Problem booting from external DVD drive on Lenovo S10e

Hi,
I recently purchased a new Lenovo S10e ideapad, a few weeks prior to that I purchased an external DVD rewriter drive manufactured by LG, the drive works perfectly on every computer I try with the exception of the Lenovo ideapad S10e.
The thing is that the drive is being recognized and installed by the Windows XP Home Edition the S10e came with but when I try to boot a bootable CD using then drive on the S10e ideapad I almost alwasy fail to do so.
I set the S10e BIOS to have the USB CDROM as first boot device, in addition I used the F12 key to use the boot menu to choose the boot device, in 9 out 0f 10 atempts my external drive will not show in the boot menu and when choosing the enter setup option I see that the BIOS do not list it as the USB CDROM, instead it says "USB CDROM:" rather than have the drive name after it.
In the 1 time out of 10 it does work the BIOS seem to be identifying the drive and it shows in the boot menu, however I cannot work with it for a more than 1 minute without it stopped being recognized again.
The problem seems very strange to me as the drive works under the windows operating system and do not have any problem whatsoever on other computers, I have tested the external drive on my PC, another Mini Laptop from LG and a GIGABYTE Laptop (Normal one), all of which had no problems recognizing the external drive and booting from it.
I will really appreciate if I can get some help with the problem.
Thanks.

I've had a similar issue with X61 and the external DVD drive from Lenovo.
In my case, it was the power issue. On the back of the drive, there is a small table says that the drive needs a 3.0A 5V power input. One USB 2.0 port can only provide 0.5A. I don't know if the drive has any special, low power mode, but I suspect that even if it has, 0.5A is still not enough to fully power it. I've checked the current with the multimeter, and at peak times, the drive draws 550mA. Even then, it makes a stuttering sound for a few seconds, before finally spinning the DVD disk. I've also noticed that the DVD works most of the times when it's connected to the left USB port. That may be because of how the laptop's internal power circuicity is laid out (+separate USB host controller for each 'side' of the laptop). Another thing that seems to help is to disable all 5V driven devices that the laptop uses: the wifi card, bluetooth, any additional devices connected to the USB bus / to the ethernet port / SD card port (I'm not actually sure which of the devices are 5V and which are 3.3V, but the best option is to disable all of them), maybe even remove the battery (if it's charging). Finally, the DVD drive works better if the laptop was turned on and runnig for some time, rather than it being turned on "a minute before". Also, in the BIOS, there is a setting that changes the speed of the DVD drive, but switching it to "low" didn't seem to affect the external drive (at least not before Windows boots up).

Similar Messages

Ibook g3 M2453 boot from external DVD drive

Hi, I'm Simon from Germany.
I have an iBook M2453 Mac OS X and a lot of dvds.
But the iBook has no DVD drive. So I bought an external DVD drive. But no matter what I do during boot (press the C key or alt)
I can not boot from external DVD drive.
Please help me
Thank you.
Simon.
PS: I have translated the text using Google translate

Hi Simon,
the iBook is able to boot from USB, but this is not expected behaviour and not supported by Apple.
http://support.apple.com/kb/TA20554
There are some external enclosures that do the trick.
But only when you press ALT after Power on. (Select a startup volume via the Startup Manager)
External enclosures with Prolific PL-3507 chipset (Firewire/USB Combo)
You will find them on Ebay Germany
I have a Delock IDE>USB 2.0 enclosure for 2,5" HDs
http://www.delock.com/produkte/gruppen/Geh%C3%A4use/Delock_25_external_enclosure _USB20_42365.html?setLanguage=EN
that works also.
Hallo Simon,
das läuft nur mit einigen wenigen externen Gehäusen. Such auf Ebay nach "PL-3507"
und nimm eins mit Firewire und USB Anschlüssen.
Ein Festplattengehäuse von Delock für 2,5" Festplatten ging auch ( Link oben)
Ein Boot ist nur möglich wenn du die ALT Taste nach dem Einschalten drückst und dann über den Startup manager dein Boot volume auswählst.

All users GONE except for "Other"...and CANNOT boot from External DVD drive

I booted the iMac (Intel...the last one with the White Bezel) tonight, and all of my users were GONE except for "Other." The internal Superdrive has had a disc jammed in it for months, so instead I have an OWC external USB/FW400/FW800 DVD drive. Snow Leaopard.
I need to boot from the SL install disc, but that must go into the external drive...which, as it's been since I upgraded to SL, the Mac sometimes sees and sometimes doesn't. Right now it can't see it. Which leaves me a big pile of crap, doesn't it?
So, what to do? I can't boot the internal drive because it's jammed with a DVD (or I spend $300 to replace what should be a $20 optical drive in it), I can't boot the external DVD drive because the iMac w/Snow Lepeord can't see it, and, meanwhile, all of my photos, etc., are on my Time Machine backup drive...which, as long as I can't do any of the above, just sits there...useless.
Can you tell I'm a bit frustrated with this?
I've reset the PRAM. I've rebooted. I've held down all sorts of combinations of keys. I've tried every single interface type on the external drive and the same thing - the drive can't be seen by the computer.
Has the internal hard drive failed? Nope. I'm tying this using the Firefox browser that's running on my Windows XP installation via Boot Camp on the internal hard drive.

Thanks, but no luck so far.
I have an old iMac G3 downstairs, and I connected it to the machine via Firewire. I could see the disk on the 24" iMac, its folders, etc. I wanted to see if I could install OS X via Target Disk Mode from the old machine to the new one, but it's a PowerPC machine and you can't do that. Maybe you can't do that from ANY iMac...I'm not that experienced.
Now the iMac isn't booting at all to Windows via Boot Camp - it's been booting for 45 minutes now with the "WinXP" logo, but nothing. I'm about to throw it in the car and haul it over to my parents, who have both a Powerbook and a 27" iMac. Maybe it'll work there. Who knows.
Other ideas...replace the internal hard drive (cheap)...if that doesn't work, I'll just sell the thing. I'm not going to sink $300 into the thing when I can get a new machine for around $600-$700. I may go to a Windows7 machine on the desktop and a Powerbook...maybe even an iPad.
I really want to love this iMac. It's my first (well, I did have the G3, but that was just to play with) Mac. It's given me a ton of problems since I bought it new. It's always been a "stock" machine - nothing weird done to it. I was hit with an iMovie update once, and that broke iMovie. Even the new iLife 2009 didn't fix it. Then, the internal optical disk drive failed. I couldn't believe that Apple used a proprietary optical drive rather than a stock Pioneer model. Price for the drive alone? $200.
I installed Snow Leopard 2 months ago, and that completely broke my ability to use external optical drives. Sometimes they work...most times they don't. This is an ongoing problem that many people are having (check the forums)...but no fix. Where does that leave me? With a useless computer.
So, I've boiled it down to this: I love the Mac software. I hate the hardware. Sure, it's pretty, but if something goes wrong, get ready to pay. I hate that Apple knows about problems, yet does nothing to address them, like the problem with external optical drives and Snow Leopard.
I bought the Mac because I was sick of Microsoft not being able to simply produce an OS full of security holes. Often times I read people bashing supposed "driver ****" with Windows, but look at what users of Windows machine are demanding of Microsoft - "please make my software compatible with the trillions of combinations of hardware that can run the os...all the way back to stuff that was created in the mid 1990s." Meanwhile, from my experience, Apple can't get their software to work with their own proprietary, supposedly vertically-controlled hardware.
Windows7 is a not bad OS. It's got it's faults, of course. But, if my optical drive failed in a Windows box, I'd have it replaced in 10 minutes...with a bluray drive...that can write...for under $100.
I use my computer for pictures, etc. In fact, we were ready to send off to iPhoto for our yearly photo books. That's not going to happen, as the photos are forever trapped on my Time Machine backup drive (lesson learned: dump photos to a generic format...fat32 works...just in case you decide to switch from Mac to Win7). iLife is great. MS Office is great, too, on the Mac. I love the little things the Mac does right.
After years of screwing around with my Windows box, I wanted a computer that acted like a consumer electronic device. That's not what I've gotten.
Ugh, so now do I buy a Mac Mini for $700, a new iMac for $1,400, or a Macbook Pro and a mac mini?
...or...do I continue to work within this silly Ubuntu Linux world?
Whatever the answer, I wish I didn't have to ask the question now.

Restore Disc Will Not Boot From External DVD Drive

I am using an original MacBook Pro that I decided could use a good restore, and started to clean house. The optical drive is broken, so I am using an external USB drive. I inserted the restore disc that came with the computer (It has OS X 10.4.6 on it), erased my HD, and proceeded to install Tiger. However, setup froze while installing Photobooth, and I was forced to shut down the computer.
I'm trying to get my Macbook Pro to boot from the restore disc that came with it so I can try setup again, but it won't work. If I hold C during the boot, I get a flashing folder with a question mark over it. If I hold option, I get a cursor, but just a blank, gray screen. In both instances, the external DVD drive is active and reading the disc, but I'm not getting any results on the screen. I've also reset PRAM.
If I can just get my computer to boot from the disc, I should be able to get back on track. Thanks.

When I press option during boot, nothing happens. Just a gray screen and cursor, like I described above. I haven't been able to test the external drive yet on another mac to see if it is bootable because I can't find the other computer's boot disc at the moment, but I'll try later with something else.
I have been able to access the drive through Target Disk mode successfully though. Is there something in particular I should do with the files? The folders are:
Applications
cores
dev
etc
Library
OSInstall.mpkg.998YblbM
System
tmp
Users
var
Volumes

The Air cannot boot from external dvd-drive

Hi!
I am using my rev.2 air, 1.86 Mhz prosessor, 120 GB HDD, leopard 10.5.7 with a Samsung writemaster external dvd-writer, but I am having problems booting from it.
When I try to boot (pressing option) I can choose the disc and the applesymbol will appear, but the spinning wheel below does not, and the screen just stay the same until I cut the power.
I have tried to boot both the original OS X-disc and Windows 7 (both through boot camp and normal restart) with the same result.
Any help will be...well, helpfull

Not sure if this will help - but whenever I need to boot from an install disc on my MBA - i turn on the MBA and hold the 'c' key until i hear it loading the disc. that's how I boot off of optical discs... worth a try?

Booting from external dvd drive

hi all,
my optical drive in the 17" mbpro (1st gen) has finally packed up and it doesn't make financial sense to replace it when the external lacie units are half the price. Before i make the plunge, does anyone know of any limitations, if any, of using the external drive as the boot device for installs?
Thanks

hey guys,
my cd drive is fried too and i am using an external USB cd/dvd drive instead.
But now i just bought leopard and to install it i need to set the mac to boot from the drive.
The problem is that even when i press alt/option key at startup, the drive is not inculed on the available list as if it is not recognised.
Can somebody help me out please?
Thanks

Booting From External DVD Drive Thru USB to install OS Tiger DVD

Hi,
I would like to reformat my iBook G4 from Panther to Tiger. I dont have DVD drive internally. I've got the DVD ROM of Tiger and external USB DVD Drive. Tell me the possible ways to do the installation beside Firewire connection.
Please help me.

Hi Nik,
AFAIK you cannot boot from USB devices. You could give it try by inserting the Tiger DVD into the external drive and rebooting your Mac while holding the "alt" key. If your DVD drive was bootable then -after a while- the DVD should come up as an option to boot from. But this is not likely to happen.
The best way to get Tiger on your iBook - unless you have anothet Mac with a DVD drive lying around - is to get the Media Exchange form from this website and to exchange your DVD for a set of CDs (minus a handling fee).
-Petra

Password problem booting from external hard drive

I have an eMac and just installed Leopard. BUT now I can't use Photoshop and Quark from within Classic because it's not available with Leopard. I've installed my old 10.3 OS on my external hard drive, and when I boot up from that (using the Option key), after I choose the hard drive as the startup disc, I am asked for my admin password. When I type that in, the dialog box jiggles from side to side for a moment and blanks out the password, asking for it again.
How can I boot up 10.3 from the external hard drive? Help -- I need to use the Classic environment for a job! Thanks for any help --

Hi, Jeff --
Well, I think my problem is finally solved, thanks (partly) to your help. Just to help other folks who have this problem, I'm going to state briefly how I fixed it:
-- I did an Erase and Install on the Seagate AFTER spending all day burning 30 CDs with the archived files I'd taken off the Mac but didn't want to lose.
-- After that, I could indeed boot up the Mac from the Seagate in 10.3 and all seemed fine.
-- But I made the mistake of doing a full backup to the Seagate from the Mac (which took two hours).
-- After that, I couldn't boot up the Seagate at all -- I spent two 20-minute periods waiting for it to get off the gray screen with the Apple log, to no avail. A friend of mine suggested that the backup program might be the problem.
-- After some trepidation but knowing that I already had everything I needed on those 30 CDs, I decided to experiment and partition the Seagate (via Disc Utility) into one partition with only the 10.3 install on it and the other with whatever files I needed, including the applications I needed to open in 10.3.
-- That worked!! I can now boot up the Seagate "10.3 drive" and access all the files and applications I need from the Seagate "Backup Drive."
I hope this information helps someone else in the same predicament.
Thanks for all your help and patience; your suggestion to do an Erase and Install was the right move to get me started.
Eileen

Problems booting from external firewire drive

Here's a weird one...
I'm trying to help a buddy with a 3rd gen MBP and a new WD 'My Studio' firewire external drive.
He can mount and use the drive but is unable to boot from it. When starting up his machine with option, the drive doesn't show up as selection. The really odd part is the drive does work if plugged in with the USB cable!
The drive in question DOES work as expected on my 5th gen MBP with firewire. Further, I can stert my MBP in target disc mode and it will function as expected as a bootable external drive for his machine. The system in question was cloned with Carbon Copy Cloner. And again, it boots from my MBP.
I've tried different sets of cables (even though everything works on my system). I actually had him send the drive back for warranty replacement but of course the new one behaves the same way.
What could be the cause of apparently certain firewire drives not being bootable (but otherwise working) on a 3rd gen MBP? The intended workflow is to be studio/audio work so using the USB connection for a workaround would not be an option.
Any clues? Windows is not even installed on any of these machines!

baltwo wrote:
FWIW, many WD HDs won't boot Macs and booting Macs isn't supported. Details at their site. That's the main reason I never recommend their crappy HDs.
Actually I'm very familiar with that list- spent a lot of time looking at this past week!
Ironically, the majority of that page is a list of drives which they claim WILL boot Macs. In fact, the list is entitled "List of Mac-bootable WD external drives..."
And yep, mine is on there...on the list that reads "The following external hard drives should be bootable on Intel-based Mac computers systems through FireWire (1394a/b)" is "MyBook Studio" as well as my drive model number.
But that's all beside the point. Like you, I couldn't recommend their drives at this point. At least make sure if you buy one that the vendor has a good return policy.
Dave

Problems booting from external DVD writer.

I have used an Optibay to put a second HD in my MBP 3,1 2.2 GHz in place of the original burner.
I am using a Freecom Mobile DVD LS Pro instead of the internal.
The Freecom will boot the original install disk, Snow Leopard and Leopard disks, and a Techtool Pro disk.
But it won't boot any Diskwarrior disks, or any Paragon Rescue disks, or the EFI Windows 7 disk I made and used to install Windows 7 while the internal DVD writer was still fitted.
All the disks boot my Mac Pro fine, so the problem is not the actual disks.
I have tried with the Freecom connected both USB and Firewire.
I will probably put the original burner back, but before doing so, I wanted to ask if there are any other explanations, or anything I could do to make these disks boot?
If there is a different brand of external known to boot better, I would consider getting it.
Thanks for any input.

I put the original burner back in, and now the other disks are booting OK!

Macbook pro cant boot from external dvd device please help !!!!

hello everyone please help me i have macbook pro 2011 core i5 version
i just installed 2.5 ssd as second hdd
i cant boot from external dvd device to install any os the external dvd keeps on spining and mac is just thinking it doesnt show press any key to install
it shows the device when a boot into mac parition
i am trying to install windows on origianl 500 gb hdd and linux on ssd
but not luck
the external dvd drive works i pluged into my pc and it works
please help thansk in advance
200 gb mac
300 gb windows
120 ssd linux

I do not know about Disk Warrior but if you have a compatible OSX on an external HDD you certainly can boot the MBP. Use startup manager:
https://support.apple.com/en-us/ht1310
Ciao.

Boot from external Firewire Drive-cannot repair or optimize internal drive.

Hi all
Connected my new 300 GB Seagate External Firewire Hard Drive today.
Installed Tiger from DVD. Updated to 10.4.3.
Installed Tech Tool Pro 4. Updated to 4.1.1.
Booted from External Firewire Drive.
Disk Utility cannot Verify or Repair internal drive. Does not say or do anything.
Tech Tool Pro cannot repair volume or optimize. Says, "Cannot Unmount Volume."
Is there a fix for this?
Thank you for the help!
Jeff
eMac 800 nVidia. Mac OS X (10.4.3) 160 GB Internal HD. Pioneer Superdrive. 1 GB RAM.

Hi
I did name the new external completely different from the internal.
After booting from the external Firewire Hard Drive, I tried running Disk Utility and Tech Tool Pro from both drives. No matter which drive I run the Utilities from the same things happen every time...
Nothing happens when trying to use Disk Utility to Verify Volume on internal eMac Drive.
Tech Tool Pro says, "Cannot unmount volume" when trying to check Volume or Optimize internal drive.

Booting from CD/DVD drive on HP Pavilion 17-e158sm Notebook PC

Hello,
I have a problem with my new Notebook. When I bought the computer it had free dots on it, soo i decidet to instal windows 7 on until I could get windows 8.1. The only problem was that windows 7 was 32bit. Now I have windows 8.1 64 bit on a DVD, soo I cant updait my widows 7, because it is 32 bit. The only way is to instal my new windows by booting from CD/DVD drive in BIOS. But I here is the problem. The notebook doesnt want to boot from DVD, it starts Windows 7 every time. I tried everything, like changeing the Boot order. Please help.
Hope my english is good enought.

Have you checked BIOS to see if Secure Boot is enabled? IF so disable it. Enable Legacy .Clear all secure boot keys.
Btw.When you installed Windows 7 did you boot from the dvd?
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others**

Satellite C655D-S5303 will not boot from cd/dvd drive

I have already set the boot order in the BIOS to boot from cd/dvd drive first and it still goes straight to the HDD and starts Windows 7. I searched for this problem and found some people saying to switch it to CSM boot or disable secure boot but none of these options are available in the BIOS. I have it set to normal boot instead of fast so thats not the problem. Can anyone help me here? I am trying to reformat and reinstall Windows 7. I know the Windows 7 installation disk I have is good because I have used it in another computer and the cd/dvd drive works fine. I just can't get it to boot from the cd/dvd drive before the HDD.
Solved!
Go to Solution.

Satellite C655D-S5303
Downloads here.
Try setting the HDD to lowest boot priority. See Dave's solution in this message.
It's certainly easier to restore the hard disk to its original out-of-the-box contents using Toshiba recovery media. All the drivers and utilities are preinstalled in the proper order. Windows is preactivated.
If you failed to burn recovery discs, you can obtain recovery media from Toshiba. Scroll down to Get Recovery Media here
For instructions, see the section Restoring from recovery DVDs/media, which begins on p. 76 of the User's Guide.
Satellite/Satellite Pro C600 Series User’s Guide
If you want Windows 7 Professional, upgrading takes only minutes.
Upgrade to another edition of Windows 7 by using Windows Anytime Upgrade
-Jerry

Satellite C655D-S5303 will not boot from cd/dvd drive

I have already set the boot order in the BIOS to boot from cd/dvd drive first and it still goes straight to the HDD and starts Windows 7. I searched for this problem and found some people saying to switch it to CSM boot or disable secure boot but none of these options are available in the BIOS. I have it set to normal boot instead of fast so thats not the problem. Can anyone help me here? I am trying to reformat and reinstall Windows 7. I know the Windows 7 installation disk I have is good because I have used it in another computer and the cd/dvd drive works fine. I just can't get it to boot from the cd/dvd drive before the HDD.

Satellite C655D-S5303
Downloads here.
Try setting the HDD to lowest boot priority. See Dave's solution in this message.
It's certainly easier to restore the hard disk to its original out-of-the-box contents using Toshiba recovery media. All the drivers and utilities are preinstalled in the proper order. Windows is preactivated.
If you failed to burn recovery discs, you can obtain recovery media from Toshiba. Scroll down to Get Recovery Media here
For instructions, see the section Restoring from recovery DVDs/media, which begins on p. 76 of the User's Guide.
Satellite/Satellite Pro C600 Series User’s Guide
If you want Windows 7 Professional, upgrading takes only minutes.
Upgrade to another edition of Windows 7 by using Windows Anytime Upgrade

Problem booting from external DVD drive on Lenovo S10e

Similar Messages

Maybe you are looking for