
Just to clarify: I have already tried this solution, And just like with everyone else before me, it didn't work for me either. So, what's the next step? There must be something else that can be done other than waiting a couple more days for it to magically fix itself (it seems that is the only thing that ever "works"...is to let several days go by and the problem ends up getting fixed in some back-end server-side patch up).
What I'm hoping for from you is a solution that can fix this immediately. This problem has already prevented me from making a couple purchases for items that were temporarily on sale over the past couple days. So, those are lost sales for Best Buy. What I'm hoping to do now is pre-order the Elder Scrolls Online (PS4) in order to take advantage of the $10 pre-order reward. The game releases on Tuesday the 9th. So, in order to get this done in time I need to place the order sometime today (on the 8th).
With all these repeated technical problems making purchasing a chore & wasting my time every single time I want to buy a product it's almost as if Best Buy is telling customers "We don't care if our online system works reliably...go spend your money at Amazon instead". lol
Thank you in advance for your timely help on this matter.
-Marc (removed per forum guidelines)

Hello mjswooosh,
I'm very disheartened to hear that you've had ongoing problems when attempting to order from BestBuy.com. Our goal is ever to provide a fun and efficient shopping environment! Certainly creating aggravation serves neither you nor us and I apologize sincerely for this having been your experience.
We recommend the troubleshooting steps you mentioned (i.e., clearing the browser cache, deleting temporary internet files and cookies) because this is the most common cause of this type of problem. I too have encountered this issue from time to time and these steps have almost always resolved the problem. I say almost always because there's one further step you can try: ensure that you have signed out of BestBuy.com, then perform the browser maintenance steps we've recommended. Afterward, before signing in to BestBuy.com, add your desired items to your cart and sign in as part of the checkout process. When the standard steps have not netted a resolution for me, this has solved the problem each time.
I hope this helps. I'm very grateful that you took the time to write to us with your concerns and for sharing your very valuable feedback about your online experience.
Sincerely,
John|Social Media Specialist | Best Buy® Corporate
Private Message

Problem adding HP J6400 all-in-one printer

We have an HP Officejet J6400 all-in-one printer here at work, and all of our computers have had no problem adding this printer except one: an older iMac, PowerMac 6.1 (with the white domed base). The driver is installed, and the computer sees the driver, but when I click to add it eventually it gives me this error:
"An error occurred while trying to add the selected printer. client-error-not-authorized"
I was on the phone with HP for an hour and they couldn't figure it out on their end. Has anyone had a similar problem, or have a solution?

Hi,
I request you to try the following:
For network connection:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03086294&tmp_task=useCategory&cc=us&dlc=en&lc=e...
For USB:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03521864&tmp_task=useCategory&cc=us&dlc=en&lc=e...
Although I am an HP employee, I am speaking for myself and not for HP.
Say thanks by clicking the "
Kudos! Thumps Up" which is on the right
Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue
Regards,
Ray

Problems with a WRT54G wireless linksys router.

Hello, I'm having problems with my WRT54G linksys wireless router.
With this router, I tend to get lag spikes and often disconnect while playing online games at a certain time. The spikes usually get worse
during the afternoon/evenings (2pm-12am PST).
Some information about my setup:
Firmware version: v.8.00.7
Shaw high speed cable (i think ~10mbit connect)
xp/vista OS (two computers linked up via router)
- Both computers are connected via wire, not wireless
I've changed settings for my router through advice, but nothing seems to work. Nobody else is connected to my router because I get nothing
in the logs and the DHCP client list has only 2 IPs. I'm sure my router is the one giving me lag spikes because I sometimes connect my
modem directly to my computer (the XP) and receive no lag spikes. Someone does use wireless, but I turn wireless off at times so that
isn't the problem. I've also secured my wireless, so I know it isn't the problem.
Anyone know what's causing these lag spikes and how I can fix it? Do I need a new router?
If anymore information is needed, please do not hesitate to ask.
Message Edited by Dysouk on 10-17-2009 12:24 AM
Not so computer savvy

Try to readjust the wireless settings of the router...Open the linksys setup page and try the following settings...
- Reduce the MTU size to 1364.
- Change the Wireless Channel to 11-2.467GHz.
- Under Advanced Wireless Settings,Change the Beacon Interval to 75,Fragmentation Threshold to 2304,RTS Threshold to 2304
Now,check the difference...If you are still facing the same problem then,try to upgrade/reflash the router's firmware,reset the router and reconfigure it from the scratch.

I upgraded to Mountain from Snow and find that there is now a problem adding iphoto to the cloud. I have iphoto '08,version 7.1.5. Tried to follow one poster's advice and upgrade to 9.1 but I need 9.0 first and I can't find that. suggestions? thanks!

I upgraded to Mountain from Snow and find that there is now a problem adding iphoto to the cloud. I have iphoto '08,version 7.1.5. Tried to follow one poster's advice and upgrade to 9.1 but I need 9.0 first and I can't find that. suggestions? thanks!

You have to buy iPhoto from the Mac App Store.

Issue / problem adding audio in Presenter 7 (PowerPoint 2010)

Since I got a new PC (Windows 7), I'm having an issue / problem adding audio in Presenter 7 (PowerPoint 2010).
It doesn’t happen every time, but randomly with many presentations...
In PowerPoint, right after I import audio (through Presenter) and click “ok”, I get the following errors:
Then, I can't get into the "import/sync/edit" mode, from the Presenter tab...
Already tried reinstalling Presenter, resaving new presentations, deleting the .ppcx/audio folders, importing the audio locally (vs from my network drive), etc.
Then sometimes, randomly, it will let me get back in and edit the audio, after numerous attempts…?!? I can't figure out what the pattern is, which is causing this new problem (never had this problem before, w/ my old PC - Win XP / PowerPoint 2003 / Presenter 6 & 7)
Anybody have an idea what the issue could be?
Thanks,
Mike P.

Hello,
I tried to reproduce this issue but I am not getting any error message. Please provide us following information; this might help to reproduce this issue:-
1) You are seeing this issue in PPT or PPTX
2) You seeing this issue in newly created presentations or its just old presentation which is not working properly.
3) OS and PowerPoint version
4) If this issue is consistent on any particular presentation then please share it.
5) Can we have exact reproducible steps
Regards,
Shubhi

All new podcasts blank - There was a problem adding "" to iTunes.

All new podcast episodes have a blank name, but the description is there. Clicking the exclamation point next to it yields - There was a problem adding "" to itunes.
This is not just my old subscriptions but new ones as well. The episode actually downloads completely but does not get added to my library.
Anybody have a suggestion how to resolve this?

After days of no solution, as soon as I post it decides to resolve this by itself.

Problem adding elements to a group after removing everything...

Hi everyone,
I would really appreciate some help on something. I have a Group that has some Buttons in it. This Group is in one of fours States, and there is a componant for each State. After the user goes through the rest of the program and comes back to this State, I want to remove the old buttons, and add new buttons with new values. Bascially, I want to refresh the componant when it is visited a second time. I have a problem adding new Buttons to the group when the user revisits the componant / state.
The group is created:
          <s:VGroup id="buttons" x="0" y="35" height="400" width="280" />
When the init function for that componant is called, buttons are added from an array of buttons:
for(var i:int = 0; i < 10; i++){
          var button:Button = questions[i];
          trace(button);
          button.addEventListener(MouseEvent.CLICK, myEventHandler);
          trace(buttons);
          buttons.addElement(button);
When the user moves on to the next State, the buttons are removed:
if(counter == 4){
          buttons.removeAllElements();
          FlexGlobals.topLevelApplication.currentState = 'Summary';
When the user comes back to the initial state, the buttons are not added to the Group like they are the first time. The output of the trace as each button is added is also different the second time:
First time: (successful)
Main.MainBackground2.contentGroup.gameComp.buttons
button8
Second time:
buttons
button8
Can anyone point me in the right direction? And better question, is there a better way I should be doing this?
Is there a better way to refresh everything within a component upon viewing it s second time?
Thanks in advance!

I'm not sure why you are using addElement() to add the buttons. Aren't you supposed to let the state functionality handle when the buttons should be visible? That's the cleanest way to do it in most cases. You may want to post a larger code sample, where you have boiled down the code into a minimal sample that still enhibits the issue.
If this post answers your question or helps, please mark it as such.
Greg Lafrance - Flex 2 and 3 ACE certified
www.ChikaraDev.com
Flex Training and Support Services

Cisco 2811 Router with 3 ADSL card and load balancing

Dear All,
I have few queries:
1. Does Cisco 2811 Router support 3 ADSL card?
2. We are the ISP. I want to do load balancing with 3 dsl
line on Cisco 2811 Router.
Please send me the linke for this configuration.
Thanks/Regards
Atul

hi
In 2811 you have 4 HWIC and 1 NME you can install 1-port ADSL WAN Interface Cardon the HWIC slots.
Also just enable 3 default (equal cost) routes towards the interfaces which will take care of the load balancing.
if you need more info and inputs do post out with ur requirements along with network topology in place at present..
regds

Need to default 2811 router

Hi all,
Please bear with me. I noticed several topics along the lines of password recovery for a 2811 router and do not mean to ask a redundant question. I've followed the .pdf instructions and the router will reboot as normal every time. I manage to get to the rommon 1> and when I initially entered the confreg command as outlined in the password recovery steps it would not recognize the confreg command. I ended up typing a ? and all the avaialble commands listed... after the commands listed, the CLI would allow me to type confreg 0x2142 which resulted in a message "need to reload or power cycle" (or something to that effect). After typing the reset, the 2811 reloads, but reboots to normal condition. I tried the confreg 0x102 method and got the same result. After several attempts, it seems like the procedure is not working. So how can I simply default the router and start from scratch if the recovery procedure fails?
Thank you!

Hello
Can you try the below:-
thanks
please rate all useful information
Shut down the router.
Remove the compact flash that is at the back of the router.
Power on the router.
Once the Rommon1> prompt appears, enter this command:
confreg 0x2142
Insert the compact flash.
Type reset. /you forget to type reset/
When you are prompted to enter the initial configuration, type No, and press Enter.
At the Router> prompt, type enable.
At the Router# prompt, enter the configure memory command, and press Enter in order to copy the startup configuration to the running configuration.
Use the config t command in order to enter global configuration mode.
Use this command in order to create a new user name and password:
router(config)#username cisco privilege 15 password cisco
Use this command in order to change the boot statement:
config-register 0x2102
Use this command in order to save the configuration:
write memory
Reload the router, and then use the new user name and password to log in to the router.

Problem adding Video to Captivate Slide

Hi,
I'm having a problem adding an FLV video file to Captivate. Basically, after I've published to a SWF file, the video doesn't appear on the slide at all. It's just blank.
After researching a bit, I found that the FLV file MUST include *metadata*.
However, I added medatada with VLC Media Player, and it still shows the same behavior. Must it include a certain *amount* of metadata? Is there a *type* of metadata without which the video will not show?
Adobe's Help thread talks about something called the "Flash Video Kit" - is that a stand alone product or an extension of another product? Is it free? Are there any other free alternatives?
I'm just very confused.
Thank you!

I ended up answering my own question. But just in case this helps anyone else, I'm going to post my solution.
Essentially, I just re-created the video in MP4 format. Then I used MetaZ (for Mac) to write Meta Data to the video. Lastly, I imported the video as an object and when I published the video, Captivate transmuted it to the necessary FLV format.
Now the video displays properly.

Problem Adding DSP's to 2811 router

Similar Messages

Maybe you are looking for