Problem after upgrade a PRIME-NCS-APL-K9 from version 1.1.0.58 to Prime Infrastructure 1.2

I have upgraded a PRIME-NCS-APL-K9 from version 1.1.0.58 to Prime Infrastructure 1.2
First I have installed the Path "ncs_patch-1.1.0.58-upgrade-pi_1.2.tar.gz" and then the
"PI-upgrade-bundle-1.2.0.103.tar.gz".
after the upgade I have got the Message "Upgrade Successful".
Now when I start the NCS i get the following error message
egghead/admin# ncs start
Starting Network Control System...
Unable to verify hardware.
This may take a few minutes...
Health Monitor is already running.
Failure during Network Control System startup. Check launchout.log for details.
In the launchout.log are this messages:
Starting Health Monitor as a primary
Checking for Port 8082 availability... OK
truststore used is /opt/CSCOlumos/conf/truststore
truststore used is /opt/CSCOlumos/conf/truststore
Starting Health Montior Web Server...
Health Monitor Web Server Started.
Starting Health Monitor Server...
Health Monitor Server Started.
Starting Remoting Service: Reporting Server
Checking for running servers.
00:00 Check complete. No servers running.
Starting Server ...
Starting Remoting Service: Reporting Server
The Report Server startup script is already running waiting for report server to start
Starting Remoting Service: Reporting Server
The Report Server startup script is already running waiting for report server to start
Starting Remoting Service: Reporting Server
The Report Server startup script is already running waiting for report server to start
Starting Remoting Service: Reporting Server
The Report Server startup script is already running waiting for report server to start
have anyone an idea whats wrong?
thank you for your help
Kurt

i have the same problem
NCS/admin# ncs status
Health Monitor Server is starting.
Reporting Server is Starting
Ftp Server is running
Database server is running
Tftp Server is running
Matlab Server is running
NMS Server is stopped.
SAM Daemon is running ...
DA Daemon is running ...
Syslog Daemon is running ...
status
I try it
To get it back up and running do the following from the CLI.
1. Stop the NCS
2. Run 'ncs db reinitdb'
3. Start the NCS
but the status is the same

Similar Messages

Problems after upgrading to Quicktime 7.1.3 from 7

After upgrading to QT 7.1.3 images that were fine before in videoclips, still shots and content in webpages now have a faint Q with a ? in the middle. On my daughters myspace page some of the clips and images she had uploaded, now show this too.
I tried to restart, I also just tried upgrading to QT Pro to see if that help. NOPE.....
PLEASE HELP
G4 Mac OS X (10.3.9)
G4 Mac OS X (10.3.9) Lacie DVD drive , HP 7310 all in one, G drive 250GB external

check my posting. I went back to flash 8.022 and most things started to work again....
QT logo with Question Mark and Blank screen sound ok on training videos
Posted: Mar 19, 2007 12:35 AM
Reply Email
I suddenly had all sort of problems (before 10.4.9) with QT logo and Question Marks throughout all browsers and also suddenly unable to continue training programs using files such as "avibasicmono.htm" and "introbasicmono.htm" .
finally think I have solved the QT logo by replacing Flash 9.0 with the old 8.022.
I could now also see current issues of magazines again on a site www.picturebusiness.uk.com (weird naming).
however I am not able to see the training videos at all but I hear the AVI files
Macosx 10.4.9 Quicktime 7.1.3 (removed 7.1.5 to try that option did not work)
will stay with what works until I hear more...

Can PRIME-NCS-APL-K9 upgraded from 2.0 to 2.2

Dears,
I have Cisco prime infrastructure Appliance "PRIME-NCS-APL-K9 " use this version 2.0.0.0.294 and have the following spec.
Total RAM Memory: 16278820 kB
CPU Core Count: 16
Disk 0: Capacity: 437.90 GB
can i upgrade it from 2.0.0.0.294 to CPI 2.2
Waiting your feedback plz.
Regards,

Users deploying the Prime Infrastructure physical appliance can choose from the Gen 1 or Gen 2 options shown in Table 2. The The Gen 1 and Gen 2 physical appliance capacities match those of the virtual appliance Standard and Professional options, respectively.
http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-2/quickstart/guide/cpi_qsg.html#53444
Table 2 Prime Infrastructure Physical Appliance Options
Physical Appliance Options
2.X Option
Gen 1
Gen 2 3
Appliance Image Format
Bare Metal/ISO
Bare Metal/ISO
Equivalent 1.x Option
Physical Appliance
Physical Appliance
Hardware Specifications
CPU (cores/threads)
8 C/16 T
10 C/20 T
Memory
16 GB
64 GB
Disk Capacity
4x300 GB
4x900 GB
RAID Level
RAID 5
RAID 10
Disk I/O Speed
200 MBps
200 MBps

Problems after upgrade bios to v4.3 - P67A-GD65

Hi to everybody,
I was having a problems after upgrade bios to v4.3 of my mainboard P67A-GD65.
After upgraded bios version (FW) its interface was changed and seemed better. also some specifiactions upgraded that i am now able to follow information of bios in my windows. with Control Center.
1) first of all after bios upgrade XMP memory section can only be enable şf ş choose OC geniue on. but with this my cpu warm till 98C degree. because i have only stock cpu cooler of intel.
in normal mode xmp can not be activated so that my memory that corsair vengeance dd3 1600mhz works at 1333mhz only.
Also there was information about what is new in this version of bios fw as:
- Enhanced PCI-E display card performance.
- Improved memory compatibility.
2) second problem that i have i wanted to turn cpu leds which were located above cpu slot blue leds. once i turn them off and it is ok. but when shutdown computer and restart it turn on itself.
so may be there have benn occured a problem that mb can not save edited settings correctly?
3) For last i could not find Winki 3 OS/linuz anywhere is there a link to it to integrate to my mb?
Thanks for your replies from now on.
Greetings.

Quote from: momosala on 02-April-13, 17:54:22
I think you had better to flash back to beta 4.39 bios, here : https://forum-en.msi.com/index.php?topic=164135.msg1214789#msg1214789
And use and install on USB key MSI Forum HQ USB flashing tool from here : https://forum-en.msi.com/index.php?topic=108079.msg800577#msg800577
Flash using method 1.
And tell us if that works.
thank you for reply that fast i will try asap and tell here.
Btw, have you ever face a problem as i wrote above?

Problems after upgrade: Leopard to Leopard no longer works

My sister upgraded to Leopard on her iMac(c2d) to Leopard yesterday. Earlier in the day we were able to do video chats with a number of people(her machine Tiger to Fathers machine Leopard). However, since upgrading, we've experienced weird behavior for video chats. Basically in her window she won't see her image(the small one), and I don't see her at all. We've tested this out with a number of other iChat accounts and get the same results. Btw, all machines that are chatting with her are using Leopard. Also, all other forms/capabilities work: screen sharing, sharing of pictures, audio chats.
Anyone out there have similar problems after upgrading from Tiger to Leopard? I have done the usual adjustments of bandwidth and QT settings, as well as restarts. What else should I try?
tia,
n

I finally resolved this problem: I think the issues/steps would be helpful for anyone who experiences iSight off or not working problems after upgrading to Leopard(then to 10.5.1) on a intel 20" iMac :
Problem:
-If you have an internal iSight on an iMac and your camera works fine in Tiger
-If you upgrade to Leopard
-If Chat camera doesn't show your image (iSight off) even though the green light is on
-You can see the other persons video on iChat
-Your friends can here you and you can share screens, files, etc.....everything but have them see you
These are the initial steps I took:
- Deleted the pLists(or stored preferences for the Application) described at the top of this thread
- Was told it might be slow internet connection so did various things: disconnected other computers, changed wireless to "G" only
- Specifically Opened of ports spec'd for Leopard on router (even though I hadn't needed to do this under Tiger)
- Tried chats with various people on various fast/slow networks
- Restarted all aspects of the network: router, wireless access point, computer
- Checked to see if the iSight was shown in 'System Profiler'. It was found in 'About This Mac->More Info->System Profiler->USB'
- Clicked Video icon in iChat Buddies window(to the right of your name) and coudn't see my image
- Opened 'PhotoBooth' and coudn't see my image(black screen)
- Opened iMovie and couldn't capture video via the iSight(black screen)
- Opened iChat->Preferences->Video and couldn't see my image
- Validated that 'Camera is Enabled' in iChat->Video->Camera is Enabled
If you are experiencing a similar problem with you built-in iSight, I would probably focus on the last 5 things that I did. What they showed me was that the iSight was just not capturing video even though it was capturing sound in 3 different applications.
The solution to iSight Off or iSight Not Responding or No Video is......reset your computer! I had thought my sister performed this but it turns out she hadn't. Here's the link to this procedure:
http://docs.info.apple.com/article.html?artnum=303446
Very easy to do though: Power off computer and unplug all cables, including power cable for at least 15 seconds. Plug everything back in and power up the computer and retry clicking on the 'Video' icon next to your login name. If you see yourself then...problem is solved.
While I eventually found posts in several other forums, it took me the better part of a week. To try this simple step. I wish I had done so straight away. Oy. I guess I learned a lot about ports, speed etc.
I hope this helps.

Problems after upgrading to iTunes version 6

Hello,
I've been going through the threads a lot since I have had problems after upgrading to iTunes v. 6. It looks like a lot of people have had the same issues, and I have tried some things that were recommended. After I upgraded, iTunes would not open. I tried:
1. deleting sidb file
2. doing the msconfig thing suggested in discussion boards
3. going into safe mode and deleting 4 and 6 letter weird files in DOS - I found 3 that I deleted
iTunes worked after this -- then I bought a song and it said my computer was not authorized, after I authorized computer (that never happened before), iTunes worked for about 15 more minutes and then closed down abruptly. I haven't been able to open it since.
I also downloaded Spybot search & destroy and that did not find anything. I am using McAfee, and have scanned for viruses with McAfee and AdAware.
Now, when I restart my computer, a bunch of windows pop up with Chinese/Japanese looking characters and say that device (I think) was not found. I seem to be able to use everything except iTunes and Quicktime. When I open the Task Manager, iPodService.exe and iTunesHelper.exe and qttask.exe are there, but when I click on Quicktime or iTunes the file flashes in Task Manager and then disappears.
I'm not sure where to go from here.
Any help would be apppreciated -- I'd like to be able to open iTunes!

Hello,
I used Nickroo's post:
I was able to get iTunes launched (with the help of Tech Support) in a very unsafe environment. I owe it to those who may need this after me. It will get you going, but you will be extremely vulnerable to internet virus assaults. Please do not use this approach, until you have exhausted every other available solution for your issue in the KB.
There are three Steps 1) Uninstall 2) Disble and 3) Reinstall.
UNISTALL Uninstall iTunes using Windows utility Add Remove Program available in Control Panel.
DISABLE Disable all third party System Services and Startup Items using using MSCONFIG utility as described in Service Document http://docs.info.apple.com/article.html?artnum=302538
RE-INSTALL Re-install iTunes6 + QT7. Launch it under the Selective Startup Option.
It worked ! You realize among other things at this point you have your Antivirus and Firewall disabled. When I started my computer in the Normal Startup Option, iTunes fails to work again. So I have ahead of me the long and ardous task of ruling out the service that is causing conflict with iTunes6. Then work with the software vendor to arrive at a solution.
This seems to have worked so far- I haven't started to go through ruling out what made iTunes not work; I also haven't tried to connect my iPod or burn a CD, so we'll see.
Windows XP

Permission problems after upgrade to 10.5 on early Power PC G5 Tower

Permissions problems after upgrading to 10.5 on a client power PC (early) G5 tower.
Problems include folders that are created on XServe via this client do not allow any one else including this client to access. All other clients running 10.5, which happen to be newer Intel machines do not have this problem. Repairing permissions, updating to 10.5.1, try to manually correct permissions have all failed to repair the situation. All clients log onto the XServe with the same user/password. This client has since been downgraded back to 10.4.9 and has no issues.
The Xserve runs 10.3.9, any help would be greatly appreciated.
We have read through the forums regarding permission problems after upgrading and even tried some tips found here.

You really should check things out first before speaking.
Here are the requirements for 10.5;
Mac OS X v10.5 Leopard requires:
A Mac computer with an Intel, PowerPC G5, or Power PC G4 (867 MHz or faster) processor
512 MB memory or more
A DVD drive for installation
9 GB of available disk space or more
Some features require a compatible Internet service provider, fees may apply.
Some features require Apple's MobileMe service; fees apply.
Allan

Layouts problem after upgrade

Hello, I have a problem after upgrade from 2007 to 8.81 PL 05.
Since we upgrade SAP, the layout changed.
For example, in a credit note if it has 3 lines, in the layout will appear 2 lines in a page and 1 in other page.
if the credit note has 4 lines, in the layout will appear 3 lines in a page and 1 in other page.
What could it be?
Thanks in advance.

Hi!
lines are not duplicated, they just printed on different pages:
- if doc has just 2 lines - printed form is good
- if doc has 3 items, two of them are printed on the first page, 3d - on the second page
- if doc has 4 items, 3 of them are printed on the first page, 4th - on the second page
When we are printing directly from the server everything is working fine. But printing from all Clients gives us this issue that is described above.
SAP re-installation for all users will take too much time. May be exist any other option that we can try?
we really appreciate your help
Natalia

Problem after upgrading to ICS 4.0.4

i have different problem after upgrading my SE Live with Walkman to ICS 4.0. After upgrading, my sd card always full. I have try to remove some files but after that it full again. Finaly i found that there are tumbnail file with size precisely same with my empty space. I delete that file, but the empty space not recover, its only recover after unmounting sd card. But its not hold for long time, after one minutes its happen again, my sd card is back fully again, and the same file is back to exist. Please help me, is that a virus or bugs from ICS?? i very frustation with this case
thanx for your help

Do you have many pictures?
Have your tried to reinstall the phone software using SUS to check if the problem remains?
http://www.sonymobile.com/gb/tools/update-service/
- Community Manager Sony Xperia Support Forum
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

Several problems after upgrading to iO6

My iphone is with multiple problems after upgrading to iOS 6. Applications are closing alone, the screen goes black and then back to the home screen. does not connect to internet (3G and Wi-Fi) connections as cutting. Throw another quick update to fix this, or do I have to change to the Galaxy SIII; Iphone is Terrible!!

Try the Padma extension.
*Padma: https://addons.mozilla.org/firefox/addon/padma/

Login problem after upgrade to mavericks

Hi, i have login problem after upgrade from mountain lion to movericks in imac, I did enter the correct password But back to the login page again.

Hi cpuman8,
Thanks for visiting Apple Support Communities.
If you're not able to log in to your user account after upgrading, try resetting your password using the method in this article:
Resetting the original administrator account password
In OS X Lion or later, you can reset your user password with your Apple ID.
OS X: Changing or resetting an account password
http://support.apple.com/kb/ht1274
Best Regards,
Jeremy

Apple TV problem after upgrading to iTunes 7.5

PROBLEM: After upgrading to 7.5, Apple TV no longer recognized iTunes and vice versa.
ATTEMPTED SOLUTIONS: Removed and reinstalled iTunes 7.5 from scratch. Reset @TV to Factory Defaults and reconfigured. Removed Apple TV from iTunes Preferences/Apple TV/Remove Apple TV.
iTunes no longer finds @TV, either in the Preferences/Apple TV pane, or in the Device List. Everything worked perfectly before the 7.5 upgrade. All other features and devices working fine. Have reviewed all postings and eliminated the possibility of firewall or port problems.
Suggestions welcome! Thanks.

I have partially resolved the problem. Something with the 7.5 upgrade changed the network protocols being used by the Apple TV... switching to a wired network from end to end with a full shut down and reboot has the @TV back online... I am still working on trying to solve the wireless side of the equation.

Why am I facing so many problem after upgrading to ios7, my phone hangs/stuck many times, applications just stop working and close themselves, battery drainage,Facebook and all applications don't work properly. What should I do? They punished me for upgra

I'm using iPhone 5
Why am I facing so many problem after upgrading to ios7, my phone hangs/stuck many times, applications just stop working and close themselves, battery drainage,Facebook and all applications don't work properly. What should I do? They punished me for upgrading to ios7. I now hate apple and I'm thing of getting samsung.

Basic troubleshooting
Reset
Restore with backup
Restore as new ( better )

Problem after upgrading to iPhone iOS 7

Gentlemen Apple
I have a problem after upgrading to iPhone iOS 7
Required to calculate the icloud lost me
<Email Edited by Host>

I have the same issue after upgrad my iphone 5 to IOS7?? what is the reason and what is the solution?

Printer Problems after upgrade to Lion

Does anyone have this printer problem after upgrading to Lion. A perfectly functioning laser printer on my network prior to upgrade - now the network seems to drop the printer and show it as "not connected" approximately every 30 minutes ???

Hi Paul,
Been away and just got back to this issue.
Thanks for the info. The OKI site has now posted a list of all their Printers and their relative drivers for compatibility with "Lion". My machine is due an updated driver from OKI in Mid Decmber according to this notice.
Meanwhile, as the printer does work with some tweaking I guess I will use the work around until the new driver is available. My legacy printers that i use for special jobs both work and as I do not have the disks for their drivers I am loathe to re-set the printer system at this time.
Thanks for your assistance in this issue.
Regards,
Mike, Rustington.

Problem after upgrade a PRIME-NCS-APL-K9 from version 1.1.0.58 to Prime Infrastructure 1.2

Similar Messages

Maybe you are looking for